Miscibility and Hydrogen Bonding Interactions in Blends of Poly(hydroxyether ketone) and Poly(4-vinyl pyridine)

The influence of silica nanoparticles on the tensile properties of poly(ethylene terephthalate)(PET) fibers was investigated. The results showed that mechanical properties of PET fibers were improved through nano‐silica incorporation. Two maxima of the modulus‐strain curves of PET/silica nanocomposites (PETS) fibers are always higher than those of pure PET (PET0) fibers. The results of microstructure investigations suggested that the amorphous orientation factor of PETS fibers is higher than that of PET0 fibers. It is suggested that the increase of amorphous orientation factor contributed to the improvement of tensile properties of PET fibers. Considering the difference in modulus‐strain curves of PET0 and PETS fibers, it is believed that the addition of nanoparticles not only improved the amorphous orientation factor but also changed the load units of PET fibers when strained, which also resulted in the improvement of tensile properties.     

A simple and effective route for the preparation of poly(vinylalcohol) (PVA) nanofibers containing gold nanoparticles by electrospinning method

Poly(vinylalcohol) (PVA) nanofibers containing gold nanoparticles have been simply obtained by electrospinning a solution containing gold nanoparticles without the additional step of introducing other stabilizing agents. The optical property of gold nanoparticles in PVA aqueous solution was observed by UV-visible absorption spectra. Morphology of the Au/PVA nanofibers and distribution of the gold nanoparticles were characterized by transmission electron microscopy (TEM). The structure transformation was characterized from PVA to PVA/Au composite by Fourier transform infrared spectroscopy (FTIR).     

Quantitative analysis of chromate (CrVI) by normal Raman spectroscopy and surface-enhanced Raman spectroscopy using poly(diallyldimethylammonium) chloride-capped gold nanoparticles

Chromate (Cr^VI) has emerged as a widespread environmental contaminant found in groundwater and surface water, and there is a great need for rapid detection and monitoring of this contaminant. Normal Raman scattering (NRS) spectroscopy with a detection limit of Cr^VI at concentrations of 0.2 g/L was attached. And surface-enhanced Raman scattering (SERS) spectroscopy technique was found to be capable of detecting Cr^VI at concentrations as low as 2.5 mg/L using poly(diallyldimethylammonium) chloride modified gold nanoparticles (PDDA-AuNPs) as a substrate. The SERS substrate was successfully fabricated by combining the selfassembly technique with a heat-treatment-based strategy using poly(diallyldimethylammonium) chloride (PDDA) as the reducing and stabilizing agents. With the 520 cm^?1 band of silicon as internal standard, band intensity ratios of Cr^VI to silicon, that is I ₉₀₂/I ₅₂₀, were found to have a quantitative relationship with a large concentration range of Cr^VI from 0.2 to 20.0 g/L for NRS (R ² = 0.994) and from 2.5 to 25.0 mg/L for SERS (R ² = 0.980), respectively. Besides, the SERS methodology was reproducible, and susceptible to the interference of pH value. The optimum pH for Cr^VI detection by SERS was 3.38. The application of NRS and SERS showed high practical potential for rapid screening and routine analysis of Cr^VI in environmental samples.     

Preparation and properties of morphology controlled poly(2-hydroxyethyl methacrylate)/poly(N-vinyl pyrrolidone) double networks for biomedical use

Poly(2-hydroxyethyl methacrylate)/poly(N-vinyl pyrrolidone) (PHEMA/PVP) double networks (DN) were prepared using a sequential method by incorporating a second network of crosslinked PVP into PHEMA. We found that the distributions of the two networks can be regulated just by modulating the morphology of the first network, thus giving expected high water content of these gels. Fourier transform infrared (FTIR) spectroscopy and scanning electronic microscopy (SEM) were used to confirm the structure of the DN. The incorporation of more hydrophilic PVP enhanced swelling ability of these gels. Because of improved hydrophilicity, the PHEMA/PVP DN exhibited higher loading capability for water-soluble substance than that of pure PHEMA, while showed a slower release rate than corresponding HEMA/NVP copolymer hydrogel. It is suggested that the DN gels are potential biomaterials for wound dressing, medical implants and other drug delivery systems.     

Preparation and characterization of poly(lactic acid)-grafted TiO2 nanoparticles with improved dispersions

Poly(lactic acid) (PLA)-grafted TiO₂ particles were prepared by in situ melt polycondensation of lactic acid onto the surface of TiO₂ nanoparticles. The resulting products were characterized by FTIR, XPS, TG-FTIR, XRD analysis and electron microscopy observation so as to have a better understanding of bonding between the graft polymer and nanoparticles. New characteristic peaks of Ti-carboxylic coordination bond, the changes in the relative intensities of the infrared absorption bands of graft polymer and the two decomposition stage of PLA-grafted TiO₂ confirmed that PLA was grafted on the surface of TiO₂ nanoparticles. By attachment of PLA, the PLA-grafted TiO₂ samples exhibited much better dispersion and a slightly larger particle size than bare TiO₂ particles. PLA-grafted TiO₂ nanoparticles will find wide applications in biomedical and eco-friendly materials, especially as fillers in PLA matrix.     

Influence of ion irradiation on the morphology, structure, and optical properties of gold nanoparticles synthesized in SiO2 and Al2O3 dielectric matrices

Irradiation of fused quartz (SiO₂) and sapphire (Al₂O₃) by Ne⁺ and F⁺ ions with medium energies and their subsequent annealing enables us to control the intensity and frequency of surface plasmon resonance in Au nanoparticles (NPs) synthesized in oxide matrices. The control process can be implemented because NPs dissolve during irradiation and undergo partial reconstruction at annealing. The degree of reconstruction depends on the matrix material and the type and dose of ions. It has been found that the difference in the results obtained by means of irradiation with ions with similar masses is substantially affected by the chemical nature of the ions. The composition, morphology, and structure of the unirradiated and irradiated layers are investigated by transmission electron microscopy, X-ray photoelectron spectroscopy, and spectroscopic ellipsometry.     

Dendronization of gold and CdSe/cdS (core-shell) quantum dots with tomalia type, thiol core, functionalized poly(amidoamine) (PAMAM) dendrons

Poly(amidoamine) (PAMAM) dendrimers containing disulfide cores (i.e., cystamine) and possessing carboxylic acid or hydroxyl terminal groups were reduced with dithiothreitol (DTT) to yield single site, thiol core, functionalized PAMAM dendron reagents. These thiol functionalized dendron reagents were used to surface modify (dendronize) both gold nanoparticles, as well as CdSe/CdS (core-shell) quantum dots (QDs). Dendronization involved self-assembly of the focal point thiol functional dendrons at the metal interface of both gold and CdSe/CdS QDs by ligand exchange of protective surfactants used for their synthesis. The synthesis, characterization and preliminary luminescence studies of these new dendritic hybrids are reported.     

Electro-optical properties of poly(2-ethynyl-N-hexylpyridinium bromide) and poly(2-ethynyl-N-hexylpyridinium iodide)

Poly(2-ethynyl-N-hexylpyridinium bromide) and poly(2-ethynyl-N-hexylpyridinium iodide) were synthesized by the direct polymerization of 2-ethynylpyridine and the corresponding n-hexyl halides without any additional initiator or catalyst under mild reaction condition. The polymerization proceeded well to give high yield of polymer. The polymer structures were characterized to have the conjugated polymer backbone system having N-hexylpyridyl moieties. The photoluminescence spectra of poly(2-ethynyl-N-hexylpyridinium bromide) and poly(2-ethynyl-N-hexylpyridinium iodide) showed that the photoluminescence peaks are located at 603 and 611 nm corresponding to the photon energy of 2.06 and 2.03 eV, respectively. The electrochemical properties of the resulting polymers were also measured and discussed.     

Cytotoxic evaluation of N-isopropylacrylamide monomers and temperature-sensitive poly(N-isopropylacrylamide) nanoparticles

The objective of this research project is to investigate the biocompatibility of N-isopropylacrylamide (NIPAAm) monomers and poly(N-isopropylacrylamide) (PNIPAAm) nanoparticles in vitro. PNIPAAm nanoparticles of different sizes were synthesized and characterized by transmission electron microscopy and dynamic light scattering. Cytotoxicity studies using MTS assays were conducted on fibroblasts, smooth muscle cells, and endothelial cells. In addition, the concentration of NIPAAm monomers remaining on PNIPAAm nanoparticles was determined using bromination and spectrophotometry. The cytotoxicity results did not show a significant difference in cell survival when cells were exposed to different particle sizes (100, 300, and 500 nm). Dose studies showed that all three cell types exposed to 100 nm PNIPAAm nanoparticles at concentrations less than or equal to 5 mg/mL were compatible, while cells exposed to NIPAAm monomers exhibited toxicity even at very low concentrations. We also found that 1 mg/mL concentration of 100 nm PNIPAAm nanoparticles was cytocompatible for 4 days, whereas NIPAAm monomers were cytotoxic after 24 h of exposure. Photomicrographs showed altered morphology in cells exposed to NIPAAm monomers, while cells exposed to PNIPAAm nanoparticles maintained their normal morphology. Finally, a very low concentration of NIPAAm monomers remained on the PNIPAAm nanoparticles after synthesis and dialysis. Our results demonstrate that NIPAAm monomers are cytotoxic, whereas PNIPAAm nanoparticles are compatible at 5 mg/mL concentration or below for fibrobasts, smooth muscle cells, and endothelial cells.     

2-三氟甲基吡啶的转动光谱及分子结构研究

本文测定了2-三氟甲基吡啶在2∽20 GHz频率范围内的高分辨转动光谱. 测定了转动常数、¹⁴N核四极耦合常数及离心畸变常数等一系列光谱参数. 同时还在自然丰度下测定了5个¹³C和1个¹⁴N单取代同位素异数体的光谱数据. 实验结果结合从头算准确地推导出2-三氟甲基吡啶的骨架结构. 实验测得同位素异数体的平面转动惯量P_cc数值均为44.46 u?²,表明此分子具有C_s对称性. 此外,本文计算了吡啶、2-氟吡啶、2-甲基吡啶和2-三氟甲基吡啶的分子表面静电势,以此分析了三氟甲基的取代对电子分布的影响.     

Microflow reactor synthesis of palladium nanoparticles stabilized with poly(benzyl ether) dendron ligands

A simple glass capillary microflow reactor system has been applied for the synthesis of palladium nanoparticles by thermal decomposition of palladium acetate (Pd(OAc)₂) in diphenyl ether in the presence of poly(benzyl ether) dendron ligands (PBED Gn-NH₂, n = 1–3) as a stabilizer. Effect of hydrodynamic parameters (capillary diameter, linear flow rate, volume flow rate, and reaction temperature) and concentrations (precursor and stabilizer) on the particle size was investigated. The particle size can be controlled by varying linear flow rate and temperature as well as ligand/precursor concentration ratio. Volume flow rate does not affect the particle size when the linear flow rate is held constant for different capillary diameters (150–320 μm). Unlike batch systems, in this microreactor system, smaller particles are produced at low ligand concentrations when the molar ratio of the ligand to metal precursor ranged from 1 to 5. As another characteristic of the microreactor synthesis, the concentration of the Pd precursor can be increased (up to 27 mM) with maintaining a constant particle size (3.1 ± 0.2 nm) and a good monodispersity, while in the batch system a significant increase and broadening in the particle size are observed with increasing precursor concentration.     

Anti-corrosive properties of polyaniline,poly(2-toluidine), and poly(aniline-co-2-toluidine) coatings on stainless steel

This study examines the use of polyaniline (PANi), poly(2-toluidine) (PT), and poly(aniline-co-2-toluidine) (co-PT) for corrosion protection of 304-stainless steel (SS) in 0.5 M HCl solution. The PANi, PT, and co-PT coatings were synthesized on SS substrates under cyclic voltammetric (CV) conditions from acetonitrile solution using tetrabuthylammonium perchlorate (TBAP) as supporting electrolyte and perchloric acid (HClO₄) as acid. These coatings were characterized by CV, FTIR, and UV–vis spectroscopy. The ability of PANi, PT, and co-PT to serve as corrosion protective coatings for SS was examined by open circuit potential-time (E_ocp-time), potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) measurements. The results of this study reveal that PANi, PT, and co-PT acts as corrosion protective coatings on SS and every coating gives protection efficiency of greater than 80% after 48 h of immersion in corrosive test solution.     

Evaluation of the sonosensitizing properties of nano-graphene oxide in comparison with iron oxide and gold nanoparticles

In cancer hyperthermia, ultrasound is considered as an appropriate source of energy to achieve desired therapeutic levels of heating. It is assumed that such a heating is targeted to cancer cells by using nanoparticles as sonosensitization agents. Here, we report the sonosensitizing effects of Nano-Graphene Oxide (NGO) and compare them with gold nanoparticles (AuNPs), Iron Oxide nanoparticles (IONPs).Experiments were conducted to explore the effects of nanoparticle type and concentration, as well as ultrasound power, on transient heating up of the solutions exposed by 1 MHz ultrasound. Nanoparticles concentration was selected from 0.25 to 2.5 mg/ml and the solutions were exposed by ultrasound powers from 1 to 8 W. Real time temperature monitoring was done by a thermocouple and obtained data was analyzed.Temperature profiles of various nanoparticle solutions showed the higher heating rates, in comparison to water. Heating rise was strongly depended on nanoparticles concentration and ultrasound power. AuNPs showed a superior efficiency in heat generation enhancement in comparison to IONPs and NGO.Our result supports the idea of sonosensitizing capabilities of AuNPs, IONPs, and NGO. Targeted hyperthermia may be achievable by preferential loading of tumor with nanoparticles and subsequent ultrasound irradiation.     

Surface structure and morphology of InAs(1 1 1)B with/without gold nanoparticles annealed under arsenic or atomic hydrogen flux

We have investigated the structure and morphology of the InAs(1 1 1)B surface using Low Energy Electron Diffraction (LEED), Scanning Tunneling Microscopy (STM) and Scanning Electron Microscopy (SEM). The surface was prepared by annealing in the presence of an arsenic or atomic hydrogen pressure. A (2 × 2) reconstruction that changes into a (1 × 1) unreconstructed surface after prolonged annealing was observed irrespective of preparation method, while the surface morphology was distinctly different in the two cases. Detailed atomic scale models are proposed to explain the behavior. Deposition of Au aerosol nanoparticles on the sample prior to annealing was found to have no effect on the surface reconstruction. The Au particles were found to sink into the surface.     

Preparation and characterization of hybrid nanoparticles based on chitosan and poly(methacryloylglycylglycine)

CeO₂–MnO _x composites possessing rod-like morphology (fixed mole proportion of Ce/Mn) were synthesized through hydrothermal method and chosen as supporters to load PdO nanoparticles (PdO/Ce _x Mn_1–x ). The size of loaded PdO nanoparticles is about 2 nm. The catalytic behaviors of supported catalysts were examined through the complete catalytic oxidation of benzene. The results illustrated that the activities of supported catalysts were enhanced greatly as compared to unsupported, and the completely conversion temperature of benzene was reduced to ca. 250 °C. The effect of noble metal species (PdO) addition on the catalytic property and crystal structure of composites was researched in detail. The data revealed that the interaction between PdO and supporter, and intrinsic properties of supporter resulted in the enhancement of catalytic abilities.     

Preparation and electrophoretic response of poly(methyl methacrylate-co-methacrylic acid) coated TiO2 nanoparticles for electronic paper application

Titanium dioxide (TiO₂) nanoparticles were encapsulated with poly(methyl methacrylate-co-methacrylic acid) (PMMA-co-MAA) via simple method of coacervation, in order to improve the dispersion stability of the nanoparticles in a dielectric medium and to reduce the density mismatch between TiO₂ and a dielectric medium for a electrophoretic display application. The morphology of PMMA-co-MAA coated TiO₂ nanoparticles were observed via SEM and electrophoretic light scattering (ELS). It was found that density of PMMA coated TiO₂ nanoparticles were reduced by coating process via gas pycnometer. Electrophoretic mobility of the fabricated nanoparticles in a low dielectric medium with charge control agent was measured via electrophoretic light scattering spectrophotometer for potential application in electronic paper technology.     

Crystallizaion and surface morphology of poly(vinylidene fluoride)/poly(methylmethacrylate) films by solution casting on different substrates

The dependence of surface structure of the poly(vinylidene fluoride) (PVDF)/poly(methylmethacrylate) (PMMA) films by solution casting on properties of seven substrates was investigated by wide angle X-ray diffraction (WAXD), Fourier transform infrared (FTIR), scanning electron microscope (SEM) and differential scanning calorimetry (DSC). It was revealed that the polyblend films obtained by casting onto each substrate contained exclusively β phase PVDF. Higher crystallinity of the film was obtained by casting onto ceramic, polytetrafluoroethylene (PTFE), copper (Cu), stainless steel and glass substrates than that by casting onto aluminium (Al) and polypropylene (PP) substrates, depending on the degree of close lattice matching. The surface crystalline structure of PVDF was strongly affected by the wettability of substrate. The largest size of PVDF spherulitic crystal structure with about 6 μm presented in the casting film grown at the air/solution interface on glass substrate, while the smallest spherulite size with about 3 μm was generated by casting onto PTFE, stainless steel and PP substrates. It implied that the higher surface tension the substrate had, the larger PVDF spherulite grew at the air/solution interface.     

Solution templating of Au and Ag nanoparticles by linear poly[2-(diethylamino)ethyl methacrylate]

Abstract  

Linear poly[2-(diethylamino)ethyl methacrylate], poly(DEAMA), is an uncommon example of a homopolymer that can reduce salts of Au and Ag in solution to yield stable dispersions of nanoparticles (5–25 nm typical size). Poly(DEAMA)-stabilized Au and Ag nanoparticles were prepared in a mixture of water and 2-butoxyethanol, an amphiphilic organic solvent. The “loading ratio” (mole ratio of metal atoms to amines), a key parameter influencing particle size and clustering, was systematically varied. The size distribution and clustering of the nanoparticles were characterized by transmission electron microscopy and small-angle X–ray scattering. The maximum loading ratio achievable without inducing precipitation was approximately 0.3 for Au, but the maximum loading ratio for Ag was only about 0.04. The preparation of both Au and Ag nanoparticles in solution with a linear polymeric template illustrates that dendritic or hyperbranched architecture of the polymer is not a prerequisite for obtaining stable, non-aggregated dispersions. From a practical standpoint, poly(DEAMA) is an inexpensive template material that is readily immobilized on silica, which could facilitate development of novel, nanoparticle-based heterogeneous catalysts.     

Ablation of poly(methyl methacrylate) and poly(2-hydroxyethyl methacrylate) by 308, 222 and 193 nm excimer-laser radiation

Data on the ablation of Poly(Methyl MetAcylate) (PMMA) and Poly(2-Hydroxyethyl MetAcylate) (PHEMA) with 0%, 1% and 20% of Ethylene Glycol DiMethAcrylate (EGDMA) as crosslinking monomer by 193, 222 and 308 nm laser radiation are presented. Direct photoetching of PMMA at 308 nm is demonstrated for laser fluences ranging from 2 to 18 J/cm². The ablation rate of PHEMA is lower than the corresponding to PMMA and decreases when the amount of EGDMA increases. The determination of the absorbed energy density required to initiate significant ablation suggests that the photoetching mechanism is similar for all the polymers studied and is a function of the irradiation wavelength. The Beer-Lambert law, the Srinivasan, Smrtic and Babu (SSB) theory and the kinetic model of the moving interface are used to analyze the experimental results. It is shown that only the moving interface theory fits well the etch rate for all the selected polymers at the three radiation wavelengths.