Thin Layer Chromatographic Screening of Coal Liquids

Abstract

Procedures are described for the thin layer chromatographic (TLC) analysis of coal-derived liquids. After solvent selection using Selectosol (1) radial TLC, a series of compounds typically found in coal liquids was used to demonstrate their elution behavior on silica gel. It was determined that unactivated (Brockman 4) silica plates series developed with isooctane/tetrahydrofuran (THF) (80:20, v/v) provided the best separation. The order of elution was saturate >hydroaromatic >polynuclear aromatic (PNA)>phenols ≥ nitrogen bases. The use of two-dimensional TLC with reverse phase and silica contiguous on the same plate (Whatman Multi-K) is discussed for the rapid separation and identification of coal liquid components. Trimethylsilyl ether derivatives were prepared of phenols and alcohols present in coal conversion products. This technique proved most useful in that the TMS-derivatives behaved similarly to their parent PNA, in order of elution, on silica plates using a moderately active mobile phase (isooctane: THF,80:20, v/v). TLC and the reactions described provide a semi-quantitative measure of the degree of hydrogenation of coal-derived liquids.     

Application of Waste Liquids Containing Lignin from Pulp-producing Industry to CWM Preparation

IntroductionSince the first oil crisis in1 973,coal conver-sion technologies such as coal gasification,lique-faction and combustion have been studied in orderto use coal as an alternative resource of oil.In thiscontext,coal water mixtures( CWMs) are attrac-tive because they are more transportable andstorable than non- treated coal for being used as analternative resource of oil.To prepare CWMs witha higher energy density,the coal concentrationshould be high in CWMs.However,high coal con-ce…     

Limitations of mass spectrometric methods for the characterization of polydisperse materials

This paper is a review of work on the characterization of coal liquids and petroleum residues and asphaltenes over several decades in which various mass spectrometric methods have been investigated. The limitations of mass spectrometric methods require exploration in order to understand what the different analytical methods can reveal about environmental pollution by these kinds of samples and, perhaps more importantly, what they cannot reveal. The application of mass spectrometry to environmental problems generally requires the detection and determination of the concentration of specific pollutants released into the environment by accident or design. The release of crude petroleum or coal liquids into the environment can be detected and tracked during biodegradation processes through specific chemicals such as alkanes or polyaromatic hydrocarbons (PAHs). However, petroleum asphaltenes are polydisperse materials of unknown mass range and chemical structures and, therefore, there are no individual chemicals to detect. It is necessary to determine methods of detection and the ranges of mass of such materials. This can only be achieved through fractionation to reduce the polydispersity of the initial sample. Comparison of mass spectrometric results with results from an independent analytical method such as size‐exclusion chromatography with a suitable eluent is advisable to confirm that all the sample has been detected and mass discrimination effects avoided. Copyright © 2010 John Wiley & Sons, Ltd.     

Liquid Chromatography with Room Temperature Ionic Liquids

JPC – Journal of Planar Chromatography – Modern TLC - Room temperature ionic liquids are a new class of solvents of potential interest for liquid chromatography. Ionic liquids possess a...     

14 MeV INAA nitrogen determination in coal conversion liquids

Fast neutron activation analysis has been used for the direct determination of nitrogen in coal conversion liquids. In our previous work on coals, solid standards such as N-1-naphthylacetamide. NBS SRM 912 urea and NBS SRM 148 nicotinic acid were used for nitrogen determinations. In this work, a set of organic liquids was selected and evaluated for use as nitrogen standards in the analysis of coal-derived liquids. The use of the liquid standards minimizes problems associated with maintaining uniform irradiation and counting geometries and self absorption differences related to varying matrix densities. The standard liquids were selected using criteria of high boiling point, well-defined stoichiometry, high-purity, non-hygroscopic nature and simple C−H−N elemental compositions. Excellent agreement between the 14 MeV INAA data and calculated stoichiometric values has been demonstrated for liquids with nitrogen contents from 1.89 to 39.95%. The liquid standards have been used to determine nitrogen in a set of typical coal conversion liquids and several international standards.     

Planar Dielectrochromatography on Non-Wetted Thin Layers

JPC – Journal of Planar Chromatography – Modern TLC - Some of the physical properties of dielectric liquids are influenced by electric fields. Interesting results were obtained in this...     

Reduction of silanophilic interactions in liquid chromatography with the use of ionic liquids

A suppression of silanophilic interactions by the selected ionic liquids added to the mobile phase in thin-layer chromatography (TLC) and high-performance liquid chromatography (HPLC) is reported. Acetonitrile was used as the eluent, alone or with various concentrations of water and phosphoric buffer pH 3. Selectivity of the normal (NP) and the reversed (RP) stationary phase material was examined using a series of proton-acceptor basic drugs analytes. The ionic liquids studied appeared to significantly affect analyte retention in NP-TLC, RP-TLC and RP-HPLC systems tested. Consequently, the increased separation selectivity was attained. Due to ionic liquid additives to eluent even analytes could be chromatographed, which were not eluted from the silica-based stationary phase materials with 100% of acetonitrile in the mobile phase. Addition of ionic liquid already in very small concentration (0.5%, v/v) could reduce the amount of acetonitrile used during the optimization of basic analytes separations in TLC and HPLC systems. Moreover, the influence of temperature on the separation of basic analytes was demonstrated and considered in practical HPLC method development.     

A Comparison of Polymer Separation Efficiency and Resolution by Gradient LC,GPC and TLC

Abstract

The specific resolution of gradient LC and reversed phase TLC methods for the separation of different molecular weight standards of poly(isoprene), poly(ethylene glycol), poly(ethylene oxide), poly(styrene) and poly(α-methylstyrene) were determined. It was found that gradient LC has an order of magnitude greater resolving power (for high polymers) than gel permeation chromatography (GPC) while TLC had from two to five times the resolving power of GPC in the molecular weight range investigated. This is a direct result of the greater selectivity of gradient LC and TLC techniques. The specific resolution is also dependent on the type of gradient used to achieve fractionation for the LC technique.     

Impregnated silica-based layers in thin layer chromatography

Abstract

Impregnated thin-layer chromatography (TLC) layers based on silica gel are presented. Impregnating agents such as metal cations, inorganic ions, chelating agents, chiral selectors, surfactants, ion-pairing reagents, and ionic liquids are discussed. The role of impregnated TLC layers in medicinal chemistry is highlighted. The historical overview of TLC separations on physically coated layers is given and some future prospects ahead of this technique are discussed.     

Thin-layer chromatography in the analysis of surfactants: At a glance

This review presents the research work appeared in the literature during 1983–2016 on identification, separation, and determination of surfactants using different modes of thin-layer chromatography (TLC), e.g., normal phase TLC (NP-TLC), high-performance TLC (HP-TLC), and reversed-phase TLC (RP-TLC). The relative work done on these techniques follows the trend: NP-TLC?>?HP-TLC?>?RP-TLC. Most of the work performed has been concentrated on the analysis of nonionic surfactants compared to the other types of surfactants. The analysis trend of surfactants by TLC follows the order: nonionic?>?cationic?>?anionic?>?amphoteric. Green solvents as an eluant in TLC analysis of surfactants have been recently introduced. In addition, the entry of ionic liquids (ILs) as a mobile phase or as an impregnant of stationary phase tremendously increased the scope of TLC as green chromatographic technique in the analysis of surfactants. The advantageous features of ILs including negligible vapor pressure, good thermal stability, tunable viscosity, nonflammable, and miscibility with water and organic solvents as well as good extractability for various organic compounds and metal ions have expanded the scope of TLC in chemical analysis.     

Chemical changes of organic compounds in chlorinated water. XI. Thin-layer chromatographic fractionation of Ames mutagenic compounds in chlorine-treated 4-methylphenol solution

The diethyl ether extract from an aqueous solution of 4-methylphenol after treatment with hypochlorite was mutagenic to the Ames Salmonella test strain TA100 in the absence of liver homogenate. Gas chromatography-mass spectrometry (GC-MS) showed the occurrence of, at least, twenty compounds in the extract: chloro-4-methylphenols, chlorohydroxy-4-methylquinones and chlorinated 4-methylphenol dimers. The diethyl ether extract was fractionated into several fractions by silica gel and polyamide thin-layer chromatography (TLC). The fractionated components were then examined for mutagenicity by means of Ames assays, and were identified by GC-MS. TLC fractionation of the extract revealed that the major components present in the extract are not mutagenic, but minor components (less than 4% of the total extract) are mutagenic. GC-MS analysis indicated the presence of chlorinated 4-methylphenol dimers in the fraction which exhibited the highest mutagenicity.     

Use of combined chromatographic methods including thin-layer chromatography for analysis of complex polymer systems. Determination of the polydispersity of block copolymers of styrene and methyl methacrylate by gel permeation, thin-layer and pyrolysis gas chromatography.

A combination of gel permeation chromatography (GPC), thin-layer chromatography (TLC) and pyrolysis gas chromatography (PGC) has been used for investigations of a polymethyl methacrylate-polystyrene-polymethyl methacrylate block copolymer. Continuous distribution of the polymer (40-mg sample) was attained according to the content of the styrene and methyl methacrylate units and of the block copolymer and according to the composition of the copolymer as functions of the hydrodynamic radius of the macromolecules. The polymer was subjected to a preliminary fractionation with an analytical gel chromatograph. The fractions were investigated by TLC, which permitted the separation of the block copolymer and the homopolymers. The composition of the fractions obtained by GPC and TLC was determined by PGC. As a result, it was possible to establish the composition of the block copolymer and its ratio to polymethyl methacrylate in each fraction. This investigation was based on a combination of highly effective fractionation by chromatographic methods with precise quantitative ratios obtained from Benoit's universal calibration graph and from determinations of the composition of the polymer fractions by PGC. The mechanism of the TLC of polymers, including the appearance of artefacts that distort the results of analysis, is also discussed.     

The extraction of coal with supercritical hydrocarbon mixtures

The National Coal Board has developed a process for converting coal into distillable liquids based on the extraction by supercritical fluids of fragments of coal molecules produced by thermolysis. The resultant coal extract has desirable properties for subsequent hydroprocessing. This paper outlines process requirements and describes how these were realised in a 10 kg h⁻¹ pilot plant. Results illustrating the effects of main process variables are given, using examples taken from experimental work employing a simulated process-derived solvent as extractant. Yields and analyses are presented for products obtained under varied processing conditions.     

Behavior of peptides and computer-assisted optimization of peptides separations in a normal-phase thin-layer chromatography system with and without the addition of ionic liquid in the eluent

The addition of an ionic liquid into the mobile phase appeared to be useful in optimization of chromatographic separation of peptides. Different behavior of peptides in thin-layer chromatography (TLC) was observed after addition of 1-ethyl-3-methylimidazolium tetra fluoroborate to the eluent in comparison to the system without the ionic liquid. Nonlinear dependence of the retention coefficient, R(M), of peptides on the volume percentage of acetonitrile in the eluent was found in normal-phase TLC with and without immidazolium tetra fluoroborate in the mobile phase. In general, R(M) increased with increasing concentration of acetonitrile. In TLC systems without the ionic liquid, R(M) can be described well with a quadratic function. On the other hand, in a TLC system with an ionic liquid as the additive to the mobile phase, the retention behavior is better described with a third-degree polynomial function. The potential usefulness of ionic liquids for optimization of separation of peptides was demonstrated. Optimization of the separation conditions was supported by a commercially available computer program.     

Use of basic alumina in fractionation of fossil fuels

The use and efficiency of extrographic fractionation are reported for a number of fossil fuels and their processing products. The influence of basic alumina, which is a constituent of the column packing, on the fractionation selectivity is discussed. This fractionation is capable of an efficient separation of non-polar hydrocarbons, pyrrolic-type nitrogen compounds, and phenolic compounds. The hydrocarbon fraction also includes highly condensed polyaromatics. In the chromatographic fractionation these polyaromatics are eluted along with heteroatom-rich compounds. The extrographic fractionation has been found to be independent of column loading on going from a sample-to-sorbent ratio of 1:15 to 1:8 (w/w). However, it is not possible to separate aromatic hydrocarbons according to the ring number, and therefore the extrography is a suitable method for the fractionation of coal-derived liquids containing large amounts of heteroatom compounds of different polarity.     

Application of thin-layer chromatography with fluorescence scanning densitometry for analysing saturates in heavy liquids derived from Co-pyrolysis of biomass and plastics

Summary Two alternative methods, based on Thin-Layer Chromatography (TLC) with Fluorescence Scanning Densitometry have been developed for characterization of heavy liquids from copyrolysis of different kinds of biomass and plastics in autoclaves under inert atmosphere. A conventional TLC system, which includes a vertical developing tank, and a High Performance TLC (HPTLC) system, with a horizontal developing chamber and the use of HPTLC plates, have been used. The analytical method involves in both cases the measurement of two chromatograms per sample: the first, on a silica gel berberine-impregnated plate, for detection of saturates using the phenomenon of berberine-induced fluorescence; and the second, on a silica gel plate, for detection of aromatic-polars and polars, by native fluorescence. Although the HPTLC system is more sensitive and faster, both techniques represent an improvement with regard to current methods for analyzing these kinds of products. However their application depends on the particular solubility of each sample and on its slope of the fluorescent response-sample load regression.     

The stereochemistry of heterocycles

Fifteen previously unreported 2-alkyl- and 5-alkyl-2, 2-dimethyl-1, 3-dithianes have been synthesized by the condensation of 2-alkylpropane-1, 3-dithiols with acetaldehyde, isobutylraldehyde, and acetone, and their structures have been confirmed by their IR spectra. The existence of stereoisomers in a number of the thioacetals has been shown by GLC and TLC. Some of the stereoisomeric 2, 5-diakyl-1, 3-dithianes have been separated by fractionation in an efficient column into the individual isomers, the purity of which was confirmed by TLC, GLC, and IR spectroscopy.For part III, see [11].     

Experimental study on the separation of silica gel supports by gravitational field-flow fractionation

The separation and characterization of silica gel particles were investigated by gravitational (1 g) field-flow fractionation. The experiments were performed in a ribbon-like glass-walled channel with a photometric (turbidimetric) detector. Solutions of several surfactants were tested as carrier liquids. Factors affecting the separation process are discussed and the deductions are compared with experimental results. Some aspects concerning the activity of lift forces were confirmed.     

抚顺烟煤及其抽出物的FTIR光谱结构表征

用富立叶变换红外光谱(FTIR)对抚顺烟煤的有机组分进行了测定。通过对谱图的解析,指出抚顺烟煤及其吡啶抽出物和抽提残煤在结构上的异同。以及抽出物各色谱馏分中存在的官能团和官能团之间极性的差异,对原煤整体结构提供了精细的结构信息。     

Some new features of Direct Analysis in Real Time mass spectrometry utilizing the desorption at an angle option

The present study is a first step towards the unexplored capabilities of Direct Analysis in Real Time (DART) mass spectrometry (MS) arising from the possibility of the desorption at an angle: scanning analysis of surfaces, including the coupling of thin‐layer chromatography (TLC) with DART‐MS, and a more sensitive analysis due to the preliminary concentration of analytes dissolved in large volumes of liquids on glass surfaces. In order to select the most favorable conditions for DART‐MS analysis, proper positioning of samples is important. Therefore, a simple and cheap technique for the visualization of the impact region of the DART gas stream onto a substrate was developed. A filter paper or TLC plate, previously loaded with the analyte, was immersed in a derivatization solution. On this substrate, owing to the impact of the hot DART gas, reaction of the analyte to a colored product occurred. An improved capability of detection of DART‐MS for the analysis of liquids was demonstrated by applying large volumes of model solutions of coumaphos into small glass vessels and drying these solutions prior to DART‐MS analysis under ambient conditions. This allowed the introduction of, by up to more than two orders of magnitude, increased quantities of analyte compared with the conventional DART‐MS analysis of liquids. Through this improved detectability, the capabilities of DART‐MS in trace analysis could be strengthened. Copyright © 2011 John Wiley & Sons, Ltd.