高温热处理对偏氟乙烯-四氟乙烯共聚物高次结构的影响

聚偏氟乙烯(PVDF)及其一些共聚物,例如偏氟乙烯-四氟乙烯共聚物(PVDF/TFE)经过处理后呈现较强的压电性。许多研究表明它们是铁电聚合物,而且压电活性与样品的高次结构有关。松弛谱是研究结晶高聚物的高次结构的有力工具,近来,Koizumi等人报道了PVDF/TFE的热处理与松弛现象的关系。本文作者也报道了     

四氟乙烯/偏氟乙烯乳液共聚反应的竞聚率测定

用亨利定律关联了四氟乙烯 (TFE) /偏氟乙烯 (VDF)乳液共聚合体系中的单体气相分压与其对应液相浓度间的关系 ,推导了用气相摩尔分数表示的共聚物组成方程式 .通过气相色谱和19F NMR分别测定了共聚反应前后气相单体组成和共聚物组成 ,用非线性回归法 (RREVM )计算TFE/VDF乳液共聚合反应表观竞聚率分别为γTFE=0 35和γVDF=0 6 3 .将实测的表观竞聚率代入共聚物组成方程计算共聚物组成与由19F NMR测定的结果一致 ,为进一步的工业放大试验提供科学依据     

高温热处理对偏氟乙烯-四氟乙烯共聚物高次结构的影响

The effect of high temperature annealing on the higher order structure of a copolymer of vinylidene fluoride and tetrafluoroethylene (TFE 2.8 mol %) has been studied by various method, primarily dynamic mechanical, by also dielectric and microspic. The controversy on the origin of a relaxations is discussed from the point of view of higher order structure studies.     

偏氟乙烯-四氟乙烯共聚物的β、γ混合晶型固相转变与松弛现象

本文用红外光谱及压电常数方法研究了偏氟乙烯-四氟乙烯共聚物在高压直流电场下,γ晶型向β晶型的固相转变。同时用动态力学方法、介电损耗测试法及压电常数方法研究了样品的松弛现象。     

偏氟乙烯和四氟乙烯共聚反应中链自由基的反应性

应用高分辨率核磁共振仪研究了一系列不同组成的偏氟乙烯和四氟乙烯共聚物。指出,共振核—CF_2—的化学位移不仅受第一、二邻位基团的影响,也受第三邻位的影响。偏氟乙烯和四氟乙烯以无规共聚进行反应,在共聚反应中的链自由基﹏CF_2·或﹏CH_2·容易增长于CH_2=CF_2的CH_2端,而链自由基﹏CH_2·在偏氟乙烯和四氟乙烯共聚反应中的增长倾向于四氟乙烯。     

偏氟乙烯-三氟乙烯共聚物的分子链结构与多晶型现象

偏氟乙烯-三氟乙烯共聚物(PVDF/TrFE)的合成及物性研究,是改善聚偏氟乙烯(PVDF)压电性的一种尝试。据文献报道,PVDF/TrFE 有明显的铁电性,以及强的压电性     

偏氟乙烯／三氟乙烯共聚物介电松弛的结晶度效应

用改进的介电松弛谱仪（精度２‰）测定了ＶＤＦ／ＴｒＦＥ（７／２７、６５／３５、５２／４８ｍｏｌ％）共聚物溶液成膜、液氮淬火、熔融慢冷和热处理试样在－１２０—１３０℃、１０－２一１０４Ｈｚ范围的复数介电常数．介电松弛研究结果显示低结晶度的淬火试样较高结晶度的熔融慢冷和热处理试样的Ｔｃ高．结晶度上升，居里点处的介电常数增大．室温以下的介电频率谱分别由代表非晶区分子运动的β松弛（低频部）和局域运动的γ松弛（高频部）叠合而成．随结晶度提高，β松弛峰减小，γ松弛峰增大；非晶松弛强度减弱．晶区松弛强度增强．     

钛酸铅与偏氟乙烯-三氟乙烯共聚物形成的铁电复合物相变过程的热释电研究

研究了偏氟乙烯-三氟乙烯共聚物与钛酸铅形成的铁电复合物PT/P[VDF(70)-TrFE(30)]的热释电流行为。P[VDF(70)-TrFE(30)]室温下存在两个铁电相,即较无序的铁电相和较有序的铁电相,升温经过各自的相转变点后转变成较有序的顺电相和较无序的顺电相。热释电流谱上出现在95℃和108℃的两个电流峰,分别由两个铁电相的结构陷阱以及部分取向的偶极所贡献。采用Tc以上温度极化并冷却到不同温度的方法可明确鉴别出该试样两个顺电相降温转变过程,转变点分别为62℃和50℃。实验证实陷阱仅存在于铁电相而不存在于顺电相中。钛酸铅的引入虽不导致新电流峰出现,但可使共聚物的Tc降低、电流加大。热释电流方法可非常灵敏地跟踪铁电共聚物的相变过程。     

非晶态与晶态的压电热电铁电高聚物

本文综述了晶态与非晶态两类高聚物的压电性,热释电性和铁电性。这些现象近年来研究得愈来愈广泛。文中以聚氯乙烯作为非晶态高聚物的例子;以PVDF及其共聚物,还有尼龙11作为晶态高聚物的例子。按照偶极子模型,高聚物一般假定需具备四个条件,就可显示出较大的压电性,热释电性和铁电性。本文探讨了上述高聚物的结构与性能,这些对识别材料是很重要的。最后,列举了PVDF及其它材料的压电常数,热释电系数和介电常数,以供读者参考。     

Symmetric Ferroelectric Switching in Ferroelectric Vinylidene Fluoride and Trifluoroethylene Copolymer Films

We report the observation of asymmetric switching dual peaks in ferroelectric copolymer films. These dual peaks occurs when the poling electric field is just below the coercive field and can be removed by continuous application of high enough switching voltage. Our experimental observations can be explained by the injection and the redistribution of space charges in ferroelectric films.     

偏氟乙烯分散聚合的成核及初级粒径

以分散聚合的相关成核理论为基础,采用核磁共振（19F-NMR）和傅里叶红外分析（FT-IR）等分析方法研究了偏氟乙烯（VDF）分散聚合的成核机理,并确认了以低聚物成核机理为其主要形式。同时,通过实验确定了PVDF乳胶粒粒径（d）与转化率（X）、反应压力（p）、初始引发剂质量浓度（ρI,0）以及初始乳化剂质量浓度（ρS,0）有着如下关系：d∝X0.36 p1.20ρI-,00.76ρS-,00.33。在各个因素中,反应压力（或单体质量浓度）的影响程度最大。     

Unexpected Radical Telomerisation of Vinylidene Fluoride with 2-Mercaptoethanol

The radical telomerisation of vinylidene fluoride (VDF) with 2-mercaptoethanol as chain transfer agent (CTA) was studied to synthesise fluorinated telomers which bear a hydroxy end-group, such as H(VDF)_nS(CH₂)₂OH, under thermal (di-tert-butyl peroxide as the initiator) or photochemical initiations. A careful structural study of a typical H-VDF-S(CH₂)₂OH telomer was performed by ¹H and ¹⁹F NMR spectroscopy. These analytical methods allowed us to explore the selective addition of the thiyl radical onto the hydrogenated side of VDF, and the telomer containing one VDF unit was obtained selectively. Surprisingly, for higher [VDF]_o initial concentrations, a monoadduct telomer was produced as well as PVDF homopolymer. This feature was related to the fast consumption of the CTA. The kinetics of radical telomerisation led to a quite high transfer constant of the CTA (40 at 140 °C) that evidences the formation of a monoadduct as the only telomer formed.     

Homogeneous Phase Copolymerizations of Vinylidene Fluoride and Hexafluoropropene in Supercritical Carbon Dioxide

Copolymerizations of vinylidene fluoride (VDF) and hexafluoropropene (HFP) were carried out in homogeneous phase with supercritical carbon dioxide up to complete VDF conversion using conventional peroxide initiators. The HFP monomer feed ratios, f_HFP, were varied between 0.65 and 0.20. Depending on f_HFP amorphous or semi‐crystalline copolymers were obtained. f_HFP also determines the minimum pressure required to allow for homogeneous phase reactions. For example, HFP‐rich copolymerizations in 70 wt.‐% CO₂ at 100 °C require a pressure of around 500 bar. Further, bulk copolymerizations in homogenous phase were feasible for f_HFP = 0.65 at 900 bar up to complete VDF conversion. Copolymerizations in the presence of perfluorinated hexyl iodide carried out at 75 °C gave access to low dispersity polymers. Due to homogeneous phase conditions the use of any surfactants or fluorinated cosolvent is avoided.

     

Organometallic‐Mediated Radical Polymerization of Vinylidene Fluoride

An unprecedented level of control for the radical polymerization of vinylidene fluoride (VDF), yielding well‐defined PVDF (at least up to 14 500 g mol^?1) with low dispersity (≤1.32), was achieved using organometallic‐mediated radical polymerization (OMRP) with an organocobalt compound as initiator. The high chain‐end fidelity was demonstrated by the synthesis of PVDF‐ and PVAc‐containing di‐and triblock copolymers. DFT calculations rationalize the efficient reactivation of both head and tail chain end dormant species.     

合成偏氟乙烯和含氟丙烯的催化剂及应用研究进展

由于含氟烯烃在自然界易降解、对臭氧层破坏力小、对环境友好的特性,近年来在科研和工业领域得到广泛关注.偏氟乙烯（VDF）和含氟丙烯是重要的含氟烯烃,主要用于合成氟弹性体高分子功能材料的单体和含氟树脂等.我们参照偏氟乙烯的合成发展史,主要介绍了通过催化,热裂解和共裂解方法合成偏氟乙烯过程中使用的催化剂类型、工艺条件和结果对比,综述了近年来偏氟乙烯的主要合成方法,并介绍了通过直接催化氟化法合成含氟丙烯的工艺技术及其可能机理研究进展.     

Crystal‐structure dependence of electroactive properties in differently prepared poly(vinylidene fluoride/hexafluoropropylene) copolymer films

The electroactive properties of two random copolymers of vinylidene fluoride (VDF) and hexafluoropropylene (HFP) were studied. The compositions were 95/5 and 85/15 mol % P(VDF/HFP). For each composition, three different film‐preparation methods were used—solvent casting, melt‐pressed quenched, and melt‐pressed slow‐cooled. The ferroelectric properties observed were strongly dependent on the preparation methods of the films as well as the HFP molar content of the samples. The highest remanent polarizations (P_r) obtained from electric displacement versus electric field (D‐E) hysteresis data are 80 and 50 mC/m² for the 5 and 15% HFP solvent‐cast samples, respectively. The slow‐cooled samples do not exhibit any ferroelectric behavior for either the 5 or 15% HFP copolymers. It was also observed that both the 5 and 15% HFP slow‐cooled samples have a smaller electrostrictive response relative to the other two types of samples. Wide‐angle X‐ray diffraction and DSC results suggest that the 5% HFP sample has a higher crystallinity relative to the 15% HFP sample for each preparation method. In addition, different crystal phases form in the samples resulting from the different preparation methods. Fourier transform infrared results suggest that the slow‐cooled samples are in the nonpolar α phase, whereas the quenched and solvent‐cast samples are more likely in the polar β phase. The slow‐cooled samples do not show a switching peak in their nonpolar α‐phase crystalline state. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2793–2799, 2001     

Homogeneous Phase Polymerization of Vinylidene Fluoride in Supercritical CO2: Surfactant Free Synthesis and Kinetics

Summary: Vinylidene fluoride (VDF) polymerizations were carried out in homogeneous phase with supercritical carbon dioxide (scCO₂) at 120 °C and 1500 bar. To control molecular weight perfluorohexyl iodide was used. Molecular weight analysis by size-exclusion chromatography indicates that polymers of low polydispersities ranging from 1.5 to 1.2 at the highest iodide concentration of 0.25 mol · L⁻¹ were obtained. In addition, polymer molecular weight increases linearly with reaction time, indicating that living conditions were established. The “livingness” is based on the labile C-I bond. The weakness of the C-I bond is associated with a fast decomposition of the original hexyl iodide, thus, contributing to initiation and to a significant increase in the initiation rate in the initial phase of the polymerization.