Sorbitol and gluconic acid production using permeabilized Zymomonas mobilis cells confined by hollow-fiber membranes

Immobilization of Zymomonas mobilis by different methods was investigated. Experiments were performed order to choose the most appropriate support for the immobilization of the cells. The most advantageous option was to use permeabilized cells in the bore of microporous hollow fibers. Whereas the reaction rate was about 33 g of gluconate/ (g of protein·h) using hollow fibers, which is comparable to that observed by using free cells, the calcium alginate immobilized cells presented a reaction rate of 4 g of gluconate/ (g of protein·h). These results can be explained by the mass transfer resistance effect, which, indeed, was much lower in the case of hollow-fiber membranes than in the alginate gel beads. A loss of enzymatic activity during the reaction was observed in all experiments, which was attributed to the lactone produced as an intermediate of the reaction.     

Oxidized single-walled carbon nanohorns as sorbent for porous hollow fiber direct immersion solid-phase microextraction for the determination of triazines in waters

This paper evaluates the potential of oxidized single-walled carbon nanohorns (o-SWNHs) immobilized on the pores of a hollow fiber (HF) for the direct immersion solid-phase microextraction of triazines from waters. The fabrication of the device requires the oxidation of the nanoparticles by means of microwave irradiation in order to obtain a homogeneous dispersion in methanol. Then, a porous hollow fiber is immersed in the methanolic dispersion of the o-SWNHs under ultrasound stirring. This procedure permits the immobilization of the o-SWNHs in the pores of the hollow fiber. For the extraction, a stainless steel wire was introduced inside the fiber to allow the vertical immersion of the o-SWNHs-HF in the aqueous standard/water sample. The triazines were preconcentrated on the immobilized o-SWNHs and further eluted using 150 μL of methanol. The solvent was evaporated and the residue reconstituted in 10 μL of methanol for sensitivity enhancement. Gas chromatography–mass spectrometry was selected as instrumental technique. The limits of detection were between 0.05 and 0.1 μg?L^?1 with an excellent precision (expressed as relative standard deviation) between runs (below 10.2 %) and between fibers (below 12.8 %). Finally, the method was applied to the determination of the triazines in fortified waters, an average recovery value of 90 % being obtained.     

Characterization of wood fibers modified by phenol-formaldehyde

Wood-fiber phenol-formaldehyde-resin (PFR) modified surfaces, obtained from the adsorption of a PFR/water solution, are investigated as a function of the nature and the amount of PFR adsorbed. Surface are measurements are performed by using krypton adsorption at 77 K. Chemical modification is monitored by the electron spectroscopy for chemical analysis (ESCA) technique and the surface energy by the inverse phase gas chromatography (IPGC) method at infinite dilution. The London dispersive componentγ _S ^L of the surface energy shows a relationship to the concentration of carbon and oxgen at the fiber surface.γ _S ^L increases from 27.5 mN·m⁻¹ for the untreated fiber to 42.5 mN·m⁻¹ for the fibers treated with 20% high molecular-weight-grade phenol-formaldehyde. The surface atomic ratio O/C determined using the ESCA technique exhibits a decrease from 44% for untreated to 31% for treated samples. Surface area also decreases from 2.09 m²/g to 1.50 m²/g. The PFR adsorbed by wood fibers is observed as the dispersive component of surface energy starts to increase, as the surface oxygen concentration decreases, and on the surface area of the wood fiber.     

Extraction and preconcentration of tylosin from milk samples through functionalized TiO2 nanoparticles reinforced with a hollow fiber membrane as a novel solid/liquid‐phase microextraction technique

The aim of this study was to introduce a novel, simple, and highly sensitive preparation method for determination of tylosin in different milk samples. In the so‐called functionalized TiO₂ hollow fiber solid/liquid‐phase microextraction method, the acceptor phase is functionalized TiO₂ nanoparticles that are dispersed in the organic solvent and held in the pores and lumen of a porous polypropylene hollow fiber membrane. An effective functionalization of TiO₂ nanoparticles has been done in the presence of aqueous H₂O₂ and a mild acidic ambient under UV irradiation. This novel extraction method showed excellent extraction efficiency and a high enrichment factor (540.2) in comparison with conventional hollow fiber liquid‐phase microextraction. All the experiments were monitored at λ_max = 284 nm using a simple double beam UV‐visible spectrophotometer. A Taguchi orthogonal array experimental design with an OA₁₆ (4⁵) matrix was employed to optimize the factors affecting the efficiency of hollow fiber solid/liquid‐phase microextraction such as pH, stirring rate, salt addition, extraction time, and the volume of donor phase. This developed method was successfully applied for the separation and determination of tylosin in milk samples with a linear concentration range of 0.51–7000 μg/L (r² = 0.991) and 0.21 μg/L as the limit of detection.     

Carrier-mediated hollow fiber liquid-phase microextraction for preconcentration followed by spectrophotometric determination of amoxicillin

Preconcentration followed by ultraviolet spectrophotometric determination of amoxicillin (Amox) in pharmaceuticals and water samples by using a three-phase hollow fiber microextraction technique based on carrier-mediated transport has been presented. Amox was extracted from an aqueous solution (source phase) at pH 9.0 into 1-octanol containing 5% (w/v) Aliquat-336 impregnated in the pores of a hollow fiber. It was then back-extracted into NaCl solution (pH = 4.0) which was already positioned as the receiving phase inside the lumen of the hollow fiber. The extraction took place due to the concentration gradient of the counterion between the source and the receiving phases. Under the optimized conditions, an enrichment factor of 240 and a limit of detection of 0.2 μmol L⁻¹ were obtained. The calibration curve was linear (R² = 0.9967) in the concentration range of 0.5–10.0 µmol L⁻¹ Amox. The interday relative standard deviation (n = 9) and the intraday relative standard deviation (n = 3) for 1.0 × 10⁻⁶ mol L⁻¹ Amox solution were 7.3 and 6.4%, respectively.

     

Downstream processing of lactic acid-whey permeate fermentation broths by hollow fiber ultrafiltration

Membrane filtration is a suitable method for cell harvesting and clarification of fermentation broths. Hollow fiber ultrafilters gave essentially 100% rejection ofL. bulgaricus cells from a whey permeate fermentation broth. A combination of low pressures and high velocity generally gave the best permeate flux. Fermentation media components (in this case, from the whey permeate) contributed significantly to fouling. Considering the pressure limitations of the current generation of asymmetric hollow fiber modules and the changes in physical properties of the fermentation broths, a cell concentration of 100–150 g/L could be obtained with the flux still relatively high (above 20LMH), although the chemical compatibility of the membrane module itself under long-term exposure to high acid conditions should be considered.     

Liquid‐phase microextraction based on two immiscible organic solvents followed by gas chromatography with mass spectrometry as an efficient method for the preconcentration and determination of cocaine,ketamine, and lidocaine in human urine samples

A new type of liquid‐phase microextraction based on two immiscible organic solvents was optimized and validated for the quantification of lidocaine, ketamine, and cocaine in human urine samples. A hollow‐fiber based microextraction technique followed by gas chromatography coupled with mass spectrometry detection was used to reduce matrix interferences and improve limits of detection. The analytes were extracted from aqueous sample with pH 11.0, into a thin layer of organic solvent (n‐dodecane) sustained in the pores of a hollow fiber, and then into a second organic acceptor (acetonitrile) located inside the lumen of the hollow fiber. With the application of optimized values, good linearity was obtained in the range of 1–500 μg/L for lidocaine and ketamine and 2–500 μg/L for cocaine with the determination coefficient values (r²) >0.9943. The preconcentration factors and limits of detection (S/N > 3) were 250–350 and 0.01–0.05 μg/L, respectively. Intra and interassay precision values were <7.3 and 9.3%, respectively. The method was successfully applied for the determination and quantification of target analytes in human urine samples.     

Evaluation of two membrane‐based microextraction techniques for the determination of endocrine disruptors in aqueous samples by HPLC with diode array detection

In this study, the viability of two membrane‐based microextraction techniques for the determination of endocrine disruptors by high‐performance liquid chromatography with diode array detection was evaluated: hollow fiber microporous membrane liquid–liquid extraction and hollow‐fiber‐supported dispersive liquid–liquid microextraction. The extraction efficiencies obtained for methylparaben, ethylparaben, bisphenol A, benzophenone, and 2‐ethylhexyl‐4‐methoxycinnamate from aqueous matrices obtained using both approaches were compared and showed that hollow fiber microporous membrane liquid–liquid extraction exhibited higher extraction efficiency for most of the compounds studied. Therefore, a detailed optimization of the extraction procedure was carried out with this technique. The optimization of the extraction conditions and liquid desorption were performed by univariate analysis. The optimal conditions for the method were supported liquid membrane with 1‐octanol for 10 s, sample pH 7, addition of 15% w/v of NaCl, extraction time of 30 min, and liquid desorption in 150 μL of acetonitrile/methanol (50:50 v/v) for 5 min. The linear correlation coefficients were higher than 0.9936. The limits of detection were 0.5–4.6 μg/L and the limits of quantification were 2–16 μg/L. The analyte relative recoveries were 67–116%, and the relative standard deviations were less than 15.5%.     

Simultaneous reactive extraction separation of amino acids from water with D2EHPA in hollow fiber contactors

Reactive extraction separation of binary amino acids from water using a microporous hollow fiber has been studied, in which the acidic extractant di(2-ethylhexyl)phosphoric acid (D2EHPA) was selected as an active carrier dissolved in kerosene. l-Phenylalanine (Phe) was extracted from an aqueous solution through the shell side of module to the organic phase through the lumen of fiber in the extraction module, in which l-Phe was then back-extracted to stripping phase in stripping module. Experiments were conducted as a function of the initial feed concentration of equimolar Phe and l-aspartic acid (l-Asp) (5 mol/m³), feed pH (3–5), the carrier concentration (0.1–0.5 mol/dm³), and stripping acidity (0.1–2 mol/dm³). The effect of process variables on the separation factor of Phe/Asp and the possible transport resistances including aqueous-layer diffusion, membrane diffusion, organic-layer, and interfacial chemical reaction were quantitatively studied and discussed. The high separation factor (β) of Phe/Asp was obtained to be 18.5 at feed pH 5 and 2 mol/dm³ of strip solution (HCl). The extraction and stripping processes appear to rely on pH dependence of the distribution coefficient of amino acids in reactive extraction system. The separation factor (β) was enhanced in hollow fiber membrane (HFM) process compared with conventional solvent process, which was a result of the counter transport of hydrogen ions.     

Hollow‐fiber‐supported liquid membrane microextraction of amlodipine and atorvastatin

A simple, environmentally friendly, and efficient method, based on hollow‐fiber‐supported liquid membrane microextraction, followed by high‐performance liquid chromatography has been developed for the extraction and determination of amlodipine (AML) and atorvastatin (ATO) in water and urine samples. The AML in two‐phase hollow‐fiber liquid microextraction is extracted from 24.0 mL of the aqueous sample into an organic phase with microliter volume located inside the pores and lumen of a polypropylene hollow fiber as acceptor phase, but the ATO in three‐phase hollow‐fiber liquid microextraction is extracted from aqueous donor phase to organic phase and then back‐extracted to the aqueous acceptor phase, which can be directly injected into the high‐performance liquid chromatograph for analysis. The preconcentration factors in a range of 34–135 were obtained under the optimum conditions. The calibration curves were linear (R² ≥ 0.990) in the concentration range of 2.0–200 μg/L for AML and 5.0–200 μg/L for ATO. The limits of detection for AML and ATO were 0.5 and 2.0 μg/L, respectively. Tap water and human urine samples were successfully analyzed for the existence of AML and ATO using the proposed methods.     

Production of acetic acid by immobilized whole cells ofClostridium thermoaceticum

Immobilized cells ofClostridium thermoaceticum for acetic acid production has been investigated. Using κ-carrageenan gel as the immobilization-matrix, high cell concentration within the gel could be achieved and thus lead to high volumetric acetic acid productivity. Batch experiments using 3% gel showed that cell concentration up to 65 g (dry cell weight)/L gel could be achieved. These dry weight cell concentrations in the gel through immobilization are typically 10–15 times greater than what can be obtained in free-cell fermentations. The specific growth rate and acetic acid formation rate were similar to those observed for the free cells. Continuous culture experiments using a feed medium containing 20 g/L of glucose were performed where the reactor contained 50% by volume of the carrageenan gel and the pH was controlled at 6.9. Different steady states were acheived at dilution rates ranging from 0.061 to 0.399 h^?1. Cells grew mainly near the surface of the gel and reached maximum concentration within the matrix of approximately 35 g/L. Dilution rates much greater than the maximum specific growth rate were obtained, which resulted in volumetric productivity up to 4.9 g/L-h. This value was significantly greater than that for the conventional continuous culture with free cells. Using a 40 g/L feed glucose concentration, steady states could be achieved between dilution rates of 0.12–0.4 h^?1. The maximum productivity further increased to 6.9 g/L-h at a dilution rate of 0.37 h^?1 and at an acetic acid concentration of 19 g/L. The cell concentration was 60 g (dry weight)/L gel at steady state.     

Ethanol Production Using Immobilized <Emphasis Type="Italic">Saccharomyces cerevisiae</Emphasis> in Lyophilized Cellulose Gel

A new lyophilization technique was used for immobilization of Saccharomyces cerevisiae cells in hydroxyethylcellulose (HEC) gels. The suitability of the lyophilized HEC gels to serve as immobilization matrices for the yeast cells was assessed by calculating the immobilization efficiency and the cell retention in three consecutive batches, each in duration of 72 h. Throughout the repeated batch fermentation, the immobilization efficiency was almost constant with an average value of 0.92 (12–216 h). The maximum value of cell retention was 0.24 g immobilized cells/g gel. Both parameters indicated that lyophilized gels are stable and capable of retaining the immobilized yeast cells. Showing the yeast cells propagation within the polymeric matrix, the scanning electron microscope images also confirmed that the lyophilization technique for immobilization of S. cerevisiae cells in the HEC gels was successful. The activity of the immobilized yeast cells was demonstrated by their capacity to convert glucose to ethanol. Ethanol yield of 0.40, 0.43 and 0.30 g ethanol/g glucose corresponding to 79%, 84% and 60% of the theoretical yield was attained in the first, second and third batches, respectively. The cell leakage was less than 10% of the average concentration of the immobilized cells.     

Hollow-fiber liquid-liquid-solid micro-extraction of lead in soft drinks and determination by graphite furnace atomic absorption spectrometry

A novel hollow-fiber liquid-liquid-solid micro-extraction technique based on simultaneous liquid-liquid micro-extraction and solid phase micro-extraction using a polypropylene microporous membrane has been developed. The applicability of the proposed procedure was evaluated by extraction of Pb(II) from aqueous solutions and soft drinks. The parameters affecting the extraction efficiency were optimized using multivariate methodology, and the analytical features were established. Under optimized conditions, Pb(II) was concentrated for 20 min on three microporous membrane hollow fibers of 6 mm of length each, placed into 20 mL of sample containing 60 μL of toluene and ammonium O,O-diethyl dithiophosphate. The fibers were introduced directly into the graphite furnace as a solid sample, and the analyte was thermally desorbed from the fiber and atomized using ruthenium as a permanent modifier. A detection limit of 7 ng L⁻¹ Pb was obtained for soft drink samples and good repeatability was found for all samples. The enrichment factor varied between 22 and 66, depending if only one or all three hollow fibers were used for the determination of lead. The results suggest that the proposed procedure represents a simple and low-cost micro-extraction alternative rendering adequate limits of quantification for the determination of Pb(II) in soft drink samples.     

The preparation and characterization of silver‐loading cellulose acetate hollow fiber membrane for water treatment

Silver‐loading asymmetric cellulose acetate (CA) hollow fiber membrane was spun via the dry jet‐wet spinning technique. The spinning solution was prepared by dissolving AgNO₃ and CA in N,N‐dimethylformamide (DMF). The silver ions were reduced in the spinning dope into silver nano‐particles. The morphology of the resulting hollow fibers was examined using a scanning electron microscope and the silver content in the fiber was measured using an inductively coupled plasma atomic emission spectrometer. The antibacterial activities were evaluated. These hollow fibers had a sponge‐like structure and dense inner and outer surfaces. At a 50 k magnification, the pore on the skin layer was not observable, while the nodule size was smaller than 10 nm. The residual silver content of as‐spun hollow fiber was about 60% of the original silver added in the polymer solution. After immersing in water bath for 180 days, the silver content in the bulk of the hollow fibers decreased to 60% and the silver content on the surface reduced to 10%, yet still showed antibacterial activity against Escherichia coli and Staphylococcus aureus. After permeating with water for 5 days, the silver content in the hollow fibers decreased, and did not show antibacterial activity against E. coli and S. aureus. Thus, silver content must be periodically replenished after permeation. The proper range of AgNO₃ in the spinning solution for CA hollow fiber should be about 100–1000 ppm. Copyright © 2005 John Wiley & Sons, Ltd.     

Trace determination of perchlorate using electromembrane extraction and capillary electrophoresis with capacitively coupled contactless conductivity detection

Electromembrane extraction (EME) and CE with capacitively coupled contactless conductivity detection (CE‐C⁴D) was applied to rapid and sensitive determination of perchlorate in drinking water and environmental samples. Porous polypropylene hollow fiber impregnated with 1‐heptanol acted as a supported liquid membrane (SLM) and perchlorate was transported and preconcentrated in the fiber lumen on application of electric field. High selectivity of perchlorate determination and its baseline separation from major inorganic anions was achieved in CE‐C⁴D using background electrolyte solution consisting of 7.5 mM L ‐histidine and 40 mM acetic acid at pH 4.1. The analytical method showed excellent parameters in terms of reproducibility; RSD values for migration times and peak areas at a spiked concentration of 15 μg/L of perchlorate (US EPA recommended limit for drinking water) were below 0.2 and 8.7%, respectively, in all examined water samples. Linear calibration curves were obtained for perchlorate in the concentration range 1–100 μg/L (r²≥0.999) with limits of detection at 1 μg/L for tap water and at 0.25–0.35 μg/L for environmental and bottled potable water samples. Recoveries at 15 μg/L of perchlorate were between 95.9 and 106.7% with minimum and maximum recovery values for snow and bottled potable water samples, respectively.     

Xylitol production from wood hydrolyzates by entrapped Debaryomyces hansenii and Candida guilliermondii cells

Debaryomyces hansenii cells were entrapped in Ca-alginate beads and used for producing xylitol from wood hydrolyzates. Batch experiments showed that bioconversion was severely hindered when Ca-alginate beads were hardened with Al³⁺ solutions. As an alternative to Al³⁺ hardening, the improvements in both mechanical stability of bioparticles and fermenting ability of the immobilized system derived from using increased concentrations of sodium alginate were assessed. The best results were obtained using a 4% (w/v) Na-alginate solution in the gelification step. This concentration was selected to perform continuous fermentations in a packed-bed reactor using raw or charcoal-treated hydrolyzates (15.5 g of xylose/L) with two different yeasts: Candida guilliermondii and Debaryomyces hansenii. With a final cell concentration of about 50 g of cells/L (0.075 g of cells/g of beads), the volumetric productivities reached with these yeasts in media made from charcoal-treated hydrolyzates were 0.58 and 0.91 g/L·h, respectively.     

Simultaneous speciation of inorganic chromium(III) and chromium(VI) by hollow‐fiber‐based liquid‐phase microextraction coupled with HPLC–UV

The speciation of chromium(VI) and chromium(III) was investigated by using hollow fiber liquid‐phase microextraction based on two immiscible organic solvents followed by high performance liquid chromatography with ultraviolet detection. In this method, chromium(VI) and chromium(III) reacted with ammonium pyrrolidine dithiocarbamate to produce hydrophobic complexes. Subsequently, the complexes were first extracted into a thin layer of organic solvent (n‐dodecane) present in the pores of a porous hollow fiber, and then into a μL volume of an organic acceptor (methanol) located inside the lumen of the hollow fiber. Then, the extracting organic phase was injected into the separation column of the high‐performance liquid chromatograph for the analysis of both chromium species. Effective parameters on extraction were optimized using one‐variable‐at‐a‐time method and central composite design. Under optimized conditions, a linear range of 0.25–100 and 0.5–100 μg/L (R ² > 0.998), the limits of detection of (S/N = 3) 0.08 and 0.1 μg/L and a preconcentration factor of 625 and 556 were achieved for chromium(VI) and chromium(III), respectively. The method was successfully applied to the speciation and determination of chromium species in different water samples and satisfactory results were obtained.     

Removal of lipopolysaccharide and reactive oxygen species using sialic acid immobilized polysulfone dialyzer

Sialic acid (N‐acetylneuraminic acid, NANA) was covalently immobilized onto the surface of a polysulfone (PSF) hollow fiber membrane. Prior to the immobilization, the surface of PSF was treated with ozone, followed by grafting with acrylic acid, and then the esterification of NANA. The surface concentration of NANA was determined by 2‐thiobarbituric acid (TBA) test. Hemocompatibility, the capability of suppressing oxidative stress, and clearance of lipopolysaccharide (LPS) from the resulting hollow fiber membrane were evaluated. The results show that by immobilizing NANA onto PSF hollow fiber, the adhesion of platelet was reduced, while both APTT and PT were little affected. Furthermore, oxidative stress was suppressed by NANA‐immobilized PSF hollow fibers. The level of LPS was also greatly reduced. Copyright © 2009 John Wiley & Sons, Ltd.     

Study on the cationic modification and dyeing of ramie fiber

A modification procedure for ramie fiber using 3-chloro-2-hydroxypropyltrimethyl ammonium chloride (CHPTAC) as a cationic agent and NaOH as a catalyst was developed in this paper. The morphological and structural transformations of the fiber induced by modification were determined by XRD (XRD), differential scanning calorimetry (DSC), and thermogravimetry analysis (TGA). XRD results show that the crystal structure of the modified fiber was still preserved although its crystallinity was decreased, which was confirmed from the TGA results. The mechanisms for the modification and dyeing of ramie fiber were analyzed, and the optimum modification conditions were determined to be the CHPTAC concentration of 30 g L⁻¹, the NaOH concentration of 15 g L⁻¹, the reaction temperature of 50 °C, and the reaction time of 60 min. The raw and the modified fibers were dyed with C.I. reactive red 2. The K/S values for the cationic modified fiber increased to be three times as high as the unmodified fiber. The dye uptakes increased greatly with an increase in the nitrogen contents up to 0.4% on the modified fibers.     

Screening and quantification of anticancer compounds in traditional Chinese medicine by hollow fiber cell fishing and hollow fiber liquid/solid‐phase microextraction

Hollow fiber cell fishing, based on HepG‐2, SKOV‐3, and ACHN cancer cells, and hollow fiber liquid/solid microextraction with HPLC were developed and introduced for researching the anticancer activity of Rhizoma Curcumae Longae, Radix Curcumae, and Rhizoma Curcumae. The structures of curcumin, demethoxycurcumin, and bisdemethoxycurcumin screened were identified and their contents were determined. The compound target fishing factors and cell apoptosis rates under the effect of the three medicines were determined. The binding sites (cell membrane and cell organelle) and binding target (phospholipase C) on the cell were researched. Hollow fiber liquid/solid‐phase microextraction mechanism was analyzed and expounded. Before the application, cell seeding time, growth state and survival rate, compound nonspecific binding, positive and negative controls, repeatability in hollow fiber cell fishing with high‐performance liquid chromatography; extraction solvent, sample pH, salt concentration, agitation speed, extraction time, temperature and sample volume in hollow fiber liquid/solid‐phase microextraction with high‐performance liquid chromatography were investigated. The results demonstrated that the proposed strategy is a simple and quick method to identify bioactive compounds at the cellular level as well as determine their contents (particularly trace levels of the bioactive compounds), analyze multicompound and multitarget entirety effects, and elucidate the efficacious material base in traditional medicine.