瑞利布里渊光时域分析系统中电光调制器的理论模型与实验研究

瑞利布里渊光时域分析系统能够以非破坏性方式实现单光源、单端工作,利用强度型电光调制器同时调制脉冲基底和脉冲信号是获得该系统所需连续光和脉冲光的关键技术.本文理论分析、仿真和实验研究了一种将脉冲信号输入到电光调制器偏置端、微波信号输入到电光调制器射频端同时调制脉冲基底和脉冲信号的新调制方法,探讨了电光调制器用于瑞利布里渊光时域分析系统时的最佳工作点问题.结果表明,当调制脉冲基底和脉冲时分别将电光调制器偏置在传输曲线的谷点和峰点,并根据实际系统的组成和性能指标要求选择合适的微波调制信号幅度,可获得满足瑞利布里渊光时域分析系统要求的连续光和脉冲光.本文的研究结果为瑞利布里渊光时域分析系统的最佳化设计提供了理论依据.     

瑞利布里渊光时域分析系统中电光调制器的理论模型与实验研究

瑞利布里渊光时域分析系统能够以非破坏性方式实现单光源、单端工作,利用强度型电光调制器同时调制脉冲基底和脉冲信号是获得该系统所需连续光和脉冲光的关键技术.本文理论分析、仿真和实验研究了一种将脉冲信号输入到电光调制器偏置端、微波信号输入到电光调制器射频端同时调制脉冲基底和脉冲信号的新调制方法,探讨了电光调制器用于瑞利布里渊光时域分析系统时的最佳工作点问题.结果表明,当调制脉冲基底和脉冲时分别将电光调制器偏置在传输曲线的谷点和峰点,并根据实际系统的组成和性能指标要求选择合适的微波调制信号幅度,可获得满足瑞利布里渊光时域分析系统要求的连续光和脉冲光.本文的研究结果为瑞利布里渊光时域分析系统的最佳化设计提供了理论依据.     

调制损耗对硅基MZI结构光调制器非线性特性的影响

针对基于马赫-曾德干涉仪结构的硅基光调制器中非线性电光响应的问题,采用包含PN结非线性调制损耗和非线性折射率变化的模型,通过数值仿真方法,研究了上下两臂对称和不对称两种情况下,调制损耗对硅基光调制器非线性的影响.对比考虑调制损耗和忽略调制损耗的模型,发现在常规大信号情况下,当光调制器偏置相位为0时,调制损耗使得三次谐波增强,四次谐波减弱;当光调制器偏置相位为π/2时,调制损耗使得二次和四次谐波增强;而在小信号情况下,三次和四次等高次谐波不明显,在光调制器偏置相位为0时,调制损耗在光调制器上下两臂不对称情况下增加了基频分量串扰;在光调制器偏置相位为π/2时,调制损耗的影响主要表现为增加了二次谐波分量.     

基于双音外差的电光相位调制器半波电压自校准测量方法

电光相位调制器是光纤通信系统、微波光子系统和相干光通信系统中的关键器件之一. 作为器件本征参数, 电光相位调制器的半波电压通常利用光谱方法和电谱方法进行测量. 光谱方法受到光源线宽和光谱仪分辨率限制, 测量的分辨率较低; 电谱方法则需要光电检测之前将相位调制转换成强度调制, 电谱方法的主要困难在于需要对探测器的不平坦响应进行额外校准. 提出了利用双音外差实现电光相位调制器半波电压自校准测量新方法, 该方法利用双音电光相位调制的边带与移频光载波的外差拍频, 对外差拍频信号进行频谱分析, 获得电光相位调制器的半波电压; 通过设定双音调制信号的频率关系, 克服了探测器光电转换中的不平坦频率响应, 实现了自校准测量. 该方法可扩展探测器和频谱仪的测试频率两倍以上, 节省至少一半的带宽需求. 与光谱测量方法相比, 该方法测试分辨率大幅提高且避免了光源线宽的影响; 与传统电域测量方法相比, 该方法无须额外校准, 无驱动功率和工作波长限制, 且对测试仪器带宽需求降低一半以上. 实验证实了所提方法获得的电光相位调制器半波电压的测量结果与光谱分析法获得的结果一致, 且大幅度地提高了测量范围和分辨率. 该方法提供了非常简单的电光相位调制器微波特性化分析方法, 对其他光电子器件分析也提供了参考.     

利用电光相位调制和交叉相位调制制作时间透镜的实验及仿真分析

对时间成像理论进行简要研究. 利用电光相位调制器进行光脉冲压缩实验,并分别对基于电光相位调制和交叉相位调制的时间透镜组成的时间成像系统进行了仿真和讨论. 实验结果表明,基于电光相位调制的时间透镜组成的时间成像系统可以有效压缩光脉冲,但是该系统受到了孔径限制,压缩系数较小,分辨率较低. 进一步的仿真分析结果表明,基于交叉相位调制的时间透镜组成的时间成像系统不受孔径限制,能够获得更大的压缩系数和更高的分辨率,但是该系统的实现难度较大. 关键词： 光脉冲压缩 时间透镜 电光相位调制 交叉相位调制     

一种倍频光电振荡器的实现方法

提出了一种利用电光调制器的非线性效应实现光电振荡器倍频输出的方法,通过在光电振荡环路中引入微波分频器,使得利用低频率的电光调制器有可能产生高频率的微波倍频信号输出,从而降低了振荡频率对调制器工作频率的要求。理论和实验研究表明,在微波信号输入功率较低时,调制器将引入较大的附加噪声,会严重恶化光电振荡器输出的倍频微波信号的相位噪声。通过在振荡反馈环路中增加一个微波放大器,减小附加噪声,能够极大地改善倍频信号的相位噪声。当环路光纤为1km时,产生的9GHz倍频信号相位噪声在10kHz频率偏移时达到-104dBc/Hz,比典型光电振荡环路恶化了6dB,同时,保持了较高的输出功率。实验结果与理论分析基本一致,证明了该倍频输出光电振荡器的可行性。     

星间微波光子链路调制方式的优化

针对外调制星间微波光子链路输出信噪比优化问题,建立了基于双电极马赫 曾德尔调制器的强度调制直接探测星间微波光子链路模型,通过优化调制器调制方式来提高链路性能。用数值模拟方法得到了单边带、双边带和推挽式3种调制方式下链路输出信噪比,利用曲面投影法求得了最优调制方式时一定信噪比要求下发射端所需最小光放大器增益和对应的调制器直流偏置相位。结果表明:相同输入射频信号功率和发射光功率情况下,双边带调制输出信噪比比单边带调制高3 dB,低直流偏置相位推挽调制可以进一步优化输出信噪比。输入射频信号功率为-20 dBm,输出信噪比为17.3 dB时,所需最小光放大器增益为43.9 dB,对应的直流偏置相位为0.87。     

基于偏置纳米线的石墨烯表面等离激元调制器

开发高性能的电光调制器对于构建片上光子回路非常重要.鉴于纳米线结构具备独特的电场横向束缚特点,设计一种基于纳米线的混合表面等离激元波导电光调制器,该调制器由偏置双硅纳米线、双石墨烯层以及置于双石墨烯层之间的银纳米线构成.利用二维时域有限差分算法计算分析结构参数对器件调制性能的影响.模拟结果表明,所设计的调制器在1550 nm的工作波长下可以实现较为出色的调制性能,其3 dB调制带宽高达250 GHz,调制深度和功耗分别高于0.15 dB/μm和低于11.5 fJ/bit,该调制器可为新一代高性能集成电光调制器的开发提供设计思路.     

调制器低偏置方案优化光电振荡器相位噪声

提出了采用调制器低偏置方案来降低光电振荡器(OEO)的相位噪声方案并得到了实验验证.调制器的大光功率注入与低偏置点设置能够降低噪信比,进而降低输出信号的相位噪声.实验证明,当60 mW光功率注入时,在低偏置点能得到相噪的最低值,该值比正交偏置点对应的相噪值下降了2.8 dB.     

基于相位/强度调制的伪毫米波超宽带信号的光学辅助探测（英文）

针对伪毫米波超宽带信号脉冲宽度窄且信号强度低而不易探测的特点,本文提出了两种光学辅助包络探测方案.将伪毫米波超宽带信号调制到光载波上,利用光纤布喇格光栅带通滤波器滤出调制器输出的第一边带信号,通过光电探测器和低通滤波器便可以得到用于判决的伪毫米波超宽带信号的包络信息.数学推导和仿真分析了分别采用相位调制器和强度调制器对输出包络信号振幅的影响.研究结果表明:强度调制器需要偏置控制电路来稳定偏置点的位置,当强度调制器工作在最小传输点时,得到的包络信号幅值最大;相位调制器无需偏置控制电路,其输出信号包络的幅值等于使用强度调制器的系统可得到的最大值;使用相位调制器的系统较使用强制调制器的系统具有结构更简单和插入损耗更低的特点.     

A method of developing wavelength encoded all-optical S–R flip-flop by the uses of semiconductor optical amplifier based Mach–Zenhder interferometer and phase conjugation system

A scheme for a high-speed wavelength encoded all-optical S–R flip-flop (or a digital memory cell for storing of optical bits) based on wavelength conversion (MZI) in semiconductor optical amplifier (SOA) and phase conjugation system (PCS) is proposed. The switching action of semiconductor optical amplifier (SOA) does not give too high operational speed because of electrical pumping power. But optical phase conjugation mechanism gives us ultrahigh operational speed. So, joint use of them gives rise to a more high speed system comparatively to only SOA based switches. Here two logic states of the whole system is encoded by two wavelengths as well as frequencies, since the information in the bit is unaffected throughout the communication not having regard to the loss of light energy due to reflection, refraction polarization, etc.     

KGW晶体外腔式高功率579nm喇曼黄光激光器

报道了579nm高功率KGd(WO4)2喇曼晶体外腔式喇曼黄光激光器的输出特性.基于808nm脉冲激光二极管侧面泵浦Nd∶YAG陶瓷、腔内BBO电光晶体同步延迟调Q和Ⅰ类临界相位匹配的LBO晶体腔外倍频方案,并通过外腔式KGW晶体Ng轴二阶斯托克斯喇曼频移,获得了579.54nm黄光激光输出.当脉冲信号重复频率为1kHz、532nm泵浦光最高平均功率为5.02W、脉冲宽度为10.1ns时,获得了最高平均功率2.58 W、脉冲宽度7.4ns、峰值功率348.6kW的579.54nm二阶斯托克斯喇曼黄光激光输出;532nm至579.54nm的光-光转化效率为51.4%、斜率效率为54.8%,光束质量因子Mx2-579.54=5.829、My2-579.54=6.336,输出功率不稳定性小于±2.35%.实验表明:外腔式喇曼结构能够高效地获得喇曼黄光,具有很高的光-光转化效率及良好的功率稳定性,并通过脉冲LD结合同步延迟电光调Q可获得高重复频率、高平均功率、窄脉冲宽度和高峰值功率的黄光激光输出.     

半“V”字形铁电液晶器件的制备

实验研究了N*-Sc*相变时施加直流电压的强度对铁电液晶分子层排列和电光性能的影响,由此筛选了合适的直流电压强度,并研制了可实现连续灰度级的半“V”字形铁电液晶样品.实验说明N*-Sc*相变时施加直流电压强度大有利于获得性能良好的器件.采用N*-Sc*相变施加4V/μm直流电压,制备半“V”字形铁电液晶器件,经测试器件饱和电压为5V,对比度为112.8,上升时间和下降时间分别为622.14 μs和374.7 μs.     

一种基于全息光处理器的可调光编码/解码器设计

提出了一种基于全息光处理器的可调光编码-解码器的实现方案.这种新结构的可调光编码/解码器减小了硬件实现的复杂性,降低了成本和功耗,便于集成.     

A novel bits loading algorithm for adaptive modulation OFDM multimode fiber communication system

A novel bits loading algorithm is proposed for adaptively modulated optical OFDM (AMOOFDM) multimode fiber communication system to decrease the system bit error rate (BER) caused by some OFDM subcarriers located at the deep nulls in the high frequency region of multimode fiber. The simulation results show that the performance of the new algorithm is approximate to the optimal algorithm-Greedy algorithm, but its computational complexity is considerably lower, thus the new algorithm is easy to implement. Comparing to fixed bits loading, adaptive bits loading can reduce the system BER effectively.     

Photonic analog-to-digital converter based on the robust symmetrical number system

A novel approach to realizing photonic analog-to-digital conversion with Gray-code-like property is proposed and demonstrated. Instead of using Mach-Zehnder modulators (MZMs) with different half-wave voltages, an array of MZMs with identical half-wave voltages are applied to realize quantization and encoding, which greatly simplifies the implementation. Multiple comparators with preset thresholds are applied at the output of each MZM to improve the number of bits. Through properly setting the bias voltages of the MZMs, a photonic analog to digital converter (ADC) based on the robust symmetrical number system (RSNS) coding method is realized. As an example, a 3-channel structure with maximum quantization level of 17 (corresponding to 4.09 bits) is investigated in detail. We show that the differential encoding technique can be applied in the proposed structure, which increases the equivalent number of bits of the ADC system.     

Allocation Algorithm for Optical OFDM Multimode Fiber Communication System

Abstract

A fast bits allocation algorithm is proposed for adaptively modulated optical orthogonal frequency division multiplexing multimode fiber communication system to decrease the system bit error rate caused by some orthogonal frequency division multiplexing subcarriers being located at the deep nulls in the high-frequency region of multimode fiber. Based on a lookup table scheme, the new algorithm dramatically decreases the computational complexity of the Greedy algorithm. The simulation results show that the new algorithm has the same allocation result as the Greedy algorithm, but the computational complexity is considerably lower. In addition, adaptive bits allocation can effectively reduce the system bit error rate.     

VPD技术在光电产品总体设计中的应用

从系统工程方法出发，叙述了在光电系统开发的设计阶段采用VPD（Virtual Product Development）技术实现光电产品全数字化拟实平台的方法和过程。     

An all-optical bit-error indicating scheme based on self-phase modulation and filtering

In this paper, a novel all-optical bit-error indicating scheme is numerically studied. The bit-error indicating function is achieved by two all-optical processing stages. Firstly, the amplified original bit stream propagates through a high-nonlinear fiber and experiences self-phase modulation which causes intensity-dependent spectrum broadening and split. And then, the bit stream output from the high-nonlinear fiber is filtered by a band-pass filter with the same central wavelength as the original bit stream to generate an error bit indicating signal. The error bit indicating signal, in which only the “Error” bits have the highest peak power, is synchronous with the delayed original bit stream. Therefore, the position of the “Error” bits in the original bit stream can be identified by setting only one judge threshold in the error bit indicating signal. The scheme is demonstrated for an 80 Gb/s bit stream with return-to-zero format by simulation. The results show that the scheme can be used for the all-optical bit-error indicating of the super high bit-rate systems using the return-to-zero format which is favored in the optical time division multiplexing transmission systems.     

Channel reduction schemes for fiber-optic angle encoders

Three fiber-optic sensor systems designed to remotely determine angular position that achieve high angular resolution with fewer channels than comparable Gray code encoders are described. Two of the Systems use a sheet polarizer affixed to a “codewheel” and the third system uses a two-channel digital shaft encoder style “codewheel.”

The first polarization scheme uses four optical channels, two of which are analog and two digital. The ratio of the two analog channel intensities yields tan²θ. The fourfold quadrant ambiguity is resolved by the two digital channels that are transected by two semicircular masks on the polarizer codewheel (Ref. U.S. Patent No. 4,577,414, 25 Mar 1986). The second polarization scheme again uses quadrant ambiguity masks but employs only one analog channel that simulates a polarization vector that oscillates through 90°. The oscillating vector is produced by the superposition of two sine-wave-modulated beams at the polarizer codewheel. The modulations of the two beams have a phase difference that is created by time delaying one of the beams in a fiber delay loop. The phase difference between the generated composite signal and a reference signal then determines the angle of the codewheel. We have demonstrated experimentally that this type of split analog-digital scheme has a resolution equivalent to a 10-bit digital system (i.e., ±0.35°) independent of codewheel diameter.

The serial digital shaft encoder scheme uses only two digital channels and a codewheel that has two concentric masks with 48 equally spaced windows offset with respect to each other by one-half window width. At 0° there is a unique mask that initializes an up/down decoder chip (Hewlett-Packard HCTL-2000). This system has a resolution better than 7 bits using a 5-cm diameter code wheel and 1-mm Selfoc^TM lenses.

The supporting electro-optical systems including sources, fibers, lenses, mirrors, couplers, WDMs, polarizers, detectors, and signal processing for all schemes are described and the relative merits of each are compared.