Irreversible electrowetting on thin fluoropolymer films

A study was conducted to investigate electrowetting reversibility associated with repeated voltage actuations for an aqueous droplet situated on a silicon dioxide insulator coated with an amorphous fluoropolymer film ranging in thickness from 20 to 80 nm. The experimental results indicate that irreversible trapped charge may occur at the aqueous-solid interface, giving rise to contact angle relaxation. The accumulation of trapped charge was found to be related to the applied electric field intensity and the breakdown strength of the fluoropolymer. On the basis of the data, an empirical model was developed to estimate the amount of trapped charge in the fluoropolymer as well as the voltage threshold for the onset of irreversible electrowetting.     

Low voltage electrowetting using thin fluoroploymer films

This paper investigates the nonideal electrowetting behavior of thin fluoroploymer films. Results are presented for a three phase system consisting of: (1) an aqueous water droplet containing sodium dodecyl sulfate (SDS), (2) phosphorous-doped silicon topped with SiO2 and an amorphous fluoroploymer (aFP) insulating top layer on which the droplet is situated, and (3) a dodecane oil that surrounds the droplet. The presented measurements indicate that the electrowetting equation is valid down to a 6 nm thick aFP film on a 11 nm thick SiO2. At this dielectric thickness, a remarkable contact angle change of over 100 degrees can be achieved with an applied voltage less than 3 V across the system. The data also shows that for this water/surfactant/oil system, contact angle saturation is independent of the electric field, and is reached when the surface energy of the solid-water interface approaches zero.     

Dynamic and reversible electrowetting with low voltage on the dimethicone infused carbon nanotube array in air

Unremitting efforts have been intensively making for pursuing the goal of the reversible transition of electrowetting owing to its vital importance to many practical applications, but which remains a major challenge for carbon nanotubes due to the irreversible electrochemical damage. Herein, we proposed a subtly method to prevent the CNT array from electrochemical damage by using liquid medium instead of air medium to form a liquid/liquid/solid triphase system. The dimethicone dynamically refills in CNT arrays after removing of voltage that makes the surface back to hydrophobic, which is an elegant way to not only decrease energy dissipation in electrowetting process but also obtain extra energy in reversible dewetting process. Repeated cycles of in situ experiments showed that more than four reversible electrowetting cycles could be achieved in air. It worth mention that the in situ reversible electrowetting voltage of the dimethicone infused CNT array has been lowered to 2 V from 7 V which is the electrowetting voltage for the pure CNT array. The surface of the dimethicone infused CNT array can maintain hydrophobicity with a contact angle of 145.6° after four cycles, compared with 148.1° of the initial state. Moreover, a novel perspective of theoretical simulations through the binding energy has been provided which proved that the charged CNTs preferred binding with water molecules thereby replacing the dimethicone molecules adsorbed on the CNTs, whereas reconnected with dimethicone after removing the charges. Our study provides distinct insight into dynamic reversible electrowetting on the nanostructured surface in air and supplies a way for precise control of wettability in surface chemistry, smart phase-change heat transfer enhancement, liquid lenses, microfluidics, and other chemical engineering applications.     

Characteristics and durability of fluoropolymer thin films

The use of plasma-polymerised fluoropolymer (CF_xO_y) thin films in the manufacture of microelectromechanical systems (MEMS) devices is well-established, being employed in the passivation step of the deep reactive ion etching (DRIE) process, for example. This paper presents an investigation of the effect of exposure to organic and aqueous liquid media on plasma-polymerised CF_xO_y thin films. Atomic force microscopy (AFM), scanning electron microscopy (SEM), ellipsometry, X-ray photoelectron spectroscopy (XPS) and dynamic wetting measurements were all employed as characterisation techniques. Highly basic aqueous solutions, including known silicon etchants, were found to cause delamination via degradation of the countersurface below the CF_xO_y thin film. Films were found to be stable in organic solvents, acidic aqueous solutions and slightly basic aqueous solutions.     

On the performance of thermostable electrowetting agents

Electrowetting of ionic liquids (ILs) in different alkane ambient and at different temperatures were studied under different AC voltages. The performance of IL‐based electrowetting at elevated temperatures and that at room temperature was compared. It turns out that the electrowetting of ILs at elevated temperatures resulted in faster response and lower operation voltage. Furthermore, the relationship between the structure of the ion and the contact angle change was specifically investigated and theoretically explained. Finally, the properties of IL‐based electrowetting in different alkane ambient were studied. It was demonstrated that the long length of the alkyl chain guaranteed a smaller contact angle under the same applied voltage. All the experimental results showed attractive features involving wide operating temperatures and in particular high stability, fast response, and good reversibility at elevated temperatures. The performance of IL‐based electrowetting could be further improved through an optimal choice of an ambient phase or a rational design and synthesis of ionic liquids. Copyright © 2011 John Wiley & Sons, Ltd.     

Supramolecular structures in nanocomposite multilayered films

We investigate the multilayered structures of poly(ethylene)oxide/montmorillonite nanocomposite films made from solution. The shear orientation of a polymer-clay network in solution combined with simultaneous solvent evaporation leads to supramolecular multilayer formation in the film. The resulting films have highly ordered structures with sheet-like multilayers on the micrometer length scale. The polymer covered clay platelets were found to orient in interconnected blob-like chains and layers on the nanometer length scale. Inside the blobs, scattering experiments indicate the polymer covered and stacked clay platelets oriented in the plane of the film. The polymer is found to be partially crystalline although this is not visible by optical microscopy. Atomic force microscopy suggests that the excess polymer, which is not directly adsorbed to the clay, is wrapped around the stacked platelets building blobs and the polymer also interconnects the polymer-clay layers. Overall our results suggest the re-intercalation of clay platelets in films made from exfoliated polymer-clay solutions as well as the supramolecular order and hierarchical structuring on the nanometer, via micrometer to the centimeter length scale.     

Wetting and electrowetting properties of carbon nanotube templated parylene films

In this study, we compared the wetting and electrowetting properties of a planar parylene (poly(p-xylylene)) film to those of a nanostructured parylene film. To generate the nanostructured film, we used an aligned array of multiwalled carbon nanotubes as a template; a thin coating of parylene was deposited on the nanotube template to generate a parylene film with a nanoscale roughness structure. Static contact angle measurements indicated a very significant increase in the water contact angle from approximately 73 degrees for planar parylene to approximately 110 degrees for the nanotemplated parylene. In addition, we performed electrowetting experiments to dynamically tune the contact angle by application of electric potential. Interestingly, the flat parylene film showed contact angle saturation at an applied voltage of approximately 40 V, while the nanotemplated parylene film did not experience saturation in the contact angle response even for voltages up to 80 V. These results show that engineering a nanoscale roughness structure to a polymer film results in significant changes to the wetting and electrowetting properties of the polymer.     

Orientation of platelets in multilayered nanocomposite polymer films

The orientation of platelets in micro-meter-thick polymer-clay nanocomposite films was investigated with small-angle neutron scattering (SANS), small-angle X-ray scattering (SAXS), and wide-angle X-ray diffraction (WAXD). The films with various clay contents (15–60% by mass fraction) were prepared by a layer-by-layer approach from polymer-clay solutions that led to the formation of a high degree of orientation in both polymer and clay platelets. Shear-induced orientation of polymer-clay solutions is compared with the orientation of polymer-clay films. SANS, SAXS, and WAXD, with beam configurations in and perpendicular to the spread direction of the film, were used to determine the structure and orientation of platelets. In all films, the clay platelets oriented preferentially in the plane of the film. The observed differences in semidilute solutions, with clay surface normal parallel to the vorticity direction, versus bulk films and with clay surface normal parallel to the shear gradient direction at clay mass fractions of 40 and 60%, were attributed to the collapses of clay platelet during the drying process. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3237–3248, 2003     

Elaboration of spin-coated cellulose-xyloglucan multilayered thin films

In the context of developing a biomimetic model of the primary cell wall, our aim was to produce multilayered thin films composed of cellulose nanocrystals (CN) and xyloglucan (XG). We investigated the effect of XG concentrations ranging from 0.5 g/L to 10 g/L. The choice of concentration was based on rheological investigation of the XG solutions which indicated that the two lower concentrations (0.5 and 1 g/L) correspond to a semidilute regime where the polymer chains are not entangled, whereas they are entangled at the highest concentrations (5 and 10 g/L). Several processes of film preparation were tested (dipping or spin-coating, with or without a rinsing step). The film growth profiles obtained for different XG concentrations by mechanical profilometry showed that spin-coating without rinsing was the most efficient process. Results showed that at high XG concentrations (XG = 5 g/L and XG = 10 g/L) plateau values were reached after the formation of 3 or 4 bilayers, whereas growth of the multilayer structure was linear at the lower XG concentrations (XG = 0.5 g/L and XG = 1 g/L). The thickness of one CN/XG bilayer corresponded to a single layer of CN covered by a thin XG layer, despite the absence of a rinsing step between successive coatings. The importance of the XG concentration was confirmed by determining by neutron reflectivity the film architecture obtained from four XG solutions after eight successive paired coatings. The results are discussed in relation to the role of XG in the plant cell wall.     

Superior electro-optical performance in vertically aligned liquid crystal devices based on aluminum oxide films

We achieved vertically aligned (VA) liquid crystals (LCs) on aluminum oxide (Al₂O₃) films deposited via e-beam evaporation using a rubbing treatment. Uniform and vertical LC alignment was achieved and high thermal stability was obtained using these substrates. By analyzing measurements from optical retardations, we confirm that the LC orientation is adjustable using rubbing treatment. The superior electro-optical characteristics of the VA cells based on Al₂O₃ films are measured and compared with those based on polyimide layers, indicating that this approach will allow the fabrication of high-performance, advanced LC displays using a conventional rubbing process.     

Nanometer-scale decomposition of ultrathin multilayered polyelectrolyte films

We report that ultrathin multilayered films fabricated from plasmid DNA and synthetic polyamines undergo nanometer-scale transformations that resemble spinodal decomposition when incubated in aqueous media. The patterns and structures generated by this transformation are similar to those observed for the spinodal dewetting of thin films of conventional polymers. This behavior has not, however, been observed for this class of multilayered assemblies, for which long-range electrostatic interactions play significant roles in governing film structure and stability. We demonstrate that it is possible to promote this behavior, prevent it, or control it by varying polymer structure, film composition, or the conditions to which these materials are exposed. These results suggest the basis of methods that could prove useful for the generation of nanostructure on complex surfaces and contribute to methods for the localized delivery of DNA from surfaces.     

Photocurrent generation in noncovalently assembled multilayered thin films

Multilayered photocurrent generating thin films were fabricated by templated noncovalent assembly via stepwise assembly of molecular components. Each of films I-IV contained an underlying self-assembled monolayer (SAM) consisting of an alkanethiol linked covalently to a 2,6-dicarboxypyridine ligand that served as a binding site for attaching additional molecular components. The SAM subsequently was functionalized by sequential deposition of Cu(II), Co(II), or Fe(III) ions followed by a variety of substituted 2,6-dicarboxypyridine ligands as a means to incorporate one or more layers of pyrene chromophores into the film. The films were characterized by contact angle measurements, ellipsometry, grazing incidence IR, cyclic voltammetry, and impedance spectroscopy after deposition of each layer, confirming the formation of ordered, stable layers. Following incorporation into a three-electrode system, photoexcitation resulted in the generation of a cathodic photocurrent in the presence of methyl viologen and an anodic photocurrent in the presence of triethanolamine. Using this strategy, systems were fabricated that produced up to 89 nA/cm(2) of reproducible photocurrent.     

Reversible photoswitchable wettability in noncovalently assembled multilayered films

Reversible and irreversible photoinduced changes in surface wettability were observed in noncovalently assembled multilayered films. The multilayered films studied were fabricated from a self-assembled monolayer (SAM) consisting of 4-(10-mercaptodecyloxy)pyridine-2,6-dicarboxylic acid on gold, Cu(II) ions complexed to the pyridine head group of the SAM, and either cis- (film 1) or trans- (film 2) stilbene-4,4'-dicarboxylic acid complexed to the Cu(II) ions. Irradiation of film 1 at wavelengths corresponding to the absorption band of the cis-stilbene isomer resulted in an irreversible chemical change and an irreversible increase in wettability, as indicated by surface contact angle and grazing incidence IR measurements. However, no evidence for cis-/trans-photoisomerization was observed. Films 3 and 4, similar to films 1 and 2 in that they consist of an underlying SAM, an intermediate layer consisting of Cu(II) ions, and either cis- or trans-stilbene-4,4'-dicarboxylic acid as the capping ligand, were fabricated with a mixed SAM that contained both 4-(10-mercaptodecyloxy)pyridine-2,6-dicarboxylic acid and 4-tert-butylbenzenethiol. Irradiation of these films at wavelengths corresponding to stilbene isomer absorption bands resulted in reversible cis- to trans- (film 3) and trans- to cis- (film 4) photoisomerization and reversible switching of the surface wettability between a low wetting state (cis-stilbene) and a high wetting state (trans-stilbene). The difference in observed behavior between films 1 and 2 and films 3 and 4 is attributed to the greater surface spacing afforded by the mixed monolayer, which allows greater conformational flexibility and lowers the steric barriers to isomerization.     

Impact of pinning of the triple contact line on electrowetting performance

Pinning of the triple contact line adversely affects electrowetting on dielectric. Electrowetting response of substrates with contact angle hysteresis ranging from 1° to 30° has been characterized, and the results are interpreted within the framework of electromechanics corrected for pinning. The relationship between contact angle hysteresis, threshold potential for liquid actuation, and electrowetting hysteresis is quantified. Our results demonstrate that a modified electrowetting equation, based on balance of forces (including the pinning forces) acting on the triple contact line and on the drop, describes the electrowetting response of substrates with significant contact angle hysteresis. Finally, the surface properties of PDMS Sylgard 184 were found to be influenced by the electric field.     

Superior supercapacitive performance in porous nanocarbons

Porous nanocarbons with average particle size 20–40 nm were developed using biowaste oil palm leaves as a precursor.Simple pyrolysis was carried out at 700 °C under nitrogen atmosphere.Obtained porous nanocarbons showed excellent porous nature along with spherical shape.Symmetric supercapacitor fabricated from porous nanocarbons showed superior supercapacitance performance where high specific capacitance of 368 F/g at 0.06 A/g in 5 M KOH were reported.It also exhibited high stability(96% over 1700cycles) and energy density of 13 Wh/kg.Low resistance values were obtained by fitting the impedance spectra,thus indicating the availability of these materials as supercapacitors electrode.The presented method is cost effective and also in line with waste to wealth approach.     

Plasma-enhanced synthesis of thin fluoropolymer layers with low Raman and fluorescence backgrounds

Radio-frequency (RF) plasma enhanced chemical vapor deposition (PECVD) provides a promising way to deposit extremely hydrophobic, highly adherent nanometer- to micrometer-thick films with thermal stability, a low coefficient of friction, a low dielectric constant, and a low value of surface energy. We describe the synthesis of these fluorinated thin films using hexafluoropropene as starting material and discuss their properties. These coatings, applied to stainless steel, provide ideal substrates for Raman spectroscopy, when extremely low backgrounds are required. Raman spectroscopy measurements of a low-concentration protein film are used to demonstrate sensitivity and level of detectability.     

Apparent dewetting of ultrathin multilayered polyelectrolyte films incubated in aqueous environments

We have investigated and characterized changes in film morphology and surface structure that occur when ultrathin multilayered polyelectrolyte films fabricated from linear poly(ethylene imine) (LPEI), sodium poly(styrene sulfonate) (SPS), and two hydrolytically degradable polyamines (polymers 1 and 2) are incubated in physiologically relevant environments. Characterization of the physical erosion profiles of films having the structure (LPEI/SPS)10(1/SPS)4(2/SPS)4 (approximately 80 nm thick) by atomic force microscopy (AFM), reflective optical microscopy, and scanning electron microscopy (SEM) demonstrated that these materials undergo large-scale changes in surface structure and morphology upon incubation in phosphate-buffered saline (PBS) at 37 degrees C. The patterns and structures generated during this transformation (e.g., nucleation and growth of holes, coalescence of holes, formation of cell-type structures, and the subsequent breakup of these features into droplets) are similar in many ways to those observed for the dewetting of thin films of conventional polymers, such as polystyrene, on nonwetting surfaces. The processes reported here are sufficiently slow (they occur over approximately 100 h) and occur under sufficiently mild conditions (e.g., incubation in PBS at 37 degrees C) to permit characterization and quantification of the structures and features that arise during the course of these transformations. The apparent dewetting of these ultrathin films upon exposure to aqueous environments creates future opportunities to investigate and characterize processes of mass transport in this class of ionically cross-linked assemblies.