Sequential injection analysis (SIA)-chemiluminescence determination of indomethacin using tris[(2,2'-bipyridyl)]ruthenium(III) as reagent and its application to semisolid pharmaceutical dosage forms

Automated sequential injection (SIA) method for chemiluminescence (CL) determination of nonsteroidal anti-inflammatory drug indomethacin (I) was devised. The CL radiation was emitted in the reaction of I (dissolved in aqueous 50% v/v ethanol) with intermediate reagent tris(2,2′-bipyridyl)ruthenium(III) (Ru(bipy)₃³⁺) in the presence of acetate. The Ru(bipy)₃³⁺ was generated on-line in the SIA system by the oxidation of 0.5 mM tris(2,2′-bipyridyl)ruthenium(II) (Ru(bipy)₃²⁺) with Ce(IV) ammonium sulphate in diluted sulphuric acid. The optimum sequence, concentrations, and aspirated volumes of reactant zones were: 15 mM Ce(IV) in 50 mM sulphuric acid 41 μL, 0.5 mM Ru(bipy)₃²⁺ 30 μL, 0.4 M Na acetate 16 μL and I sample 15 μL; the flow rates were 60 μL s⁻¹ for the aspiration into the holding coil and 100 μL s⁻¹ for detection. Calibration curve relating the intensity of CL (peak height of the transient CL signal) to concentration of I was curvilinear (second order polynomial) for 0.1–50 μM I (r = 0.9997; n = 9) with rectilinear section in the range 0.1–10 μM I (r = 0.9995; n = 5). The limit of detection (3σ) was 0.05 μM I. Repeatability of peak heights (R.S.D., n = 10) ranged between 2.4% (0.5 μM I) and 2.0% (7 μM I). Sample throughput was 180 h⁻¹. The method was applied to determination of 1 to 5% of I in semisolid dosage forms (gels and ointments). The results compared well with those of UV spectrophotometric method.     

High throughput method for the analysis of cetrizine hydrochloride in pharmaceutical formulations and in biological fluids using a tris(2,2'-bipyridyl)ruthenium(II)-peroxydisulphate chemiluminescence system in a two-chip device

A fast, economic and sensitive chemiluminescence (CL) method has been developed for the analysis of cetrizine hydrochloride (CET) in pharmaceutical formulations and in biological fluids. The CL method is based on the oxidation of tris(2,2′-bipyridyl)ruthenium(II) (Ru (bipy)₃²⁺) by peroxydisulphate in a two-chip device. Up to 180 samples can be analysed per hour, consuming only minute quantities of reagents. Three instrumental setups were tested to find the most economical, sensitive and high throughput setup. In the first setup, a continuous flow of sample and CL reagents was used, whereas in the second setup, a fixed volume (2 μL) of (Ru (bipy)₃²⁺) was introduced into a continuous infusion of peroxydisulphate and the sample. In the third design, a fixed volume of sample (2 μL) was injected while the CL reagents were continuously infused. Compared to the first setup, a 200% signal enhancement was observed in the third setup. Various parameters that influence the CL signal intensity, including pH, flow rates and reagent concentrations, were optimized. A linear response was observed over the range of 50 μg L⁻¹ to 6400 μg L⁻¹ (R² = 0.9959) with RSD values of 1.1% (n = 15) for 1000 μg L⁻¹. The detection limit was found to be 15 μg L⁻¹ (S/N = 3). The amount of consumed sample was only 2 μL, from which the detected amount of CET was found to be 6.5 × 10⁻¹⁴ mol. This procedure was successfully applied to the analysis of CET in pharmaceutical formulations and biological fluids.     

A novel flow injection chemiluminescence determination of Cr(VI) with Dichlorotris(1,10-phenanthroline)ruthenium(II)

A selective novel reverse flow injection system with chemiluminescence detection (rFI-CL) for the determination of Cr(VI) in presence of Cr(III) with Dichlorotris (1,10-phenanthroline)ruthenium(II), (Ru(phen)₃Cl₂), is described in this work. This new method is based on the oxidation capacity of Cr(VI) in H₂SO₄ media. First, the Ruthenium(II) complex is oxidized to Ruthenium(III) complex by Cr(VI) and afterwards it is reduced to the excited state of the Ruthenium(II) complex by a sodium oxalate solution, emitting light inside the detector. The intensity of chemiluminescence (CL) is proportional to the concentration of Cr(VI) and, under optimum conditions, it can be determined over the range of 3-300 μg L⁻¹ with a detection limit of 0.9 μg L⁻¹. The RSD was 8.4% and 1.5% at 5 and 50 μg L⁻¹, respectively. For the rFI-CL method various analytical parameters were optimized: flow rate (1 mL min⁻¹), H₂SO₄ carrier concentration (20% w/V), Ru(phen)₃Cl₂ concentration (5 mM) and sodium oxalate concentration (0.1 M). The effect of Cr(III), Fe(III), Al(III), Cd(II), Zn(II), Hg(II), Pb(II), Ca(II) and Mg(II), was studied. The method is highly sensitive and selective, allowing a fast, on-line determination of Cr(VI) in the presence of Cr(III). Finally, the method was tested in four different water samples (tap, reservoir, well and mineral), with good recovery percentage.     

Immobilization of tris(1,10-phenanthroline)ruthenium with graphene oxide for electrochemiluminescent analysis

Electrochemiluminescence (ECL) of ruthenium complexes has broad applications and the immobilization of Ru(bpy)₃²⁺ has received extensive attention. In comparison with Ru(bpy)₃²⁺, Ru(phen)₃²⁺ can be immobilized more easily because of its better adsorbability. In this study, immobilization of Ru(phen)₃²⁺ for ECL analysis has been demonstrated for the first time by using graphene oxide (GO) as an immobilization matrix. The immobilization of Ru(phen)₃²⁺ is achieved easily by mixing Ru(phen)₃²⁺ with GO without using any ion exchange polymer or covalent method. The strong binding of Ru(phen)₃²⁺ with GO is attributed to both the π–π stacking interaction and the electrostatic interaction. The Ru(phen)₃²⁺/GO modified electrode was characterized by using tripropylamine (TPA) as the coreactant. The linear range of TPA is from 3 × 10⁻⁷ to 3 × 10⁻² mol L⁻¹ with the detection limit of 3 × 10⁻⁷ mol L⁻¹. The ECL sensor demonstrates outstanding long-term stability. After the storage in the ambient environment for 90 days, the ECL response remains comparable with its original signal.     

Determination of proline in wine using flow injection analysis with tris(2,2'-bipyridyl)ruthenium(II) chemiluminescence detection

Flow injection methodology is described for the determination of proline in red and white wines using tris(2,2′-bipyridyl)ruthenium(II) chemiluminescence detection. Selective conditions were achieved for proline at pH 10, while other amino acids and wine components did not interfere. The precision of the method was less than 1.00% (R.S.D.) for five replicates of a standard (4 × 10⁻⁶ M) and the detection limit was 1 × 10⁻⁸ M. The level of proline in white and sparkling wines using the developed methodology was equivalent to those achieved using HPLC-FMOC amino acid analysis. SPE removal of phenolic material was required for red wines to minimize Ru(bipy)₃³⁺ consumption and its associated effect on accuracy.     

Characterization of the low-oxidation-potential electrogenerated chemiluminescence of tris(2,2′-bipyridine)ruthenium(II) with tri-n-propylamine as coreactant

The electrogenerated chemiluminescence (ECL) of the Ru(bpy)₃²⁺ (bpy, 2,2′-bipyridine)/tri-n-propylamine (TPrA) system can be produced at an oxidation-potential well before the oxidation of Ru(bpy)₃²⁺. Here, we describe the unique features of the low-oxidation-potential (LOP) ECL. The LOP ECL exhibited strong dependence on solution pH with the maximum emission at pH  7.7. Compared with the conventional ECL, the LOP ECL was much more significantly diminished at high pH (>10), probably due to the short lifetime of TPrA cation radical which is a crucial intermediate for the LOP emission. It was also found that the preceding deprotonation step played an important role in TPrA oxidation at neutral pH and would remarkably influence the emission intensity. As excess intermediate radicals were produced upon rapid TPrA oxidation, only 5 mM TPrA was needed to achieve the maximum LOP ECL intensity in detecting trace Ru(bpy)₃²⁺ (<1 μM) and the LOP ECL response to Ru(bpy)₃²⁺ concentration was linear. Compared with the conventional Ru(bpy)₃²⁺/TPrA ECL, the LOP ECL technique not only produces higher emission intensity at lower oxidation-potential, but also significantly reduces the amount of the coreactant.     

Quality control of PET radiopharmaceuticals by high‐performance liquid chromatography with tris(2,2′‐bipyridyl)ruthenium(II) electrogenerated chemiluminescence detection

A highly sensitive reversed‐phase liquid chromatographic (HPLC) method was investigated to analyze a range of positron emission tomography (PET) radiopharmaceuticals using electrogenerated chemiluminescence (ECL) detection. ECL is based on the reaction of PET molecules with tris(2,2′‐bipyridyl)ruthenium(III) [Ru(bpy)₃³⁺], which is generated through the on‐line electro‐oxidation of Ru(bpy)₃²⁺. In 21 different radiopharmaceuticals studied, 18 compounds could be detected with detection limits (signal‐to‐noise ratio = 3) of 0.12–72 ng/mL per 20 μL injection. Sufficient reproducibility and linearity were obtained for the quantitative determination of PET molecules in pharmaceutical fluid. This method could be successfully applied to quality control tests of PET radiopharmaceuticals with ultra‐high specific radioactivity. Copyright © 2009 John Wiley & Sons, Ltd.     

Enhancement of on chip chemiluminescence signal intensity of tris(1,10-phenanthroline)-ruthenium(II) peroxydisulphate system for analysis of chlorpheniramine maleate in pharmaceutical formulations

The effect of detection chip geometry on chemiluminescence (CL) signal intensity of tris(1,10-phenanthroline)-ruthenium(II) peroxydisulphate system for analysis of chlorpheniramine maleate (CPM) in pharmaceutical formulations was investigated. It was observed that the design of the detection chip is very crucial and can play an important role in enhancing the CL signal intensity in this system. The CL signal intensity was enhanced 250% when a teardrop micromixer chip was used, compared to the commonly used serpentine chip geometry. The study was conducted using a multi-chip device. In this device, chip 1 was used to prepare and pump the reagent mixture, whereas chip 3 was used for pumping the sample. The two chips were connected to the teardrop chip (2) via silica capillary where detection took place. Non-linear regression curve fitting of the calibration data revealed that the calibration curves are best described by third order polynomial equation with excellent correlation coefficients (R² = 0.9998) for the concentration range 7.69 × 10⁻⁸ to 5.12 × 10⁻⁵ mol L⁻¹. A linear response is also observed over the range 7.69 × 10⁻⁸ to 1.28 × 10⁻⁵ mol L⁻¹ (R² = 0.9996) and the detection limit was found to be 5.49 × 10⁻⁸ mol L⁻¹. The device was successfully used for the analysis of CPM in tablets and a multi-component cough syrup. Results were reproducible with relative standard deviation (RSD) of 0.6-1.1%.     

Electrogenerated chemiluminescence: an oxidative-reductive mechanism between quinolone antibiotics and tris(2,2'-bipyridyl)ruthenium(II)

The cyclic voltammetry and electrogenerated chemiluminescent (ECL) reactions of a series of quinolone and fluoroquinolone antibiotics were investigated in a flow injection analysis (FIA) system. 7-Piperazinyl fluoroquinolone antibiotics were found to participate as a coreactant in an oxidative-reductive ECL mechanism with tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) as the luminescent reagent. The reaction mechanism was investigated in order to understand and optimize the processes leading to light emission. The optimal conditions included a solution pH ∼7 at a flow rate of 3.0 mL min⁻¹ with no added organic modifier and application of 1.2 V vs. a Pt quasi-reference electrode (QRE). Fluoroquinolones containing a tertiary distal nitrogen on the piperazine ring, such as enrofloxacin and ofloxacin, reacted to produce more intense ECL than those with a secondary nitrogen, such as ciprofloxacin and norfloxacin. The method linear range, precision, detection limits, and sensitivity for the detection of enrofloxacin and ciprofloxacin were compared to that of tripropylamine. The method was applied to the determination of the ciprofloxacin content in a pharmaceutical preparation. The assay is discussed in terms of its analytical figures of merit, ease of use, speed, accuracy and application to pharmaceutical samples.     

Effect of oxidant type on the chemiluminescence intensity from the reaction of tris(2,2′-bipyridyl)ruthenium(III) with various organic acids

An investigation into the chemiluminescence of fourteen organic acids and tris(2,2′-bipyridyl)ruthenium(II) was undertaken. Particular emphasis was placed upon the method of production of the reagent, tris(2,2′-bipyridyl)ruthenium(III), with cerium(IV) sulfate, potassium permanganate, lead dioxide and electrochemical generation. Analytically useful chemiluminescence was observed when Ce(IV) or potassium permanganate were employed as oxidants. The kinetics of analyte oxidation was related to the intensity of the chemiluminescence emission, which increased by three orders of magnitude for tartaric acid after 40 h of oxidation.     

One-step immobilization of tris(2,2'-bipyridyl)ruthenium(II) via vapor-surface sol-gel deposition towards solid-state electrochemiluminescence detection

A novel method for immobilization of tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃Cl₂) on electrode surfaces based on the vapor-surface sol-gel deposition strategy is first demonstrated in this paper. Ru(bpy)₃Cl₂ immobilized sol-gel (Ru(bpy)₃Cl₂/sol-gel) films were characterized by UV-vis spectroscopy and field-emitted scanning electron microscopy (FE-SEM). These results showed that Ru(bpy)₃Cl₂ was successfully incorporated into the silica sol-gel film. It was found that many irregular Ru(bpy)₃Cl₂/sol-gel clusters were formed on surfaces through one deposition and thick sol-gel films were observed after further deposition. Electrochemical properties and electrochemiluminescence (ECL) behaviors of Ru(bpy)₃Cl₂/sol-gel films could be easily adjusted by deposition numbers and time. At last, the Ru(bpy)₃Cl₂/sol-gel film modified electrode was used for solid-state ECL detection of tripropylamine. The linear range was from 5.8 × 10⁻⁸ to 2.4 × 10⁻⁴ M with the detection limit of 5 nM, which was three orders of magnitude lower than that from pure Nafion-modified electrodes. The ECL sensor also exhibited high stability, and still remained 92% response after being stored in air for 35 days. This method for immobilization of Ru(bpy)₃Cl₂ is simple, convenient and low-cost relative to others, so it shows promising applications in solid-state ECL detection.     

Determination of sodium oxalate in Bayer liquor using flow-analysis incorporating an anion exchange column and tris(2,2′-bipyridyl)ruthenium(II) chemiluminescence detection

Semi-automated flow injection instrumentation, incorporating a small anion exchange column coupled with tris(2,2′-bipyridyl)ruthenium(II) (Ru(bipy)₃²⁺) chemiluminescence detection, was configured and utilised to develop rapid methodology for the determination of sodium oxalate in Bayer liquors. The elimination of both negative and positive interferences from aluminium(III) and, as yet, unknown concomitant organic species, respectively are discussed. The robustness of the methodology was considerably enhanced by using the temporally stable form of the chemiluminescence reagent, tris(2,2′-bipyridyl)ruthenium(III) perchlorate in dry acetonitrile. Real Bayer process samples were analysed and the results obtained compared well with those performed using standard methods within industrial laboratories.     

Determination of riboflavin by enhancing the chemiluminescence intensity of peroxomonosulfate-cobalt(II) system

A weak chemiluminescent (CL) emission was observed in the decomposition of peroxomonosulfate (HSO5-), which would be accelerated in the presence of trace amounts of cobalt (II). The mechanism was due to the production of singlet oxygen (1O2). Interestedly, riboflavin can enhance the CL and the CL intensity was strongly dependent on riboflavin concentration. Based on this phenomenon, a flow injection analysis (FIA) CL method was established for the determination of riboflavin. Additionally, the possible CL mechanism is proposed based on the kinetic curve of the CL reaction, CL spectra, UV-vis spectra and fluorescent spectra. The CL intensity was correlated linearly with concentration of riboflavin over the range of 1.0x10(-4) to 1.0x10(-8) g mL-1; the detection limit was 9.0x10(-9) g mL-1(S/N=3); the relative standard deviation was 1.4% for 9x10(-7) g mL-1 riboflavin (n=11). Furthermore, this method was applied to the determination of riboflavin in real tablets and injections successfully.     

Determination of sophoridine and related lupin alkaloids using tris(2,2′-bipyridine)ruthenium electrogenerated chemiluminescence

Electrogenerated chemiluminescences (ECLs) based on tris(2,2′-bipyridine)ruthenium(II) (Ru(bpy)₃²⁺) and lupin alkaloids, for instance, sophoridine (SRI), matrine (MT), sophoranol (SR) and sophocarpine (SC) in an aqueous alkaline buffer solution (pH 9.0) are studied. The light emission is mainly caused by an electro-oxidation reaction between tertiary amino group on the alkaloid compounds and Ru(bpy)₃²⁺ in a thin layer flow cell equipped with a glassy carbon disc electrode (22.1 mm²) at the potential of +1.50 V (versus Ag/AgCl). The luminescence wavelength of 610 nm confirmed that ECL is caused by Ru(bpy)₃^2+∗ to its ground state. ECL intensities of these lupin alkaloids are affected by the substituent character, three-dimensional conformation of hydrogen on β-carbon atom. Ionization potentials taken from calculation data further confirm the experimental results. In addition, the factors affecting the determination and HPLC separation of the four alkaloids are also investigated.     

Synthesis and photophysical properties of novel amphiphilic ruthenium (II) complexes containing 4,4′‐dialkylaminomethyl‐2,2′‐bipyridyl ligands

The synthesis of a number of new 2,2′‐bipyridine ligands functionalized with bulky amino side groups is reported. Three homoleptic polypyridyl ruthenium (II) complexes, [Ru(L)₃]²⁺ 2(PF₆^?), where L is 4,4′‐dioctylaminomethyl‐2,2′‐bipyridine (Ru4a), 4,4′‐didodecylaminomethyl‐2,2′‐bipyridine (Ru4b) and 4,4′‐dioctadodecylaminomethyl‐2,2′‐bipyridine (Ru4c), have been synthesized. These compounds were characterized and their photophysical properties examined. The electronic spectra of three complexes show pyridyl π → π* transitions in the UV region and metal‐to‐ligand charge transfer bands in the visible region. Copyright © 2005 John Wiley & Sons, Ltd.     

Preliminary evaluation of monolithic column high-performance liquid chromatography with tris(2,2′-bipyridyl)ruthenium(II) chemiluminescence detection for the determination of quetiapine in human body fluids

High-performance liquid chromatography (HPLC) with tris(2,2′-bipyridyl)ruthenium(II) chemiluminescence detection methodology is reported for the determination of the atypical antipsychotic drug quetiapine and the observation of its major active and inactive metabolites in human urine and serum. The method uses a monolithic chromatographic column allowing high flow rates of 3 mL min⁻¹ enabling rapid quantification. Flow injection analysis (FIA) with tris(2,2′-bipyridyl)ruthenium(II) chemiluminescence detection and HPLC time of flight mass spectrometry (TOF-MS) were used for the determination of quetiapine in a pharmaceutical preparation to establish its suitability as a calibration standard. The limit of detection achieved with FIA was 2 × 10⁻¹¹ mol L⁻¹ in simple aqueous solution. The limits of detection achieved with HPLC were 7 × 10⁻⁸ and 2 × 10⁻¹⁰ mol L⁻¹ in urine and serum, respectively. The calibration range for FIA was between 5 × 10⁻⁹ and 1 × 10⁻⁶ mol L⁻¹. The calibration ranges for HPLC were between 1 × 10⁻⁷-1 × 10⁻⁴ and 1 × 10⁻⁸-1 × 10⁻⁴ mol L⁻¹ in urine and serum, respectively. The quetiapine concentrations in patient samples were found to be 3 × 10⁻⁶ mol L⁻¹ in urine and 7 × 10⁻⁷ mol L⁻¹ in serum. Without the need for preconcentration, the HPLC detection limits compared favourably with those in previously published methodologies. The metabolites were identified using HPLC-TOF-MS.     

On-line chemical generation of tris(2,2'-bipyridyl)ruthenium(III) and its application in CE with chemiluminescence detection

A novel tris(2,2'-bipyridyl)ruthenium(III) [Ru(bipy)(3) (3+)]-based chemiluminescence (CL) detection in CE using an on-line chemical generation scheme has been demonstrated. Two continuous streams respectively containing solutions of Ru(bipy)(3) (2+) and acidic cerium(IV) used as a homogeneous chemical oxidant are employed to generate Ru(bipy)(3) (3+), which is delivered into the reaction capillary of a coaxial flow interface and then reacted with analytes at the end of the separation capillary to yield light. The important operational parameters for separation and detection are identified and optimized. Four alpha-ketocarboxylic acids used as models, outside of the amine-containing compounds, are successfully separated and detected to evaluate the feasibility of the approach. The excellent resolution and detection sensitivity was achieved by using 50 mmol/L phosphate running buffer (pH 9.5) with 0.7 mmol/L CTAB, and CL reagent solution streams containing 0.15 mmol/L Ru(bipy)(3) (2+) and 0.8 mmol/L cerium(IV) (0.25 mol/L H(2)SO(4)), respectively. The concentration detection limits for alpha-ketocarboxylic acids were below 3.7x10(-8) mol/L (S/N = 3). The proposed method was applied to the determination of alpha-ketocarboxylic acids in five different honey samples with satisfactory results.     

Luminescence quenching of tris(2,2′-bipyridine)ruthenium(II) by phenol and dichlorophenols in sol-gel-processed spin-coated thin films

The luminescence spectral behaviour of the ruthenium(II)-tris-1,2-bipyridine ion (Ru(bpy)₃²⁺) included in organically modified silicate gel matrixes, and the luminescence quenching by phenol and dichlorophenols were investigated. The chloro-derivatives were 2,4-, 2,5- and 2,6-dichlorophenol. Sol-gel technology was used to prepare the “sol” with the precursor methyltriethoxysilane. Coating thin films were obtained from the “sol” by spin coating on glass slide. The Ru(bpy)₃²⁺ luminescence quenching experiments were carried out with the quencher in aerated aqueous solution at pH 12 in contact with the film. It was possible to observe an important blue shift in the Ru(bpy)₃²⁺ emission spectrum included in the films with respect to the aqueous solution. The quenching plots obtained showed a downward curvature. These plots could be fitted satisfactorily by a sum of two terms of Stern-Volmer with quenching constants K_SV1 and K_SV2 associated to two different binding sites of the ruthenium complex, which indicates the presence of a matrix microheterogeneity in the films. The K_SV1 and K_SV2 values and the corresponding fractions of the total emission f₀₁ and f₀₂ for both sites in the films suggest that only a low percentage of the probe is accessible to the quencher and that the probe is efficiently quenched in one of the sites. This site of the probe was assigned to the Site 1 in the results analysis. The value of its respective constant, K_SV1, was higher than the value of the constant K_SV in homogeneous aqueous solution for the studied quenchers, phenol and dichlorophenols.     

Effect of a carboxyl group on the chemiluminescent reaction of tris(2,2′-bipyridine)ruthenium(III) with aliphatic amines

The effect of a carboxyl group beside nitrogen of aliphatic amines on the tris(2,2′-bipyridine)ruthenium(III), Ru(bpy)₃³⁺, chemiluminescent reaction was examined. It has been shown that a carboxylate anion promotes the chemiluminescent reaction at a lower pH and then the aliphatic amines with this substituent can be sensitively detected compared with corresponding aliphatic amines without this substituent. Based on this finding, preliminary studies on simultaneous determination of 4-hydroxyproline, N-methylglycine, N-methylalanine, proline, and pipecolic acid in human serum have been performed using isocratic reversed-phase ion-pair high-performance liquid chromatography (HPLC) with electrogenerated Ru(bpy)₃³⁺ chemiluminescent detection. The detection limits (signal-to-noise ratio of 3) with the proposed method were 3.0, 12, 2.7, 4.6, and 10 nM for 4-hydroxyproline, N-methylglycine, N-methylalanine, proline, and pipecolic acid, respectively.     

Chemiluminescence method for the determination of mitoxantrone by the enhancement of the tris-(4,7-diphenyl-1,10-phenanthrolinedisulfonic acid)ruthenium(II)–cerium(IV) system

2,5-Dimercapto-1,3,4-thiadiazole (DMTD) self-assembled monolayer on gold electrode was prepared and investigated by electrochemical measurement. The DMTD/Au electrode exhibited a significantly increased sensitivity and selectivity for Pb(II) in acetate buffer (pH 5.5) at a potential of −1.0 V (vs Ag/AgCl) for 4 min by anodic stripping voltammetry. The influence of various experimental parameters on the voltammetric response was studied. Under the optimized working conditions, the dependence of the stripping peak current response on concentration of Pb(II) was linear in the range of 1–45 μmol L⁻¹ with a correlation coefficient of 0.9988, and the detection limit was 0.10 μmol L⁻¹. The relative standard deviation of the results was 3.4% for six successive determinations of a 20 μmol L⁻¹ Pb(II) solution. A study of interfering substances was also performed. The method was applied to the determination of Pb(II) in water samples with satisfactory results. Correspondence: Hong Qun Luo, School of Chemistry and Chemical Engineering, Southwest University, 400715 Chongqing, China