Dynamic birefringence in solutions of poly (naphthoyleneimide benzimidazole) in different stages of hydrolytic thermal degradation

Flow birefringence (FB) has been investigated in solutions of products of hydrolytic degradation of poly(naphthoyleneimide benzimidazole) (PNIB) in 96% sulphuric acid PNIB solutions have previously been subjected to heating at various temperatures from 65 to 120°C and then investigated at 22°C by FB and viscometry. A monotonic decrease in intrinsic viscosity and the molecular weightM of thermal degradation products with increasing degradation temperature was detected. At the same time, the shear optical coefficients in series of products with decreasingM first increases and then, at treatment temperatures exceeding 90°C, decreases with decreasing [ν] in accordance with decreasingM of the product. Possible reasons for the detected anomaly have been discussed.     

Synthesis and physicochemical studies of ferrocene‐containing materials

Low‐temperature solution‐phase polycondensation of 1,1′‐ferrocenedicarboxylic acid chloride with newly synthesized aromatic diamines was carried out in tetrahydrofuran in the presence of triethylamine to form several new organometallic aromatic polyamides containing ferrocene units. The organometallic aromatic polyamides derived were in good yields ranging from 75 to 80%, amorphous with melting temperatures of > 350 °C. The monomers and the resulting polymers were characterized by their physical properties, elemental analysis, 1 H NMR and FTIR spectroscopy. The differential scanning calorimetry and thermogravimetric studies of the resulting aramids were also carried out. All the polymers were insoluble in common organic solvents. However, all dissolved in concentrated H₂SO₄ forming reddish brown solutions. Their glass transition temperatures were quite high, which is characteristic of aramids. They were also stable up to 450 °C with 10% mass losses (14–23%) recorded in the range 400–470 °C. The activation energies for decomposition of each aramid were also calculated using the Horowitz and Metzger method. All polymers showed reduced solution viscosities in concentrated sulphuric acid, which may be attributed to non‐Newtonian behavior. Copyright © 2007 John Wiley & Sons, Ltd.     

Gas chromatography of manganese(II) and manganese(III) trifluoroacetylacetonates by the ligand vapour technique

The thermal properties and gas Chromatographie behaviour of manganese(II) and manganese(III) trifluoroacetylacetonates (TFA) were investigated by using the ligand vapour technique. The two chelates, Mn(TFA); and Mn(TFA)₃, can be quantitatively eluted on a mixed-liquid phase (1.9% OV-17 ÷ 0.1% PEG-20M) at column temperatures above 210°C and 130–150°C, respectively; Mn(TFA)₃ is completely converted to Mn(TFA)₂ by thermal dissociation at column temperatures above 180°C and completely eluted as Mn(TFA)₂ above 210°C. The chelates can be determined separately within errors of about 1% after a preliminary extraction.     

New polymer syntheses 16. LC-copolyesters of 3-(4-hydroxyphenyl) propionic acid and 4-hydroxy benzoic acids

The polycondensation of 3-(4-hydroxy phenyl)-propionic acid, 4-Hypp, by means of acetanhydride or acetylchloride was conducted either in the presence or in the absence of a liquid reaction medium. DSC measurements, polarizing microscope, and X-ray diffraction studies indicate poly(4-Hypp) possesses at about 215°C a reversible first order transition between two solid phases. Copolyesters containing various mole ratios of 4-Hypp and 4-hydroxy benzoic acid, 4-Hybe, were prepared by bulk condensation with acetanhydride at 320°C. At 4-Hypp/4-Hybe ratios less than 1.0:1.5 the reaction product was heterogeneous, containing crystals of pure poly(4-Hybe). Neither increasing the reaction time nor the variation of the transesterification catalyst resulted in an entirely homogeneous copolyester. However, for 4-Hypp/4-Hybe ratios greater than 1.0:1.5, ¹³C NMR spectra indicate perfectly random sequences. Also, terpolyesters containing 3-chloro-4-hydroxy- or 3,5-dichloro-4-hydroxy-benzoic acid were heterogeneous with less than 30 mol % 4-Hypp. DSC measurements revealed for all polyesters a glass transition in the range of 55–78°C. Temperature dependent X-ray diffraction studies confirm that the solid phase is a s.c. LC-glss. Correspondingly low heat distortion temperatures were found by thermomechanical analyses. The copolyesters display under the polarizing microscope LC-phase up to temperatures of 450–480°C, where rapid thermal degradation prevents further investigations. In the case of the 4-Hypp/4-Hybe 1:1 copolyester, the LC-phase extends over a temperature range of about 400°C. TGA measurements indicate beginning thermal degradation at temperatures between 350 and 380°C.     

Synthesis and Characterization of High Performance Poly(amide-imide)s based on a New Diimide-diacide and Various Diamines

A new diimide-diacid, (4-(4-(2,6-diphenylpyridin-4yl)phenoxy)phenyl)-1,3-bis(trimellitimidobenzene) (PPMIB), was synthesized from the condensation reaction of a new diamine, (4-(4-(2,6-diphenylpyridin-4yl)phenoxy)phenyl)-3,5-diaminobezamide (PPDA), and trimellitic anhydride carboxylic acid (TMAA) in glacial acetic acid. The diimide-diacid (PPMIB) was characterized by FT-IR, ¹H-NMR and elemental analysis. A series of novel aromatic poly(amide-imide)s (PAIs) was synthesized by using direct polycondensation of PPMIB with various diamines in NMP in the presence of triphenylposphite and pyridine as condensing agents. The resulting PAIs were amorphous, readily soluble in many polar aprotic solvents and showed inherent viscosities of 0.35–0.50 dL/g. According to thermal analysis, these polymers exhibited glass transition temperatures (T_gs) in the range of 202–280°C and temperature of 10% weight loss (T₁₀) varied from 400 to 545°C in N₂. These polymers in NMP solution exhibited strong UV-Vis absorption maxima at 320°C nm and their fluorescence emission peaks appeared around 410–565 nm.     

Solvent-free polycondensation of 1,3-bis(hydroxyphenylmethyl)benzene. II. The dramatic difference in the polymerization behavior between meso and racemic isomers

The meso and racemic forms of 1,3-bis(hydroxyphenylmethyl)benzene underwent solvent-free polycondensation with the aid of an acid catalyst giving polyether. Very interestingly, the diastereoisomerism caused a considerable difference in the polymerization behavior. The meso isomer (mp = 96–98 °C) was polymerized even at 65 °C, whereas the racemic one (mp = 158–160 °C) required heating at 100 °C to undergo polymerization. However, the latter produced a much higher molecular weight than the former (30,000 vs 4000). The contamination of the meso isomer with the racemic one very sensitively reduced the polymerization temperature: the 98.5% meso monomer underwent polymerization at 50 °C. In contrast to solvent-free polymerization, two diastereomeric monomers showed almost identical behavior in solution polymerization. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3564–3571, 2003     

Facile Synthesis of Processable Semi-aromatic Polyamide Containing Thioether Units

A series of processable semi-aromatic polyamides containing thioether units have been developed. They were synthesized through the reaction of 4,4’-bis(4-chloroformylphenylthio)benzene (BPB-DC) and aliphatic diamine by the method of interfacial polycondensation. These polyamides had excellent thermal properties with glass transition temperatures (T_g) of 124–137.9°C, melting temperatures (T_m) of 306.4–324.1°C and initial degradation temperatures (T_d) of 409.5–437°C. They had wider processing windows than traditional semi-aromatic polyamides and can be processed by the melting method. They had better tensile strengths of 61.2–73.7 MPa, low-temperature mechanical properties, low water absorption of 0.17%–0.23%, low dielectric constants of 3.47–3.66 at 100 kHz and better melt flowability properties of 37.3 to 164.4 Pa. s, 48.2 to 281.7 Pa. s and 58.3 to 486.7 Pa. s at different shear rates, respectively. Additionally, these polyamides showed good corrosion resistance, they did not dissolve in solvents such as NMP, DMSO, hydrochloric acid (6 mol/L), H₃PO₄ and solution of NaOH (1 mol/L) etc.     

An unusual reaction polymerization in nitric acid medium

We are investigating an unusual reaction that occurs when methyl methacrylate (MMA) is kept in contact with concentrated nitric acid¹ (65% HNO₃, sp. gr. 1.41). Polymer of high molecular weight is formed, showing about one unit of methacrylic acid (MAA) per unit of MMA, when equilibrium is reached. The reaction depends on the temperature, the molar ratio MMA:HNO₃, and the reaction time. Although we also found polymer at temperatures in the range 50–70°C,² in this paper we only report the results when the temperature was kept between 25 and 40°C. Methacrylic acid (MAA) was found to homopolymerize under those mild conditions; its behavior was investigated. Although we also observed that polymer is formed with sulfuric acid (96%) and that acrylic acid polymerizes with both nitric and sulfuric acid at 20–30°C, we are limiting this article to the observed polymerizing action of nitric acid on methyl methacrylate and on methacrylic acid. Work proceeds on this matter in this laboratory.     

Rigid-Rod benzobisthiazole polymers with reactive fluorene moieties: Synthesis and characterization

High purity 2,7-fluorenedicarboxylic acid chloride was synthesized in a multistep reaction scheme from 2,7-dibromofluorene. Subsequent polycondensation in polyphosphoric acid of 2,5-diamino-1,4-benzenedithiol dihydrochloride with terephthaloyl chloride and 2,7-fluorenedicarboxylic acid chloride led to rigid-rod benzobisthiazole polymers with reactive fluorene moieties. The proportion of fluorene in the resultant polymers was controlled through reaction stoichiometry. Soluble polymers with intrinsic viscosities as high as 33.7 dL/g (methanesulfonic acid, 30°C) were obtained if the polymerization temperature was not allowed to exceed 165°C. Insoluble, presumably crosslinked polymers were obtained at higher temperature (190–200°C). Thermal characterization of the polymers by differential thermal analysis and thermal gravimetric analysis/mass spectroscopy did not disclose any thermal transition to 450°C. Onset of weight loss in air did not occur until over 550°C.     

Optically high transparency and light color of organosoluble fluorinated polyamides with bulky xanthene pendent groups

New fluorinated polyamides were prepared directly from a diamine, 9,9‐bis[4‐(2‐trifluoromethyl‐4‐aminophenoxy)phenyl]xanthene ( BTFAPX ) with various aromatic dicarboxylic acid chlorides by low‐temperature polycondensation. The polymers were produced with moderate‐to‐high inherent viscosities of 0.65–1.01 dl/g while the weight‐average molecular weight and number‐average molecular weight were in the range of 69,000–82,000 and 39,000–43,000, respectively. Nearly all the polymers were readily soluble in amide‐type polar aprotic solvents [e.g. N, N‐dimethylacetamide (DMAc) and N‐methyl‐2‐pyrrolidinone], and even in less polar solvents such as dimethyl sulfoxide and pyridine, and afforded transparent, light‐colored, and flexible films upon casting from DMAc solvent. The polymers showed glass transition temperatures between 235 and 284°C, and 10% weight loss temperatures ranging from 495 to 532°C and 476 to 510°C in nitrogen and air, respectively, and char yields higher than 55% at 800°C in nitrogen. All polymers were amorphous and their films exhibited tensile strengths of 64–95 MPa, elongations at break of 6–9%, and tensile moduli of 1.9–2.5 GPa. These polymers had dielectric constants ranging from 3.65 to 4.03 (100 Hz), low‐moisture absorption in the range of 0.56–1.14%, and high transparency with an ultraviolet–visible absorption cut‐off wavelength in the 334–372 nm range. Copyright © 2010 John Wiley & Sons, Ltd.     

Effect of Polycondensation Reaction Conditions on the Properties of Thermotropic Liquid‐Crystalline Copolyester

In this study a range of wholly aromatic copolyesters based on kink m‐acetoxybenzoic acid (m‐ABA) monomer (33 mol%) and equimolar‐linear p‐acetoxybenzoic acid (p‐ABA), hydroquinone diacetate (HQDA) and terephthalic acid (TPA) monomers (67 mol%) have been synthesized by melt polycondensation reaction process at 280°C and 260°C for different time intervals. Characterization of copolyesters were performed by solution viscosity measurement, wide–angle X‐ray diffraction (WAXD), differential scanning calorimetry (DSC), hot‐stage polarized light microscopy, proton‐nuclear magnetic resonance analysis (¹H‐NMR). According to the results obtained, copolyesters showed thermotropic liquid crystalline behavior in an appropriate temperature range. The copolyesters were prepared in high yields. It was observed that the intrinsic viscosities of the copolyesters are increased regularly with increasing polymerization time and temperature. All the copolyesters were soluble in a trifluoroacetic acid/dichloromethane (30:70 v/v) except the copolyesters which were synthesized at 280°C in 5 h. According to the WAXD results; the degree of crystallinity of copolyesters were found to be between 5–15%. DSC and hot stage polarized light microscopy results showed that all the copolyesters are melt processable and a significant molecular interaction exist in a very broad temperature range (160°C and 165°C) in the nematic mesophase. The T_g values are increased with an increasing polycondensation reaction time and temperature and they were observed between 93–126°C. Fibers prepared by a hand‐spinning technique from the polymer melt exhibit well‐developed fibrillar structure parallel to the fiber axis.     

Study on the condensation and crosslinking reactions of furfuryl alcohol and tris(2-hy-droxyethyl)isocyanurate by thermal methods

Condensation and crosslinking reactions of furfuryl alcohol (FA) and FA with tris (2-hydroxyethyl )isocyanurate (THEIC) are studied by means of DSC, TG, TBA, NMR and elemental analysis. Four exothermic peaks are observed on the DSC curves of thermal condensation of FA and FA with THEIC in the presence of sulfuric acid. The peaks I, II (50–80°C), III (110–130°C) and IV (150–190°C) correspond to linear polycondensation of FA through head-to-tail condensation, head-to-head etherification, crosslinking dehydration reaction between methylene group and terminal hydroxy group of FA polymeric chain and to further crosslinking reaction at higher temperature, respectively. The reactivity of FA and THEIC increases sharply at 130–150°C and THEIC is reacted completely at 150°C. Addition of THEIC raises the initial decomposition temperature of FA polymer by 60°C.     

SYNTHESIS AND CHARACTERISTICS OF NOVEL POLYAMIDES HAVING PENDENT N-PHENYL IMIDE GROUPS

We have investigated a novel monomer having a pendent phenyl imide group for preparing new cycloaliphatic-aromatic polyamides. Novel polyamides were synthesized by a direct polycondensation reaction of N-phenyl-2,3-imide cyclopentane-1,4-dicarboxylic acid (PCPA) and various aromatic diamines. A direct polycondensation was carried out by a Yamazaki's direct polycondensation that is typical of using triphenyl phosphite, lithium chloride, and pyridine. Inherent viscosity of these resulting polyamides was in the range 0.47–1.05 dL/g. The glass transition temperatures of these polyamides were in the range of 190–200°C. The decomposition temperatures of them were in the range of 310–323°C in nitrogen atmosphere. The Solubility of these polyamides are good in aprotic solvents such as DMAc (N,N-Dimethylacetamide), NMP (N-Methyl-2-Pyrrolidinone) and DMF (N,N-Dimethylformamide). Transparent, flexible, and tough films were cast from DMAc solutions.     

Synthesis and characterization of poly(aryl ether sulfonate)s with fluorinated phenyl-radicals in the side chain

A series of novel poly(aryl ether sulfone)s (PAESs) were prepared from bis(4-chlorophenyl) sulfone and various bisphenol monomers via nucleophilic aromatic substitution polycondensation. The polycondensation proceeded quantitatively in N,N-dimethylacetamide and afforded PAESs with inherent viscosities of 0.62–0.81 dL/g. The obtained PAESs showed high-glass transition temperatures beyond 177°C and excellent thermal stability with 10% weight loss temperatures in the range of 541–571°C. The PAESs 2a–c could dissolve readily in common organic solvents and their solubility was improved by the introduction of bulky pendant groups. The PAESs formed transparent, strong and flexible films, with tensile strengths of 88.1–98.7 MPa, Young modulus of 3.14–3.52 GPa, and elongation at break of 18–34%. Furthermore, the resulting PAES films showed low dielectric constants (2.77–3.02 at 1 MHz) and low water absorption (0.51–0.83%).     

Reversed-phase high-performance liquid chromatography of protamines

The protamines from the gonads of the sturgeonAcipenser stellatus have been separated by high-performance liquid chromatography. The proteins were eluted with mixtures of water and ethanol having a gradient of ethanol concentrations in the presence of trifluoroacetic acid (TFA). The influence of the concentration of TFA and the temperature of the column on separation was studied. The quantitative (95–98%) isolation of the protamines from the column was achieved at a temperature of 30°C and a 0.15% concentration of TFA.     

Synthesis and characterization of biodegradable polyesteramides constructed mainly by alternating diesterdiamide units from N,N′-bis(2-hydroxyethyl)-adipamide and diacids

Two kinds of aliphatic alternating polyesteramide prepolymers were prepared through melt polycondensation from N,N’-bis(2-hydroxyethyl)-adipamide and adipic acid or sebacic acid. Chain extension of them was conducted with 2,2′-(1,4-phenylene)-bis(2-oxazoline) and adipoyl biscaprolactamate as combined chain extenders. The chain extended polyesteramides (ExtPEAs) were characterized by IR, 1 H-NMR, differential scanning calorimetry, thermogravimetric analysis, wide angle X-ray scattering, tensile test and enzymatic degradation. The results showed that the ExtPEA(4,m)s were mainly constituted with the diester adipamide alternating units. ExtPEA(4,4) and ExtPEA(4,8) had Tm of 83.8℃ and 85.8℃ and initial decomposition temperature above 310.0℃. They crystallized similarly as Nylon-66 did and were flexible thermoplastic materials with tensile strength up to 25.64 MPa and strain at break up to 737%.     

Synthesis of aromatic polyamide-phthalimidines from chloroformylphthalides and aromatic diamines

New polymer-forming monomers, 3-benzylidene-5-chloroformylphthalide and 3-benzylidene-6-chloroformylphthalide, were synthesized by the Perkin reaction of trimellitic anhydride with phenylacetic acid, followed by chlorination. The polycondensation of these monomers with aromatic diamines in N-methyl-2-pyrrolidone at 200°C afforded aromatic polyamide-phthalimidines having inherent viscosities of 0.2-0.5 dL/g. All the polymers were readily soluble in m-cresol, pyridine, dimethylformamide, and dimethyl sulfoxide. Glass transition temperatures of some of the polymers were in the range of 255–282°C. The polyamide-phthalimidines began to lose weight at around 300°C in both air and nitrogen atmospheres, with 10% weight losses being recorded at 435–475°C in nitrogen by thermogravimetry.     

Synthesis and characterization of polyesteramides derived from an oxazoline-functional alcohol and dicarboxylic acid anhydrides

Novel polyesteramides were synthesized by copolymerization in bulk of 5-(4,5-dihydro-1,3-oxazol-2-yl)-1-pentanol and various cyclic dicarboxylic acid anhydrides at temperatures varying between 120 and 200°C. The polymers resulting from polycondensation were characterized by means of ¹H–NMR, FTIR, MALDI–TOF–MS, SEC, and DSC. The glass transition temperatures, T_g, of the copolymers were varied between −28 and +31°C as a function of the anhydride type. Molecular weights, M_w, were dependent on reaction temperature, reaction time, and anhydride type. Spectroscopic investigation of reaction products and esteramide model compounds provided evidence for imide by-product formation, which accounts for the low degree of polymerization. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3367–3376, 1999     

Synthesis and characterization of novel aromatic polyamides containing 3-trifluoromethyl-substituted triphenylamine

A new 3-trifluoromethyl-substituted triphenylamine-containing aromatic diacid monomer, N,N-bis(4-carboxyphenyl)-3-trifluoromethylaniline, was prepared by the substitution reaction of 3-trifluoromethylaniline with 4-fluorobenzonitrile, followed by alkaline hydrolysis of the dinitrile intermediate. Novel aromatic polyamides with 3-trifluoromethyl-substituted triphenylamine moieties were prepared from the diacid and various aromatic diamines via the direct phosphorylation polycondensation. All the polyamides were amorphous and readily soluble in many polar organic solvents such as N,N-dimethylacetamide and N-methyl-2-pyrrolidone, and could be solution-cast into transparent, tough, and flexible films with good mechanical properties. They exhibited good thermal stability with relatively high glass-transition temperatures (258–327°C), 10% weight-loss temperatures above 500°C, and char yields higher than 60% at 800°C in nitrogen. These polymers had low dielectric constants of 3.22–3.70 (100 Hz), low moisture absorption in the range of 1.75–2.58%, and high transparency with an ultraviolet–visible absorption cut-off wavelength in the 375–395 nm range. Cyclic voltammograms of the polyamide films cast onto an indium tin oxide coated glass substrate exhibited a reversible oxidation redox couple with oxidation half-wave potentials (E_1/2) of 0.95–1.00 V vs. Ag/AgCl in an acetonitrile solution.     

Stability of NF membranes under extreme acidic conditions

Two commercial nanofiltration (NF) membranes (FilmTec NF-45 and Desal-5 DK) and two new NF-1 membranes made by BPT (Bio Pure Technology) for the purpose of a European Union funded research project (RENOMEM) were tested under extreme acidic conditions. The polyethersulphone (PES) ultrafiltration (UF) supports used for casting the BPT-NF-1 membranes were also tested under similar conditions. The 006 and 015 UF supports were found to be stable in 5% nitric acid at 20 and 80 °C for 4 and 3 months, respectively. Both supports (006 and 015) showed a significant reduction in flux after immersion in sulphuric acid at both temperatures. The BPT-NF-1 membranes showed excellent resistance to 20% sulphuric acid for up to 4 months at 20 °C but were attacked by the nitric acid solution. The resistance of the two commercial membranes in 20% sulphuric acid at 20 °C was generally lower than that of the BPT-NF-1 membranes. The NF-45 membrane was slightly more stable in 5% nitric acid at 20 °C. Degradation of the membrane occurred only after 2 months while both the Desal-5 DK and BPT-NF-1 membranes degraded during the first month. At the higher temperature of 80 °C in 5% nitric acid all membranes degraded in the first month.The cause of membrane degradation was attributed to oxidation of the thin NF selective skin layer in nitric acid and to acid-catalysed hydrolysis of this layer in sulphuric acid. Knowing the cause of membrane degradation is a step forward in developing a better and more stable nanofiltration membrane.