The structure of MDI/BDO-based polyurethanes: Diffraction studies on model compounds and oriented thin films

Polyurethanes based on MDI/BDO are known to crystallize in three distinct forms. Two of these crystal structures, type II and type III, have been characterized by electron and x-ray diffraction experiments on model compounds and oriented thin films of a 77% hard-segment polyurethane elastomer. The model compounds were of the form BDO(MDI/BDO)_n with n = 1, 2, 3. Results from the model compounds indicate that the MDI/BDO repeat crystallizes in the type-II structure, which has a contracted conformation with a monomer repeat length of 1.70 nm. MDI/BDO-based polyurethanes also exhibit the type-II structure under quiescent crystallization conditions. Studies of oriented thin films of an MDI/BDO-based polyurethane indicate that a change in crystal form occurs on stretching to the fully extended monomer conformation. This crystal form is termed type III and has a monomer repeat length of 1.92 nm.     

1,5-萘二异氰酸酯与1,4-丁二醇基为基质的多嵌段聚氨酯弹性体的合成与性能

利用 1 ,5_萘二异氰酸酯 (NDI)和 1 ,4_丁二醇 (BDO)为均匀硬质分子单体 ,与不同软质分子单体 (聚醚、聚酯、聚硅氧烷 )缩合制备多嵌段聚氨酯弹性体 ,详细研究了硬嵌段相 (NDI)弹性体的结构与性能间的关系 ,发现随着硬嵌段相长度的增加 ,或者氨基甲酸酯中胺基与聚醚、聚酯、聚硅氧烷中软段氧原子间氢键的减弱 ,都导致微相分离程度的增加 ,造成聚合物熔点和熔化热的升高。硬嵌段相熔化的多峰行为是由于形成了NDI/BDO半微晶区 ,在退火时转变为更加有序的结晶微区 ,当温度高于 1 80℃时 ,由于氢键的断裂 ,NDI/BDO硬嵌段发生分解反应 ,该过程源于不很有序的硬嵌段半结晶微区。当温度高于 2 5 0℃时 ,发生快速的分解。在动态力学行为方面 ,NDI基聚醚弹性体比其它硅氧烷基的弹性体展示了更高的硬嵌段区的稳定性 ,同时 ,在使用温度范围内 ,也显示出最高的储能模量值 ,表明刚性对温度的依赖性 ,以及NDI/BDO硬嵌段中活性填料的显著影响     

主链型液晶聚硅氧烷聚氨酯的合成及性质

合成了主链型联苯类及氧化偶氯苯类液晶聚硅氧烷聚氨酯弹性体，采用红外光谱，示差扫描量热，动态粘弹谱及带热台偏光显微镜等方法对聚合物进行了表征，讨论了它们的结构与性能．研究结果表明，这一系列多嵌段聚氨酯多数是向列型的液晶高分子聚合物，液晶相的形成同嵌段聚氨酯样品的软硬段相互作用有着密切的联系     

Structure of the hard segments in trans,trans-diisocyanato dicyclohexylmethane based PU elastomers

A model for the structure of the hard segments and the hydrogen bonded network in the hard domains of segmented polyurethane elastomers with trans,trans-diisocyanato dicyclohexylmethane (tt-HMDI)/1,4-butanediol (BDO) based hard segments is proposed. The structure of the bis(methylurethane) oftt-HMDI (Me-ttHMDI-Me) has been determined by single crystal x-ray diffraction analysis and the conformation and packing of the polyurethane hard segments are constructed by connecting the successive Me-ttHMDI-Me units via –CH₂–CH₂– groups using the principle of isomorphic substitution. The conformation and hydrogen bonds of the monomer units are retained. The resulting polyurethane structure is highly crosslinked by a three-dimensional hydrogen bond network. The special packing principle may explain the high melting point as compared to the well-known structure of 4,4-diisocyanato diphenylmethane (MDI)-BDO hard segments and the differences in the material properties.     

Hard-segment domain sizes in MDI/diol polyurethane elastomers

Wide-angle x-ray line broadening methods have been used to determine the crystallite size and degree of distortion for the crystalline hard domains in MDI/diol polyurethane elastomers. Crystallite widths have been determined from the integral breadths of the 00l reflections following correction for distortions of the second kind according to the method Hosemann for polymers prepared using ethylene glycol, propandiol, butandiol, and hexandiol as the chain extender. These data relate to the width of the crystallites along the chain axis and thus can be interpreted in terms of the morphology of the hard domains. The crystallite sizes increase and the distortions decrease with increasing elongation and annealing time, and the sizes tend toward asymptotic values which correspond approximately to the average lengths of the hard-segment chains. These results rule out any appreciable folding of the hard-segment chains and point to a model for the hard domains formed by lateral aggregation of extended hard segments.     

Synthesis and Characterization of Thermoplastic Polyurethaneureas based on Polyisobutylene and Poly(tetramethylene oxide) Segments

New thermoplastic polyurethaneureas (TPUU) based on polyisobutylene (PIB) and poly(tetramethylene oxide) (PTMO) segments have been synthesized possessing tensile properties comparable to conventional PTMO based TPUs. PIB based TPUU containing 35 weight (wt)% hard segment was synthesized by chain extension of H₂N-Allyl-PIB-Allyl-NH₂ with 4,4′ -methylene bis(phenylisocyanate) (MDI) and 1,4-butanediol (BDO) in toluene. The ultimate tensile strength (UTS) = 12 MPa and ultimate elongation = 70% were inferior to PTMO based polyurethane (UTS = 35 MPa, elongation at break = 600%). H₂N-Allyl-PIB-Allyl-NH₂ and HO-PTMO-OH in different proportions were chain extended in presence of MDI and BDO to obtain TPUUs containing 35 wt% hard segment. The polymers exhibited M _ns = 84000–138000 with polydispersity indices (PDIs) = 1.7–3.7. The UTS = 23–32 MPa and elongation at break = 250–675% was comparable to that of PTMO based polyurethane and significantly higher than the PIB based TPUU with the same Shore hardness. The Young's modulus of the polymers was strongly dependent and directly proportional to the PIB wt% in the SS of the TPUUs.     

端羟基芳香酯二醇扩链的聚氨酯－酯的DSC研究

端羟基芳香酯二醇扩链的聚氨酯－酯的ＤＳＣ研究陈静，余学海，杨昌正（南京化工学院应化系南京２１０００９）（南京大学化学系南京２１００９３）关键词嵌段聚醚聚氨酯－酯，结晶性，微观相结构，差示扫描量热法，形态结构众所周知，聚氨酯嵌段共聚物是一类结构特殊、用...     

端羟基芳香酯二醇扩链的聚氨酯－酯的DSC研究

端羟基芳香酯二醇扩链的聚氨酯－酯的ＤＳＣ研究陈静，余学海，杨昌正（南京化工学院应化系南京２１０００９）（南京大学化学系南京２１００９３）关键词嵌段聚醚聚氨酯－酯，结晶性，微观相结构，差示扫描量热法，形态结构众所周知，聚氨酯嵌段共聚物是一类结构特殊、用...     

Polydimethylsiloxane–polyurethane elastomers: Synthesis and properties of segmented copolymers and related zwitterionomers

A series of polyurethane block polymers based on hydroxybutyl-terminated polydimethyl-siloxane soft segments of molecular weight 2000 were synthesized. The hard segments consisted of 4,4′-methylenediphenylene diisocyanate (MDI) which was chain extended with either 1,4-butanediol (BD) or N-methyldiethanolamine (MDEA). The MDEA-extended materials were ionized by using 1,3-propane sultone. The weight fraction of hard segments was in the range 0.13–0.39. The morphology and properties of these polyurethane elastomers were studied by a variety of techniques. All of these short-segment block copolymers showed nearly complete phase separation. The zwitterionomer materials exhibited ionic aggregation within the hard domains. Hard-segment crystallinity or ionic aggregation did not affect the morphology. Hard-domain cohesion was found to be a more important factor than hard-domain volume fraction in determining the tensile and viscoelastic properties of these elastomers.     

交联密度对脂肪族聚氨酯弹性体结构与性能的影响

采用异佛尔酮二异氰酸酯(IPDI)与聚醚二元醇、三羟甲基丙烷(TMP)和1,4-丁二醇反应制备了具有不同交联密度的脂肪族聚氨酯弹性体.研究结果表明,当聚氨酯弹性体的硬段含量为40 wt%时,随着TMP含量的增加,聚氨酯弹性体的交联密度线性增加.随着聚氨酯弹性体交联密度的提高,聚氨酯中硬段相的玻璃化转变温度由32℃降为2...     

多元醇对对苯二异氰酸酯基聚氨酯微孔弹性体的形态与性能影响

以对苯二异氰酸酯(PPDI)、1,4-丁二醇、水、聚四氢呋喃醚多元醇(PTMEG)和氢化端羟基丁二烯多元醇(HLBH)为原料,采用两步法制备出聚氨酯微孔弹性体样品。通过傅里叶变换衰减全反射红外光谱(FTIR-ATR)、动态机械分析(DMA)、差示扫描量热仪(DSC)、万能材料试验机等技术手段对样品的微相分离、耐低温性能、动态生热进行了系统表征。结果表明,两种多元醇结构对泡孔尺寸影响不大,微孔尺寸在100~300μm之间,其中以150μm尺寸左右的泡孔居多;HLBH制备的聚氨酯微孔弹性体硬段形成的氢键数量多于PTMEG制备的微孔弹性体,具有更好的微相分离;由于较好的微相分离结构,HLBH样品在-30~150℃具有很宽的模量平台区,而PTMEG样品受软段的低温结晶影响,在0℃以下模量急剧上升,HLBH样品低温下的刚度变化优于PTMEG样品;同时HLBH样品的滞后生热亦小于PTMEG样品,具有更好的动态疲劳性能。     

聚氨酯硬链段球晶生长与软硬链锻混容性的关系

线型可溶性聚氨酯的硬链段结晶难以长成球晶 ,然而本实验室已经证明即使从熔体结晶硬链段也是能够长成球晶的 .研究了聚酯与聚醚型聚氨酯硬链段长球晶的规律 ,并发现聚氨酯硬链段长球晶的难易与聚氨酯软硬链段混容性密切相关 .动态力学分析 (DMA)与示差扫描量热 (DSC)实验表明聚ε 已内酯 (PCL)、聚已二酸丁二醇酯 (PTMA)、聚四氢呋喃 (PTMO)及聚环氧丙烷 (PPO)型聚氨酯的软硬链段混容性从前至后递减 .从熔体退火结晶时 ,聚氨酯硬链段长成球晶的退火温度范围是有限的 ,软硬链段混容性越好 ,聚氨酯硬链段能长成球晶的温度范围越窄 ,所需长的时间越长 .聚氨酯硬链段长球晶的下限温度取决于软硬链段间所存在的氢键作用 ,聚氨酯硬链段长球晶的上限温度与软硬链段混容性直接相关 .     

Polar/nonpolar gas transfer through PEO-based copolymers membranes

Two PEG-based copolymers containing two different chain extenders, as hard segments, were synthesized by 4,4′-methylenediphenyl diisocyanate (MDI). The chain extenders were 1,4-butane diol (BDO) and 1,2-ethane diamine (EDA). The application of the polyurethane (PU) and poly(urethane-urea)s (PUU)s synthesized polymers, which were characterized by Fourier transform infrared spectrometer (FTIR), differential scanning calorimetry (DSC) and atomic Force Microscopy (AFM), in the gas permeability was investigated. The obtained results indicated that by replacing the urea linkage in the polymers, the microphase separation of hard and soft segments increased. The synthesized PEG-based copolymers were semi-crystalline at room temperature. According to the DSC results, the crystallinity of the synthesized polyurethanes decreased as temperature increased. In addition, a reduction in mean surface roughness could be seen based AMF information. The gas (carbon dioxide and methane) separation properties of the polymers revealed that by replacing the urea linkage, the diffusivity, permeability and selectivity of the gases increased slightly.

The solubility and diffusivity of gases indicated he solubility domination of gas transport in these membranes. However, the sorption coefficient (S) of a particular gas was surprisingly constant for the two synthesized polymers. The CO₂ permeability increased with increasing feed pressure, while CH₄ permeability remained almost constant at both temperatures of 25°C and 35°C. The increase in temperature led to an increase in the permeability of the gases and a decrease in the gas selectivity for the both synthesized polyurethanes.     

Nonclassical Urea Oligomers. VII. Binding Specificity of Carbanilido-ethylenimine Oligomer: Absorption Behavior in Suspension

Polyester elastomers were prepared by block copolymerization of dimethyl terephthalate (DMT), butanediol (BDO), and polytetramethylene glycol (PTMG). Polyester from DMT and butanediol forms a high-melting hard segment in block copolyester to prevent undue chain slippage when fibers are stretched. High elongation was provided by soft segment which consisted of condensation product from DMT and PTMG.

Experiments were carried out to determine the effect of composition variables on the properties of these elastomers, such as glass transition temperature, elongation at break, tenacity, and elastic recovery. The study on molecular characteristics of the elastic polyester showed that a leather-like region exists between glassy and rubbery regions. These elastomers were melt-spun to give elastic fibers which are competitive with commercially available Spandex-type fibers.     

Control of hard segment size in polyurethane formation

In general, segmented polyurethane elastomers are prepared by reacting an isocyanate-capped polyol prepolymer with a short-chain diol chain extender, yielding an elastomer with hard segments of uniform size. However, the hard segment size will not be uniform if the polyurethane polymer is prepared by forming the hard segment first, followed by soft segment formation. Because the mechanical properties of polyurethane elastomers depend on the relative ratio of the hard to soft segments as well as the effectiveness of the hard segment as a physical crosslinker, the control of the size distribution of the hard segment is a key factor in designing polyurethane elastomers. It was found that reaction conditions can affect the size distribution of hard segments derived from an aliphatic diisocyanate with differential reactivity between the two isocyanate groups. Lower reaction temperatures and simultaneous mixing of all reactants gave the preferred size distribution of hard segments. © 1995 John Wiley & Sons, Inc.     

Novel polycarbonate-based polyurethane elastomers: Composition–property relationship

Novel all-aliphatic polycarbonate-based polyurethane (PC-PU) elastomers, as well as PC-PU nanocomposites filled with organic-modified clays were synthesized, characterized and studied. It was found that they have very attractive mechanical properties (e.g., elongation at break between 600% and 800%). The prepared PC-PUs possess a distinctly segmented structure, which is the key prerequisite for their behavior as strong physical rubbery networks. All synthesized materials melt at elevated temperatures (between 110 and 200 °C) and hence can be processed like normal thermoplastics. The dispersion of the clay nanofiller was achieved by its one day swelling in the alcohol and a brief successive stirring. This procedure is very successful and leads to a partial exfoliation of the clay (documented by X-ray diffraction and TEM). The best nanocomposites with very good tensile properties, particularly with significantly increased moduli were obtained using the bentonite nanofiller. The study shows that the nanofiller interacts strongly with the hard domains and influences their melting temperature (DMTA and DSC), but it does not affect the glass transition temperature of soft domains. While Cloisite 15A was found to interact preferentially with the hard domains, the organic modified bentonite shows a strong interaction with both soft and hard segments, behaving as a blending agent. Hard domains in neat matrices, formed by hydrogen bonding of hard segments, were practically invisible by X-ray or TEM, but were successfully detected by AFM. Besides excellent mechanical properties, the prepared elastomers and their nanocomposites showed an interesting phase behavior (which was studied by combining DMTA and modulated DSC).     

SHAPE MEMORY EFFECT OF PU IONOMERS WITH IONIC GROUPS ON HARD-SEGMENTS

SMPU （shape memory polyurethane） non-ionomers and ionomers, synthesized with poly（c-caprolactone） （PCL）, 4, 4＇-diphenylmethane diisocyanate （MDI）, 1,4-butanediol （BDO）, dimethylolpropionic acid （DMPA） were measured with cyclic tensile test and strain recovery test. The relations between the structure and shape memory effect of these two series were studied with respect to the ionic group content and the effect of neutralization. The resulting data indicate that, with the introduction of asymmetrical extender, the stress at 100% elongation is decreased for PU non-ionomer and ionomer series, especially lowered sharply for non-ionomer series; the fixation ratio of ionomer series is not affected obviously by the ionic group content; the total recovery ratio of ionomer series is decreased greatly. After sufficient relaxation time for samples stretched beforehand, the switching temperature is raised slightly, whereas the recovery ratio measured with strain recovery test method is lowered with increased DMPA content. The characterization with FT-IR, DSC, DMA elucidated that, the ordered hard domain of the two series is disrupted with the introduction of DMPA which causes more hard segments to dissolve in soft phase; ionic groups on hard segment enhance the cohesion between hard segments especially at high ionic group content and significantly facilitate the phase separation compared with the corresponding non-ionomer at moderate ionic group content.     

季戊四醇型HTPB-PU弹性体的研究

以端羟基聚丁二烯、液化改性MDI为原料,季戊四醇为扩链剂与交联剂制备季戊四醇型聚氨酯,并用IR、TG、DSC和SEM对其进行表征;研究了影响季戊四醇型聚氨酯的力学性能和热性能的因素。结果表明：随扩链剂用量的增大,季戊四醇型聚氨酯的拉伸强度和硬度增大,而断裂伸长率减小,同时热稳定性得到提高。SEM显示此弹性体中存在明显的相分离。     

Polyisobutylene‐based polyurethanes. III. Polyurethanes containing PIB/PTMO soft co‐segments

The synthesis, characterization, and structure–property behavior of polyurethanes containing polyisobutylene (PIB)/poly(tetramethylene oxide) (PTMO) soft co‐segments and bis(4‐isocyanatocyclohexyl)methane (HMDI)/hexanediol (HDO) hard segments is presented. The mechanical (stress/strain, hardness, and hysteresis) properties of these novel polyurethanes were investigated over a broad composition range. PIB‐based polyurethanes with HMDI/HDO hard segments showed better mechanical properties than earlier polyurethanes containing highly crystalline hard segments. The addition of moderate amounts (20% by weight) of PTMO significantly increased both tensile strengths and elongation. In the presence of larger amounts of PIB, these polyurethanes are expected to possess oxidative/hydrolytic/enzymatic stabilities superior to commercially available polyurethanes. These polyurethanes are softer and exhibit hysteresis superior to or comparable with conventional polyurethanes. According to initial thermal studies, these materials show good melt processibility. Overall, the mechanical properties of PIB based hybrid polyurethanes are similar to commercially important polyurethane type biomaterials. Our results show that the incorporation of PTMO segments to PIB‐based polyurethanes significantly improves elastomeric properties. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5278–5290, 2009     

Synthesis and characterization of novel biodegradable folate conjugated polyurethanes

In order to obtain targeting polyurethane micelle drug carriers, a series of biodegradable folate conjugated polyurethanes (FPUs) were synthesized using poly(ethylene glycol) (PEG) and poly(ε-caprolactone) (PCL) as soft segments, L-lysine ethyl ester diisocyanate (LDI) and 1,3-propanediol (PDO) as hard segments, and folic acid-ethylenediamine conjugate (FA-EDA) as an end-capping reagent. The resultant FPUs were fully characterized by (1)H NMR, Fourier-transform infrared (FTIR) spectroscopy, ultraviolet spectrophotometry (UV), gel permeation chromatography (GPC), and differential scanning calorimetry (DSC). These polymers can self-assemble into micelles in aqueous solutions confirmed by dynamic light scattering (DLS), pyrene fluorescence probe techniques, and transmission electron microscopy (TEM). The results indicated that the bulk structures and micellar properties of the prepared polyurethanes could be controlled by varying the PEG content in the soft segments. The present work provides a facile approach to prepare amphiphilic multiblock copolymers with tumor targeting moiety, which is a good candidate as biodegradable carriers for active intracellular drug delivery.