Surface structure of γ-Alumina-Supported Ruthenium Catalysts for ammonia synthesis

Ruthenium supported catalysts were prepared by impregnation of RuCl₃ · 3 H₂O and K₄[Ru(CN)₆] · 3 H₂O aqueous acetone solutions upon several acid(base)-modified γ-Al₂O₃ samples. Characterization of the catalysts was carried out by CO chemisorption and kinetics of hydrogen reduction, correlating the particle size and dispersion of the metallic phase with the previous acid modification of the γ-Al₂O₃, as well as with the type of precursor and solvent used. The surface properties were also correlated with their catalytic activities for ammonia synthesis at atmospheric pressure and 583 K (N₂/H₂ ? 1/3).     

Surface Structure of γ-Alumina-Supported Iron Catalysts for Ammonia Synthesis

Iron supported catalysts were prepared by impregnation of iron from a K₄[Fe(CN)₆] aqueous solution, upon several acid-modified γ-Al₂O₃ samples. Characterization of the catalysts was carried out by CO chemisorption, temperature programmed reduction (TPR), and kinetics of hydrogen reduction, resulting the particle size and dispersion of the metallic phase dependent on the previous acid modification of the γ-Al₂O₃. The catalytic activity for ammonia synthesis was followed at atmospheric pressure and 593 K (N₂/H₂ = 1/3). Correlations of the surface properties of the catalysts with their method of preparation and catalytic activities are obtained.     

Catalytic properties of Pt/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts in the aqueous-phase reforming of ethylene glycol: Effect of the alumina support

The influence of the alumina support on the catalytic activity of Pt/Al₂O₃ catalysts in aqueous phase reforming of ethylene glycol to hydrogen was studied. The catalysts were prepared by impregnation of γ-, δ-, and α-alumina with H₂PtCl₆. The highest rate of hydrogen production (452 μmol min⁻¹ g⁻¹) obtained with the Pt/α-Al₂O₃ catalyst can be related to the highest extent of dispersion of Pt on α-Al₂O₃. XPS, TEM-EDX and TPR-H₂ measurements showed the absence of chloride-containing surface complexes in the Pt/α-Al₂O₃ catalyst. However, chloride-containing entities were found on the surface of Pt/γ-Al₂O₃ and Pr/δ-Al₂O₃ catalysts. When chloride ions are removed chlorinated Pt species facilitate the sintering of Pt crystallites and in this way affect the extent of Pt dispersion. Moreover, depending upon the particular crystalline form, alumina atoms have different coordination and alumina surfaces contain varying amounts of OH groups of different nature which affect the interaction between Pt and the support.     

贵金属铱对氨分解用镍基催化剂的促进作用研究

用湿式浸渍法制备了不同贵金属质量分数的镍-铱双金属催化剂,以氨分解为模型反应对其催化性能进行考察.结果表明,贵金属铱的添加提高了10%Ni/γ-Al2O3的低温活性.在铱的质量分数不高于1%时,氨分解反应活性随铱质量分数的增加出现最大值(相应的Ir质量分数为0.7%),对应的10%Ni-0.7%Ir/γ-Al2O3催化剂在400 ℃时,氨分解率为43.55%,较单组分的Ni催化剂高40.0%.用H2-TPR、H2-TPD 、BET和XRD表征方法对催化剂进行了表征.结果表明,Ir与活性组分Ni之间存在协同作用.铱的添加促进了活性组分的分散、减小了镍的晶粒尺寸,且增加了催化剂活性位的数量,从而提高了催化剂的氨分解性能.     

TiO2-Al2O3载体的制备方法对其负载的磷化镍催化剂加氢脱氮反应性能的影响

采用共沉淀法和原位溶胶-凝胶法制备了TiO₂-Al₂O₃复合载体,其负载的磷化镍催化剂采用等体积浸渍法和H₂原位还原法制备. 通过N₂吸附（BET）、X射线衍射（XRD）、透射电镜（TEM）、程序升温还原（TPR）,X射线光电子能谱（XPS）和等离子体发射光谱（ICP-AES）表征技术对催化剂进行了表征,并通过喹啉的加氢脱氮反应评价了催化剂的加氢脱氮性能. 结果表明,原位溶胶-凝胶法制成的复合载体基本保留了原有的γ-Al₂O₃的孔特征,具有较大的比表面积和较宽的孔分布,TiO₂主要以表面富集的形式分散在管状的γ-Al₂O₃表面,其负载的磷化镍催化剂还原后所形成的活性相为Ni₂P和Ni₁₂P₅;而共沉淀法制成的复合载体比表面积较小,孔径分布更加集中,TiO₂趋于在块状的Al₂O₃表面均匀分散,其负载的磷化镍催化剂具有更好的可还原性,还原后所形成的活性相为Ni₂P. 不同的载体制备方法和不同的钛铝比对催化剂加氢脱氮性能影响较大,当n（Ti）/n（Al）=1/8时,共沉淀法载体负载的催化剂表现出最佳的加氢脱氮性能,在340 ℃,3 MPa,氢油体积比500,液时空速3 h^-1的反应条件下,喹啉的脱氮率可以达到91.3%.     

Novel Ni/CeO2-Al2O3 composite catalysts synthesized by one-step citric acid complex and their performance in catalytic partial oxidation of methane

A series of novel Ni/CeO2-Al2O3composite catalysts were synthesized by one-step citric acid complex method. The as-synthesized catalysts were characterized by N2physical adsorption/desorption, X-ray diffraction(XRD), Fourier transform infrared(FT-IR) spectroscopy, hydrogen temperature-programmed reduction(H2-TPR), X-ray photoelectron spectroscopy(XPS) and thermogravimetry analysis(TGA). The effects of nickel content, calcination and reaction temperatures, gas hourly space velocity(GHSV) and inert gas dilution of N2on their performance of catalytic partial oxidation of methane(CPOM) were investigated. Catalytic activity test results show that the highest methane conversion(85%), the best selectivities to carbon monoxide(87%) and to hydrogen(95%), the excellent stability and perfect H2/CO ratio(2.0) can be obtained over Ni/CeO2-Al2O3with 8 wt% Ni content calcined at 700 ℃ under the reaction condition of 750 ℃, CH4/O2ratio of 2 : 1 and gas hourly space velocity of 12000 mL h-1 g-1. Characterization results show that the good catalytic performance of this composite catalyst can be contributed to its large specific surface area(～108 m2 g-1), small crystallite size, easy reducibility and low coking rate.     

CH4 reforming with CO2 for syngas production over La2O3 promoted Ni catalysts supported on mesoporous nanostructured γ-Al2O3

Nanostructured γ-Al₂O₃ with high surface area and mesoporous structure was synthesized by sol-gel method and employed as catalyst support for nickel catalysts in methane reforming with carbon dioxide. The prepared samples were characterized by XRD, N₂ adsorption-desorption, TPR, TPO, TPH, NH₃-TPD and SEM techniques. The BET analysis showed a high surface area of 204 m²·g⁻¹ and a narrow pore-size distribution centered at a diameter of 5.5 nm for catalyst support. The BET results revealed that addition of lanthanum oxide to aluminum oxide decreased the specific surface area. In addition, TPR results showed that addition of lanthanum oxide increased the reducibility of nickel catalyst. The catalytic evaluation results showed an increase in methane conversion with increasing lanthanum oxide to 3 mol% and further increase in lanthanum content decreased the catalytic activity. TPO analysis revealed that the coke deposition decreased with increasing lanthanum oxide to 3 mol%. SEM and TPH analyses confirmed the formation of whisker type carbon over the spent catalysts. Addition of steam and O₂ to dry reforming feed increased the methane conversion and led to carbon free operation in combined processes.     

Preparation and catalytic activity for ammonia synthesis of several ruthenium supported catalysts

Ruthenium supported catalysts were prepared from RuCl₃ · 3H₂O and K₄[Ru(CN)₆] · 3 H₂O solutions, upon several acid/base pretreated γ-Al₂O₃ samples, using water and acetone as solvents. Metallic adsorption was found to be dependent on solvent and precursor used. An increasing final ruthenium content of the catalysts with increasing acid site content of the support is observed, when K₄[Ru(CN)₆] · 3 H₂ is used as a precursor. The catalytic activity was followed at atmospheric pressure and 593 K (N₂/H₂ = 1/3). Catalysts prepared from K₄[Ru(CN)₆] · 3 H₂O were about ten fold more active than those prepared from RuCl₃ · 3 H₂O. The catalytic activity of catalysts prepared from K₄[Ru(CN)₆] · 3 H₂O was found to be sensitive to the acid-pretreatment of γ-Al₂O₃, while the activity of those prepared from RuCl₃ · 3 H₂O was not sensitive to the pretreatment of the support.     

镍基催化剂上稻草水蒸气重整制富氢合成气

采用浸渍法制备了SiO₂, γ-Al₂O₃, CaO和TiO₂负载的Ni催化剂, 以及不同MgO含量的MgO-7.5%Ni/γ-Al₂O₃催化剂,利用X射线衍射和N₂吸附-脱附技术表征了催化剂的结构,在固定床反应器上评价了它们在稻草水蒸气催化重整制合成气反应中的催化性能,考察了反应条件对催化剂性能的影响.结果表明, 以γ-Al₂O₃为载体时Ni催化剂活性最高,其中7.5%Ni/γ-Al₂O₃催化剂的H₂收率可达1071.3ml/g,H₂:CO的体积比为1.4:1;同时,MgO的添加进一步提高了该催化剂的性能,当MgO含量为1.0%时,H₂收率可达1194.6ml/g,H₂:CO体积比可达3.9:1.可见MgO的加入促进了Ni基催化剂上稻草水蒸气催化重整制合成气反应的进行,同时使得合成气中CO发生水-汽转换反应,从而大大提高了合成气中H₂含量.     

Improvement of the Mo/TiO2-Al2O3 Catalyst by the Control of the Sol-Gel Synthesis

Traditional hydrotreating catalysts are constituted by molybdenum deposited on Al₂O₃ promoted by nickel and phosphorous. Several studies have shown that TiO₂-Al₂O₃ mixed oxides are excellent supports for the active phases. Results concerning the preparation, characterization and testing of molybdenum catalyst supported on titania-alumina are presented. The support was prepared by sol-gel route using titanium and aluminum isopropoxides, the titanium one chelated with acetylacetone (acac) to promote similar hydrolysis ratio for both the alcoxides. The effect of nominal molar ratio [Ti]/[Ti+Al] on the microstructural features of nanometric particles was analyzed by X-Ray Diffraction, N₂ Adsorption Isotherms and Transmission Electron Microscopy. The catalytic activity of Mo impregnated supports was evaluated using the thiophene hydrodesulfurization at different temperatures and atmospheric pressure. The pores size distribution curve moves from the micropores to the mesopores by increasing the Ti contents, allowing the fine tuning of average size from 2.5 to 6 nm. Maximal (367 m²·g^?1) and minimal (127 m²·g^?1) surface area were found for support containing [Ti]/[Ti+Al] ratio equal to 0.1 and 1, respectively. The good mesopore texture of alumina-titania support with [Ti]/[Ti+Al] molar ratio between 0.3 and 0.5 was found particularly valuable for the preparation of well dispersed MoS₂ active phase, leading to HDS catalyst with somewhat higher activity than that prepared using a commercial alumina support.     

Ce改性的Pt/γ-AlO3催化剂用于富氢气氛下CO选择氧化

研究了Ce改性的Pt/γ-AlO3对于富氢气氛下CO选择氧化反应的催化行为考察了制备条件（共沉积沉淀法、分步沉积沉淀法以及沉积沉淀温度）对催化活性的影响．结果表明，在80℃时用共沉积沉淀方法制备的催化剂Pt/γ-AlO3-CP-80对CO氧化反应表现出良好的活性和选择性，CO转化率在120℃时可以达到85％．利用氢气程序升温还原和原位漫反射红外光谱对不同条件下制备的催化剂进行了表征，分析了Cc的促进作用．     

Deposition of NiO onto MoO3/γ-Al2O3 extrudates by slurry impregnation method

NiO-MoO₃/γ-Al₂O₃ catalysts were prepared by the reaction of γ-Al₂O₃ extrudates with an aqueous slurry of MoO₃, followed by the reaction of the MoO₃/γ-Al₂O₃ catalyst with an aqueous slurry of NiO, Ni(OH)₂, NiCO₃·2Ni(OH)₂·xH₂O, or 2NiCO₃·3Ni(OH)₂·4H₂O and by subsequent drying. The NiO deposition was examined with electron probe microanalysis. The deposited Ni efficiently increased the activity in benzothiophene hydrodesulfurization.     

Role of metal Cu species on methyl laurate catalytic hydrogenation to oxygen-containing compounds

The Cu/γ-Al₂O₃ catalysts with different Cu loadings were prepared by impregnation method. The physicochemical properties of these Cu/γ-Al₂O₃ catalysts were characterized by H₂-TPR, XRD, and in-situ XPS. The catalytic hydrogenation performances of methyl laurate over Cu/γ-Al₂O₃ catalysts were studied. The results show that the hydrogenation performances of methyl laurate on Cu/γ-Al₂O₃ catalyst are related to the dispersion, crystallite size, and content of the active component Cu⁰. The 10CA catalyst has the best hydrogenation performances for methyl laurate to produce C₁₂ alcohol. At 300 °C, the conversion of methyl laurate and the selectivity of C₁₂ alcohol are 55.6% and 30.4%, respectively.     

Mo_2C/γ-Al_2O_3催化剂上苯加氢反应的原位红外光谱研究

采用程序升温反应法制备了钝化态、还原钝化态和新鲜态Mo2C/γ-Al2O3催化剂,结合原位红外光谱表征技术和反应性能评价,考察、比较了三种催化剂苯加氢反应活性.原位红外光谱结果表明,新鲜态Mo2C/γ-Al2O3催化剂在室温就显示了较好的苯加氢反应活性,表现了类贵金属的催化活性.CO吸附在反应前后新鲜态Mo2C/γ-Al2O3催化剂上的对比结果表明,低价态的Mo位(Moδ+(0δ2))是苯加氢反应活性中心.三种催化剂的反应活性结果表明,新鲜态Mo2C/γ-Al2O3催化剂反应活性最好,催化剂寿命最长,失活之后在500°C下H2处理即可恢复原有活性.     

Preparation of bimetallic CoO-MoO3/γ-Al2O3 and NiO-MoO3/γ-Al2O3 hydrodesulfurization catalysts by deposition of Co, Ni and Mo onto α-AlOOH during paste processing

CoO-MoO₃/γ-Al₂O₃ and NiO-MoO₃/γ-Al₂O₃ catalysts were prepared by the reaction of α-boehmite (α-AlOOH) with MoO₃ in an aqueous paste, followed by the reaction of the MoO₃/α-AlOOH catalyst with Co(OH)₂·CoCO₃ or 2NiCO₃·3Ni(OH)₂·4H₂O in an aqueous paste, and by subsequent drying and/or calcination. The deposited MoO₃ functioned as a thermal stabilizer inhibiting the sintering of the Al₂O₃ phase during calcination. The deposited Co and Ni were efficient activity promoters in benzothiophene hydrodesulfurization.     

Ni/Al2O3 catalysts for CO methanation: Effect of Al2O3 supports calcined at different temperatures

The correlation between phase structures and surface acidity of Al₂O₃ supports calcined at different temperatures and the catalytic performance of Ni/Al₂O₃ catalysts in the production of synthetic natural gas (SNG) via CO methanation was systematically investigated. A series of 10 wt% NiO/Al₂O₃ catalysts were prepared by the conventional impregnation method, and the phase structures and surface acidity of Al₂O₃ supports were adjusted by calcining the commercial γ-Al₂O₃ at different temperatures (600–1200 °C). CO methanation reaction was carried out in the temperature range of 300–600 °C at different weight hourly space velocities (WHSV = 30000 and 120000 mL·g^?1·h^?1) and pressures (0.1 and 3.0 MPa). It was found that high calcination temperature not only led to the growth in Ni particle size, but also weakened the interaction between Ni nanoparticles and Al₂O₃ supports due to the rapid decrease of the specific surface area and acidity of Al₂O₃ supports. Interestingly, Ni catalysts supported on Al₂O₃ calcined at 1200 °C (Ni/Al₂O₃-1200) exhibited the best catalytic activity for CO methanation under different reaction conditions. Lifetime reaction tests also indicated that Ni/Al₂O₃-1200 was the most active and stable catalyst compared with the other three catalysts, whose supports were calcined at lower temperatures (600, 800 and 1000 °C). These findings would therefore be helpful to develop Ni/Al₂O₃ methanation catalyst for SNG production.     

Characterization of La-promoted Ni/Al2O3 catalysts for hydrogen production from glycerol dry reforming

In the current paper, dry (CO₂)-reforming of glycerol, a new reforming route, was carried out over alumina (Al₂O₃)-supported, non-promoted and lanthanum-promoted nickel (Ni) catalysts. Both sets of catalysts were synthesized via a wet co-impregnation procedure. Physicochemical characterization of the catalysts showed that the promoted catalyst possessed smaller metal crystallite size, hence higher metal dispersion compared to the virgin Ni/Al₂O₃ catalyst. This was also corroborated by the surface images captured by the FESEM analysis. From temperature-programmed calcination analysis, the derivative weight profiles revealed two peaks, which represent a water elimination peak at a temperature range of 373 to 473 K followed by nickel nitrate decomposition from 473 to 573 K. In addition, BET surface area measurements gave 85.0 m²·g⁻¹ for the non-promoted Ni catalyst, whilst the promoted catalysts showed an average of 1% to 6% improvement depending on the La loadings. Significantly, reaction studies at 873 K showed that glycerol dry reforming successfully produced H₂. The 2%La-Ni/Al₂O₃ catalyst, which possessed the largest BET surface area, gave an optimum H₂ generation (9.70%) at a glycerol conversion of 24.5%.     

Effect of synthesis solution pH of Co/γ-Al_2O_3 catalyst on its catalytic properties for methane conversion to syngas

The cobalt nanoparticles over γ-Al_2O_3 support were prepared via chemical reduction of CoCl_2·6H_2O using NaBH_4 with various values of pH in the range of 11. 92-13. 80. Synthesized catalysts were studied through X-ray diffraction( XRD),N_2 adsorption/desorption( BET),H_2-temperature programmed reduction( H_2-TPR),H_2-chemisorption,O_2 pulse titration and temperature programmed oxidation( TPO) methods. Obtained results exhibited the synthesis solution pH showed a significant influence on the activity and selectivity in partial oxidation of methane reaction. The methane conversion,CO selectivity and H_2 yield were enhanced by increasing of the synthesis solution pH. Compared to other catalysts,the catalyst that synthesized at pH of 13.80,showed a superior ability in syngas production with a H_2/CO ratio of near 2 and also a proper stability against deactivation during the partial oxidation of methane.     

Co或Ni促进的Cu/SiO2-Al2O3催化剂上丙三醇和苯胺气相合成3-甲基吲哚

对丙三醇和苯胺在Co或Ni促进的Cu/SiO2-Al2O3催化剂上气相合成3-甲基吲哚进行了研究.采用N2吸附、氢气程序升温还原(H2-TPR)、电感耦合等离子体(ICP)发射光谱、X射线衍射(XRD)、透射电子显微镜(TEM)、氨程序升温脱附(NH3-TPD)及热重(TG)分析等技术对催化剂进行了表征.结果表明,向Cu/SiO2-Al2O3催化剂加入钴或镍助剂改善了催化剂的催化性能,钴比镍更加有效.在催化剂Cu-Co/SiO2-Al2O3和Cu-Ni/SiO2-Al2O3上,反应第3 h,3-甲基吲哚收率分别达到47%和45%,而且催化剂经过6次再生收率仍能达到44%和42%.各种表征表明,向Cu/SiO2-Al2O3催化剂加入钴或镍助剂能增强铜和载体之间的相互作用,其结果不仅促进了铜粒子在载体表面的分散度,而且有效减少了反应过程中铜组分的流失.另外,加入钴或镍助剂还能减少催化剂的中强酸中心数,从而提高3-甲基吲哚的选择性,并且抑制积炭的形成.此外,钴助剂还能增加催化剂的弱酸中心数,促进3-甲基吲哚的生成.提出了金属铜与弱酸中心共同促进3-甲基吲哚合成的催化反应机理.     

Study of Fe-doped V<Subscript>2</Subscript>O<Subscript>5</Subscript>/TiO<Subscript>2</Subscript> catalyst for an enhanced NH<Subscript>3</Subscript>-SCR in diesel exhaust aftertreatment

Selective catalytic reduction (SCR) with ammonia has been considered as the most promising technology, as its effect deals with the NO_X. Novel Fe-doped V₂O₅/TiO₂ catalysts were prepared by sol–gel and impregnation methods. The effects of iron content and reaction temperature on the catalyst SCR reaction activity were explored by a test device, the results of which revealed that catalysts could exhibit the best catalytic activity when the iron mass ratio was 0.05%. It further proved that the VTiFe (0.05%) catalyst performed the best in denitration and its NO_X conversion reached 99.5% at 270 °C. The outcome of experimental procedures: Brunauer–Emmett–Teller surface area, X-ray powder diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, temperature-programmed reduction and adsorption (H₂-TPR, NH₃-TPD) techniques showed that the iron existed in the form of Fe³⁺ and Fe²⁺ and the superior catalytic performance was attributed to the highly dispersed active species, lots of surface acid sites and absorbed oxygen. The modified Fe-doped catalysts do not only have terrific SCR activities, but also a rather broad range of active temperature which also enhances the resistance to SO₂ and H₂O.