Photodegradation of poly(vinyl acetate)

Poly(vinyl acetate) (PVAc) films with different molecular masses were exposed to ultraviolet radiation. The infra-red spectra of all the samples showed a continuous attenuation of the intensity of the carbonyl stretching bands (1740 cm⁻¹) and of the symmetrical methyl bending vibration bands (1375 cm⁻¹), which suggests a steady loss of acetate side groups during irradiation.The electronic spectra showed an increase in the uv absorption at about 272 nm, suggesting the occurrence of polyene sequences in the polymer chains.In the low molecular mass sample there was almost no insoluble gel fraction formed, even after 20 h irradiation; in the high molecular mass polymer there was already a 50% insoluble fraction after 5 h irradiation, indicating a high degree of crosslinking, although the average viscometric molecular mass of the soluble fraction was only about one sixth of the initial value.     

Long branching in poly(vinyl acetate) and poly(vinyl alcohol). I. Crosslinking and crosslinking cleavage of poly(vinyl acetate)

A crosslinked network was formed by the reaction of partially saponified poly(vinyl acetate) and toluylene diisocyanate in benzene. The yield of gel was markedly dependent on the degree of saponification and the concentrations of polymer and diisocyanate. Crosslinked poly(vinyl alcohol) was obtained by treating the poly(vinyl acetate) with a catalytic amount of sodium hydroxide in methanol without any change of the urethane crosslinks. The crosslink based on the urethane linkage was quantitatively cleaved by acids, especially by hydrobromic acid, releasing polymers of the same molecular weight as the original.     

Structural relaxation in poly(vinyl acetate)

Structural relaxation in poly(vinyl acetate) (PVAc) in and slightly above the glass-transition region has been studied by monitoring the time dependence of enthalpy using differential scanning calorimetry and the frequency dependence of electric polarization by dielectric loss measurements. The results have been analyzed to yield the kinetic parameters characterizing the structural relaxation and are compared with similar analyses of previously published shear compliance and volume relaxation experiments. Relaxation of enthalpy, electric polarization, volume, and shear stress in PVAc all appear to be characterized by somewhat different relaxation times. The difference between the volume and enthalpy relaxation times, coupled with the fact that PVAc exhibits a Prigogine–Defay ratio greater than unity, is evidence for a previously proposed connection between the thermodynamics and kinetics of structural relaxation in terms of an order parameter model.     

Long branching in poly(vinyl acetate) and poly(vinyl alcohol). II. Polymerization of vinyl acetate in the presence of crosslinked poly(vinyl alcohol)

It is a common view that poly(vinyl acetate) has many branches at the acetyl side group, but that the corresponding poly(vinyl alcohol) has little branching. In order to study the branching in poly(vinyl acetate) and poly(vinyl alcohol) which is formed by chain transfer to polymer, the polymerization of ¹⁴C-labeled vinyl acetate in the presence of crosslinked poly(vinyl acetate), which was able to be decrosslinked to give soluble polymers, was investigated at 60°C and 0°C. This system made it possible to separate as well as to distinguish the graft polymer from the newly polymerized homopolymer. Furthermore, the degree of grafting onto the acetoxymethyl group and onto the main chain were estimated. It became clear that, in the polymerization of vinyl acetate, chain transfer to the polymer main chain takes place about 2.4 times as frequently at 60°C as that to the acetoxy group and about 4.8 times as frequently at 0°C.     

Grafting reactions of vinyl acetate onto poly[(vinyl alcohol)-co-(vinyl acetate)]

The grafting preference of vinyl acetate onto the methine carbon of poly(vinyl alcohol) (PVOH) versus the acetate group of poly(vinyl acetate) (PVAc) was determined as part of an attempt to prepare novel branched PVOH from partially hydrolyzed PVAc. The results showed long chain grafting on the acetate groups of the PVAc units rather than the methine carbons of the PVOH or PVAc units. Decreasing the monomer or initiator concentration decreased the molecular weight of the graft copolymer formed. Of the initiators studied, ammonium persulfate gave the largest increase in copolymer molecular weight. Both hydrolysis and reacetylation combined with gel permeation chromatography (GPC) and ¹³C-NMR of the fully hydrolyzed material were used to estimate the number and location of grafts. © 1996 John Wiley & Sons, Inc.     

Long branching in poly(vinyl acetate) and poly(vinyl alcohol). IV. Polymerization of vinyl trimethylacetate in the presence of crosslinked poly(vinyl acetate)

In order to clarify the grafting behavior of vinyl trimethylacetate (VTMAc) onto poly-(vinyl acetate) (PVAc), the polymerization of a radioactive VTMAc in the presence of a crosslinked PVAc gel was studied in accordance with the experimental technique described in the previous papers. It was found that, at 60°C, the grafting onto the main chain of PVAc takes place about 2.8 times as readily as that onto the acetyl side group on PVAc.     

Seeded polymerization of vinyl acetate using monodisperse poly(vinyl acetate) latex particles

The seeded polymerizations of vinyl acetate, using monodisperse poly(vinyl acetate) latex particles prepared in the absence of emulsifiers with potassium persulfate, have been investigated at 70°C with potassium persulfate as an initiator. New small particles were formed in the system containing a small amount of seed particles, but were not observed in the system containing a large amount of seed particles. The size of the secondary particles increased, and their number decreased, with an increase in the seed particle number. The minimum diameter of PVAc particles, which are stabilized by the sulfate ion groups bound at the end of polymer chains during polymerization, was determined to be 0.12 μm diameter from the limiting total surface area of seed particles which prevented further secondary nucleation. The minimum diameter of the particles increased as the speed of the stirrer increased. The new small particle number calculated using this value agreed well with that formed in the seeded polymerization.     

Effect of diluents on poly(vinyl acetate) dynamics

The effect of diluents and temperature on segmental motion in poly(vinyl acetate) was investigated by both NMR and ESR spectroscopy. Three classes of diluents were studied: chloroform, a thermodynamically good solvent; water, a poor solvent which slightly swells the polymer and lowers its glass transition temperature; and decane, a nonsolvent so poor it does not appear to swell the polymer nor lower the calorimetric glass transition temperature. At all temperatures investigated each type of diluent increased the segmental motion of the polymer over that of the bulk sample. Under the conditions studied, ¹³C and ²H NMR and nitroxide spin-label ESR data gave similar views of segmental motion of the polymer, indicating that in this amorphous polymer the segmental motion of the polymer may be safely inferred from spin-label data.     

Study of the miscibility of poly(vinyl pyridines) with poly(vinyl acetate), poly(vinyl alcohol) and their copolymers

Miscibility of poly(4-vinyl pyridine) (P4VP) and poly(2-vinyl pyridine) (P2VP) with poly(viny acetate) (PVAc), poly(vinyl alcohol) PVA and poly(vinyl acetate-co-alcohol) (ACA copolymers) has been investigated over a wide composition range. Differentiaal scanning calorimetry (DSC) results indicate that P2VP is immiscible with PVAC, PVA, and their copolymers over the whole composition range. In turn, P4VP appears to be immiscible with PVAC and PVA, but miscible with some ACA copolymers in certain range of composition. The P4VP-ACA phase diagram for different copolymer compositions has been determined. The variation of the glass transition temperature with composition for miscible mixtures was found to follow the Gordon-Taylor equation, with the parameter κ dependent upon copolymer composition. FTIR analysis of blends reveal the existence of specific interactions via hydrogen bonding between hydroxyl groups and the nitrogen of the pyridinic ring, which appear to be decisive for miscibility. © 1994 John Wiley & Sons, Inc.     

Low-frequency excitations in amorphous poly(vinyl acetate)

Raman-active modes have been detected in amorphous poly(vinyl acetate) in the frequency region 20–160 cm^?1. The low-frequency spectrum appears as a broad band for all three molecular weights examined. Spectra were recorded at two temperatures, 293 and 77 K, and found to show similar characteristics at both temperatures. The presence in solid amorphous polymers of broad structureless bands in general and their significance are discussed.     

Compatibility of binary systems of poly(methyl methacrylate), poly(vinyl chloride) and poly(vinyl acetate)

The influence of the thermal treatment on the stability in time of the dispersion degree of films containing binary polymer mixtures, poly(vinyl chloride)/poly(methyl methacrylate), poly(vinyl chloride)/poly(vinyl acetate) and poly(vinyl acetate)/poly(methyl methacrylate), was studied by thermogravimetry and optical microscopy with phase contrast. The dispersion degree depends particularly on the composition of the polymer mixture and can be improved by thermal treatment at temperatures above the glass temperatures of both homopolymers. It seems that this thermal treatment yields exclusively metastable structures with a general tendency to phase separation in a short time after thermal treatment, the heterogeneity mixtures (as film) being more pronounced.     

Compatibility studies on solid polyblends of poly(methyl methacrylate) with poly(vinyl acetate) and polystyrene by ultrasonic technique

The behaviours of solid compatible, poly(methyl methacrylate)-poly(vinyl acetate), and incompatible, poly(methyl methacrylate)-polystyrene, blends have been studied by ultrasonic velocity measurements. It has been found that, in the compatible blends, the ultrasonic velocity varies linearly with composition; it deviates from linearity in the incompatible blends. These results are in conformity with the results of sonic velocity measurements for various compatible and incompatible blends reported by Hourston and Hughes. The variation of ultrasonic velocity has been explained in terms of morphology of the blends, with further evidence from scanning electron microscopy.     

Morphology of poly(ethylene oxide)/poly(vinyl acetate) blends

The morphology of poly(ethylene oxide)/poly(vinyl acetate) (PEO/PVAc) blends was examined using small angle X-ray scattering (SAXS) and optical microscopy. The morphological and structural parameters of the blends are dependent on both composition and crystallization conditions. Optical microscopy revealed that blend samples prepared by solution casting crystallized with volume-filling crystals up to a composition of 30/70 wt% PEO/PVAc; at higher PVAc content there was no evidence of crystallization in the temperature range studied. Pure PEO always crystallized with a spherulite-hedrite morphology. The formation of spherulites was relatively favoured at lower crystallization temperatures and by addition of PVAc to PEO. Small angle X-ray intensity profiles were analyzed using a recently developed methodology and it was found that, for a given crystallization temperature, the amorphous and interphase thicknesses increased with increasing PVAc content but that the average crystalline thickness was independent of composition. The morphological and structural properties of the PEO/PVAc blends were attributed to the presence of non-crystallizable material in both the interlamellar and interfibrillar regions.     

Carbon-13 NMR of poly(vinyl acetate) and ethylene–vinyl acetate copolymer

Carbon-13 nuclear magnetic resonance spectra of atactic poly(vinyl acetate) and ethylene–vinyl acetate copolymers are reported and analyzed. Carbon spectra at 22.6 and 62.9 MHz together with use of shift reagents have permitted a more complete assignment than previously reported; in some cases the published assignments are found to be in error.     

Viscometric study of poly(vinyl chloride)/poly(vinyl acetate) blends in various solvents

The intermolecular interactions between poly(vinyl chloride) (PVC) and poly(vinyl acetate) (PVAc) in tetrahydrofuran (THF), methyl ethyl ketone (MEK) and N,N^′-dimethylformamide (DMF) were thoroughly investigated by the viscosity measurement. It has been found that the solvent selected has a great influence upon the polymer-polymer interactions in solution. If using PVAc and THF, or PVAc and DMF to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+THF) or (PVAc+DMF) is less than in corresponding pure solvent of THF or DMF. On the contrary, if using PVAc and MEK to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+MEK) is larger than in pure solvent of MEK. The influence of solvent upon the polymer-polymer interactions also comes from the interaction parameter term Δb, developed from modified Krigbaum and Wall theory. If PVC/PVAc blends with the weight ratio of 1/1 was dissolved in THF or DMF, Δb<0. On the contrary, if PVC/PVAc blends with the same weight ratio was dissolved in MEK, Δb>0. These experimental results show that the compatibility of PVC/PVAc blends is greatly associated with the solvent from which polymer mixtures were cast. The agreement of these results with differential scanning calorimetry measurements of PVC/PVAc blends casting from different solvents is good.     

Mechanical properties of blends of PAMAM dendrimers with poly(vinyl chloride) and poly(vinyl acetate)

Hybrid blends of poly(amidoamine) PAMAM dendrimers with two linear high polymers, poly(vinyl chloride), PVC, and poly(vinyl acetate), PVAc, are reported. The interaction between the blend components was studied using dynamic mechanical analysis, xenon nuclear magnetic resonance (NMR) spectroscopy, and tensile property measurements. The data suggest a much higher degree of interaction between components of PVAc-containing blends compared to those containing PVC. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 2111–2117, 1998     

Compatibility studies of polystyrene and poly(vinyl acetate) blends using electrostatic force microscopy

The effect of thermal treatment on the phase separation process of the components of a polymer blend was investigated using electrostatic force microscopy (EFM). EFM technique is an advance on conventional atomic force microscopy, which enables us to measure locally the dielectric properties of the samples under investigation providing compositional information. In this work, we studied the phase separation process of the polymer blend thin films made of polystyrene and poly(vinyl acetate) (PS/PVAc) (75/25 weight fraction). The samples were subjected to different thermal treatments. It was found that at low annealing temperature, PVAc forms many small islands within PS matrix. As the annealing temperature increases, the number of PVAc islands decreases with an increase in the size of the islands. These islands take spherical‐like shape when annealed at a temperature well above the glass transition temperatures of both the component polymers. Despite these morphological/topographical changes, EFM images evidence that there is no interdiffusion which was further confirmed by quantitatively measuring the value of the dielectric permittivity across the interphase. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1332–1338, 2011     

Characterization of poly(vinyl alcohol) during the emulsion polymerization of vinyl acetate using poly(vinyl alcohol) as emulsifier

During the emulsion polymerization of vinyl acetate (VAc) using poly(vinyl alcohol) (PVA) as stabilizer and potassium persulfate as initiator, the VAc reacts with PVA forming PVA-graft-PVAc. When the grafted polymer reaches a critical size it becomes water-insoluble and precipitates from the aqueous phase contributing to the formation of polymer particles. Since particle formation and therefore the properties of the final latex will depend on the degree of grafting, it is important to quantify and to characterize the grafted PVA. In this work, the quantitative separation and characterization of the grafted water-insoluble PVA was carried out by a two-step selective solubilization of the PVAc latex, first with acetonitrile to separate PVAc homopolymer, followed by water to separate the water-soluble PVA from the remaining acetonitrile-insoluble material. After the separation, the water-soluble and water-insoluble PVA were characterized by Fourier Transform Infrared (FTIR) spectroscopy and ¹H and ¹³C nuclear magnetic resonance (NMR) analyses, from which the details of the PVA-graft-PVAc structure were obtained. © 1996 John Wiley & Sons, Inc.