Synthesis and characterization of poly(ethylene glycol) grafted poly(L-lactide)

Poly(ethylene glycol) grafted poly(L -lactide) was prepared by ring opening polymerization of L -lactide and epoxy-terminated poly(ethylene glycol) methyl ether (PEGME). Stannous octoate and Al(Et)₃·0.5 H₂O were tested as polymerization catalysts, and Al(Et)₃·0.5 H₂O was found to be more effective for the ring-opening of the epoxy group of the modified PEGME monomer. The synthesized polymers were characterized by NMR and the efficiency of the incorporation of epoxy-terminated PEGME in the copolymer was determined.     

Synthesis and characterization of poly(ethylene glycol) methyl ether endcapped poly(ethylene terephthalate)

Linear and branched poly(ethylene terephthalate) (PET) copolymers with polyethylene glycol) (PEG) methyl ether (700 or 2000 g/mol) end groups were synthesized using conventional melt polymerization. DSC analysis demonstrated that low levels of PEG end groups accelerated PET crystallization. The incorporated PEG end groups also decreased the crystallization temperature of PET dramatically, and copolymers with a high content of PEG (>17.6 wt%) were able to crystallize at room temperature. Rheological analysis demonstrated that the presence of PEG end groups effectively decreased the melt viscosities and facilitated melt processing. XPS and ATR-FTIR revealed that the PEG end groups tended to aggregate on the surface, and the surface of compression molded films containing 34.0 wt% PEG were PEG rich (85 wt% PEG). PEG end-capped PET (34.0 wt% PEG) and PET films were immersed into a fibrinogen solution (0.7 mg/mL BSA) for 72 h to investigate the propensity for protein adhesion. XPS demonstrated that the concentration of nitrogen (1.05%) on the surface of PEG endcapped PET film was statistically lower than PET (7.67%). SEM analysis was consistent with XPS results, and revealed the presence of adsorbed protein on the surface of PET films.     

Synthesis and characterization of a multiblock copolymer of poly(N-isovaleryl ethyleneimine) and poly(ethylene glycol)

Block copolymers of poly(N-isovaleryl ethyleneimine) (PiVEI) and poly(ethylene glycol) (PEG) were synthesized by coupling previously prepared blocks of PEG ditosylate with the dianion of the dihydroxy PiVEI. On the average four blocks coupled together to form the final block polymer. The PiVEI blocks crystallized with the same melting points as in the homopolymer. This restricted the mobility of the PEG blocks and they did not crystallize unless cooled well below room temperature. The mechanical properties of cast films were quite good with a tensile strength of 77 kg/cm² and an elongation of 120%. The swelling of unoriented and oriented films with water was studied. The unoriented polymer absorbed about its own volume of water, even though PEG comprised only 40% of the total polymer.     

Synthesis and characterization of polyphenylenes with polypeptide and poly(ethylene glycol) side chains

We report a novel approach for fabrication of multifunctional conjugated polymers, namely poly(p‐phenylene)s (PPPs) possessing polypeptide (poly‐l ‐lysine, PLL) and hydrophilic poly(ethylene glycol) (PEG) side chains. The approach is comprised of the combination of Suzuki coupling and in situ N‐carboxyanhydride (NCA) ring‐opening polymerization (ROP) processes. First, polypeptide macromonomer was prepared by ROP of the corresponding NCA precursor using (2,5‐dibromophenyl)methanamine as an initiator. Suzuki coupling reaction of the obtained polypeptide and PEG macromonomers both having dibromobenzene end functionality using 1,4‐benzenediboronic acid as the coupling partner in the presence of palladium catalyst gave the desired polymer. A different sequence of the same procedure was also employed to yield polymer with essentially identical structure. In the reverse sequence mode, low molar mass monomer (2,5‐dibromophenyl)methanamine, and PEG macromonomer were coupled with 1,4‐benzenediboronic acid in a similar way followed by ROP of the L‐Lysine NCA precursor through the primary amino groups of the resulting polyphenylene. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1785–1793     

Synthesis and characterization of lipid-polymer hybrid nanoparticles with pH-triggered poly(ethylene glycol) shedding

Novel lipid-polymer hybrid nanoparticles are designed with a poly(ethylene glycol) (PEG) coating that is shed in response to a low pH trigger. This allows the nanoparticles to be stable during systemic circulation and at neutral pH, but destabilize and fuse with lipid membranes in acidic environments. The hybrid nanoparticles consist of a poly(lactic-co-glycolic acid) core with a lipid and lipid-PEG monolayer shell. To make the hybrid nanoparticles pH sensitive, a lipid-(succinate)-mPEG conjugate is synthesized to provide a hydrolyzable PEG stealth layer that is shed off the particle surface at low pH. The pH-sensitivity of the nanoparticles is tunable using the molar concentration of the lipid-(succinate)-mPEG incorporated in the lipid shell of the particles. Possible uses of these pH-sensitive nanoparticles include aggregating in acidic tumor microenvironments, escaping acidified endosomes, or aggregating in deep lung tissue for improved inhalation administration.     

Synthesis and characterization of a novel methoxy poly(ethylene glycol)-Tat peptide-chitosan copolymers

In this paper, a novel chitosan-g-(-O-methyl poly (ethylene glycol))-g-(-N-Tat peptide) (CS-mPEG-Tat) copolymer was synthesized. The synthesized intermediates and final products were characterized and confirmed by Fourier transform infrared spectrum, ¹H nuclear magnetic resonance spectrum, and X-ray diffraction, respectively. The particle sizes, size distributions, and zeta potentials can also be determined by dynamic light scattering. Agarose gel electrophoresis study showed effective DNA-binding ability of CS-mPEG-Tat. In vitro cytotoxicity assay indicated that CS-mPEG-Tat copolymers were low toxic and cell compatible as the polymer concentration was smaller than 5 mg/ml. This work provides a facile approach to prepare biocompatible PEG-peptide-chitosan copolymer nanoparticles with controllable performances. In conclusion, the obtained CS-mPEG-Tat copolymer might be attractive cationic polymers for nonviral gene therapy.     

Synthesis and characterization of ultrathin WO3 nanodisks utilizing long-chain poly(ethylene glycol)

Metal oxide nanostructures hold great potential for photovoltaic (PV), photoelectrochemical (PEC), and photocatalytic applications. Whereas thin films of various materials of both nanoparticle and nanorod morphologies have been widely investigated, there have been few inquiries into nanodisk structures. Here, we report the synthesis of ultrathin WO3 nanodisks using a wet chemical route with poly(ethylene glycol) (PEG) as a surface modulator. The reported nanodisk structure is based on the interaction of the nonionic 10000 g/mol PEG molecules with tungsten oxoanion precursors. The WO3 nanostructures formed are dominated by very thin disks with dimensions on the nanometer to micrometer scale. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) images reveal the structures to have dimensions on the order of 350-1000 nm in length, 200-750 nm in width, and 7-18 nm in thickness and possessing textured single-crystalline features. A number of analytical techniques were used to characterize the WO3 nanodisks, including selected-area electron diffraction (SAED), X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDX), atomic force microscopy (AFM), Raman scattering spectroscopy, UV-visible spectrophotometry, and cyclic voltammetry (CV). The growth of the WO3 nanodisks was inhibited in the [010] crystal direction, leading to ultrathin morphologies in the monoclinic crystal phase. The large flat surface area and high aspect ratio of the WO3 nanodisks are potentially useful in PEC cells for hydrogen production via direct water splitting, as has been demonstrated in a preliminary experiment with external bias.     

Synthesis and characterization of poly(ethylene glycol) bottlebrush networks via ring-opening metathesis polymerization

Herein it is reported how the overlap concentration (C*) can be used to overcome crosslinking due to diol impurities in commercial poly(ethylene glycol) (PEG), allowing for the synthesize of bottlebrush polymers with good control over molecular weight. Additionally, PEG-based bottlebrush networks are synthesized via ring-opening metathesis polymerization, attaining high conversions with minimal sol fractions (<2%). The crystallinity and mechanical properties of these networks are then further altered by solvent swelling with phosphate buffer solution and 1-ethyl-3-methylimidazolium ethyl sulfate/dichloromethane cosolvents. The syntheses reported here highlight the potential of the bottlebrush network architecture for use in the rational design of new materials.     

Synthesis and characterization of novel biodegradable unsaturated poly(ester amide)/poly(ethylene glycol) diacrylate hydrogels

A series of novel biodegradable hydrogels were designed and synthesized from four types of unsaturated poly(ester amide) (UPEA) and poly(ethylene glycol) diacrylate (PEG‐DA) precursors by UV photocrosslinking. These newly synthesized biodegradable UPEA/PEG‐DA hydrogels were characterized by their gel fraction (G_f), equilibrium swelling ratio (Q_eq), compressive modulus, and interior morphology. The effect of the precursor feed ratio (UPEAs to PEG‐DA) on the properties of the hydrogels was also studied. The incorporation of UPEA polymers into the PEG‐DA hydrogels increased their hydrophobicity, crosslinking density (denser network), and mechanical strength (higher compressive modulus) but reduced Q_eq. When different types of UPEA precursors were coupled with PEG‐DA at the same feed ratio (20 wt %), the resulting hydrogels had similar Q_eq values and porous three‐dimensional interior morphologies but different G_f and compressive modulus values. These differences in the hydrogel properties were correlated to the chemical structures of the UPEA precursors; that is, the different locations of the >C?C< double bonds in individual UPEA segments resulted in their different reactivities toward PEG‐DA to form hydrogels. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3932–3944, 2005     

Synthesis and characterization of poly(ethylene glycol amine) electrolytes and nanocomposites based on graphite

Poly(ethylene glycol) functionalized with an amino group (PEG-amine) was synthesized and characterized by proton NMR and FTIR spectroscopy. The polymer was complexed with lithium triflate (LiOTf) in varying ratios, and it was found that the composition (PEG-amine)_8.0LiOTf exhibited a maximum ionic conductivity of 10^?5 S/cm at a temperature of 320 K. Graphite platelets were also dispersed into the polymer matrix, and the resulting nanomaterials were shown to be electrically conductive, with a maximum value of 1 × 10³ S/cm when the graphite is present at 50% by mass.     

Synthesis and characterization of poly(ethylene glycol) polymers functionalized by terminal tributyltin carboxylate moieties

Novel polymeric derivatives of various average molecular weights bearing tributyltin carboxylate moieties as terminal groups have been prepared by esterification with bis(tributyltin) oxide of the corresponding poly(ethylene glycol)s functionalized with dimethylenecarboxylic end groups. Low‐molecular‐weight compounds have also been synthesized, with the aim of investigating the influence of the polymeric chain on tin properties. As investigated by Sn NMR and Fourier transform infrared, the metal center appears to be completely tetracoordinated in chloroform solution at room temperature, whereas at low temperature, the tin atom undergoes a fast exchange between intramolecular pentacoordination with the ethereal oxygen atoms and the unassociated form. In the solid state, even at room temperature, all the polymeric products exhibit both tetracoordination and pentacoordination at tin, the latter achieved by interaction with both ethereal and carbonyl oxygens. The thermal behavior of the series of compounds indicates the presence of crystalline domains in the material, which can be ascribed either to intermolecular interactions at tin, giving rise to organometal aggregates, or to the formation of an ordered phase induced by the presence of the macromolecular chain, depending on the more or less elevated relative concentration of the organotin moieties in the sample. These findings are also confirmed by the X‐ray diffractions patterns of the investigated products. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3091–3104, 2005     

Preparation and characterization of p-toluene sulfonyl ester and amino derivatives of tri- and poly(ethylene glycol)

Methods described in the literature are inadequate for the preparation of pure polyethylene glycol (PEG) tosylate. Therefore an improved method is presented. The hydroxyl groups on PEG can be quantitatively converted into the tosylate and isolated from the reaction medium free from impurities with no chain cleavage or reduction in molecular weight. 1,2-Di(N-phenyl 2-aminoethoxy) ethane, α,ω-di(N-phenyl 2-aminoethyl) poly(oxyethylene), and α,ω-di(N-phenyl, N-benzyl 2-aminoethyl) poly(oxyethylene) were prepared from the tosylates of tri- and poly(ethylene glycol)s and the corresponding primary and secondary aromatic amines.     

Preparation and preliminary characterization of poly(ethylene glycol)-pepstatin conjugate

The carboxyl function of pepstatin has been coupled, through an amide bond, to methoxypoly(ethylene glycol) (5 kDa), to which an amino function had been previously grafted. The mPEG-pepstatin conjugate inhibits hog pepsin (aspartic proteinase) in vitro as pepstatin itself, however, with a 400 times higher apparent K_i. The conjugate apparently does not inhibit proteinases belonging to other proteinase families such as serine (trypsin, carboxypeptidase Y), cysteine (Papaya proteinase III), or metallo (collagenase) proteinases.     

Synthesis of novel poly(ethylene glycol) based amphiphilic polymers

The synthesis of new amphiphilic polyesters based on poly(ethylene glycol) (PEGs) and studies on their solution properties are reported. Two novel monomers, dimethyl 5-n-butoxy isophthalate (2) and dimethyl 5-n-octoxy isophthalate (3) were synthesized. Three series of novel amphiphilic polyesters, i.e. poly(ethyleneoxy isophthalate)s (10-15), poly(ethyleneoxy n-butoxy isophthalate)s (16-21) and poly(ethyleneoxy n-octoxy isophthalate)s (22-27) have been synthesized from PEGs of different sizes and dimethyl isophthalates 1-3 via the transesterification-polycondensation using dibutyltin diacetate as a catalyst. The structures of the polyesters were established from a detailed analysis of their spectra, i.e. FTIR, ¹H-NMR (one- and two-dimensional) and ¹³C-NMR. By adjusting the ratio of hydrophobic (diesters) and hydrophilic (PEGs) segments in polymers, their main chain structures and solution properties could be changed. The viscosity molecular weights (M_v) of polymers, obtained from Mark-Houwink-Sakurada relationship having poly(ethylene terephthalate) as a model, were in the range of 4500-32,000 g/mol. Intrinsic viscosities were studied based on polymer backbone length (PEGs effect) and pendant group (diesters effect) and these were found to be dependent on molecular weights of the PEGs used.     

Synthesis and characterization of ABA-type block copolymer of poly(trimethylene carbonate) with poly(ethylene glycol): Bioerodible copolymer

ABA-type block copolymers of poly(trimethylene carbonate) with poly(ethylene glycol) (M_n 6820), PTMC-b-PEG-b-PTMC, were synthesized by the ring-opening polymerization of 1,3-dioxan-2-one (trimethylene carbonate) in the presence of poly-(ethylene glycol) with stannous octoate catalyst, and the copolymers with various compositions were obtained. The PTMC-b-PEG-b-PTMC copolymers were characterized with Fourier transform infrared and nuclear magnetic resonance spectroscopies. The intrinsic viscosities of resulting copolymers increased with the increase of 1,3-dioxan-2-one content in feed while the molar ratio of monomer over catalyst kept constant. It has been observed that the glass transition temperature (T_g) of the PTMC segments in copolymers, recorded from differential scanning calorimetry, was dependent on the composition of copolymers. The melting temperature (T_m) of PEG blocks in copolymer was lower than that of PEG polymer, and then disappeared as the length of PTMC blocks increased. The results of dynamic contact angle measurement clearly revealed that the hydrophilicity of resulting copolymers increased greatly with the increase of PEG content in copolymers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 695–702, 1998     

Segmented block copolymers of poly(ethylene glycol) and poly(ethylene terephthalate)

A new series of segmented copolymers were synthesized from poly(ethylene terephthalate) (PET) oligomers and poly(ethylene glycol) (PEG) by a two‐step solution polymerization reaction. PET oligomers were obtained by glycolysis depolymerization. Structural features were defined by infrared and nuclear magnetic resonance (NMR) spectroscopy. The copolymer composition was calculated via ¹H NMR spectroscopy. The content of soft PEG segments was higher than that of hard PET segments. A single glass‐transition temperature was detected for all the synthesized segmented copolymers. This observation was found to be independent of the initial PET‐to‐PEG molar ratio. The molar masses of the copolymers were determined by gel permeation chromatography (GPC). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4448–4457, 2004     

Synthesis of poly(ethylene glycol) block copolymers by a redox process and their spectral characterization

Novel block copolymers of poly(ethylene glycol) (PEG) with acrylamide (AAm) and methacrylic acid (MAA) were synthesized using a redox system consisting of ceric ions and PEG in aqueous acidic medium. The molecular weight of PEG in the redox system was varied to obtain a series of block copolymers with differing molecular weights of PEG segment. The polymerization proceeded via macroradical generation, which was substantiated by ESR spectroscopy. This macroradical acted as a redox macroinitiator for the block copolymerization of the vinyl monomers. The formation of the block copolymers was confirmed by fractional precipitation technique.     

Synthesis and characterization of self-coloured poly(ethylene terephthalate)

By polycondensation of ethylene glycol, dimethyl terephthalate and N,N-bis(4-ethoxicarbonyl)-pyromellitic diimide, a self-coloured polyester was obtained. Characterization of this self-coloured polyester and dope dyed poly(ethylene terephthalate) by gel permeation chromatography and other analytical methods reveal the influence of dyes upon physical-chemical properties of these polyesters.     

Synthesis and characterization of poly(vinylcyclohexane) derivatives

Six nearly monodisperse substituted poly(styrene) homopolymers, poly(styrene) (PS), poly(2-methylstyrene) (P2MS), poly(3-methylstyrene) (P3MS), poly(4-methylstyrene) (P4MS), poly(tertiary-butylstyrene) (PtBS), and poly(α-methylstyrene) (FαMS) were anionically polymerized and subsequently saturated using heterogeneous hydrogenation techniques to poly(vinylcyclohexane) (PVCH), poly(2-methylvinylcyclohexane) (P2MVCH), poly(3-methylvinylcyclohexane) (P3MVCH), poly(4-methylvinylcyclohexane) (P4MVCH), and poly(tertiary-butylvinylcyclohexane) (PtBVCH), respectively. In each case, except PαMS, the materials were saturated to > 99% conversion with no chain degradation. PS hydrogenations required the addition of small amounts of tetrahydrofuran to the reaction solvent cyclohexane to enhance miscibility and eliminate large-scale chain degradation. Density gradient and differential scanning calorimetry (DSC) measurements were used to characterize the density and glass transition temperature, T_g, of the unsaturated and saturated polymers. Saturation reduces the density by 3% to 11% and changes T_g substantially. The greatest variation in T_g is obtained with the 3-methyl substituted species where a 63°C increase is observed, while the highest measured T_g is 186°C for P2MVCH. Small-angle neutron scattering (SANS) experiments on binary mixtures of hydrogenous and deuterium labeled PVCH derivatives provided a determination of bulk chain statistics. The statistical segment length is relatively insensitive to vinylcyclohexane ring substitution, except with P3MVCH where a 20% greater value is obtained. ©1995 John Wiley & Sons, Inc.