Solution behavior of random copolymers of styrene with sodium-2-acrylamido-2-methylpropane sulfonate

The nonaqueous solution behavior of random copolymers of styrene (ST) with sodium-2-acrylamido-2-methylpropane sulfonate (Na-AMPS) [poly(ST-Na-AMPS)] has been investigated using the transient electric birefringence (TEB) technique. The copolymers with varying high sulfonate contents (about 30–70 mol%), bridging the gap between conventional ionomers and classical polyelectrolytes, were dissolved in the solvent methylformamide (MFA) with a high permittivity ? of ca. 190. The solutions showed a negative birefringence at electric field strength E of the order of kV/cm. A typical Kerr effect was observed at low polymer concentrations C of ca. 10^?3g/mL and electric field strengths of the order of kV/cm. However, the detailed, TEB studies demonstrated different behavior at two concentration regimes in dilute solution. At a low concentration regime (e.g., C ≤ 1 × 10^?3g/mL for the copolymer with a 66.7 mol % sulfonate content) where the reduced viscosity exhibited a pronounced polyelectrolyte effect, the birefringence signal pattern showed a maximum before reaching a steady value. Additionally, during the rise at an applied electric field strength beyond a threshold value, it was observed that the nonexponential field-free decay was slower than the single exponential field-induced rise. The observed anomalous behavior was similar to those of a polyelectrolyte [sodium poly (styrene sulfonate)] in aqueous solution and might be attributed to the perturbation of the molecular shape by the applied electric field. At the higher concentration regime (e.g., C ≥ 4 × 10^?3g/mL for the same copolymer with a 66.7 mol % sulfonate content) where the polyelectrolyte effects started to diminish as indicated by the viscosity study, the birefringence shape showed no variation with an increased electric field strength and the field-free decay turned out to be faster than the single exponential rise. The dissociation of ionic aggregates was tentatively interpreted to be responsible for this observation. It seems that by simply varying the polymer concentration, poly (ST-Na-AMPS) could behave either as a polyelectrolyte or as an ionomer in a single polar organic solvent.     

Water-soluble copolymers. XIII. Copolymers of acrylamide with sodium-3-acrylamido-3-methylbutanoate: Solution properties

Dilute solution properties of copolymers of acrylamide (AM) with sodium-3-acrylamido-3-methylbutanoate (NaAMB) of known molecular weight have been studied as a function of composition, temperature, time, pH, and added electrolytes. Phase separation and potentiometric studies have also been performed. The AM–NaAMB copolymers exhibit high solution viscosities, good salt tolerance, and moderate viscosity-temperature coefficients. In addition, these copolymers exhibit no phase separation in the presence of divalent cations as is common with many such carboxylated polyelectrolytes. These properties are due to favorable conformations in solution resulting from microstructure and hydrogen bonding effects.     

Water-soluble copolymers. XII. Copolymers of acrylamide with sodium-3-acrylamido-3-methylbutanoate: Synthesis and characterization

The copolymerization of acrylamide (AM) with sodium-3-acrylamido-3-methylbutanoate (NaAMB) has been studied. The value of r₁r₂ has been determined to be 0.56 for the AM–NaAMB pair. The molecular weights of the copolymers were relatively unaffected by monomer feed ratios. The copolymer microstructures, including run numbers and sequence distributions, were calculated from the reactivity ratios. The solution properties of the AM–NaAMB copolymers, as well as the NaAMB homopolymer, will be reported in a subsequent paper.     

Radical copolymerization of sodium 2-acrylamido-2-methylpropane sulfonate and sodium acrylate in water-alcohol solutions

The effect of the nature of a solvent on the kinetic parameters of the process and the intrinsic viscosities of copolymers formed by the homogeneous free-radical copolymerization of the sodium salt of 2-acrylamido-2-methylpropane sulfonic acid and the sodium salt of acrylic acid initiated by potassium persulfate in water, water-methanol mixtures (92: 8, 84: 16, 75: 25, 50: 50), and water-isopropanol (50: 50) mixtures at pH 9 and 60°C is studied. The initial rate of copolymerization increases with increases in the concentrations of the comonomers and initiator, the content of 2-acrylamido-2-methylpropane sulfonic acid in the initial monomer mixture, and the content of water in a water-methanol mixture and in the sequence of solvents water-methanol < water-isopropanol. The intrinsic viscosity and yield of the copolymer grow when the content of 2-acrylamido-2-methylpropane sulfonic acid in the initial monomer mixture and water in water-methanol mixtures are increased and when isopropanol is replaced with methanol. The reactivity ratios of the monomers in water-methanol (50: 50) and water-isopropanol (50: 50) mixtures are determined.     

Water-soluble copolymers. XLII. Cationic polyelectrolytes of acrylamide and 2-acrylamido-2-methylpropanetrimethylammonium chloride

The new monomer 2-acrylamido-2-methylpropanetrimethylammonium chloride (AMP-TAC, M₂) has been synthesized. Free radical copolymerization with acrylamide (AM, M₁) in feed ratios varying from 10 to 50 mol % AMPTAC gave the cationic ATAM series. Copolymer compositions were determined from ¹³C-NMR. The reactivity ratio product r₁r₂ was found to be 0.62. Molecular weights varied from 1.4 to 16.5 × 10⁶ g/mol for the copolymers. Turbidimetric studies showed aqueous solutions of the copolymers to be phase stable in the presence of CaCl₂ and Na₂CO₃ up to 100°C. Solution behavior was independent of pH in the range of 3 to 11, and temperature in the range of 25 to 60°C. Intrinsic viscosities of the cationic copolymers decreased with the addition of electrolytes; however, some samples showed curvature in plots of intrinsic viscosity versus the inverse square root of ionic strength. © 1993 John Wiley & Sons, Inc.     

Effect of fire retardant on flammability of acrylamide and 2-acrylamido-2-methylpropane sodium sulfonate copolymer composites

Poly[acrylamide-co-(2-acrylamido-2-methylpropane sodium sulfonate)] superabsorbents and superabsorbent composites (SAPCs) with zinc borate and/or melamine as fire retardants were synthesized. Water absorbencies decreased inversely to added amount of fire retardant. Thermal stability of SAPC/zinc borate increases with increasing zinc borate. Incorporating melamine improved thermal stability of the SAPC until 300 °C. Flammability analysis demonstrated that wood surface coated with SAP or SAPC emulsions extended time to ignition of the wood. Peak heat release rate and total heat release are smallest in specimens coated with SAPC/30% melamine. Wood coated with SAPC incorporating 20% zinc borate/10% melamine mixture gave the longest time to ignition at 4½ min.     

Gamma radiation induced graft copolymerization of acrylamide onto EPDM blended with PE

Gamma radiation induced grafting of acrylamide (AAm) onto vulcanized strips of EPDM and EPDM/PE blends has been carried out. The effects of different parameters on the graft yield have been investigated. These parameters include: radiation dose, monomer concentration, diluent composition and types of inhibitors. It has been found that water is the most appropriate solvent. The preswelling of crosslinked rubber samples in cyclohexane prior to grafting enhances the grafting and the addition of methanol to water as binary diluent in the ratio (1 : 1) decreases the graft yield. The presence of Mohr's salt and copper sulfate in the reaction mixture in the molar ratio (2.1 : 0.5) markedly increases the graft yield. Evidence of grafting have been conducted using thermal analysis as well as swelling measurements in water. Also, it has been found that the mechanical properties of the blends decrease at graft yield 13%. Copyright © 2002 John Wiley & Sons, Ltd.     

Development of highly ionic conductive cellulose acetate-g-poly (2-acrylamido-2-methylpropane sulfonic acid-co-methyl methacrylate) graft copolymer membranes

A novel cellulose acetate-g-poly (2-acrylamido-2-methylpropane sulfonic acid-co- methyl methacrylate) copolymer was prepared via free radical polymerization for the first time. The chemical structure of the graft copolymer was confirmed using FT-IR, ¹H NMR and EDX. The TGA and DSC investigated the thermal changes. Factors affecting the grafting process were studied and various grafting characteristic parameters such as grafting efficiency (%), grafting yield (%) and add-on value (%) were determined. Flexible membranes based on different graft copolymer compositions were fabricated by simple solution casting. Physicochemical properties including ion exchange capability (IEC), water uptake (WU) and proton conductivity (σ) were evaluated. These membranes demonstrated higher IEC, WU and conductivity than the pristine CA. The maximum proton conductivity of the CA-g-poly (2-acrylamido-2-methylpropane sulfonic acid-co- methyl methacrylate) copolymer membrane (68%; Add-on %) was found to be 6.44 × 10⁻³ S/cm compared with 0.035 × 10⁻³ S/cm of the pristine CA. Thus, the appropriate graft copolymer composition will allow fine-tuning of the physical characteristics and led to several potential applications, such as polyelectrolyte fuel cells membranes or biodiesel production.     

A resistive-type humidity sensor using composite films prepared from poly(2-acrylamido-2-methylpropane sulfonate) and dispersed organic silicon sol

A composite material of dispersed organic silicon sol and poly(2-acrylamido-2-methylpropane sulfonate) (poly-AMPS) was used to make humidity sensor without protective film or complicated chemical procedures. The organic silicon sol was dispersed well in the poly-AMPS without using dispersion agent. Parameters that may affect the water-resistive but humidity-sensitive characteristic of composite material, the adding amount of organic silicon sol solution and the film of thermal treatment time, were investigated. The microstructure of the material was analyzed, and the humidity sensing and electrical properties of the sensor were measured. The sensor well responded to humidity with a relatively good linearity, though it depended on the applied frequency. The temperature influence between 15 and 35 °C was within −0.17 % relative humidity (RH)/°C in the range of 30–90% RH. The activation energy was maximum around 40% RH. The sensor showed the hysteresis within 5.9%, fast response time, long-term stability (75 days at least) and satisfactory resistance to high humidity atmosphere (97% RH) and chemical environment (20% C₂H₅OH vapor). Analyzing the structure and complex impedance plots of organic silicon sol/poly-AMPS was used to explain improvement in humidity sensing properties in comparison with nano-sized SiO₂ powder/poly-AMPS films.     

Hydrogels of sodium alginate based copolymers grafted with sodium-2-acrylamido-2-methyl-1-propane sulfonate and methacrylic acid for controlled drug delivery applications

Novel sodium alginate based hydrogels were prepared by grafting the binary mixture of methacrylic acid and sodium-2-acrylamido-2-methyl-1-propane sulfonate on to sodium alginate (SA) with N,N'-methylenebisacrylamide (MBA) and ammonium persulfate (APS) as crosslinker and initiator respectively. The resultant SA-g-poly(AMPSNa-co-MAA) hydrogels were characterized using Fourier Transform Infrared Spectroscopy (FT-IR), Scanning Electron Microscopy (SEM), Thermo Gravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC) and X-Ray Diffraction (XRD). The results indicated that an increase in the amount of sodium-2-acrylamido-2-methyl-1-propane sulfonate, swelling capacity was found to increase. The effects of temperature, pH and inorganic salt on the swelling behavior of the hydrogels were investigated. The pH reversibility behavior at pH levels of 1.0 and 9.0 indicated great potential of this hydrogel as a candidate system for controlled drug delivery.     

Gamma radiation induced graft copolymerization of vinyl monomers onto poly(vinyl alcohol)

In an attempt to modify water-soluble synthetic polymers, graft Copolymerization of methylmethacrylate (MMA) and ethyl acrylate (EA) onto poly(vinyl alcohol), PVA, has been studied by using gamma irradiation from a Co⁶⁰ source as initiator. The graft copolymerization was carried out in an aqueous medium by the mutual method in air. The effect of total dose and concentration of vinyl monomers on percentage of grafting has been determined. Water plays a significant role in the enhancement of graft copolymerization and the optimum amount of water to afford maximum grafting has been evaluated. The effect of CH₃OH on aqueous grafting of MMA and EA by radiation method has been studied. The graft copolymer has been characterized by IR spectroscopic and thermogravimetric methods.     

Novel low humidity sensor made of TiO(2) nanowires/poly(2-acrylamido-2-methylpropane sulfonate) composite material film combined with quartz crystal microbalance

A novel ceramic nanowires of TiO₂ and poly(2-acrylamido-2-methylpropane sulfonate) (TiO₂ NWs/PAMPS) composite material films coated on quartz crystal microbalance (QCM) was prepared as a low humidity sensor. The 50 wt.% of TiO₂ NWs/PAMPS composite material films showed excellent sensitivity (2.63 −ΔHz/Δppm_v) at 31.5 ppm_v), linearity (R² = 0.9959) and acceptable response time (64 s at 34.6 ppm_v). The low humidity sensing mechanism was discussed in terms of surface texture and nanostructured morphology of the composite materials. Moreover, the adsorption dynamic analysis, molecular mechanics calculation (association constant), was used to elucidate the effect of adding 50 wt.% TiO₂ NWs into PAMPS in the increased sensitivity of low humidity sensing.     

Spontaneous copolymerization of 2-acrylamido-2-methylpropanesulfonic acid with acrylamide and acrylonitrile in concentrated aqueous solutions

Spontaneous copolymerization of 2-acrylamido-2-methylpropanesulfonic acid with acrylamide and acrylonitrile in concentrated acidic aqueous solutions was studied.     

Radiation-induced graft copolymerization of mixtures of styrene and acrylamide onto cellulose acetate. I. Effect of solvents

The grafting of styrene and acrylamide, from both their binary and unitary systems, on cellulose acetate film was studied by means of the cobalt-60 postirradiation grafting technique. The extent of grafting was found to be dependent on preirradiation dose, reaction time, and temperature, and the optimum conditions were evaluated. The effect of solvents, e.g., water, methanol, ethanol, isopropanol, and t-butanol were studied. The composition of the binary mixture as well as the nature of the alcohol used as the solvent were found to have a strong influence in modifying the course of grafting. Each component of the binary monomer mixture was found to sensitize the grafting of the other, when the former is present in relatively large concentration. The observed results are discussed in detail in terms of relative molecular reactivity and reactivity ratios.     

Radiation-induced graft copolymerization of mixtures of styrene and acrylamide onto cellulose acetate. III. A kinetic study

The kinetics of graft copolyermization of styrene and acrylamide from their binary monomer mixtures onto gamma-irradiated cellulose acetate film was studied. The extent of grafting increased with a rise in reaction time and temperature. The nature of the radical site on the trunk polymer was acertained in a study of grafting at different temperatures when the trunk polymer was irradiated in the presence and absence of oxygen. The character of the radical was tested further in a study of the ESR spectrum. The variation in grafting rates and energies of activation required for graft copolyermization at various mole ratios of the monomers was observed. The grafting rates showed a maximum at 1:1 mol ratio of monomers which was also associated with minimum energy of activation. The Kk_t values in the system were dependent on the composition of monomers.     

Cerium (IV)-2-chloroethanol redox-pair initiated polymerization of acrylamide in aqueous medium

The kinetics of acrylamide polymerization has been investigated by employing cericammoniumnitrate-2-chloroethanol redox pair under nitrogen atmosphere at 30 ± 1°C. The rate of monomer disappearance is directly proportional to the concentration of 2-chloroethanol (1.0 × 10^?2 ? 10.0 × 10^?2 mol. dm^?3) and is inversely proportional to the ceric ion concentration (2.5 × 10^?3 ? 10.0 × 10^?3 mol. dm^?3) but shows square dependence to the concentration of monomer (5.0 × 10^?2 ? 25.0 × 10^?2 mol. dm^?3). The rate of ceric ion disappearance is directly proportional to the initial concentration of ceric ion and 2-chloroethanol but independent of acrylamide concentration. The viscometric average molecular weight (M _v) decreases on increasing the concentration of ceric ion and increases on increasing the concentrations of acrylamide and 2-chloroethanol. A tentative mechanism has been proposed.     

Studies on graft copolymerization onto cellulose derivatives. XXIX. Photo-induced graft copolymerization of methyl methacrylate onto chitin and oxychitin

Graft copolymerization of methyl methacrylate (MMA) onto chitin and oxidized chitin was carried out by a noncatalytic photo-induced and a photo-sensitized method. The isolation method of grafted chains without a decrease in their degree of polymerization (DP) by sulfuric acid hydrolysis and the effects of some factors on the conversion and the grafted chain length have been studied. In case of the photo-induced graft copolymerization, if a small amount of dimethylformaldehyde (DMF) is added in the polymerization system, the induction period is shortened and the degree of grafting and the apparent number of grafted chains increase. The degree of grafting and the apparent number of grafted chains of the oxidized chitin containing a small amount of C?O groups are greater than those of the untreated chitin, but a further increase in C?O groups decreases these values. In the presence of this two species of the chitin samples, the polymerization reaction was carried out as functions of monomer and chitin concentrations. From these results, the mechanisms of the photo-induced graft copolymerization were discussed. It is also clear that the conversion and the apparent number of grafted chains by the noncatalytic photo-induced method are generally larger than those by the photo-sensitized method, and the grafting activity with hydrogen peroxide (HPO) is higher than that with azobisisobutyronitrile (AIBN).     

Radiation-induced graft copolymerization of mixtures of styrene and acrylamide onto cellulose acetate. II. Studies on bromine labeling

Formation of the active sites on irradiated trunk polymer, for example, cellulose acetate, was determined by taking recourse to bromine labeling and the G values of active sites were accordingly evaluated. The G value was as well determined through analysis of peroxide. It has been concluded that the G value measured by bromine labeling corresponds to accessible radicals, while that evaluated through measurement of peroxide accounts for the total. The number-average molecular weights of the graft chains were calculated and these were found to be dependent on monomer composition.