高密度聚乙烯／超高分子量聚乙烯共混物高取向薄膜形态结构与力学性能的研究

he morphology and properties of highly oriented films of blends ofHDPE/ UHMWPE were investigated by electron microscope, DSC and mechnicalproperty measurements. The as-drawn films of HDPE consist of highly oriented lamellar structure.The lamellar growing direchon is vertical to the drawing direction. AddingUHMWPE into HDPE results in formation of fibrous crystals with their fibrousaxis directions parallel to the drawing direction. The number of the fibers in thefilms of the blends increases with the increase of the content of UHMWPE. The presence of ultra - high molecular weight component in as - drawn blends films results in the increase of tensile modulus considerably.     

Cavitation and morphological changes in polypropylene deformed at elevated temperatures

Polypropylene (PP) thick films were subjected to tensile drawing at various temperatures from the room temperature to 100 °C. Morphological alterations during drawing were followed by wide‐angle X‐ray scattering, small‐angle X‐ray scattering, and scanning electron microscopy (SEM) of sectioned and etched samples, volume strain measurement, and light transparency measurement at various level of strain. The morphological observations were paralleled with stress–strain determination. Samples drawn at 25 and 40 °C undergo severe cavitation contributing to their volume increase up to 90–95%. The volume increase contributes greatly to the engineering strain. PP drawn at 70 and 100 °C does not cavitate. At the strain up to 1.2, a high lamellae orientation is observed in SEM, whereas the 2D WAXS patterns show in contrary circular diffraction rings indicating low orientation of crystals. The rotation of lamellae toward drawing direction is associated with reverse rotation of chains in crystals due to fine chain slips. These two rotations in opposite directions counterbalance resulting in a much weaker crystal orientation than expected from the SEM images. Noncavitating samples retain their translucency up to a high strain. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1271–1280, 2010     

高密度聚乙烯／超高分子量聚乙烯共混物高取向薄膜形态结构与力学性能的研究

高密度聚乙烯／超高分子量聚乙烯共混物高取向薄膜形态结构与力学性能的研究张伟广，赵勇，杨德才中国科学院长春应用化学研究所，高分子物理开放实验室，长春，１３００２２）关键词ＨＤＰＥ、ＵＨＭＷＰＥ、共混物、形态结构、力学性能如何提高高分子材料抗张强度和模量...     

Effects of posttreatment on the properties of modified PLLA/PDLA fibers

Poly(L ‐lactic acid)/poly(D ‐lactic acid) (PLLA/PDLA) blended with plasticizer poly(ethylene glycol) and nucleation agent TMC‐306 as‐spun fibers were prepared by melt spinning. The posttreatment was applied by hot drawing at 70°C and then heat‐treating at different temperatures for 30 minutes. In the process of hot drawing, orientation induced the further formation of the sc crystals and increased the degree of crystallinity of drawn fibers. When the hot drawing ratio reached 3 times, the properties of the fibers were relatively better. The highly oriented fibers containing pure sc crystals with high crystallinity were obtained by heat‐treating at a temperature above the melting point of α crystals. The posttreated PLLA/PDLA fibers with poly(ethylene glycol) and TMC‐306 (LDTP) obtained by hot drawing to 3 times at 70°C and then annealing at 170°C for 30 minutes exhibited the best antioxidative degradation and heat resistance properties. The initial decomposition temperature (T_5%) and heat resistance of posttreated LDTP fiber were about 94°C and 20°C higher than those of the commercial PLLA fiber, respectively.     

Formation of β‐iPP in isotactic polypropylene/ethylene–propylene rubber blends: Effects of preparation method,composition, and thermal condition

The effects of preparation method, composition, and thermal condition on formation of β‐iPP in isotactic polypropylene/ethylene–propylene rubber (iPP/EPR) blends were studied using modulated differential scanning calorimeter (MDSC), wide angle X‐ray diffraction (WAXD), and phase contrast microscopy (PCM). It was found that the α‐iPP and β‐iPP can simultaneity form in the melt‐blended samples, whereas only α‐iPP exists in the solution‐blended samples. The results show that the formation of β‐iPP in the melt‐blended samples is related to the crystallization temperature and the β‐iPP generally diminishes and finally vanishes when the crystallization temperature moves far from 125 °C. The phenomena that the lower critical temperature of β‐iPP in iPP/EPR obviously increases to 114 °C and the upper critical temperature decreases to 134 °C indicate the narrowing of temperature interval, facilitating the formation of β‐iPP in iPP/EPR. Furthermore, it was found that the amount of β‐iPP in melt‐blended iPP/EPR samples is dependent on the composition and the maximum amount of β‐iPP formed when the composition of iPP/EPR blends is 85:15 in weight. The results through examining the effect of annealing for iPP/EPR samples at melt state indicate that this annealing may eliminate the susceptibility to β‐crystallization of iPP. However, only α‐iPP can be observed in solution‐blended samples subjected to annealing for different time. The PCM images demonstrate that an obvious phase‐separation happens in both melt‐blended and solution‐blended iPP/EPR samples, implying that compared with the disperse degree of EPR in iPP, the preparation method plays a dominant role in formation of β‐iPP. It is suggested that the origin of formation of β‐iPP results from the thermomechanical history of the EPR component in iPP/EPR. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1704–1712, 2007     

Study on high weld strength of impact propylene copolymer/high density polyethylene laminates

The impact propylene copolymer(IPC)and isotactic polypropylene(iPP)were separately selected to prepare laminates with high density polyethylene(HDPE)by hot press.The peel forces of IPC/HDPE and i’PP/HDPE laminates were examined,and it was found that the welded joint strength in IPC/HDPE laminate was dramatically higher than that of iPP/HDPE laminate.According to the special microstructure of IPC,the co-crystallization of the ethylene segments in ethylene-propylene block copolymer(EbP)component of IPC and the PE chain in HDPE was proposed to explain the high-strength welding.The DSC results indicated that there indeed existed some interaction between IPC and HDPE,and the crystallizable PE component in IPC could affect the crystallization of HDPE.The scanning electron microscope(SEM) observations of IPC/HDPE blends demonstrated that HDPE tended to stay with the PE-rich EbP chains to form the dispersed phase,indicating the good miscibility between HDPE and EbP components of IPC.According to the above results,the effect of co-crystallization of the PE components of the IPC and HDPE on the high weld strength of IPC/HDPE laminate was confirmed.     

Surface Fixing Effect of Vacuum Evaporated Particles on Polyethylene Single Crystals

Summary: The recrystallization behavior of high density polyethylene (HDPE) single crystals with vacuum evaporated metal chromium or carbon on their surface has been investigated by transmission electron microscopy (TEM) and electron diffraction (ED) techniques. The results indicate that the particle‐coated HDPE single crystals can retain their single crystal structure after complete melting and subsequent recrystallization, with the heat‐treated temperature as high as 200 °C. This phenomenon is attributed to a surface fixing effect of vacuum evaporated Cr or carbon on the single crystals.

A bright‐field electron micrograph and the corresponding electron diffraction pattern of recrystallized Cr‐coated HDPE single crystals.     

Effect of environment on the degradation of starch and pro-oxidant blended polyolefins

The aim of this study was to understand the rate of degradation of commercial pro-oxidant blended and starch blended High Density Polyethylene (HDPE), pro-oxidant blended Low Density Polyethylene (LDPE), and starch blended polypropylene in three different environments, namely under direct sunlight, buried in soil and immersed in marine waters for a period of 150 days. The bio-fouling parameters were also monitored in the case of polymers deployed in sea water. Exposure to sunlight showed highest weight loss (>10%) and samples buried in soil showed the lowest (∼1%). Pro-oxidant blended HDPE showed higher weight loss when compared to starch blended (22.7 as against 11%). Scanning electron microscopy revealed surface deterioration and decrease in contact angle indicated reduction in surface hydrophobicity. Increase in the carbonyl and hydroxyl groups in the infra-red spectrum of the exposed samples suggested abiotic degradation. Starch blended PP exposed to sunlight showed the highest thermo gravimetric weight loss (63.8%) followed by the same polymer buried in soil (46.1%).     

Drawing of single-crystal mats of linear polyethylene

Drawing of single-crystal mats of linear polyethylene has been investigated. Drawing is possible at temperatures higher than about 90°C. The drawing is accompanied by distinct necking, with a large decrease in the thickness of the mat and a very high maximum draw ratio, sometimes over 30. The maximum draw ratio is approximately proportional to the thickness of the lamellae. This behavior strongly suggests the unfolding of chains during drawing. A change of orientation of crystal axes occurs before necking without change of lamellar orientation. The a axis orients in the drawing direction; the b axis orients perpendicular to the direction of drawing; and the chain axis tilts away from the thickness direction of the mat. The structure of films drawn from mats is characterized by a distinct double orientation of crystals. This biaxial orientation in the drawn films has a high degree of correlation with the orientation of crystal axes observed before necking, and suggests that necking takes place in such a way that the chain tilts gradually about the b axis and ultimately unfolds. The postulate of formation of transitory two-dimensional crystals in necking seems useful in explaining the double orientation in the drawn film. The orientation behavior of crystal axes observed before necking is not always similar to that observed in the deformation of a single crystal. The difference is thought to be due to the effect of forces induced by drawing that act in the direction normal to the lamellae within a mat.     

Epitaxial and graphoepitaxial growth of isotactic polypropylene (iPP) from the melt on highly oriented high density polyethylene (HDPE) substrates

Although under normal conditions only the crystallization behavior of PE on oriented iPP substrates can be studied due to the higher melting point of iPP, the faster crystallization rate of a molten, oriented HDPE film compared to a nonoriented iPP layer was used to study the crystallization of iPP on the oriented HDPE film by means of transmission electron microscopy (TEM) and electron diffraction (ED). Besides the known epitaxial relationship of HDPE/iPP with their chains 50° apart, two new orientation relationships with (a) chains of both polymers parallel and (hk0)_iPP in contact with the HDPE substrate, and (b) the a‐axis of iPP crystals parallel to the chain direction of HDPE but (001)_iPP in contact with the HDPE substrate were observed. Both orientations are assumed as graphoepitaxy. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1893–1898, 1999     

Morphology of uniaxially oriented poly(ethylene terephthalate)

The morphological character of uniaxially oriented poly(ethylene terephthalate) (PET) films was investigated as a function of draw ratio. Dynamic mechanical, infrared, and crystallite-size measurements were made on the samples. In addition, selective degradation experiments and molecular weight determinations were employed. The dynamic mechanical measurements indicated a sharp decrease in irregular folds for draw ratios of 3.0 and higher, which also coincided with the essentially complete disappearence of regular folds (from the 988 cm^?1 band in the infrared spectra) in unannealed samples. Infrared studies of drawn samples annealed under different conditions gave evidence in support of a structure in which the chains are stretched out. Apparent crystallite-size measurements showed a sudden increase in length of the crystals in the direction of the draw beyond a draw ratio of 3.0. Molecular weight measurements showed a large increase in average chain length in the residue after selective degradation of amorphous material and folds; undrawn and slightly drawn samples gave a much lower M _n. Based on these observations, it is postulated that for higher draw ratios and present drawing conditions, the crystals are of the straight chain type, somewhat similar to the fringed-micelle crystal concept.     

Oriented crystallization of poly(L‐lactic acid) in uniaxially oriented blends with poly(vinylidene fluoride)

This article describes the oriented crystallization of poly(L ‐lactic acid) (PLLA) in uniaxially oriented blends with poly(vinylidene fluoride) (PVDF). Uniaxially drawn films of PLLA/PVDF blend with fixed ends were heat‐treated in two ways to crystallize PLLA in oriented blend films. The crystal orientation of PLLA depended upon the heat‐treatment process. The crystal c‐axis of the α form crystal of PLLA was highly oriented in the drawing direction in a sample cold‐crystallized at T_c = 120 °C, whereas the tilt‐orientation of the [200]/ [110] axes of PLLA was induced in the sample crystallized at T_c = 120 °C after preheating at T_p = 164.5–168.5 °C. Detailed analysis of the wide‐angle X‐ray diffraction (WAXD) indicated that the [020]/ [310] crystal axes were oriented parallel to the drawing direction, which causes the tilt‐orientation of the [200]/ [110] axes and other crystal axes. Scanning electron microscopy (SEM) suggested that oriented crystallization occurs in the stretched domains of PLLA with diameters of 0.5–2.0 μm in the uniaxially drawn films of PVDF/PLLA = 90/10 blend. Although the mechanism for the oriented crystallization of PLLA was not clear, a possibility was heteroepitaxy of the [200]/[110] axes of the α form crystal of PLLA along the [201]/[111] axes of the β form crystal of PVDF that is induced by lattice matching of d₁₀₀(PLLA) ≈ 5d₂₀₁(PVDF). © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1376–1389, 2008     

poly(4,4′-oxybibenzoate): Polymerization,morphology, transitions,and crystal structures

4-Acetoxy 4′-carboxy biphenyl has been polymerized from solution, the bulk melt, and in constrained thin films, all below the melting point of the monomer as measured by differential scanning calorimetry (DSC). An isothermal sublimation–recrystallization–melting (and chemical change)–polymerization–crystallization process is proposed. From solution and in the thin films, single crystals consisting of ca. 100 Å thick lamellae are observed, with evidence for monomer addition–reaction on the end (top and bottom) surfaces. The bulk samples are fibrous, the “fibers” consisting of whisker-like single crystals. The polymer is highly heat and radiation (electron beam) resistant, with numerous successive electron diffraction (ED) patterns from the same crystal or sheared sample permitting comparison of the changes in ED patterns with transitions seen by DSC at ca. 350, 530, and 590°C. Phase I (a = 7.8, b = 5.5, c = 10.8 Å), a possible phase II (a = 15.6, b = 3.6 Å c = unknown), and a phase III (a = 9.0, b = 5.2 = √3a, c = 10.8 Å). Phases I and II are seen in samples polymerized at temperatures at and below 310°C; phase III is observed in samples polymerized at and above 350°C and in sheared samples. © 1993 John Wiley & Sons, Inc.     

Tearing energy study of “oriented and relaxed” polystyrene in the glassy state

To study the effect of processing history, molecular weight/molecular weight distribution, and thermal history on solid state properties (in particular fracture properties and orientation), carefully characterized polydisperse and monodisperse polystyrene samples were drawn above T_g and the orientation frozen in. The objective was to simulate the incidental orientation of polymer chains after processing, molding, and so forth (e.g., injection or compression, blow molding) as a result of melt flow. A series of polystyrene samples was produced by hot drawing at temperatures of 113 and 148 °C, followed by a relaxation period, and then a quench to below T_g. The level of segmental orientation imposed in the samples was determined by birefringence measurements. The tear energy of the sheets was measured at 20 °C by tearing along the draw direction, ultimately giving a value for the fracture energy, G_3C. Samples of high draw ratio and low segmental orientation were unexpectedly found to have highly anisotropic fracture properties despite the low level of optical anisotropy. The fracture properties also depended significantly on whether the samples were drawn with or without lateral constraint. The results are compared with measurements of isotropic samples and the findings of a previous investigation utilizing SANS and birefringence. Modeling the drawing conditions at the chain level using a recent nonlinear tube theory explains how birefringence alone is an inadequate measure of molecular orientation. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 377–394, 2007     

Drawing behavior of linear polyethylene. II. Effect of draw temperature and molecular weight on draw ratio and modulus

The drawing behavior of linear polyethylene homopolymers with weight-average molecular weights (M?_w) from 101,450 to ca. 3,500,000 has been studied over the temperature range 75°C to the melting point. In all cases 1-cm gauge length samples were drawn in an Instron tensile testing machine at a constant cross-head speed of 10 cm/min. With the exception of the lowest molecular weight polymer, it was found that increasing the draw temperature led to substantial increases in the maximum draw ratio which could be achieved, and that this increased monotonically with increasing draw temperature. Measurements of the Young's modulus of the drawn materials showed, however, that the unique relationship between modulus and draw ratio previously established for drawing at 75°C was not maintained to the highest draw temperatures. The highest draw temperature at which this relation held was found to be strongly molecular weight dependent, increasing from ca. 80 to ca. 125°C when M?_w increased from 101,450 to 800,000. In all cases conditions could be found for drawing samples to draw ratios of 20 or more with correspondingly large values of the Young's modulus.     

Characterization of PP/HDPE blend-based nanocomposites using different maleated polyolefins as compatibilizers

Nanocomposites based on a polypropylene (PP)/high density polyethylene (HDPE) blend were prepared using an organo-montmorillonite (15A) as a nano-filler and two maleated polyolefins (PE-MA and PP-MA) as compatibilizers. The phase morphology and typical physical properties of the prepared samples were examined. The nano-filler 15A was intercalated and/or partially exfoliated in the blend when PE-MA or PP-MA was present. The PE-MA facilitated the dispersibility of 15A to a better degree. The nano-filler 15A accelerated the crystallization of PP in the blends, whereas it hardly influenced the crystallization of HDPE. Moreover, at a slow cooling rate (i.e., 1 °C/min) the PP-MA induced a higher crystallization temperature for PP in the composite, while PE-MA impeded PP crystallization. On the other hand, the crystallization of HDPE in the composite was only slightly influenced by the presence of PE-MA or PP-MA. The thermal stability of PP/HDPE blend was enhanced after the addition of 15A regardless of the inclusion or not of PE-MA or PP-MA. The enhancement was more evident when the samples were scanned under an air environment than a N2 environment. The stiffness of PP/HDPE blend increased marginally after adding 15A and was slightly altered with the further inclusion of PP-MA. The presence of PE-MA in the composite caused a slight decline in the stiffness. The impact strength of PP/HDPE blend declined after the formation of nanocomposites, especially for the sample incorporating PP-MA.     

Miscibility and transesterification in ternary blends of poly(ethylene naphthalate)/poly(trimethylene terephthalate)/poly(ether imide)

Miscibility and morphology of poly(ethylene 2,6-naphthalate)/poly(trimethylene terephthalate)/poly(ether imide) (PEN/PTT/PEI) blends were investigated by using a differential scanning calorimeter (DSC), optical microscopy (OM), wide-angle X-ray diffraction (WAXD), and proton nuclear magnetic resonance (¹H-NMR). In the ternary blends, OM and DSC results indicated immiscible properties for polyester-rich compositions of PEN/PTT/PEI blends, but all compositions of the ternary blends were phase homogeneous after heat treatment at 300 °C for more than 30 min. An amorphous blend with a single T _g was obtained in the final state, when samples were annealed at 300 °C. Experimental results from ¹H-NMR identified the production of PEN/PTT copolymers by so-called “transesterification”. The influence of transesterification on the behaviors of glass transition and crystallization was discussed in detail. Study results identified that a random copolymer promoted the miscibility of the ternary blends. The critical block lengths for both PEN and PTT hindered the formation of crystals in the ternary blends. Finally, the transesterification product of PEN/PTT blends, ENTT, was blended with PEI. The results for DSC and OM demonstrated the miscibility of the ENTT/PEI blends.     

Plastic deformation of highly drawn polypropylene monofilaments

The tensile properties of highly oriented polypropylene (PP) filaments are markedly dependent on their fabrication drawn history. Highly oriented filaments prepared by drawing at <100°C were capable of appreciable plastic deformation after passing through a marked yield point. This deformation process was very rate dependent, transforming to essentially brittle behavior at deformation rates >500%/min. Filaments produced by drawing at a higher temperature, or by annealing above 100°C of those produced at 100°C, had a slightly lower modulus, greatly reduced residual elongation to break, and showed no yield point. A model for the plastic deformation is proposed involving localized fibrillation to produce craze-like structures. This model is consistent with the observed filament susceptibility to chromic acid etching. Electron micrographs of highly drawn then etched samples show that just prior to fracture only small plastes of the acid resistant (presumably original, unvoided) structure remain.     

Morphology development during isothermal crystallization. II. Isotactic and syndiotactic polypropylene blends

Morphology development during isothermal crystallization in equal molecular weight isotactic polypropylene (iPP), syndiotactic polypropylene (sPP), and iPP/sPP blends was studied with time‐resolved simultaneous small‐angle X‐ray scattering (SAXS) and wide‐angle X‐ray diffraction (WAXD) with synchrotron radiation. The sPP melting point is 15–20 °C below that of the iPP component, and sPP multiple melting is not affected by blending for 50–100 wt % sPP compositions. SAXS and WAXD (at 115 and 137.5 °C) show that sPP crystallizes more slowly than iPP. The sPP long spacing is larger than that of iPP at both crystallization temperatures, exhibits a broader distribution, and changes to a greater extent during crystallization. Differential scanning calorimetry (DSC) cooling and SAXS/WAXD measurements show iPP crystallizing first and nearly to completion before sPP in a 50:50 iPP/sPP blend. At 115 °C, iPP crystals nucleate sPP in a 50:50 blend and modify the sPP lamellar spacing. The nucleation does not overcome the large difference in the iPP and sPP rates at 137.5 °C. Before sPP crystallization in a 50:50 blend (115 °C), the iPP long spacing is not affected by molten sPP. The iPP long spacing is slightly expanded by molten sPP, and the WAXD induction time is delayed at 137.5 °C. The observed iPP long spacing in the presence of molten sPP is consistent with previously reported results for iPP/atactic polypropylene (aPP) blends of similar molecular weight. Quantitative differences between the two types of blends are consistent with previously reported thermodynamic rankings. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1876–1888, 2001     

Structure and mechanical properties of talc‐filled blends of polypropylene and styrenic block copolymers

The structure–property relationships of isotactic polypropylene (iPP)/styrenic block copolymer blends filled with talc were examined by optical and scanning electron microscopy, wide‐angle X‐ray diffraction, and tensile‐ and impact strength measurements. The composites were analyzed as a function of the poly(styrene‐b‐ethylene‐co‐propylene) diblock copolymer (SEP) and the poly(styrene‐b‐butadiene‐b‐styrene) triblock copolymer (SBS) content in the range from 0 to 20 vol % as elastomeric components and with 12 vol % of aminosilane surface‐treated talc as a filler. Talc crystals incorporated in the iPP matrix accommodated mostly plane‐parallel to the surface of the samples and strongly affected the crystallization process of the iPP matrix. The SBS block copolymer disoriented plane‐parallel talc crystals more significantly than the SEP block copolymer. The mechanical properties depended on the final phase morphology of the investigated iPP blends and composites and supermolecular structure of the iPP matrix because of the interactivity between their components. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1255–1264, 2004