Mixed monolayers of polymethacrylic esters containing aromatic and aliphatic groups

The interfacial properties of mixtures of polymethacrylic polymers containing either aromatic or aliphatic side groups were studied at water-air interface in order to define the role of geometrical orientation on surface compatibility and the effect of aromatic interactions on ordered bidimensional systems. Two binary systems were studied: polyphenylmethacrylate/ polyhexylmethacrylate and polyphenylmethacrylate/polybenzylmethacrylate.Surface pressure and surface potential measurements were performed in the 288–303 K temperature range on the mixtures at different polymer concentrations. Further information was obtained from ellipsometric measurements and scanning electron microscopy of the collapsed material. The experimental results allow for the conclusion that both polymers containing aromatic groups are almost ideally miscible whereas mixtures of aliphatic and aromatic polymers are completely immiscible.     

Spontaneous film formation from a polymer solution

An unusual continuous film formation process of lateral pentyloxy substituted poly(p-phenylene terephthalate)s (s-PPPT) and poly(carbonate) (PC) is observed. A liquid film of polymer solution creeps over the surface of water dropped into the polymer solution. By vaporization of the solvent a solid polymer film is formed on the water surface and can be removed. The driving force for the film formation mechanism is assumed by the reduction of the surface tension of water. Experiments verify this mechanism by increasing the film formation speed using a gas stream, by reducing the formation speed through lowering the surface tension by rinsing agents, and by lowering the solubility of the polymer. As expected, no effects are found by variation of the pH-value of water. Necessary conditions for the film formation process are: good solubility of the polar polymers in organic solvents having a high vapor pressure, complete phase separation, solution density higher than water density, and a surrounding gas phase unsaturated with solvent vapor.The thickness of the mechanically stable films is less than 0.5 m. The films are amorphous by microscopical, FT-IR, x-ray, and DTA investigations.     

Effect of protein content on the surface activity and viscosity of emulsan

Emulsan, produced byAcinetobacter calcoaceticus RAG-1, consists of a lipoheteropolysaccharide-protein complex. The amount of protein in the complex depends on the purification procedure. Maximum hexadecane-in-water emulsifying activity of emulsan was obtained with preparations containing 8–16 % protein. Neither deproteinized preparations (apoemulsan) nor protein-rich preparations emulsified hexadecane-in-water; however, mixtures of these preparations (containing 10–15 % total protein) were potent emulsifiers.Emulsifying activity was also obtained with a mixture of apoemulsan and polysaccharide-free emulsan protein. The stimulatory role of protein in the activity of emulsan was also demonstrated by pronase treatment of the complex. The presence of protein in the complex was important for lowering interfacial tension between hexadecane and water. Apoemulsan solutions showed _i values of 30 mN/m whereas, emulsan containing more than 6% protein showed values of 13–15 mN/m. Viscosity studies showed that: (i) The higher the protein content in the complex, the lower its intrinsic viscosity, indicating that association of protein with the polysaccharide backbone results in less extended conformation; (ii) the complex appears to be stable between 30 ° and 80 °C; and (iii) mixtures of apoemulsan and emulsan had intrinsic viscosities close to the value predicted from addition of the weight-fraction contribution of the individual components. The synergistic emulsifying activity of emulsan mixtures is explained in terms of surface tension lowering by the protein component and formation of stable interfacial films by the high molecular weight polysaccharide component.Preliminary results of this work were presented at the 5th International Conference on Surface and Colloid Science, Potsdam, N.Y., June 1985.     

Effect of polymerized silicic acid on mixed lipid-protein monolayers used as cell membrane models. I. Hemoglobin-stearoyl erythroceramide films

The effect of polysilicic acid on mixed monolayers of hemoglobin and stearoyl erythroceramide used as cell membrane models has been studied. The presence of the sphingolipid at the interface stabilizes the hemoglobin monolayer, hindering expulsion of its residues from the surface when the collapse pressure (ca. 23 mN/m) is reached. The interaction between the components of the mixed film results in non-additivity of their molecular areas to a degree depending on film composition and substrate pH. The presence of polysilicic acid in the substrate increases the miscibility of the components in the mixed monolayer as a result of ionic interaction between the silicic acid and the protein.     

Mechanical and morphological investigations of UHMWPE/Fe composites

Ultra-high molecular weight polyethylene/iron composites were investigated. The specimens were obtained by pressing in a steel die and sintering at different temperatures. By means of porosimetry, microscopy, microhardness, density, and partial volumes of the components it is shown that there are no microcavities. The microhardness does not depend upon the weight % content of the metal in the composites. It also neither depends on the pressure nor the temperature of sintering. For low metal content within the composites, microhardness Mayer equations are linear. For high metal content the dependence is nonlinear. With the increasing of the iron content tensile strength weakly decreases. However, plane-strain compression, dimension steadiness, Vicat softening temperature, and tribometric characteristics of the composites are improved. It is shown that the polymer is a well-dispersive medium. The particles of the components have a good mechanical compatibility. The polymer wets the surface of the iron; this is probably connected with the surface oxidation of the metal particles.     

A monolayer model of the interfacial region of microemulsions

Mixed monolayers of tetradecanol and oleic acid at the water-air interface were studied to provide a static related structure featuring the interface between water and oil of water-dodecane microemulsions.The films of pure components as a function of temperature show a strong area contraction between 25 ° and 30 °C, caused by a change in the head groups hydration. This agrees with similar discontinuities found for some properties of the microemulsion in the same temperature range. At the water-air interface, the composition range of tetradecanol/oleic acid mixtures with the highest thermodynamic stability corresponds to the same stability range of the water-in -dodecane-potassium oleate microemulsions.Adsorption isotherms of tetradecanol and hexanol at the dodecane-water interface were studied to compare the surface behaviour of the two alcohols; the results indicate that the two alcohols have very similar two-dimensional surface phases and adsorption energies.     

Preparation of asymmetric polymer film by emulsion blend technique

Two kinds of anionic polymer emulsions, of which particle sizes were greatly different, were blended and then cast on a release-paper at 30 °C. One was poly(butyl acrylate) emulsion, 0.46n in diameter, produced by emulsifier-free emulsion polymerization, and the other was ethyl acrylate-methyl methacrylate (1/1, mole ratio) copolymer emulsion, 0.02m in diameter, produced by emulsifier-containing emulsion polymerization. The film produced had asymmetric surface properties: the air-side surface was nontacky and the bottom-side surface was tacky. The forming mechanism is discussed.     

Degradation behaviors of polyester monolayers at the air/water interface: Alkaline and enzymatic degradations

The degradation kinetics of Langmuir monolayer films of a series of biodegradable polyesters has been studied to investigate the effect of degradation medium, alkalinity and enzymes. The degradation behavior of polyester monolayers strongly depended on both degradation medium and surface pressure. As the surface pressure was increased, the degradation rates of poly(l-lactide) (PLLA) and poly[(R)-3-hydroxybutyrate] (P(3HB)) increased in both degradation media. When monolayers were exposed to an alkaline subphase, the degradation of PLLA monolayers occurred at relatively low surface pressures; the PLLA monolayers were hydrolyzed at pH 10.5 regardless of surface pressure, while the alkaline degradation of P(3HB) monolayer occurred over a constant surface pressure of 7 mN/m at pH 11.8. These results have been explained by the difference in hydrophilic/hydrophobic balance of the polymers; PLLA is more hydrophilic than P(3HB). In contrast, the enzymatic degradations of both polymer monolayers occurred at higher constant surface pressures than those of the alkaline treatment; 7 mN/m for PLLA and 10 mN/m for P(3HB). This behavior was attributed to the enzymes being much larger than the alkaline ions: the enzymes need a larger contact area with the submerged monolayers to be activated.     

Determination of dispersive and nondispersive components of the surface free energy of glass fibers

The dispersive component _s ^d of the surface free energy of glass fibers and its interaction energy with alkanes, benzene, 1-nitropropane, ethyleneglycol, glycerol, formamide, and water were quantitatively determined by the tensiometric method within two liquids. The values of nondispersive interaction energy I _SL ^p were found to be a linear function of the square root of the nondispersive component of the surface free energy of liquids. This suggests that the nondispersive interaction energy may be represented by the geometric mean of the nondispersive component of the surface free energy of a solid and a liquid. The slope gave the nondispersive component _s ^p of the surface free energy. The _s ^p values are 33 and 14 mJ/m² for the untreated and aminosilane-treated fibers, respectively, suggesting that organophilic character has developed on the surface after aminosilane treatment. The _s ^p value was almost similar after the treatment, probably because of the polar characteristics of amino groups.     

嵌入花生酸镉单层中的卟啉-紫精分子聚集行为的研究

本文制备了卟啉-紫精与花生酸镉混合LB膜, 用紫外可见光谱研究了膜中卟啉基团的聚集及取向, X射线衍射说明混合LB膜具有层状有序的周期结构。扫描电镜结果表明: 通过调节膜的表面压可使聚集成"微畴"的卟啉-紫精均匀分布在花生酸镉单分子层中, 随膜表面压的增大, 小的"微畴"相互连接形成更大的"微畴"。电子衍射说明混合膜中两组份分相存在, 且都为六角对称的有序结构。     

The influence of vegetable oils on biosurfactant production by Serratia marcescens

The production of biosurfactant, a surface-active compound, by two Serratia marcescens strains was tested on minimal culture medium supplemented with vegetable oils, considering that it is well known that these compounds stimulate biosurfactant production. The vegetable oils tested included soybean, olive, castor, sunflower, and coconut fat. The results showed a decrease in surface tension of the culture medium without oil from 64.54 to 29.57, with a critical micelle dilution (CMD⁻¹) and CMD⁻² of 41.77 and 68.92 mN/m, respectively. Sunflower oil gave the best results (29.75 mN/m) with a CMD⁻¹ and CMD⁻² of 36.69 and 51.41 mN/m, respectively. Sunflower oil contains about 60% of linoleic acid. The addition of linoleic acid decreased the surface tension from 53.70 to 28.39, with a CMD⁻¹ of 29.72 and CMD⁻² of 37.97, suggesting that this fatty acid stimulates the biosurfactant production by the LB006 strain. In addition, the crude precipitate surfactant reduced the surface tension of water from 72.00 to 28.70 mN/m. These results suggest that the sunflower oil’s linoleic acid was responsible for the increase in biosurfactant production by the LB006 strain.     

Spinodal decomposition of the polymer blend deutereous polystyrene (d-PS) and polyvinylmethylether (PVME) studied with high resolution neutron small angle scattering

Decomposition of a polymer blend in the miscibility gap has been studied by small angle scattering of neutrons, using a double crystal diffractometer. It covers a range of 10^–5 to 10^–3 Å^–1, which connects the region of elastic light scattering and, at the upper end, the region of conventional neutron small angle scattering instruments. The decomposed structure in the miscibility gap can be described by a characteristic lengthR which increases with time,t ^1/3 between 7 and 25 min. At longer times, the growth follows a more linear power law. This behaviour is consistent with predictions of the domain growth for liquid mixtures and is estimated by using the self diffusion constant, viscosity, and the surface energy of the polymer.on leave ESFM-IPN Mexico     

Phase and miscibility behavior of binary lipid systems

Differential scanning calorimetry was applied to study the phase diagrams of the following binary lipid systems: myristic acid (C₁₃COOH) / pentadecanoic acid (C₁₄COOH); palmitic acid methyl ester (C₁₅COOMe) / heptadecanoic acid methyl ester (C₁₆COOMe); palmitic acid methyl ester (C₁₅COOMe) / stearic acid methyl ester (C₁₇COOMe); palmitic acid methyl ester (C₁₅COOMe) / arachidic acid methyl ester (C₁₉COOMe). A distinct succession in the phase diagram types and phase regions was observed, according to the chemical structure of the mixing components.In the systems C₁₃COOH/C₁₄COOH; C₁₅COOMe/C₁₆COOMe and C₁₆COOMe/ C₁₇COOMe, both components are completely miscible in the low- and high-temperature phase. Contrasting with these three binary lipid systems, the system C₁₅COOMe/ C₁₄COOMe shows complete miscibility only in the high-temperature phase, but almost complete demixing in the solid state. In the phase diagram an incongruent melting 11 complex is built up. This complex forms an eutectic mixture with the phase of C₁₅COOMe and a peritectic system with C₁₉COOMe.     

Deposition of polymer latices on grafted Nylon 6 fiber

Deposition of polymer latices on a grafted Nylon 6 fiber was studied as a function of pH and the degree of grafting. The latices were polystyrene (PS), styrene/acrylamide copolymer (P(St/AAm)) and styrene/acrylic acid copolymer (P(St/AA)). The deposition of the latices on the grafted fiber decreased in every case with increasing pH and no deposition was observed at alkaline pH. The grafting of fiber with acrylic and methacrylic acid reduced the deposition of P(St/AAm) and P(St/AA) latices but had no influence on the deposition of PS latex. The relation between the deposition rates and the interaction energy at acidic pH indicates that the deposition of PS latex on the grafted fiber mainly depends on the electrostatic interaction. These results suggest that the expansion of water-soluble polyelectrolyte layer on the surface of grafted fiber plays an important role on the deposition.     

Surfactant monolayers on a clean mercury surface: Apparatus and experiments

A Langmuir trough for studying monolayers on a mercury surface was constructed usingT. Smith's design. The surfactant (long-chain alkyl-trimethylammonium compounds) in aqueous solution were spread on a clean mercury surface in an atmosphere of helium, and the surface pressure re-areaA and thickness of surface filmd-areaA curves were obtained. The-A curves were characterized by the appearance of multiple inflection points and plateaus, being explained as stepwise dense surface packing of molecules, and the formation of multilayers by film compression with long axes of molecules lying flat on the mercury surface.     

Discussion of craze formation and growth in amorphous polymers in terms of the multiplicity of glass transition at low temperatures

A craze, the typical deformation zone in an amorphous polymer, can be divided into a precraze and a proper craze. A better understanding of the two corresponding formation processes is possible in terms of glass transition multiplicity.The precraze is associated with the molecular mobility in the confined flow zone, which is part of the main transition. The proper craze corresponds to the mobility in the flow transition zone (terminal zone for shear). A negative pressure generated by nonuniaxial stress is considered to be important for the maintainance of the molecular mobility in these zones belowT _g . The behavior of the zones at negative pressure and low temperatures Tg is considered using a pressure-temperature diagram. The fibril structure of crazes is discussed by a defect diffusion model for the proper glass transition; it is correlated with the sequential physical aging of the corresponding frozen structural defects. Typical mode lengths of the molecular mobilities in the different zones are compared with typical craze parameters. The structure of the craze material is considered to result from confined flow processes which cannot percolate because in the main transition the flow is confined by entanglements, and in the flow transition zone the flow is stopped by releasing the negative pressure due to crack propagation.     

Characterization of wood fibers modified by phenol-formaldehyde

Wood-fiber phenol-formaldehyde-resin (PFR) modified surfaces, obtained from the adsorption of a PFR/water solution, are investigated as a function of the nature and the amount of PFR adsorbed. Surface are measurements are performed by using krypton adsorption at 77 K. Chemical modification is monitored by the electron spectroscopy for chemical analysis (ESCA) technique and the surface energy by the inverse phase gas chromatography (IPGC) method at infinite dilution. The London dispersive componentγ _S ^L of the surface energy shows a relationship to the concentration of carbon and oxgen at the fiber surface.γ _S ^L increases from 27.5 mN·m⁻¹ for the untreated fiber to 42.5 mN·m⁻¹ for the fibers treated with 20% high molecular-weight-grade phenol-formaldehyde. The surface atomic ratio O/C determined using the ESCA technique exhibits a decrease from 44% for untreated to 31% for treated samples. Surface area also decreases from 2.09 m²/g to 1.50 m²/g. The PFR adsorbed by wood fibers is observed as the dispersive component of surface energy starts to increase, as the surface oxygen concentration decreases, and on the surface area of the wood fiber.     

Polypeptides mixed monolayers: collapse mechanism

The mechanism of the collapse process of monolayers of poly-L-alanine and of its mixtures with poly--methyl-L-glutamate was studied at the water/air interface at temperatures of 15°, 20°, 25°, and 30 °C.From measurements of the collapse surface pressure as a function of molar ratios and from the determination of the collapse kinetics, as well as from ellipsometrical measurements of the thickness of the film, the complete solubility of the components, even in the collapsed phase, was deduced.Furthermore, activation energies and values ofG*,H*, andS* in relationship to the kinetics of this process were deduced; it was shown that this process is constituted of a first phase of nucleation and of a second phase of growth both for the poly-L-alanine alone and for its mixtures with poly--methyl-L-glutamate.     

Reversible aggregation Part 2. Kinetics of reversible aggregation

The aggregation of two large (5.1 and 2.6 m diameter) polymer latices was examined microscopically under perikinetic conditions. The aggregates formed were not rigid, and aggregation was reversible under some conditions. The kinetic behavior was followed by monitoring the relative concentrations of single particles and doublets during aggregation. The results were not consistent with Smoluchowski's theory of irreversible aggregation, but could be described by means of a set of mass action equations. Four simple models were used to describe the dissociation processes. The experimental results indicated that the most appropriate model depended on the electrolyte concentration and the dispersion used.     

Polymethylmethacrylate and stearic acid compatibility in monolayers

Mixed monolayers of polymethylmethacrylate (PMMA) and stearic acid (SA) on substrates with different pH are examined at 25 °C.The spreading isotherms of the pure components and their mixtures in different molar ratios indicate a critical pH value of the support, above which the components are miscible.This limiting pH value, which is confirmed also by surface potential measurements, allows a sufficient ionization of the carboxilic acid.This study was supported by CNR and MPI.