Comparison of SSI with APCI as an interface of HPLC-mass spectrometry for analysis of a drug and its metabolites

Sonic spray ionization (SSI) was compared with atmospheric pressure chemical ionization (APCI) as an interface of high-performance liquid chromatography (HPLC)-mass spectrometry (MS) for sensitive analyses of a neuroleptic drug, haloperidol and its two metabolites, such as reduced haloperidol and 4-(4-chlorophenyl)-4-hydroxypiperidine (CPHP), in biological samples. For both SSI and APCI interfaces, HPLC-MS-MS gave higher sensitivity than HPLC-MS. The sensitivities by HPLC-SSI-MS-MS for haloperidol and reduced haloperidol were 100 and 30 times higher, respectively, than those by HPLC-APCI-MS-MS; no spectrum with recognizable peaks was obtained for CPHP with the APCI interface. Therefore, detection limits and regression equations were examined by the HPLC-SSI-MS-MS for human plasma and urine samples spiked with the above drug and its metabolites. Haloperidol, reduced haloperidol, and CPHP showed good linearity in the ranges of 5-800, 10-800, and 100-800 ng/mL, respectively, for both human plasma and urine; their detection limits were 2.5, 5, and 75 ng/mL, respectively, using a new polymer HPLC column which enabled direct application of biological samples.     

Assessment of the various ionization methods in the analysis of metal salen complexes by mass spectrometry

Metal salen complexes are one of the most frequently used catalysts in enantioselective organic synthesis. In the present work, we compare a series of ionization methods that can be used for the mass spectral analysis of two types of metalosalens: ionic complexes (abbreviated as Com⁺X^?) and neutral complexes (NCom). These methods include electron ionization and field desorption (FD) which can be applied to pure samples and atmospheric pressure ionization techniques: electrospray ionization (ESI), atmospheric pressure chemical ionization (APCI) and atmospheric pressure photoionization (APPI) which are suitable for solutions. We found that FD is a method of choice for recording molecular ions of the complexes containing even loosely bonded ligands. The results obtained using atmospheric pressure ionization methods show that the results depend mainly on the structure of metal salen complex and the ionization method. In ESI spectra, Com⁺ ions were observed, while in APCI and APPI spectra both Com⁺ and [Com + H]⁺ ions are observed in the ratio depending on the structure of the metal salen complex and the solvent used in the analysis. For complexes with tetrafluoroborate counterion, an elimination of BF₃ took place, and ions corresponding to complexes with fluoride counterion were observed. Experiments comparing the relative sensitivity of ESI, APCI and APPI (with and without a dopant) methods showed that for the majority of the studied complexes ESI is the most sensitive one; however, the sensitivity of APCI is usually less than two times lower and for some compounds is even higher than the sensitivity of ESI. Both methods show very high linearity of the calibration curve in a range of about 3 orders of magnitude of the sample concentration. Copyright © 2014 John Wiley & Sons, Ltd.     

APCI as an innovative ionization mode compared with EI and CI for the analysis of a large range of organophosphate esters using GC‐MS/MS

Organophosphate esters (OPEs) are chemical compounds incorporated into materials as flame‐proof and/or plasticizing agents. In this work, 13 non‐halogenated and 5 halogenated OPEs were studied. Their mass spectra were interpreted and compared in terms of fragmentation patterns and dominant ions via various ionization techniques [electron ionization (EI) and chemical ionization (CI) under vacuum and corona discharge atmospheric pressure chemical ionization (APCI)] on gas chromatography coupled to mass spectrometry (GC‐MS). The novelty of this paper relies on the investigation of APCI technique for the analysis of OPEs via favored protonation mechanism, where the mass spectra were mostly dominated by the quasi‐molecular ion [M + H]⁺. The EI mass spectra were dominated by ions such as [H₄PO₄]⁺, [M–R]⁺, [M–Cl]⁺, and [M–Br]⁺, and for some non‐halogenated aryl OPEs, [M]^+● was also observed. The CI mass spectra in positive mode were dominated by [M + H]⁺ and sometimes by [M–R]⁺, while in negative mode, [M–R]⁻ and more particularly [X]^‐ and [X₂]^‐● were mainly observed for the halogenated OPEs. Both EI and APCI techniques showed promising results for further development of instrumental method operating in selective reaction monitoring mode. Instrumental detection limits by using APCI mode were 2.5 to 25 times lower than using EI mode for the non‐brominated OPEs, while they were determined at 50‐100 times lower by the APCI mode than by the EI mode, for the two brominated OPEs. The method was applied to fish samples, and monitored transitions by using APCI mode showed higher specificity but lower stability compared with EI mode. The sensitivity in terms of signal‐to‐noise ratio varying from one compound to another. Copyright © 2016 John Wiley & Sons, Ltd.     

Principle and analytical applications of resonance lonization mass spectrometry

Resonance ionization mass spectrometry (RIMS) is a very sensitive analytical technique for the detection of trace elements. This method is based on the excitation and ionization of atoms with resonant laser light followed by mass analysis. It allows element and, in some cases, isotope selective ionization and is applicable to most of the elements of the periodic table. A high selectivity can be achieved by applying three step photoionization of the elements under investigation and an additional mass separation for an unambiguous isotope assignment.An effective facility for resonance ionization mass spectrometry consists of three dye lasers which are pumped by two copper vapor lasers and of a linear time-of-flight spectrometer with a resolution better than 2500. Each copper vapor laser has a pulse repetition rate of 6.5 kHz and an average output power of 30 W.With such an apparatus measurements with lanthanide-, actinide-, and technetium-samples have been performed. By saturating the excitation steps and by using autoionizing states for the ionization step a detection efficiency of 4 × 10^–6 and 2.5 × 10^–6 has been reached for plutonium and technetium, respectively, leading to a detection limit of less than 10⁷ atoms in the sample. Measurements of isotope ratios of plutonium samples were in good agreement with mass-spectrometric data. The high elemental selectivity of the resonance ionization spectrometry could be demonstrated.Presented in part at the 1989 European Winter Conference on Plasma Spectrochemistry, Reutte, Austria     

Determination of ketamine and metabolites in urine by liquid chromatography-mass spectrometry

We have developed an analytical method by using liquid chromatography-mass spectrometry (LC-MS) to determine ketamine and its metabolites in urine. The ionization efficiency between two ionization modes (ESI and APCI) of LC-MS was compared to each other. An easy and simple sample preparation of urine samples was made by passing samples through a 0.22 μm PVDF syringe filter. The results indicated that the ionization efficiency of positive APCI mode is better than positive ESI mode for determination of trace ketamines. A wide linearity range of the research is from 5 to 250 ng mL⁻¹ and the detection limits for ketamine, norketamine and dehydronorketamine were 0.95, 0.48 and 0.33 ng mL⁻¹, respectively. The proposed method was tested by analyzing ketamine and metabolites in the urines of volunteers. The concentrations of ketamine, norketamine and dehydronorketamine are ranged of 5.4-131.0, 12.5-74.1 and 22.8-278.9 ng mL⁻¹, respectively and the ketamines concentration profiles in human urine were also determined. The results demonstrate the suitability of liquid chromatography-mass spectrometry approach to analyze trace amount of ketamine and its metabolites in urine.     

Simultaneous Determination of Carbamate and Organophosphorus Pesticides in Honeybees by Liquid Chromatography-Mass Spectrometry

Summary The potential of liquid chromatography-mass spectrometry (LC-MS) has been studied for the simultaneous determination of sixteen carbamate and organophosphorus pesticides in honeybees using a traditional sample preparation protocol based on acetone extraction and dichloromethane partitioning. The performances of both atmospheric pressure chemical ionization (APCI) and electrospray (ES) interfaces were compared. APCI offered better sensitivity and specificity for a higher range of pesticides. Limits of quantification were from 0.01 to 0.17 mg kg^–1, at which recoveries obtained were between 64 and 93%, except for pirimicarb that was at 13%, with relative standard deviations ranging from 7 to 20%. Fenitrothion, fenoxycarb, methiocarb and phoxim were found in bees from Valencian Community beehives at concentrations between 0.03 and 3.75 mg kg^–1.     

Ionization mechanism in gel permeation chromatography mass spectrometry (GPC-MS) with atmospheric pressure chemical ionization (APCI) interface

The ionization mechanism in gel permeation chromatography (GPC) coupled with mass spectrometry (MS) using an atmospheric pressure chemical ionization (APCI) interface is explained when chloroform is used as GPC solvent. The even electron anions [CHCl₃+Cl]^? generated by thermal electrons in negative APCI mode are responsible for further ionization of the solute compounds as [M?+?Cl]^? adducts. In positive APCI mode, the contaminants in chloroform generate a relatively high background noise. These cations can be suppressed by adding 10% of tetrahydrofuran (THF). Supporting the described mechanism are key experiments done in the absence of solvent, in GPC solvents and using a mixture of anionic polystyrene (PS) standards from dimer up to 12,000?g/mol, covering the molecular masses of great interest in studies related to Registration, Evaluation, Authorization, and Restriction of Chemicals (REACH) and Food and Drug Administration (FDA). Advantages of suppressing the oligomer signals for polymer additive analyses were presented using Irgafos^® 168.     

Nebulization ionization and desorption ionization analysis of reactive organofunctionalized silanes in nanofilm products

Three different and recently developed desorption ionization techniques, transmission-mode desorption electrospray ionization (TM-DESI), low temperature plasma (LTP) ionization and nano-assisted laser desorption ionization (NALDI), are compared with electrospray ionization (ESI) and atmospheric pressure chemical ionization (APCI) for the analysis of two nanofilm products (NFPs) for surface coating, which contain hydrolysates and condensates of organo-functionalized silanes. The NFPs were characterized in different states from the liquid phase to the fully formed surface film. The LTP spectra were dominated by the silanes, while the corresponding di-, tri- and tetrasiloxanes were common in ESI, APCI and TM-DESI. This indicates readily condensation of the silanes during the ESI and APCI ionization processes leading to the observed siloxanes. NALDI showed larger siloxane structures than the other techniques, indicating film formation on the NALDI target. Real-time monitoring of the film formation on a glass surface by LTP showed a decreasing abundance of the silanes, while the abundances of the di-, tri and tetrasiloxanes increased significantly within the first 100 s. LTP was superior in showing the non-reacted content of the NFPs, while ESI, APCI and TM-DESI were characterized by artefact formation of siloxanes. NALDI was ideal for showing the siloxane structures of the formed film. The applicabilities of each of the ionization techniques were examined, showing the advantage of utilizing more than one ionization technique for the analysis of reactive species.     

Determination of steroids by liquid chromatography/mass spectrometry

On-line atmospheric pressure chemical ionization (APCI) and electrospray ionization (ESI) liquid chromatography/mass spectrometry (LC/MS) were evaluated for the analysis of a variety of steroids. Steroids were classified into three major groups based on the spectra and the sensitivities observed: (I) those containing a 3-one, 4-ene functional group, (II) those containing at least one ketone group without conjugation, and (III) those containing hydroxy group(s) only. In the APCI mode, the best sensitivity and the lowest detection limit for all three groups were obtained by using a mobile phase consisting of methanol and 1%–2% acetic acid in water. The APCI spectra were characterized by MH⁺, MH⁺-H₂O, MH⁺-2H₂O, etc., with the degree of H₂O loss being compound dependent: group I steroids produced stable MH⁺ and group III steroids showed extensive water loss. In the electrospray mode the best sensitivity and the lowest detection limit for the first two groups were obtained when pure methanol and water were used as the mobile phase. This condition produced abundant stable MNa⁺ due to ubiquitous sodium. Detection limits in the 5–15 pg range can be easily achieved using ESI LC/MS. Addition of ammonium acetate or use of acetonitrile in the mobile phase, common in the LC/MS analysis of steroids, decreased the sensitivity for the group I and II steroids and thus should be avoided. For group III steroids, the detection limit can be improved by the addition of acetic acid to the mobile phase.     

Application of atmospheric pressure ionization HPLC-MS-MS for the analysis of natural products

Summary The development of techniques utilizing atmospheric pressure ionization, namely atmospheric pressure chemical ionization (APCI) and electrospray ionization (ESI), has pioneered the coupling of liquid chromatography (HPLC) with mass spectrometry in recent years. Both ESI and APCI generate ions from polar and labile biomaterials with remarkable ease and efficiency. In particular, the use of HPLC with tandem mass spectrometry (MS-MS) opens further dimensions in the field of bioorganic analysis. Thus, HPLC-MS-MS provides the tools for direct elucidation of the structure and variety of polar natural compounds in complex matrices. In order to develop efficient and straightforward strategies for the analysis of polar natural products, the potential and the limitations of these hyphenated analytical techniques are discussed using heterocyclic aromatic amines, fumonisins, acylated glycoconjugates and regioisomeric fatty acid hydroperoxides as examples. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

A discharge adaptor interface for use in liquid chromatography/mass spectrometry

A discharge adaptor, composed of a metal casing and platinum (Pt) wire needle, was directly attached to an electrospray ionization (ESI) probe tip, to transform the ionization into atmospheric pressure chemical ionization (APCI). Six generic drugs were analyzed with the developed discharge adaptor (DA) and two commercial interfaces. The DA interface produced more intense radical anions, [M]^.–, and less sodium adduct ions, [M + Na]⁺, than the ESI interface, whereas almost the same molecular ions were detected as the APCI interface. The effects of solvent and desolvation gas flow in the DA interface were similar to those in the ESI interface, but differed from those in the APCI interface. Better sensitivity of the tested drugs was obtained relative to the commercial APCI interface. For human plasma samples, the DA interface also demonstrated good tolerance to plasma matrices, linearity from 5 or 20 to 500 ng/mL (r² > 0.99) and ruggedness. Copyright © 2011 John Wiley & Sons, Ltd.     

LC‐MS analysis of estradiol in human serum and endometrial tissue: Comparison of electrospray ionization,atmospheric pressure chemical ionization and atmospheric pressure photoionization

Accurate measurement of estradiol (E2) is important in clinical diagnostics and research. High sensitivity methods are critical for specimens with E2 concentrations at low picomolar levels, such as serum of men, postmenopausal women and children. Achieving the required assay performance with LC–MS is challenging due to the non‐polar structure and low proton affinity of E2. Previous studies suggest that ionization has a major role for the performance of E2 measurement, but comparisons of different ionization techniques for the analysis of clinical samples are not available. In this study, female serum and endometrium tissue samples were used to compare electrospray ionization (ESI), atmospheric pressure chemical ionization (APCI) and atmospheric pressure photoionization (APPI) in both polarities. APPI was found to have the most potential for E2 analysis, with a quantification limit of 1 fmol on‐column. APCI and ESI could be employed in negative polarity, although being slightly less sensitive than APPI. In the presence of biological background, ESI was found to be highly susceptible to ion suppression, while APCI and APPI were largely unaffected by the sample matrix. Irrespective of the ionization technique, background interferences were observed when using the multiple reaction monitoring transitions commonly employed for E2 (m/z 271 > 159; m/z 255 > 145). These unidentified interferences were most severe in serum samples, varied in intensity between ionization techniques and required efficient chromatographic separation in order to achieve specificity for E2. Copyright © 2013 John Wiley & Sons, Ltd.     

Atmospheric pressure chemical ionization in gas chromatography-mass spectrometry for the analysis of persistent organic pollutants

Atmospheric pressure chemical ionization (APCI) was primarily applied as the ion source for liquid chromatography-mass spectrometry (LC–MS). While APCI started to be used in gas chromatography-mass spectrometry (GC–MS) in 1970s, GC-APCI-MS was not widely used until recently. As a soft ionization technique, APCI provides highly diagnostic molecular ions, which is favored for the wide-scope screening. With the capability of tandem mass spectrometry (MS/MS), GC-APCI-MS methods with high sensitivity and selectivity have been developed and applied in the analysis of persistent organic pollutants (POPs) in environment and biological samples at trace levels. The present review introduces the history of the APCI source, with emphasis on mechanisms of ionization processes under the positive and negative ionization modes. Comparison between GC-APCI-MS and GC–MS with traditional electron ionization (EI) and chemical ionization (CI) are provided and discussed for selectivity, sensitivity and stability for the analyses of POPs. Previous studies found that the GC-APCI-MS methods provided limits of detection (LODs) around 10–100 times lower than other methods. An overview of GC-APCI-MS applications is given with the discussions on the advantages and drawbacks of various analytical methods applied for the analyses of POPs.     

Super‐atmospheric pressure chemical ionization mass spectrometry

Super‐atmospheric pressure chemical ionization (APCI) mass spectrometry was performed using a commercial mass spectrometer by pressurizing the ion source with compressed air up to 7 atm. Similar to typical APCI source, reactant ions in the experiment were generated with corona discharge using a needle electrode. Although a higher needle potential was necessary to initiate the corona discharge, discharge current and detected ion signal were stable at all tested pressures. A Roots booster pump with variable pumping speed was installed between the evacuation port of the mass spectrometer and the original rough pumps to maintain a same pressure in the first pumping stage of the mass spectrometer regardless of ion source pressure. Measurement of gaseous methamphetamine and research department explosive showed an increase in ion intensity with the ion source pressure until an optimum pressure at around 4–5 atm. Beyond 5 atm, the ion intensity decreased with further increase of pressure, likely due to greater ion losses inside the ion transport capillary. For benzene, it was found that besides molecular ion and protonated species, ion due to [M + 2H]⁺ which was not so common in APCI, was also observed with high ion abundance under super‐atmospheric pressure condition. Copyright © 2013 John Wiley & Sons, Ltd.     

Determination of polymer additives by liquid chromatography coupled with mass spectrometry. A comparison of atmospheric pressure photoionization (APPI), atmospheric pressure chemical ionization (APCI), and electrospray ionization (ESI)

A method for the determination of polymer additives like antioxidants, UV absorbers and processing stabilizers using liquid chromatography (LC) coupled with atmospheric pressure photoionization mass spectrometry (APPI-MS) is presented. Ion source parameters were optimized regarding temperatures, gas flow rates, and voltages applied. Detection limits were determined using APPI with or without dopant and were compared with electrospray ionization (ESI) and atmospheric pressure chemical ionization (APCI). Differences between APPI, ESI and APCI are pointed out and the effect of the dopant toluene and acetone is discussed. The optimized method yielded detection limits between 0.001 mg L⁻¹ and 0.022 mg L⁻¹ for 15 different analytes. Linear calibration plots could be obtained for all solutes over a wide concentration range showing satisfying repeatability with standard deviations of peak areas between 3.4% and 7.6%. The results indicate that the developed method can be regarded as suitable for the quantitative determination of polymer additives even at low concentration levels.     

Applications of HPLC-MS in compound Ilex pubescens extract study

In this paper, high performance liquid chromatography (HPLC) along with mass spectrometry (MS) and HPLC along with a diode array detector (DAD) was used to study the compound Ilex pubescens extract. Two ionization techniques: electro spray ionization (ESI) and atmospheric pressure chemical ionization (APCI) were used in this work. The liquid chromatograms obtained by DAD, total ion chromatograms (TIC) from positive-and negative-ion ESI-MS and the positive-and negative-ion APCI-MS were compared. The liquid chromatograms obtained by TIC from ESI-MS provided more information on chromatographic peaks than those obtained by DAD or TIC from APCI-MS. It is suggested that the fingerprints of the compound Ilex pubescens extract should be provided by the liquid chromatograms obtained by DAD together with TIC from the negative-ion ESI-MS. The molecular weights of the nine main components in an HPLC-DAD chromatogram were determined by the corresponding positive-and negative-ion ESI and the positive-and negative-ion APCI mass spectra information. In the liquid chromatogram obtained by TIC from the negative-ion ESI-MS, the molecular weights of 23 main components were determined based on the corresponding positive-and negative-ion ESI mass spectra information.     

Alleviation of ion suppression effect in sonic spray ionization with induced alternating current voltage

In this study, alleviation of ion suppression effect in sonic spray ionization mass spectrometry (SSI‐MS) was investigated. Ion suppression effect was firstly compared between electrospray ionization (ESI) and conventional SSI, and more severe ion suppression effect was observed with SSI. Ion suppression effect of SSI was also found difficult to be alleviated by simply optimizing major parameters. Alternatively, we found that with the assistance of an alternating current (AC) voltage with low amplitude, the ion suppression effect was greatly alleviated (comparable with conventional ESI). That AC voltage was applied outside the SSI spray tip, and no direct contact between the electrode and spray solution was necessary. Besides the alleviation of the ion suppression effect, this newly‐developed method, termed as induced electrosonic spray ionization (IESSI), appeared to preserve similar charge state distribution with SSI for protonated cytochrome c, hemoglobin, and bradykinin. IESSI could also obtain significantly improved ion intensities (~1000‐fold over conventional SSI). In addition, tolerance of concentrated salts for IESSI‐MS was investigated through the analysis of cytochrome c in the presence of concentrated sodium chloride (NaCl) or ammonium acetate (NH₄OAc). Copyright © 2014 John Wiley & Sons, Ltd.     

Sonic spray ionization applied to liquid chromatography/mass spectrometry analysis of endocrine-disrupting chemicals in environmental water samples

A sonic spray ionization liquid chromatography/mass spectrometry (LC/SSI-MS) procedure combined with off-line solid-phase extraction was optimized for the analysis of 20 endocrine-disrupting chemicals (EDCs) in water samples. Method development included a comparison of the novel sonic spray ionization (SSI) with more traditional ion sources, i.e. pneumatically assisted electrospray ionization (ESI) and atmospheric pressure chemical ionization (APCI). It was demonstrated that SSI and ESI spectra were very similar, but were more prone to the formation of solvent cluster ions as compared with APCI spectra. This phenomenon was most prominent for SSI and resulted in an increased chemical background in full-scan mass spectra. However, this chemical noise did not affect the overall sensitivity of SSI and ESI. After optimization of LC and MS parameters, the LC/SSI-MS method was validated. Recoveries ranged from 76.3 up to 113.4% for all compounds. Limits of detection (LOD) and quantitation (LOQ) were established between 3.0 and 11.5 ng/L and 9.9 and 38.0 ng/L, respectively. Within-day (n = 5) and between-day (n = 5) reproducibility were investigated at three levels and ranged from 3.3-16.5% and 7.6-19.2%, respectively. Eight-point calibration curves were established and showed linearity for all compounds (r(2) > 0.987) over a linear dynamic range of 10-10 000 ng/L.     

Potential of atmospheric pressure chemical ionization source in gas chromatography tandem mass spectrometry for the screening of urinary exogenous androgenic anabolic steroids

The atmospheric pressure chemical ionization (APCI) source for gas chromatography-mass spectrometry analysis has been evaluated for the screening of 16 exogenous androgenic anabolic steroids (AAS) in urine. The sample treatment is based on the strategy currently applied in doping control laboratories i.e. enzymatic hydrolysis, liquid–liquid extraction (LLE) and derivatization to form the trimethylsilyl ether-trimethylsilyl enol ether (TMS) derivatives. These TMS derivatives are then analyzed by gas chromatography tandem mass spectrometry using a triple quadrupole instrument (GC-QqQ MS/MS) under selected reaction monitoring (SRM) mode. The APCI promotes soft ionization with very little fragmentation resulting, in most cases, in abundant [M + H]⁺ or [M + H-2TMSOH]⁺ ions, which can be chosen as precursor ions for the SRM transitions, improving in this way the selectivity and sensitivity of the method. Specificity of the transitions is also of great relevance, as the presence of endogenous compounds can affect the measurements when using the most abundant ions. The method has been qualitatively validated by spiking six different urine samples at two concentration levels each. Precision was generally satisfactory with RSD values below 25 and 15% at the low and high concentration level, respectively. Most the limits of detection (LOD) were below 0.5 ng mL⁻¹. Validation results were compared with the commonly used method based on the electron ionization (EI) source. EI analysis was found to be slightly more repeatable whereas lower LODs were found for APCI. In addition, the applicability of the developed method has been tested in samples collected after the administration of 4-chloromethandienone. The highest sensitivity of the APCI method for this compound, allowed to increase the period in which its administration can be detected.     

Thermodynamics of lonization of aqueous lodic acid,an “almost-strong” electrolyte

We have made calorimetric measurements of enthalpies of dilution of aqueous iodic acid and have used these results for evaluation of the standard enthalpy of ionization of HIO₃(aq.). We have also made calorimetric measurements of enthalpies of addition of perchloric acid solution to aqueous solutions of KIO₃, KNO₃, NaIO₃, and NaNO₃ and have used these results to obtain further values for the standard enthalpy of ionization of HIO₃(aq.). On the basis of all these results, we have selected H^o=–660±125 cal-mole^–1 as the best available standard enthalpy of ionization of HIO₃(aq.) at 298.15°K, compared to the previously accepted –2400 cal-mole^–1. Using the best available K=0.157 for ionization, we also obtain G^o=1097 cal-mole^–1 and S^o=–5.9 cal-^oK^–1-mole^–1 for ionization of HIO₃(aq) at 298.15°K.On study leave from Department of Inorganic and Analytical Chemistry, LaTrobe University, Bundoora, Victoria, 3083, Australia, to University of Lethbridge.On study leave from Department of Chemistry, University of Wollongong, Wollongong, N.S.W. 2500, Australia, to University of Lethbridge.