氢在A、X及ZSM-5型沸石上的高压物理吸附

采用常规体积吸附装置测定了77、195、293K和7MPa的条件下氢在A、X及ZSM-5沸石上的吸附特性和吸附容量．所有的氢吸附等温线基本符合Ⅰ型等温线,但在77K,压力为2-5MPa的等温线上观察到了超临界高压吸附所特有的最大吸附量．从等温线确定了等量吸附热并讨论了其影响因素．根据骨架结构和所含阳离子类型的差异,各种沸石表现出不同的氢吸附量．其中NaX沸石在77K/4MPa下的重量储氢分数为2．55％,是该实验中所测得的最高吸附量．CaA、NaX和ZSM-5沸石的氢吸附量与其比表面积成正比,这与沸石中的可用空穴容积有关．然而NaA和KA沸石不存在这种线性关系．实验中还观察到,NaA与KA沸石间出现氢吸附量的临界值是由KA沸石中较大的阳离子堵塞效应引起的．该实验将吸附质分了的动力学直径与沸石主晶孔的有效直径之比用于判断物理吸附中的堵塞效应．     

Pressure dependence of ionic conductivity of hydrated and dehydrated zeolites A

Hydrated and dehydrated zeolites MA (where M=Li, Na and K) with LTA structure have been studied by impedance spectroscopy with scanning frequency from 1 Hz to 1 MHz at high pressure up to 4.5 GPa and high temperature up to 250 °C. Anomalous increase in electrical AC conductivity at about 1.5–2 GPa observed in hydrated zeolites is associated with changes in crystalline structure leading to the formation of high-diffusion state of cation and water stuffing of the channels.

In dehydrated zeolites, electrical conductivity is controlled by diffusion of cations (Li⁺, Na⁺ and K⁺), which is determined by cation sites and aluminosilicate ring windows. LiA and NaA zeolites show normal decrease of conductivity with pressure, whereas KA zeolite exhibits the anomalous dependence with considerable increase and then fast decrease of conductivity. The behaviour of KA zeolite is associated with nearly central location of cation site in 8-membered ring, different from that in LiA and NaA zeolites.     

Adsorption characterization of surfactant-templated ordered mesoporous silicas synthesized with and without hydrothermal treatment

This work reports a systematic study of ordered mesoporous silicas (OMSs) synthesized with and without hydrothermal treatment at 373 K for a series of surfactants of different alkyl chain length (from C10 to C18). For these samples nitrogen adsorption and small angle X-ray scattering (SAXS) data were measured to characterize their adsorption and surface properties. Namely, nitrogen adsorption isotherms were used to evaluate their specific surface area, pore volume and pore size distribution, whereas SAXS data provided information about their structural ordering. It is shown that while the room temperature synthesis afforded OMS samples with cubic MCM-48 structure, an additional 5-day hydrothermal treatment of these samples at 373 K caused their transformation to MCM-41 (two-dimensional hexagonal structure) and improved their pore uniformity, which was manifested by reducing the width of pore size distribution.     

Effects of ultrasonic treatment on zeolite NaA synthesized from by-product silica

The synthesis of zeolite NaA from silica by-product was carried out in the presence of 20 kHz ultrasound at room temperature. Zeolites obtained in this type of synthesis were compared to zeolites obtained by performing conventional static syntheses under similar conditions. The sonication effects on zeolite NaA synthesis were characterized by phase identification, crystallinity etc. The effects of different parameters such as crystallization time and initial materials preparation methods on the crystallinity and morphology of the synthesized zeolites were investigated. The final products were characterized by XRD and FT-IR. It was possible to obtain crystalline zeolite NaA from by-product silica in the presence of ultrasound.     

On the problem of field-gradient NMR measurements of intracrystalline diffusion in small crystallites--water in NaA zeolites as an example

Necessary conditions for measuring intracrystalline diffusion in small crystal size systems via field-gradient NMR are discussed. As an illustrative case self-diffusion coefficients of water adsorbed in NaA zeolites (average crystal diameter about 1 μm) have been measured by ¹H-NMR stimulated echoes in static magnetic field gradients of up to 180 T/m in the temperature range of 254–344 K. Obtaining intracrystalline diffusion coefficients necessitates a sufficiently high spatial resolution only provided by such large field gradients.     

Positron annihilation in synthetic zeolites

Both lifetime and angular correlation of positron annihilation have been measured for a series of synthetic zeolites for which the void structures are known fairly well. All of the zeolites had long lifetime components and a narrow momentum component which are ascribable to o-Ps and p-Ps annihilations in the voids, respectively. The correlation between the width of the p-Ps narrow component and the size of the largest voids showed a remarkable agreement with a theoretical estimate based on the spherical potential well model. The measurement of p-Ps momentum thus appears to be prospective as a tool to determine the size of voids of materials. The lifetime of the long lifetime component, on the other hand, showed a poor correlation with the void size even from a qualitative viewpoint, suggesting that factors other than the simple void size effect are dominant in determining the o-Ps lifetimes. Discussion is made on the cause of the different dependences of o-Ps and p-Ps annihilation parameters on the void size. It has also been found that p-Ps fraction is always larger than one third of the o-Ps fraction in all the zeolites studied. A discussion is presented on this point, too.Formerly, RIISOM     

Analysis of relative pressure range influence on the identification quality during computer identification of adsorption system parameters by employing the new multilayer adsorption models

The aim of this work has been to analyze the problems related to the identification of microporous structure parameters of carbonaceous materials. The new methods for microporous structure parameters identification have been explored with special focus on the influence of the analyzed relative pressure range on the reliability of parameters identification. For that purpose, the adsorption isotherm of nitrogen on active carbon for different ranges of relative pressures p/p₀ was analyzed. The conducted research was to provide for an answer to the question of whether the range of the analyzed relative pressures has any effect on the quality of adsorption system parameters identification, as well as what range of the relative pressure permits execution of the reliable identification of microporous structure parameters.     

高压对以沸石分子筛基质的Eu（Ⅲ）稀土发光材料荧光光谱影响的研究

 本文研究了高压下无机微孔材料的相转变，并讨论了压力对离子交换的Eu（Ⅲ）NaA和Eu（Ⅲ）NaY两种以沸石分子筛为基质的稀土发光材料发光性质的影响。实验结果表明，对于不同基质材料，压力对Eu（Ⅲ）离子的光谱结构的影响，尤其是对⁵D₀→⁷F₁磁偶极跃迁与⁵D₀→⁷F₂电偶极跃迁强度比（I_m/I_e）的影响十分显著。对于Eu（Ⅲ）NaA样品来说，I_m/I_e值随压力的增加而增加，而对于Eu（Ⅲ）NaY样品，I_m/I_e值随压力的增加而减少。     

Novel two-layered zeolite NaA-silicalite-1 membranes

A two-layered zeolite NaA-silicalite-1 membrane has been successfully prepared on a porous α-alumina tube by using seeded hydrothermal synthesis. The procedure involves pre-seeding with nanosized seed and subsequent regrowth by hydrothermal treatment. Single-layered NaA and silicalite-1 membranes were also synthesized for comparison. The membrane was composed of a silicalite-1 layer on top and a NaA layer on the porous support. SEM results of the membrane indicate that both the silicalite-1 layer and the NaA layer are uniform and well-intergrown. The silicalite-1 and NaA layers in the ‘sandwich’ mode have similar thickness of 3-4 μm, whereas the thickness of their respective seed layer is different. The NaA seed layer is much thicker than the silicalite-1seed layer. This may be attributed to the different capillary action on the support and NaA layer during using a slip-casting seeding method. XRD analysis has also proved both zeolite NaA and zeolite silicalite-1 layers coexist in the dual-layered membrane. This method is also suitable for preparing other multi-layer zeolite membranes.     

A novel method for the assembly of nano-zeolite crystals on porous stainless steel microchannel and then zeolite film growth

A new method that is simple, efficient, and clean was developed for seeding surfaces with a monolayer of covalently bonded zeolite seeds. This method was used to seed the microchannels fabricated on porous stainless steel with NaA nano-zeolites enabling the deposition and growth of defect-free zeolite film. The NaA nano-zeolites were attached to the surface of the stainless steel via alkoxysilane linkers (e.g., 3-chloropropyltrimethoxysilane and 3-aminopropyltrimethoxysilane) grafted on the stainless steel. The NaA zeolite grown on the microchannel by hydrothermal synthesis consists of intergrown, (1 1 1)-oriented pyramidal NaA crystals that completely clad the stainless steel grains. The zeolite cladding the grains grew uniformly until the zeolite layers of neighboring grain impinges, then intergrew to fully bridge the gaps between the grains forming a defect-free film layer. A separation factor of 10,000 and a flux of 0.04 kg m⁻² h⁻¹ were obtained for water pervaporation from a 3 wt% water-benzaldehyde solution at room temperature.     

Equilibrated thermodesorption studies of adsorption of n-hexane and n-heptane on zeolites Y, ZSM-5 and ZSM-11

Gravimetric measurements of thermodesorption of n-hexane and n-heptane were performed under quasi-equilibrium conditions. Differential thermodesorption profiles for ZSM-5 and ZSM-11 showed two peaks, but for Y zeolites, only one thermodesorption peak was observed. A model function, derived from the Langmiur adsorption model, was fitted to the experimental data, and the model parameters (the adsorption entropy and enthalpy) were estimated. The two-step desorption profiles observed for ZSM-5 and ZSM-11 were attributed to the commensurate freezing effect, i.e. a transition in the adsorbed phase resulting in ordering of the adsorbed molecules in the zeolite channels. The results observed for ZSM-11 indicate that the zigzag channels typical for ZSM-5 micropore system are not necessary for this transition to occur.     

Preparation and hydrogen storage of activated rayon-based carbon fibers with high specific surface area

Activated carbon fibers were prepared from rayon-based carbon fibers by two step activations with steam and KOH treatments. Hydrogen storage properties of the activated rayon-based carbon fibers with high specific surface area and micropore volume have been investigated. SEM, XRD and Brunauer-Emmett-Teller (BET) were used to characterize the samples. The adsorption performance and porous structure were investigated by nitrogen adsorption isotherm at 77 K on the base of BET and density functional theory (DFT). The BET specific surface area and micropore volume of the activated rayon-based carbon fibers were 3144 m²/g and 0.744 m³/g, respectively. Hydrogen storage properties of the samples were measured at 77 and 298 K with pressure-composition isotherm (PCT) measuring system based on the volumetric method. The capacities of hydrogen storage of the activated rayon-based carbon fibers were 7.01 and 1.46 wt% at 77 and 298 K at 4 MPa, respectively. Possible mechanisms for hydrogen storage in the activated rayon-based carbon fibers are discussed.     

Synthesis and properties of new nitrogen-doped nanostructured carbon materials obtained by templating of mesoporous silicas with aminosugars

The negative templating synthesis process has been applied to prepare nanostructured carbon materials with a high nitrogen content. SBA-15 silica template was impregnated with the following carbon precursors: sucrose, glucose and amino-glucose. The structure of the materials was investigated by SAXS, WAXS and TEM. Nitrogen functions were analyzed by XPS and the textural parameters of the carbons were studied by nitrogen and CO₂ adsorption. X-ray and TEM studies confirmed that a pore nanostructure is inherited from the silica templates. XPS analysis showed that the nitrogen content of the materials can be controlled between 2 and 5 wt% and that N atoms are strongly bonded in the carbon structure in heterocycles or nitrile functions. An important result is that these nanostructured carbon materials exhibits interesting textural properties with BET surface areas ranging between 1000 and . Moreover, the study of the influence of nitrogen on the textural and structural parameters of the resulting carbon materials shows that nitrogen plays an active role during the synthesis process. This observation is also supported by the speciation of nitrogen in the nanostructured carbon materials.     

Prediction of adsorption of xenon in zeolite NaA with molecular density functional theory

The Tarazona model of molecular density functional theory is used to determine the adsorption isotherm and the density distribution of xenon atoms in zeolite NaA. We consider the alpha cage of NaA to be fully three-dimensional and we introduce a basis set for the density distribution to make the solution computationally tractable. The results of this density functional theory model are compared to previous results of grand canonical Monte Carlo simulations for the same system.We dedicate this paper to Professor Herbert Wagner, whose excellent contributions to density functional theory typify his valuable role in the advancement of statistical physics     

Characterization and adsorptive application of ordered mesoporous silicas

The adsorption behaviour of the n-octane/ethanol binary liquid mixture has been studied on ordered mesoporous silica materials. Adsorption excesses on SBA-15, SBA-16 and MCM-48 solids are measured and described by mathematical functions. The experimental adsorption excess isotherms are presented and discussed. The mesoporous silicas used for liquid-adsorption experiments are characterized by nitrogen adsorption before and after liquid adsorption by the powder X-ray diffraction (XRD) and by the sample controlled thermal analysis (SCTA).     

Combined SANS and SAXS study of the action of ultrasound on the structure of amorphous zirconia gels

In the present work, we have studied for the first time the combined effect of both sonication and precipitation pH on the structure of amorphous zirconia gels synthesized from zirconium(IV) propoxide. The techniques of small-angle neutron and X-ray scattering (SANS and SAXS) and low temperature nitrogen adsorption provided the integral data on the changes in the microstructure and mesostructure of these materials caused by ultrasonic (US) treatment. Amorphous ZrO₂·xH₂O synthesized under ultrasonic treatment was found to possess a very structured surface, characterized by the surface fractal dimension 2.9–3.0, compared to 2.3–2.5 for the non US-assisted synthesis, and it was also found to possess a higher specific surface area, while the sizes of the primary particles remain unchanged.     

Characterization of nanoporous carbons by combining CO2 and H2 sorption data with the Monte Carlo simulations

The Monte Carlo method in its grand ensemble variant (GCMC) is used in combination with experimental data in order to characterize microporous carbons and obtain the optimal pore size distribution (PSD). In particular, the method is applied in the case of AX-21 carbon. Adsorption isotherms of CO₂ (253 and 298 K) and H₂ (77 K) up to 20 bar have been measured, while the computed isotherms resulted from the GCMC simulations for several pore widths up to 3.0 nm. For the case of H₂ at 77 K quantum corrections were introduced with the application of the Feynman-Hibbs (FH) effective potential. The adsorption isotherms were used either individually or in a combined manner in order to deduce PSDs and their reliability was examined by the ability to predict the experimental adsorption isotherms. The combined approach was found to be capable of reproducing more accurately all the available experimental isotherms.     

小角x射线散射方法研究甲基改性氧化硅干凝胶的孔结构

以正硅酸乙酯［Si(OC2H5)4，TEOS］为前驱体制备SiO2悬浮液，分别以甲基三乙氧基硅烷［CH3Si(OC2H5)3，MTES］和二甲基二乙氧基硅烷［(CH3)2Si(OC2H5)2，DDS］为前驱体制备硅氧烷聚合物溶液，通过混合法得到两种不同的甲基改性氧化硅凝胶-测量了凝胶的散射强度，计算了凝胶的孔径分布、平均孔径DSAXS、界面层厚度E等参数，结合氮气吸附实验，分析了凝胶的孔结构-发现SiO2一次簇团被MTES聚合物或DDS聚合物连接为二次簇团时产生微孔，同时甲基随聚合物连接于凝胶骨架上形成与 关键词： 小角x射线散射 甲基改性氧化硅 干凝胶 孔结构     

Comparative studies of p6m siliceous mesostructures by powder X-ray diffraction and nitrogen adsorption

Two-dimensional mesostructures with p6m symmetry such as MCM-41 and SBA-15 are the subject of intensive studies by using nitrogen and argon adsorption, transmission electron microscopy, and powder X-ray diffraction/scattering techniques. The latter may involve the X-ray diffraction (XRD) or small angle X-ray scattering (SAXS) measurements. The XRD/SAXS patterns for the aforementioned ordered mesostructures often exhibit four or more reflections, the most intensive one, 1 0 0 peak, and three less intensive peaks, 1 1 0, 2 0 0, 2 1 0. So far, analysis of these patterns was usually limited for the evaluation of the unit cell parameter and the identification of the observed peaks. In this work we present an attempt to analyze the XRD/SAXS patterns by including not only the position of observed peaks but also their intensity. It is shown that the intensity of these peaks, especially 1 1 0 peak, depends on the ratio of the pore diameter to the unit cell parameter. In particular, this dependence was studied for the intensity ratio of 1 1 0 and 2 0 0 peaks assuming 2 0 0 peak as a reference reflection because of its nearness to 1 1 0 peak (which minimizes the influence of other factors than the structural ones on the 1 1 0/2 0 0 intensity ratio analysis) and similar intensity to that of 1 1 0 peak. The values of the 1 1 0/2 0 0 intensity ratio were determined for many MCM-41 and SBA-15 samples and analyzed in relation to the pore width/unit cell ratio, where the pore width was estimated on the basis of nitrogen adsorption data or by the XRD/SAXS structure modeling. Comparative analysis of this intensity ratio for numerous MCM-41 and SBA-15 samples allows for a quick estimation of the pore width and provides some information about hexagonality of mesopores in these materials.