Electrical conduction and magnetoelectric effect of (x) BaTiO3 + (1−x) Ni0.92Co0.03Cu0.05Fe2O4 composites in ferroelectric rich region

Particulate composites with composition (x)BaTiO₃+(1−x)Ni_0.92Co_0.03Cu_0.05Fe₂O₄ in which x varies as 1, 0.85, 0.70, 0.55 and 0 (in mol%) were prepared by the conventional double sintering ceramic technique. The presence of two phases viz. ferromagnetic (Ni_0.92Co_0.03Cu_0.05Fe₂O₄) and ferroelectric (BaTiO₃) was confirmed by X-ray diffraction analysis. The dc resistivity and thermo-emf measurements were carried out with variation of temperature. The ac conductivity (σ_ac) measurements investigated in the frequency range 100 Hz to 1 MHz conclude that the conduction in these composites is due to small polarons. The variation of dielectric constant and loss tangent with frequency (20 Hz to 1 MHz) was studied. The static magnetoelectric conversion factor, i.e. dc (dE/dH)_H was measured as a function of intensity of applied magnetic field. The changes were observed in electrical properties as well as in magnetoelectric voltage coefficient as the molar ratio of the constituent phases was varied. A maximum value of magnetoelectric conversion factor of 536.06 μV/cm Oe was observed for the composite with 70% BaTiO₃+30% Ni_0.92Co_0.03Cu_0.05Fe₂O₄ at a dc magnetic field of 2.3 K Oe. The maximum magnetoelectric conversion output has been explained in terms of ferrite-ferroelectric content, applied static magnetic field and resistivity.     

Magnetic and dielectric properties of Ni0.8Co0.1Cu0.1Fe2O4+PZT composites

Magnetoelectric composites of Ni_0.8Co_0.1Cu_0.1Fe₂O₄ and Lead Zirconate Titanate (PZT) were prepared by using conventional ceramic method. The measured values of saturation magnetization (M_s) and magnetic moments (μ_B) are in accordance with the volume fraction of ferrite content in the composite. The dielectric constant of the composites decreases with frequency. The plots of dielectric constant () against temperature (T) show a peak at their respective transition temperatures. The ME output was measured by varying dc bias magnetic field. A large ME output signal of 776 mV/cm was observed for 35% ferrite +65% ferroelectric composite. The magnetoelectric (ME) response is found to be dependent on the content of ferrite phase.     

Phase transformation behavior and dielectric characteristics of BaTi1−x(Al1/2Nb1/2)xO3 (0.01≤x≤0.40) ceramics

Microstructure, phase transformation behavior and dielectric properties of BaTi_1−x(Al_1/2Nb_1/2)_xO₃ (0.01≤x≤0.40) ceramics were investigated. A high level of (Al_1/2Nb_1/2)⁴⁺ substitution for Ti⁴⁺ ions was not conducive to the stability of the perovskite structure and resulted in the formation of BaAl₂O₄. As x was increased, lattice constants and unit cell volume decreased, reached a minimum at x=0.10 and then increased. The BaTi_1−x(Al_1/2Nb_1/2)_xO₃ ceramics at room temperature experienced a transformation from ferroelectric to paraelectric phase with increasing (Al_1/2Nb_1/2)⁴⁺ concentration. Meanwhile, permittivity of the BaTi_1−x(Al_1/2Nb_1/2)_xO₃ ceramics was markedly reduced, while Q value was slightly increased. Frequency dispersion of dielectric peak was obviously increased as x was increased from 0.01 to 0.10. It is of great interest that a dielectric abnormity represented by a broad dielectric peak at 200-400 K was observed for the composition with x=0.40.     

The influence of microscopic parameters on the ionic conductivity of SrBi2(Nb1−xVx)2O9−δ(0≤x≤0.3) ceramics

Layered SrBi₂(Nb_1−xV_x)₂O_9−δ (SBVN) ceramics with x lying in the range 0-0.3 (30 mol%) were fabricated by the conventional sintering technique. The microstructural studies confirmed the truncating effect of V₂O₅ on the abnormal platy growth of SBN grains. The electrical conductivity studies were centred in the 573-823 K as the Curie temperature lies in this range. The concentration of mobile charge carriers (n), the diffusion constant (D₀) and the mean free path (a) were calculated by using Rice and Roth formalism. The conductivity parameters such as ion-hopping rate (ω_p) and the charge carrier concentration (K′) term have been calculated using Almond and West formalism. The aforementioned microscopic parameters were found to be V₂O₅ content dependent on SrBi₂(Nb_1−xV_x)₂O_9−δ ceramics.     

Dielectric and modulus behavior of LiFe1/2Ni1/2VO4 ceramics

The polycrystalline sample of LiFe_1/2Ni_1/2VO₄ was prepared by a standard solid-state reaction technique and confirmed by X-ray diffractometry. LiFe_1/2Ni_1/2VO₄ has orthorhombic crystal structure whose dielectric and electric modulus properties were studied over a wide frequency range (100 Hz–1 MHz) at different temperatures (296–623 K) using a complex impedance spectroscopy (CIS) technique. The frequency and temperature dependence of dielectric constant (ε_r) and tangent loss (tan δ) of LiFe_1/2Ni_1/2VO₄ are studied. The variation of ε_r as a function frequency at different temperatures exhibits a dispersive behavior at low frequencies. The variation of the ε_r as a function of temperature at different frequencies shows the dielectric anomaly in ε_r at 498 K with maximum value of dielectric constant 274.49 and 96.86 at 100 kHz and 1 MHz, respectively. Modulus analysis was carried out to understand the mechanism of the electrical transport process, which indicates the non-exponential type of conductivity relaxation in the material. The activation energy calculated from electric modulus spectra is 0.38 eV.     

Physical properties of BaMg1/3Nb2/3O3-BaCo1/3Nb2/3O3 solid solutions

Structural, electric and magnetic properties of Ba₃Mg_1−xCo_xNb₂O₉ based dielectric ceramic compounds have been studied. The samples, prepared by a solid state reaction method, were characterised by X-ray powder diffraction (XRPD), electron microscopy (SEM), dielectric (ε(T)) and magnetic measurements (χ⁻¹(T)). The XRPD analyses showed that the crystal structure of these compounds does change by the increase of substitution degree, passing from a superstructure hexagonal-type, (no. 164), space group (SG) to a simple structure cubic-type, (no. 221), SG. However, the evolution of the elementary unit cell lattice parameter can be followed and it exhibit a linear increasing tendency with increase in the substitution, indicating the existence of a solid solution through out the investigated range of substitution (0-1). The microstructure analysis shows a variation in the grain size and also the porosity of the samples with the degree of substitution. The results are in good agreement with that of dielectric measurements, which also showed that the dielectric constant (ε) increases with the increase of cobalt content. The magnetic characterization of cobalt substituted samples showed an antiferromagnetic type super-exchange interaction between these magnetic ions. At the same time, the values of effective magnetic momentum (μ_eff) are close to the value that corresponds to Co²⁺ free ions. The study highlights the possibility of modelling these materials by substitutions, in order to improve properties of negative-positive-zero (NPO) type dielectric applications.     

Electrical properties of SrBi2(Nb0.5Ta0.5)2O9 ceramics

Aurivillius SrBi₂(Nb_0.5Ta_0.5)₂O₉ (SBNT 50/50) ceramics were prepared using the conventional solid-state reaction method. Scanning electron microscopy was applied to investigate the grain structure. The XRD studies revealed an orthorhombic structure in the SBNT 50/50 with lattice parameters a=5.522 Å, b=5.511 Å and c=25.114 Å. The dielectric properties were determined by impedance spectroscopy measurements. A strong low frequency dielectric dispersion was found to exist in this material. Its occurrence was ascribed to the presence of ionized space charge carriers such as oxygen vacancies. The dielectric relaxation was defined on the basis of an equivalent circuit. The temperature dependence of various electrical properties was determined and discussed. The thermal activation energy for the grain electric conductivity was lower in the high temperature region (T>303.6 °C, E_a−ht=0.47 eV) and higher in the low temperature region (T<303.6 °C, E_a−lt=1.18 eV).     

Hydrothermal synthesis and structural characterization of (1−x)α-Fe2O3-xSnO2 nanoparticles

Structural and morphological characteristics of (1−x)α-Fe₂O₃-xSnO₂ (x=0.0-1.0) nanoparticles obtained under hydrothermal conditions have been investigated by X-ray diffraction (XRD), transmission Mössbauer spectroscopy, scanning and transmission electron microscopy as well as energy dispersive X-ray analysis. On the basis of the Rietveld structure refinements of the XRD spectra at low tin concentrations, it was found that Sn⁴⁺ ions partially substitute for Fe³⁺ at the octahedral sites and also occupy the interstitial octahedral sites which are vacant in α-Fe₂O₃ corundum structure. A phase separation of α-Fe₂O₃ and SnO₂ was observed for x≥0.4: the α-Fe₂O₃ structure containing tin decreases simultaneously with the increase of the SnO₂ phase containing substitutional iron ions. The mean particle dimension decreases from 70 to 6 nm, as the molar fraction x increases up to x=1.0. The estimated solubility limits in the nanoparticle system (1−x)α-Fe₂O₃-xSnO₂ synthesized under hydrothermal conditions are: x≤0.2 for Sn⁴⁺ in α-Fe₂O₃ and x≥0.7 for Fe³⁺ in SnO₂.     

Dielectric properties and magnetoelectric effect of (x)NiFe2O4+(1−x)Ba0.8Sr0.2TiO3 composites

Magnetoelectric composites of NiFe₂O₄ and Ba_0.8Sr_0.2TiO₃ were prepared using conventional double-sintering ceramic method. The phase formation of magnetoelectric composites was confirmed by XRD technique. Variation of dielectric constant and loss tangent at room temperature with frequency in the range 100 Hz-1 MHz has been studied. Also the variation of dielectric constant and loss tangent with temperature and composition at fixed frequencies of 1 kHz, 10 kHz, 100 kHz and 1 MHz is reported. The static value of the magnetoelectric conversion factor was measured as a function of intensity of the magnetic field. The ME voltage coefficient of about 430 μV/cm Oe was observed for 15% NiFe₂O₄+85% Ba_0.8Sr_0.2TiO₃ composite. All the samples show linear variation of magnetoelectric conversion in the presence of static magnetic field.     

Electronic transport and magnetic studies of La1−xCax−0.08Sr0.04Ba0.04MnO3

Lanthanum based mixed valence manganite system La_1−xCa_x−0.08Sr_0.04Ba_0.04MnO₃ (LCSBMO; x=0.15, 0.24 and 0.33) synthesized through the sol-gel route is systematically investigated in this paper. The electronic transport and magnetic susceptibility properties are analyzed and compared, apart from the study of unit cell structure, microstructure and composition. Second order phase transition is observed in all the samples and significant difference is observed between the insulator to metal transition temperature (T_MI) and paramagnetic (PM) to ferromagnetic (FM) transition temperature (T_C). In contrast to the insulating FM behaviour usually observed in La_1−xCa_xMnO₃ (LCMO) for x=0.15, a clear insulator to metal transition is observed for LCSBMO for the same percentage of lanthanum. The temperature dependent resistivity of polycrystalline pellets, when obeying the well studied law ρ=ρ_o+ρ₂T² for T<T_MI, is observed to differ significantly in the values of ρ_o and ρ₂, with the electrical conductivity increasing with x. The variable range hopping model has been found to fit resistivity data better than the small polaron model for T>T_MI. AC magnetic susceptibility study of the polycrystalline powders of the manganite system shows the highest PM to FM transition of 285 K for x=0.33.     

Structural, optical and dielectric studies of NixZn1−xFe2O4 prepared by auto combustion route

Ni_xZn_1−xFe₂O₄ (0≤x≤1) powders were synthesised by the auto combustion method. The derived samples show well defined peaks of cubic spinal structure with space group Fd3m. The lattice parameter calculated increased from 0.8372 nm to 0.8429 nm with raise of Zn content. The average crystallite sizes were determined by using Debye-Scherer method and found to be in the range of 18-23 nm. Microstructural analyses show the regular and uniform grain morphology. Raman analyses demonstrated that the peaks have symmetric and asymmetric stretching as well as symmetric bending. Fourier transform infrared spectroscopy was used to investigate the structure and shows the changes in the tetrahedral and octahedral bond stretching. Photoluminescence measurements indicated intense emission in the wavelength range lie in blue-green region. The composition with x=0.2 showed highest intensity and explained on the basis of disordered cluster model. Dielectric analyses showed frequency sensitive behaviour in the low frequency region and frequency independent characteristics at high frequency side. The composition with x=0.2 showed highest dielectric constant and lowest dielectric loss in the studied frequency range. The ac conductivity showed a power law behaviour and conduction is explained on the basis of hoping mechanism.     

Low temperature synthesis of Mn0.4Zn0.6In0.5Fe1.5O4 nanoferrite for high-frequency applications

In the present study, nanoferrite of composition Mn_0.4Zn_0.6In_0.5Fe_1.5O₄ has been synthesized by co-precipitation method. Decomposition of residue at a temperature as low as 200 °C gives the ferrite powder. The ferrite has been, finally, sintered at 500 °C. The structural studies have been made by using X-ray diffraction (XRD) technique and scanning electron microscopy (SEM), which confirm the formation of single spinel phase and nanostructure. The dc resistivity is studied as a function of temperature and values found are more than twice those for the samples prepared by the other chemical methods. It is found that the resistivity decreases with increase in temperature. The initial permeability value is found to be higher as compared to the other chemical routes. The initial permeability value is found to increase with increase in temperature. At a certain temperature called Curie temperature, it attains a maximum value, after which the initial permeability decreases sharply. Even at nanolevel, appreciable value of initial permeability is obtained and low magnetic losses make these ferrites especially suitable for high-frequency applications. The particle size is calculated using Scherrer's equation for Lorentzian peak, which comes out between 35 and 49 nm. Possible mechanisms contributing to these processes have been discussed.     

Electrical and electrochemical properties of molten salt-synthesized Li4Ti5−xSnxO12 (x=0.0, 0.05 and 0.1) as anodes for Li-ion batteries

Submicron-sized polyhedral Li₄Ti_5−xSn_xO₁₂ (x=0.0, 0.05, and 0.1) materials were successfully prepared by a single-step molten salt method. The structural, morphological, transport and electrochemical properties of the Li₄Ti_5−xSn_xO₁₂ were studied. X-ray diffraction patterns showed the formation of a cubic structure with a lattice constant of 8.31 Å, and the addition of dopants follows Vegard's law. Furthermore, FT-IR spectra revealed symmetric stretching vibrations of octahedral groups of MO₆ lattice in Li₄Ti₅O₁₂. The formation of polyhedral submicron Li₄Ti_5−xSn_xO₁₂ particles was inferred from FE-SEM images, and a particle size reduction was observed for Sn-doped Li₄Ti₅O₁₂. The chemical composition of Ti, O and Sn was verified by EDAX. The DC electrical conductivity was found to increase with increasing temperature, and a maximum conductivity of 8.96×10⁻⁶ S cm⁻¹ was observed at 200 °C for Li₄Ti₅O₁₂. The galvanostatic charge–discharge behavior indicates that the Sn-doped Li₄Ti₅O₁₂ could be used as an anode for Li-ion batteries due to its enhanced electrochemical properties.     

Magnetic properties of xNi0.53Cu0.12Zn0.35Fe1.88O4+(1−x)BaTiO3 nanocomposites

The nanocrystalline Ni_0.53Cu_0.12Zn_0.35Fe_1.88O₄ and BaTiO₃ powders were prepared using Microwave-Hydrothermal (M-H) method at 160 °C/45 min. The as synthesized powders were characterized using the X-ray diffraction (XRD) and Transmission Electron Microscope (TEM). The size of the powders that were synthesized using M-H system was found to be ∼30 and ∼50 nm for ferrite phase and ferroelectric phases, respectively. The powders were densified using microwave sintering method at 900 °C/30 min. The ferrite and ferroelectric phases were observed from XRD and morphology of the composites was observed with the Scanning Electron Microscope (SEM).The magnetic hysteresis loops were recorded using the Vibrating Sample Magnetometer (VSM).The frequency dependence of real (μ′) and imaginary (μ″) parts of permeability was measured in the range of 1 MHz-1.8 GHz. The permeability decreases with an increase of BaTiO₃ content at 1 MHz. The transition temperature (T_C) of ferrite was found to be 245 °C. The T_C of composite materials decreases with an increase in BaTiO₃ content.     

Synthesis and characterization of the xZnO-(1−x)α-Fe2O3 nanoparticles system

The xZnO-(1−x)α-Fe₂O₃ nanoparticles system has been obtained by mechanochemical activation for x=0.1, 0.3 and 0.5 and for ball milling times ranging from 2 to 24 h. Structural and morphological characteristics of the zinc-doped hematite system were investigated by X-ray diffraction (XRD) and Mössbauer spectroscopy. The Rietveld structure of the XRD spectra yielded the dependence of the particle size and lattice constant on the amount x of Zn substitutions and as function of the ball milling time. The x=0.1 XRD spectra are consistent with line broadening as Zn substitutes Fe in the hematite structure and the appearance of the zinc ferrite phase at milling times longer than 4 h. Similar results were obtained for x=0.3, while for x=0.5 the zinc ferrite phase occurred at 2 h and entirely dominated the spectrum at 24 h milling time. The Mössbauer spectra corresponding to x=0.1 exhibit line broadening as the ball milling time increases, in agreement with the model of local atomic environment. Because of this reason, the Mössbauer spectrum for 12 h of milling had to be fitted with two sextets. For x=0.3 and 12 milling hours, the Mössbauer spectrum reveals the occurrence of a quadrupole-split doublet, with the hyperfine parameters characteristic to zinc ferrite, ZnFe₂O₄. This doublet clearly dominates the Mössbauer spectrum for x=0.5 and 24 h of milling, demonstrating that the entire system of nanoparticles consists finally of zinc ferrite. As ZnO is not soluble in hematite in the bulk form, the present study clearly demonstrates that the solubility limits of an immiscible system can be extended beyond the limits in the solid state by mechanochemical activation. Moreover, this synthesis route allowed us to reach nanometric particle dimensions, which would make the materials very important for gas sensing applications.     

Selected properties of EuCo2(Si1−xGex)2 alloys

EuCo₂(Si_1−xGe_x)₂, x=0, 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8, 0.9, 1 samples were synthesised by induction melting followed by annealing at 900 °C and rapid quenching. X-ray powder diffraction and Auger electron spectroscopy studies revealed that solid solutions are formed only for x?0.2 and x?0.7. Magnetic susceptibility investigations for the solid solutions revealed a dominant divalent europium valence state in the germanium-rich samples and a dominant trivalent europium component in the silicon-rich samples. In the germanium-rich samples, a long-range antiferromagnetic ordering was observed. In all samples studied, additional magnetic transitions at various temperatures were detected, which could be attributed to small clusters containing different europium chemical surrounding from that in the predominant phase.     

Microwave dielectric properties of high quality factor La(Mg0.5−xCaxSn0.5)O3 ceramics

The microwave dielectric properties of La(Mg_0.5−xCa_xSn_0.5)O₃ ceramics were examined with a view to their exploitation for wireless communications. The La(Mg_0.5−xCa_xSn_0.5)O₃ ceramics were prepared by the conventional solid-state method with various sintering temperatures. The La(Mg_0.5−xCa_xSn_0.5)O₃ ceramics contained Ca₂SnO_4, CaSnO₃, and La₂O₃. The amount of Ca₂SnO₄ increased with increasing sintering temperature. However, the relative amount of CaSnO₃ decreased with increasing sintering temperature. An apparent density of 6.52 g/cm³, a dielectric constant (ε_r) of 20.2, a quality factor (Q×f) of 80,500 GHz, and a temperature coefficient of resonant frequency (τ_f) of −79 ppm/°C were obtained for La(Mg_0.4Ca_0.1Sn_0.5)O₃ ceramics that were sintered at 1500 °C for 4 h.     

Local order and structural transitions in the molecule-based layer ferrimagnet (n-C4H9)4N FeFe(C2O4)3

Local structural order and temperature-dependent structural variation have been studied in the molecular-based layer ferrimagnet (n-C₄H₉)₄N Fe^IIFe^III(C₂O₄)₃ by EXAFS and high resolution X-ray powder diffraction. The EXAFS spectra measured at the Fe K-edge are successfully modelled by successive O, C, O and metal shells, showing that even when there is extensive structural disorder due to stacking faults, the local structural order in this class of ferrimagnets is fully retained. In this salt, which shows remarkable negative magnetisation at low temperature (Néel class Q), the EXAFS Debye-Waller factor has a discontinuity at 40 K, corresponding to one found in the magnetisation. At the same temperature there is also a change in the expansion of the lattice as evidenced by the high resolution X-ray powder diffraction.     

Dielectric and piezoelectric properties of barium-modified Aurivillius-type Na0.5Bi4.5Ti4O15

In this study, monophasic Ba_x(Na_0.5Bi_0.5)_1−xBi₄Ti₄O₁₅ (x=0.03, 0.06, 0.09 and 0.12) ceramics fabricated from the powders synthesized via the solid-state reaction route exhibited relaxor behavior. X-ray diffraction analysis revealed that the barium-modified Na_0.5Bi_4.5Ti₄O₁₅ ceramics have a pure four-layer Aurivillius phase structure. Dielectric properties and phase transitions were studied and are explained in terms of lattice response of these ceramics. A shift in ferroelectric–paraelectric phase transition (T_c) to lower temperatures and a corresponding increase in permittivity peak with increasing concentration of Ba²⁺ are also observed. The decrease of orthorhombicity in the lattice structure by the larger Ba²⁺ ion incorporation, indicating an approach of a and b parameters, results in lower Curie temperature. The piezoelectric activity of Na_0.5Bi_4.5Ti₄O₁₅ (NBT) ceramics was significantly improved by the modification of barium. The Curie temperature T_c and piezoelectric coefficient d₃₃ for the composition with x=0.12 were found to be 635 °C and 21 pC/N, respectively. The relationship of polarization with lattice response is discussed.     

Structural and electrical behavior of Pb(Mg1/4Cd1/4Mo1/2)O3 ceramics

Preliminary X-ray structural analysis of polycrystalline Pb(Mg_1/4Cd_1/4Mo_1/2)O₃ ceramics, prepared by a solid-state reaction technique, provides single-phase orthorhombic structure at room temperature. Detailed dielectric studies of the material as a function of temperature reveal a sharp phase transition at temperature T_c=49°C obeying Curie-Weiss behavior. Scanning electron microscope (SEM) studies of the sample show the uniform distribution of grains in the samples. A dielectric anomaly and ferroelectric phase transition observed at 49°C was supported by polarization studies. The activation energy of the sample was calculated from the dielectric data. The variation of dc resistivity with temperature suggests that the compound behaves as a negative temperature coefficient resistor (NTCR).