Sc2O3-W matrix impregnated cathode with spherical grains

Sc₂O₃-W matrix cathodes have been prepared by using a liquid-liquid doping method combined with high-temperature sintering. The microstructure and physical behavior of active substances of scandia-doped tungsten matrix and impregnated cathode has been studied by SEM and AES methods. The results show that the matrix has a homogeneous structure composed of W grains with spherical shape and superfine Sc₂O₃ particles dispersed uniformly over and among W grains. After impregnation, this Sc-type impregnated cathode has high emission capability. Space-charge-limited current density could reach 52 A/cm² at 850 °C_b. The high emission results from a Ba-Sc-O active layer with a thickness of about 80 nm, which is formed at the cathode surface during the activation period. Both the decrease of the thickness of active surface layer and the decrease of the content of Sc at the surface could lead to the degradation of current density during operation.     

Characterization of scandia doped pressed cathode fabricated by spray drying method

Scandia doped pressed cathode was prepared by a new method of spray drying combined with two-step hydrogen reduction process. The Sc₂O₃ and barium-calcium aluminate co-doped powders have sub-micrometer size in the range of 0.1-1 μm and scandium oxide and barium-calcium aluminate are distributed evenly in the powders. The cathodes sintered by powder metallurgy at 1600 °C_b have a smooth surface and sub-micrometer grain structure with homogeneous distribution of scandium, barium, calcium and aluminum which are dispersed over and among the tungsten grains. This cathode has good emission, e.g., the current density of this cathode reaches 31.50 A/cm² at 850 °C_b. After proper activation, the cathode surface is covered by a Ba-Sc-O active substances layer with a preferable atomic ratio, leading to its good emission property. The evaporation activation energy of SDP cathode with 4.58 eV is the highest among the Ba-W, M-type and SDP cathodes, and the average evaporation velocity v_t of SDP cathode with 1.28 × 10⁻⁸ g cm⁻² s⁻¹ at 1150 °C_b is the lowest one.     

Effects of precursor types of Fe and Ni components on the properties of NiFe2O4 powders prepared by spray pyrolysis

The effects of the precursor types of Ni and Fe components on the morphology, mean size, and magnetic property of NiFe₂O₄ powders prepared by spray pyrolysis from the spray solution, with citric acid were studied. The precursor powders with hollow and thin wall structure turned to the nano-sized NiFe₂O₄ powders after post-treatment at a temperature of 800 °C. The nickel ferrite powders obtained from the spray solution with ferric chloride had nanometer sizes and narrow size distributions irrespective of the types of nickel precursor. The nickel ferrite powders obtained from the spray solution with ferric nitrate and nickel chloride also had nanometer size and narrow size distribution. The saturation magnetizations of the NiFe₂O₄ powders changed from 37 to 42 emu/g according to the types of the Fe and Ni precursors. The saturation magnetizations of the NiFe₂O₄ powders increased with increasing the Brunauer-Emmett-Teller (BET) surface areas of the powders.     

Studies on the structural and electrical properties of spray deposited SnO2:Sb thin films as a function of substrate temperature

Thin films of antimony doped tin oxide (SnO₂:Sb) were prepared by spray pyrolysis technique using SnCl₂ as precursor with the various antimony doping levels ranging from 1 to 4 wt%. The XRD analysis showed that the undoped SnO₂ films grow in (211) preferred orientation whereas the Sb doped films grow in (200) plane. Scanning electron microscopy studies indicated that the surface of the films prepared with lower doping level (1 wt%) consists of larger grains whereas those prepared with higher doping levels (>1 wt%) consist of smaller grains. The sheet resistance has been found to be reduced considerably (2.17 Ω/□) for Sb doped films. To the best of our knowledge this is the lowest sheet resistance obtained for Sb doped SnO₂ thin films.     

Properties and manufacture of top-layer scandate cathodes

The life and/or the staying power against ion bombardment of scandate cathodes can be improved by using a top layer of W + Sc₂O₃ or W + W/ScH₂ on a tungsten matrix. The latter is impregnated with the usual 4-1-1 impregnant. Even at high voltage pulses the current densities are so high that the deviation from space charge limitation is small. The manufacture is discussed and the cathode life at the operating temperature of 1220 K is shown to be very long. Moreover, the relationship between processing parameters and emission recovery after ion bombardment is examined with the aid of combined sputter- and scanning-Auger measurements. It is shown that thin-layer coverage of tungsten by scandia is important to the high emission. This coverage is related to the impregnation process. After extended sputtering it cannot be completely recovered by reactivation. Consequently, the top layer cathodes cannot withstand sufficiently the usual processing and operation of television display tubes. On the other hand, they can improve the life and performance of electron devices with good vacuum and/or relatively low accelerating potentials. Moreover, activated top-layer scandate cathodes are relatively insensitive to exposure to (moist) air.     

Electrochemical properties of carbon-coated LiFePO4 synthesized by a modified mechanical activation process

Carbon-coated lithium iron phosphate (LiFePO₄/C) composites were synthesized by conventional mechanical activation (MA) process and also by a modified MA process. Phase-pure particles were obtained of ∼100 nm size with a nano-meter thick web of carbon surrounding the particles. The composite prepared by the modified MA process shows good performance as cathode material in lithium cells at room temperature. A high performance was achieved at 0.1 C-rate with >96% utilization of the active material. A stable cycle performance even at higher C-rates was achieved with a cathode that has a total carbon content of only 12 wt%. The use of the modified MA process to synthesize LiFePO₄/C has promise to be an efficient process to decrease the total carbon content of the cathode, resulting in the enhanced energy density.     

Hydrothermal preparation and photoluminescent properties of MgAl2O4: Eu spinel nanocrystals

Nanoplates of the MgAl₂O₄ spinel doped with Eu³⁺ ions were prepared by a microwave assisted hydrothermal method. Structural properties of the precursor calcined at 700 and 1000 ^oC powders were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). According to the obtained XRD patterns the formation of single-phase spinels after calcination was confirmed. The average spinel particle size was determined to be 11 nm after calcination at 700 °C and it increased up to 14 nm after calcination at 1000 °C. The photoluminescent properties of prepared powders with different Eu³⁺ ion concentrations (0-5% mol) were investigated using excitation and emission spectroscopy at room and low temperatures (77 K).     

Synthesis and electrochemical properties of Li4Ti5O12/C composite by the PVB rheological phase method

Spinel Li₄Ti₅O₁₂/C powders were synthesized successfully by a simple rheological phase method using polyvinylbutyral (PVB) as both template and carbon source. The structure and morphology characteristics of the composite were investigated by X-ray diffraction (XRD), field emission scanning electron microscopy and transmission electron microscopy. The XRD results showed that the composite had a good crystallinity. Its average particle size was about 2.1 μm with a narrow size distribution as a result of homogeneous mixing of the precursors. The in situ carbon coating produced by decomposition of PVB played an important role in improving electrical conductivity, thereby enhancing the rate capacity of Li₄Ti₅O₁₂ as anode material in Li-ion batteries. The Li₄Ti₅O₁₂/C composite, synthesized at 800 °C for 15 h under argon, containing 0.98 wt% of carbon, exhibited better electrochemical properties in comparison with the pristine Li₄Ti₅O₁₂, which could be attributed to the enhanced electrical conductive network of the carbon coating on the particle surface.     

Green and red up-conversion emissions of Er-Yb-codoped Al2O3 powders prepared by the nonaqueous sol-gel method

The 1 mol% Er³⁺- and 0-20 mol% Yb³⁺-codoped Al₂O₃ powders have been prepared by the nonaqueous sol-gel process using aluminum isopropoxide as precursor, acetylacetone as chelating agent, nitric acid as catalyzer, and hydrated erbium and ytterbium nitrate as dopant under isopropanol environment. The two crystalline types of doped Al₂O₃, γ and θ, and a stoichiometric compound, (Yb,Er)₃Al₅O₁₂, were obtained for all the Er³⁺-Yb³⁺-codoped Al₂O₃ powders at the sintering temperature of 1000 °C. The maximal intensity of both the green and red up-conversion emissions centered at about 523, 545, and 660 nm was observed for the 1 mol% Er³⁺- and 10 mol% Yb³⁺-codoped Al₂O₃ powders. The intensity ratio of the red to green up-conversion emission (I_red/I_green) increased with increasing the Yb³⁺ doping concentration for the Er³⁺-Yb³⁺-codoped Al₂O₃ powders. Furthermore, the intensity ratio of the green up-conversion emission at about 523 to 545 nm (I₅₂₃/I₅₄₅) was proportional to the Yb³⁺ doping concentration and pump electric current, which was associated with the elevated temperature of powders.     

Investigations on Pr1.6Sr0.4NiO4-YSZ-Ag composite cathode for solid oxide fuel cells

Ag-network was successfully deposited by VA-EP (vacuum assisted electroless plating) method on Pr_1.6Sr_0.4NiO₄-YSZ cathode to form (1−x) wt% Pr_1.6Sr_0.4NiO₄−x wt% YSZ-Ag (x=0, 10, 20, 30, 40) (abbr. PYx-Ag) composite cathode. XRD results suggested that there was a good chemical stability between Pr_1.6Sr_0.4NiO₄ and YSZ at temperatures below 1050 °C. PY20-Ag cathode exhibited higher exchange current density, lower overpotential and ASR (Area Specific Resistance) than PY20 cathode. At 650 °C, the ASR of PY20-Ag cathode was 2.5 Ω cm², which was only about 42% of that of PY20, 5.9 Ω cm². PY20-Ag can be a promising candidate for SOFC cathode.     

BaMoO4 powders processed in domestic microwave-hydrothermal: Synthesis, characterization and photoluminescence at room temperature

In this paper, BaMoO₄ powders were prepared by the coprecipitation method and processed in a domestic microwave-hydrothermal. The obtained powders were characterized by X-ray diffraction (XRD), Fourier transform Raman (FT-Raman) spectroscopy, ultraviolet-visible (UV-vis) absorption spectroscopy and photoluminescence (PL) measurements. The morphology of these powders were investigated by scanning electron microscopy (SEM). SEM micrographs showed that the BaMoO₄ powders present a polydisperse particle size distribution. XRD and FT-Raman analyses revealed that the BaMoO₄ powders are free of secondary phases and crystallize in a tetragonal structure. UV-vis was employed to determine the optical band gap of this material. PL measurements at room temperature exhibited a maximum emission around 542 nm (green emission) when excited with 488 nm wavelength. This PL behavior was attributed to the existence of intrinsic distortions into the [MoO₄] tetrahedron groups in the lattice.     

Characteristics of spherical-shaped Li4Ti5O12 anode powders prepared by spray pyrolysis

Spherical-shaped Li₄Ti₅O₁₂ anode powders with a mean size of 1.5 μm were prepared by spray pyrolysis. The precursor powders obtained by spray pyrolysis had no peaks of crystal structure of Li₄Ti₅O₁₂. The powders post-treated at temperatures of 800 and 900 °C had the single phase of spinel Li₄Ti₅O₁₂. The powders post-treated at a temperature of 1000 °C had main peaks of the Li₄Ti₅O₁₂ phase and small impurity peaks of Li₂Ti₃O₇. The spherical shape of the precursor powders was maintained after post-treatment at temperatures below 800 °C. The Brunauer-Emmett-Teller (BET) surface areas of the Li₄Ti₅O₁₂ anode powders post-treated at temperatures of 700, 800 and 900 °C were 4.9, 1.6 and 1.5 m²/g, respectively. The initial discharge capacities of Li₄Ti₅O₁₂ powders were changed from 108 to 175 mAh/g when the post-treatment temperatures were changed from 700 to 1000 °C. The maximum initial discharge capacity of the Li₄Ti₅O₁₂ powders was obtained at a post-treatment temperature of 800 °C, which had good cycle properties below current densities of 0.7 C.     

Effects of Na2CO3 flux addition on the structure and photoluminescence properties for Eu-doped YVO4 phosphor

The luminescence properties of (Y_0.9Eu_0.1)VO₄ phosphor with Na₂CO₃ flux prepared using the solid-state reaction were investigated. The XRD patterns show that all of the peaks are attributed to the YVO₄ phase. The best crystallinity was obtained with 2 wt% Na₂CO₃ flux addition. The surface morphology of (Y_0.9Eu_0.1)VO₄ phosphor changed from fluffy to a bar shape structure after Na₂CO₃ flux addition due to the tetragonal crystal system of YVO₄. The calcined powders emit bright red luminescence centered at 618 nm due to the ⁵D₀→⁷F₂ electric dipole transition under an excitation wavelength of 318 nm; its intensity was increased about 15% with 2 wt% Na₂CO₃ flux addition. Red shift behavior was observed for the charge transfer state (CTS) absorption, which was due to the grain size of (Y_0.9Eu_0.1)VO₄ phosphor increasing with increasing flux content. For 2 wt% Na₂CO₃ flux addition, the red emission of the (Y_0.9Eu_0.1)VO₄ phosphor had CIE chromaticity coordinates of (0.66, 0.34), which are very close to the NTSC system standard red chromaticity coordinates of (0.67, 0.33).     

Comparison of different NaGdF4:Eu synthesis routes and their influence on its structural and luminescent properties

Eu³⁺:NaGdF₄ samples were obtained via co-precipitation in aqueous solution (CP), reversed micelle (RM) method, reaction between solid GdF₃ and NaF solution (SR) as well as a solid-state reaction at high temperatures (SS). The synthesised materials were characterised using X-ray powder diffractometry, TEM microscopy, infrared spectroscopy and TGA analysis. For discussion of optical properties excitation and emission spectra were recorded and emission decay times were measured. The CP and RM methods allow to obtain powders with crystallite size of ∼10 nm, which may be smoothly increased to about 1 μm during post-fabrication heat treatment. Differences in structural and especially in optical properties of phosphors prepared by different techniques are emphasised and applicability of wet-chemistry routes for synthesis of fluoride powders is argued.     

Influence of initial pH on the particle size and fluorescence properties of the nano scale Eu(III) doped yttria

Europium doped ytrrium oxide (Eu:Y₂O₃) was synthesized by a chemical wet method in the presence of tween-80 and ?-caprolactam in pH range 4-10. It has been observed that the variation in surface area, pore size, and pore volume of the final product, was strongly dependent on the initial pH of the solution. The powder with a large surface area (∼230 m²/g) and low pore diameter (∼16 nm) was obtained when the powder was processed at pH ∼4. The crystallite sizes of the powders processed at pH ∼4 and 10, were found to be 35 and 198 nm, respectively. The structural, chemical and thermal studies of the powders were characterized by X-ray diffraction (XRD), Fourier transformed infrared spectrophotometer (FTIR), Carbon analyzer and Thermogravimetry (TGA). High resolution transmission electron microscopic (HRTEM) study of heat treated powders showed a polygonal morphology with particle size of 40 nm when powder was derived at pH ∼4. Observations of fluorescence suggested that the ⁵D₀→⁷F₂ transition within europium was found to be highly dependent on the initial pH.     

A study of Eu2O3, Sc2O3 co-doped tungsten matrix impregnated cathode

Eu₂O₃ and Sc₂O₃ co-doped W matrix impregnated cathodes have been prepared by the powder metallurgy method. The constitution of active elements on activated cathode surface is analyzed by in-situ Auger electron spectroscopy. It is found that although Eu exists in the matrix, no Eu is found on the cathode surface due to the formation of a stable Eu containing compound. Sc, Ba and O diffuse to the surface of the cathode and form an active surface layer during the activation period whereas the stable Eu-compound cannot liberate free Eu, which can diffuse from the cathode to the surface. The active substance of Sc, Ba and O on the cathode surface contribute to the emission property.     

Characterization and luminescent properties of SiO2:ZnS:Mn and ZnS:Mn nanophosphors synthesized by a sol-gel method

ZnS and SiO₂-ZnS nanophosphors, with or without different concentration of Mn²⁺ activator ions, were synthesized by using a sol-gel method. Dried gels were annealed at 600 °C for 2 h. Structure, morphology and particle sizes of the samples were determined by using X-ray diffraction (XRD), highresolution transmission electron microscopy (HRTEM) and field emission scanning electron microscopy (FESEM). The diffraction peaks associated with the zincblende and the wurtzite structures of ZnS were detected from as prepared ZnS powders and additional diffraction peaks associated with ZnO were detected from the annealed powders. The particle sizes of the ZnS powders were shown to increase from 3 to 50 nm when the powders were annealed at 600 °C. An UV-Vis spectrophotometer and a 325 nm He-Cd laser were used to investigate luminescent properties of the samples in air at room temperature. The bandgap of ZnS nanoparticles estimated from the UV-Vis data was 4.1 eV. Enhanced orange photoluminescence (PL) associated with ⁴T₁→⁶A₁ transitions of Mn²⁺ was observed from as prepared ZnS:Mn²⁺and SiO₂-ZnS:Mn²⁺ powders at 600 nm when the concentration of Mn²⁺ was varied from 2-20 mol%. This emission was suppressed when the powders were annealed at 600 °C resulting in two emission peaks at 450 and 560 nm, which can be ascribed to defects emission in SiO₂ and ZnO respectively. The mechanism of light emission from Mn²⁺, the effect of varying the concentration on the PL intensity, and the effect of annealing are discussed.     

Lasing at 1065 nm in bulk Nd-doped telluride-tungstate glass

We have achieved, for the first time to our knowledge, lasing in a new type of telluride-tungstate glass host doped with neodymium: Nd³⁺:(0.8)TeO₂-(0.2)WO₃. Lasing was obtained at 1065 nm with two samples containing 0.5 mol% and 1.0 mol% Nd₂O₃. During gain-switched operation, slope efficiencies of 12% and 10% were obtained with the 0.5 mol% and 1.0 mol% doped samples, respectively, at a pulse repetition rate of 1 kHz. Judd-Ofelt analysis was further employed to determine the emission cross section σ_e at 1065 nm from the absorption spectra and lifetime data. The emission cross section from the Judd-Ofelt analysis came to 3.23 ± 0.09 × 10⁻²⁰ cm², in reasonable agreement with the value of 2.0 ± 0.13 × 10⁻²⁰ cm² obtained from the analysis of laser threshold data.     

Preparation and textural characterisation of activated carbon from vine shoots (Vitis vinifera) by H3PO4—Chemical activation

An abundant and low-cost agricultural waste as vine shoots (Vitis vinifera) (VS), which is generated by the annual pruning of vineyards, has been used as raw material in the preparation of powder activated carbon (AC) by the method of chemical activation with phosphoric acid. After size reduction, VS were impregnated for 2 h with 60 wt.% H₃PO₄ solution at room temperature, 50 and 85 °C. The three impregnated products were carbonised at 400 °C. The product impregnated at 50 °C was heated either first at 150-250 °C and then at 400 °C or simply at 350-550 °C in N₂ atmosphere. The time of isothermal treatment after each dynamic heating was 2 h. The carbons were texturally characterised by gas adsorption (N₂, −196 °C), mercury porosimetry, and density measurements. FT-IR spectroscopy was also applied. Better developments of surface area and microporosity are obtained when the impregnation of VS with the H₃PO₄ solution is effected at 50 °C and for the products heated isothermally at 200 and 450 °C. The mesopore volume is also usually higher for the products impregnated and heated at intermediate temperatures.     

H2 storage efficiency and sorption kinetics in composite materials

We have prepared two different kinds of composite materials for hydrogen storage and studied their H₂ storage capacity and desorption kinetics. The first composite material consists of magnesium-containing transition metal nanoclusters distributed in the Mg matrix (Mg:TM): this composite material shows better H₂ desorption performances than pure Mg. This improvement is attributed to the role of the MgH₂-TM nanocluster interface as preferential site for hexagonal Mg (h-Mg) nucleation and to the rapid formation of interconnected h-Mg domains where H diffusion during desorption occurs. The second composite material consists of LaNi₅ particles (size<30 μm) distributed in a polymeric matrix. The H₂ storage capacity is negligible at low metal content (50 wt%) when the metal particles are completely embedded in the polymeric matrix. The H₂ storage capacity is comparable to that of the pure LaNi₅ powders at high metal content (80 wt%) when a percolative distribution is assumed by the LaNi₅ particles: this evidence points out the role of metal-metal interfaces and of interconnected metallic networks for H transport.