Aspects of the thermal and photostabilisation of high styrene-butadiene copolymer (SBC)

The thermal and photo-oxidative stabilisation of high styrene-butadiene copolymer (SBC) with high styrene content (K-Resin) has been studied using a variety of analytical and spectroscopic methods including yellowness, luminescence and FT-IR spectroscopy coupled with hydroperoxide analysis in order to understand the nature and effectiveness of the processes involved. The next stage of the program was to evaluate the effects of various chemical/solvent treatments on the role of metal ions/residual catalysts and hydroperoxides in the thermal and photostabilisation of SBS as well as combinations of phenolic antioxidants and phosphites/phosphonites. Other additives, such as HALS and a metal deactivator, were also added to the combinations of phenolic and phosphite antioxidants in order to study their behaviour and efficiency. The chemical treatments appeared to stabilise SBS against thermal oxidation to a greater or lesser extent. Phosphoric acid treatment via reflux and zinc dithiocarbamate treatments showed better performances than the rest of the treatments, the latter was particularly effective at inhibiting the discolouration. During photo-oxidation, on the other hand, chemical treatments involving phosphoric acid and pre-thermal effects showed the importance of catalyst effects. The addition of phenolic antioxidants, phosphites/phosphonites, metal deactivator and HALS was found to stabilise the SBS against thermal and photo-oxidation. In thermal oxidation, the combination of Irganox^® 1010/Irgafos^® 168 was found to effectively stabilise the polymer when the finalisation of the polymerisation was with adipic acid. When the same antioxidants were used, but with polymer finalised with BHT, strong yellowing was observed and a higher amount of hydroperoxides and oxidation products. Increasing the amount of antioxidants did not increase the stabilisation efficiency. The stabilisation efficiency of Irganox^® 1010 combined with Alkanox^® P-24 was found to be more effective than when it was combined with Irgafos^® 168. The formulations containing Irgafos^® 168/Irganox^® 1010 and Irgafos^® 168/Irganos^® 1330 were more effective in colour protection and retarding the formation of oxidation products than the combinations of Irgafos^® 168/Irganox^® 3114 and Irgafos^® 168/Lowinox^® 1790. The effect of the addition of HALS, such as Tinuvin^® 770, Tinuvin^® 622 and Chimassorb^® 944, and a metal deactivator, such as Irganox^® MD 1024, to the combination of Irgafos^® 168/Irganox^® 1010 was found to be antagonistic. In photo-oxidation, a combination of Irganox^® 1010/Irgafos^® 168 protected the polymer efficiently, when the polymerisation of the polymer was finalised with adipic acid. When the polymerisation was finalised with BHT, a higher amount of hydroperoxides and oxidation products was found. An increase in the amount of antioxidants did not enhance the stability of the polymer. The addition of Alkanox^® P-24 exhibited an opposite effect to that seen in thermal oxidation, as the stabilisation efficiency was less effective than with Irgafos^® 168. The formulation containing Irgafos^® 168/Irganox^® 1010 was found to be the most efficient compared with the other phenolic antioxidants. The addition of Tinuvin^® 770 to the formulation Irgafos^® 168/Irganox^® 1010 was found to have a synergistic effect. The addition of polymeric HALS or Irganox^® MD 1024, a metal deactivator, had an antagonistic effect on the stabilisation of the polymer. Disruption of the excimer sites in the styrenic phase also correlated with stabilisation effects.     

Separation of two labeled components of [111In] -OctreoScan by HPLC

[¹¹¹In]-DTPA-D-Phe¹-octreotide (OctreoScan^®, Mallinkrodt) is widely used for detection of neuroendocrine tumors and has lately been proposed for radionuclide therapy. We found, using HPLC and a GF-250 column (Zorbax^®, Hewlett Packard), that OctreoScan^® can be separated in two radiolabeled components of about equal amount. The analytical conditions for a quantitative isolation indicate that the two-peptide components of OctreoScan^®have different lipophilicity. The isolated components are stable and do not transform into each other at room temperature during 6 hours (shelf-life of OctreoScan^®).     

Structure and morphology of HDPE-g-MA/organoclay nanocomposites: Effects of the preparation procedures

Nanocomposites comprising high density polyethylene (HDPE) or maleic anhydride-grafted HDPE (HDMA) as the host polymers and Cloisite^® 20A (20A) as the organoclay filler were prepared by melt-compounding, solution-blending and static annealing of polymer/clay powder mixtures. The dependence of their structure and morphology on the preparation conditions was studied by X-ray diffraction (XRD and SAXS), polarized optical microscopy (POM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). It was shown that intercalated nanocomposites based on HDPE or HDMA cannot be obtained by solution-blending, as long as solvent removal is made at room temperature. In fact, wide angle XRD patterns of solution blended composites are similar to those of mechanical blends of clay and polymer. However, as demonstrated by XRD and SAXS, fast intercalation or even complete delamination was obtained when the HDMA composites prepared from solution were annealed statically at temperatures higher than the polymer melting point. This implies that solution-blending causes efficient fragmentation of the clay agglomerates into thin tactoids (though unintercalated) homogeneously dispersed in the polymer matrix. This conclusion, supported by the finding that annealing mechanical blends of polymer and clay powders only leads to intercalated structures, was confirmed by TEM and SEM analyses. Morphology investigation revealed that, in contrast to melt-compounding, solution-blending followed by static annealing fails to produce significant orientation of clay platelets and polymer crystallites. However, repeated compression molding cycles were shown by XRD and SAXS to cause increasing levels of orientation of the platelets and the polymer matrix parallel to the sample flat surface.     

Dimensionally stable Nafion–polyethylene composite membranes for direct methanol fuel cell applications

Nafion^® impregnated Solupor^®, microporous UHMWPE film, (N-PE), Nafion^®117 (N117) and a membrane prepared using a DE2020 Nafion^® dispersion (DE2020) were characterized with respect to their swelling degree (SD), methanol cross-over, proton conductivity and DMFC performance at various methanol concentrations in order to understand the effect of impregnation of an ion-conductive polymer membrane to the fuel cell performance.     

EPR and Mössbauer characterization of RTV polysiloxane foams and their constituents

We have used electron paramagnetic resonance (EPR) and ⁵⁷Fe Mössbauer spectroscopies to investigate potential aging mechanisms in filled RTV polysiloxane foams, diatomaceous earth, and their other constituents. Intense, broad EPR resonances in the RTV foams were recorded at room temperature as a function of microwave power. These signals were shown to come from the diatomaceous earth filler (Celite^® 350) in the RTV foams. ⁵⁷Fe Mössbauer measurements for neat Celite^® 350 showed the presence of iron compounds in the form of lepidocrocite. Further EPR measurements showed that the intense, broad signals from Celite^® 350 and the RTV foams were due to lepidocrocite that has been annealed to 175 °C and is in an excited state. EPR measurements of annealed samples of Celite^® 350 also indicated that structural (chemisorbed) water is not easily released by the lepidocrocite. Therefore, the presence of intermediate forms of iron oxides in Celite^® 350 and RTV foams indicates that water is not active in these materials.     

Microwave-assisted rapid electrophilic fluorination of 1,3-dicarbonyl derivatives with Selectfluor

A microwave-assisted fluorination method for 1,3-dicarbonyl compounds using Selectfluor^® has been developed. 2-Monofluorinated products can be obtained in high yield in neutral reaction conditions with addition of 1 eq. of Selectfluor^®. Treatment of 1,3-dicarbonyls with 3 eq. of Selectfluor^® in the presence of tetrabutylammonium hydroxide (TBAH) as the base results in the formation of 2,2-difluorinated derivatives only.     

Novel perfluoropolyethers containing 2,2,4-trifluoro-5-trifluoromethoxy-1,3-dioxole blocks: synthesis and characterization

Peroxidic perfluoropolyethers (PFPEs) are industrial intermediates used by Solvay Solexis for the preparation of different classes of (per)fluoropolyethers (Fomblin^®, Galden^®, Solvera^®, Fluorolink^®). The chemistry of these peroxidic compounds has been recently exploited for the synthesis of novel PFPE block copolymers. In the present work we report the synthesis, the structural and physical-chemical characterization of block copolymers obtained by the reaction of peroxidic PFPEs with 2,2,4-trifluoro-5-trifluoromethoxy-1,3-dioxole, a cyclic homopolymerizable perfluoroolefin. These block copolymers combine the most attractive properties of the PFPEs, like the excellent lubrication, the high thermal stability and the optical transparency, with new specific properties which are related to the perfluorodioxolenic blocks.     

Radiolabeling of HER2-specific Affibody molecule with F-18

The presence of human epidermal growth factor type 2 (HER2) on 20-30% of human breast cancer is a prognostic indicator of more rapid disease progression and a therapeutic indicator for anti-HER2 monoclonal antibodies. Because the literature has demonstrated some discordance between primary and metastatic tumors in the same patient for expression of the HER2 marker, we set out to develop an imaging agent that could be used to assess the marker concentration in vivo in an individual patient. The pharmaceutical company Affibody^® AB has optimized the specificity of Affibody^® molecules for HER2. Two Affibody^® molecules, a 7 kDa and an 8 kDa protein, were designed with a single carboxy terminal cysteine in order to provide a specific location for the purposes of labeling for various types of imaging. We have prepared [¹⁸F]FBEM utilizing a coupling reaction between [¹⁸F]fluorobenzoic acid and aminoethylmaleimide. We then optimized the conjugation of this radiolabeled maleimide to the free sulfhydryl of cysteine by incubating at pH 7.4 in phosphate buffered saline containing 0.1% sodium ascorbate. An overall uncorrected yield of radiolabeled Affibody^® molecule of approximately 10% from [¹⁸F]fluoride was achieved in a 2 h synthesis. These conjugated Affibody^® molecules were obtained with a specific activity of 2.51 ± 0.92 MBq/μg. Characterization of the product by HPLC-MS supported the conjugation of [¹⁸F]FBEM with the Affibody^® molecule. The radiolabeled Affibody^® molecule retained its binding specificity as demonstrated by successful imaging of xenografts expressing HER2.     

NOR and nitroxide-based HAS in accelerated photooxidation of carbon-chain polymers; Comparison with secondary HAS: An ESRI and ATR FTIR study

Understanding processes resulting in heterogeneous degradation in polymers is of extreme importance for improving their stabilization and minimizing negative impact of photooxidation on the material properties. We adopted modern physical techniques for studies of spatial distribution of intermediates and products of photodegradation during accelerated ageing of four commodity polymers, polypropylene (PP), polyethylene (PE), polystyrene (PS) and poly(ethylene-co-norbornene) (Topas^®, TP) stabilized with hindered amine stabilizer (HAS). Concentration profiles of nitroxides inside polymer plaques along the direction perpendicular to their surface were determined by electron spin resonance imaging (ESRI) as a function of the duration of the accelerated photooxidation. We present data characterizing stabilization activity of three alkoxyamine derivatives of HAS (Tinuvin^® NOR 123, Tinuvin^® NOR 371, Flamestab^® NOR 116), Chimasorb^® 119 structurally similar to Flamestab^® NOR 116, and nitroxide-based HAS Dastib^® 1045 and compare them with the data characterizing stabilization activity of the secondary HAS (>NH) Tinuvin^® 770. ESRI data are complemented by ATR FTIR spectroscopic detection of oxidation products on the surface and inside the plaques and by data characterizing diffusive optical transmittance of the polymer plaques in the spectral region 280-400 nm (terrestrial range of the solar UV radiation).     

Isolation of Pu-isotopes from environmental samples using ion chromatography for accelerator mass spectrometry and alpha spectrometry

A radiochemical method for the isolation of plutonium-isotopes from environmental samples, based on the use of specific extraction chromatography resins for actinides (TEVA^®, Eichrom Industries, Inc.), has been set up in our laboratory and optimised for their posterior determination by alpha spectrometry (AS) or accelerator mass spectrometry (AMS). The proposed radiochemical method has replaced in our lab a well-established one based on the use of a relatively un-specific anion-exchange resin (AG^® 1X8, Bio-rad Laboratories, Inc.), because it is clearly less time consuming, reduces the amounts and molarities of acid wastes produced, and reproducibly gives high radiochemical yields.In order to check the reliability of the proposed radiochemical method for the determination of plutonium-isotopes in different environmental matrixes, twin aliquots of a set of samples were prepared with TEVA^® and with AG^® 1X8 resins and measured by AS. Some samples prepared with TEVA^® resins were measured as well by AMS. As it is shown in the text, there is a comfortable agreement between AS and AMS, which adequately validates the method.     

Influence of compatibilizer degradation on formation and properties of PA6/organoclay nanocomposites

Nanocomposites based on polyamide 6 (PA6) and commercial layered silicates have been prepared by both in situ polymerization and melt compounding. The main aim of the present work has been centred on compatibilizer degradation, caused by the preparation conditions, in terms of nanocomposite end features. Two montmorillonite (MMT)-type, organically-modified clays (OMLS), namely Cloisite 30B^® and Nanofil 784^®, and a sodium MMT (Cloisite Na^®) have been studied. Thermal properties of the layered silicates have been evaluated by TGA, IR, WAXD and pyrolysis-gas-mass. In order to better assess the influence of high temperature processes on clay modifications, a thermal treatment which mimics the conditions used during the in situ polymerization (4 h at 250 °C) has been applied on layered silicates. The above treatment, besides the elimination of absorbed water from all the clays, turned out to prove noteworthy differences in compatibilizer modification for the two organoclays. Indeed, in the case of Closite 30B^® only a removal of organic molecules outside the silicate galleries and a likely reorganization of those present inside the galleries have been detected, while a relevant chemical modification of Nanofil 784^® compatibilizer has been conversely found.As far as nanocomposite characteristics are concerned, the latter have been found to depend on both the preparation method and clay type. In the case of in situ polymerization, also thermally-treated layered silicates, coded (T), have been used, in order to put more clearly in evidence the role of compatibilizer decomposition on nanocomposite formation and properties. Indeed, nanocomposite samples containing Closite 30B^®(T) have been found to be completely exfoliated, while the same thermal treatment seems to make worse the properties of those based on Nanofil 784^®(T). Furthermore, with respect to nanocomposites based on pristine clays, samples containing thermally-treated silicates turned out to be different in terms of both molecular mass and crystal structure of the polymer matrix. Namely, PA6 γ-form seems to be promoted for all nanocomposites prepared in such a way, probably because of water removal at high temperature, which makes -OH groups of the layered silicate more free to interact with polyamide chains, thus causing a restriction of their mobility.     

A spectrophotometric method for determination of the solubilizing activity of cellulase complexes

Summary A standardized spectrophotometric method for determination of the solubilizing activity of microbial cellulase complexes has been developed. It is based on the release of coloured compounds from microcrystalline cellulose (Avicel SF^®) dyed with Levafixbrillantrot E-2B^®.

---

Eine spektrophotometrische Methode zur Bestimmung der solubilisierenden Aktivität des Cellulase-Komplexes (Kurze Mitteilung)

Zusammenfassung Es wurde eine standardisierte spektrophotometrische Methode zur Bestimmung der Aktivität des Cellulase-Komplexes von Mikroorganismen ausgearbeitet. Die Methode beruht auf der Möglichkeit, mit Levafixbrillantrot E-2 B^® gefärbte mikrokristalline Cellulose (Avicel SF^®) als Substrat zu verwenden.

     

A modified accelerating rate calorimeter (ARC) with capabilities for handling gaseous samples under vacuum or an inert atmosphere

A simple modification was made to the accelerating rate calorimeter (ARC^®), which has allowed for gaseous samples to be tested without the introduction of air. The modified ARC^® can also be used to test solids, liquids, or mixtures of two phases under a particular atmospheric environment with more convenience than in the original ARC^®. After the experiment, the gaseous products and/or any unreacted gaseous sample can easily be collected for further characterization. This facilitates one's ability to understand the mechanism of the exothermal reactions. The utility of this modified ARC^® was demonstrated by examining the thermal properties and polymerization of 1,1-difluoroethylene.     

An update on AOAC INTERNATIONAL new program activities

Significant progress has been made with the introduction of new AOAC INTERNATIONAL programs since plans were announced at BERM-5 in Aachen, Germany. The AOAC^® Technical Division on Reference Materials has been formed, the AOAC^® Peer-Verified Methods Program has been established and ready to accept methods for study, and the AOAC^® Test Kit Performance Testing Program has become operational.     

The effect of spatial confinement of Nafion in porous membranes on macroscopic properties of the membrane

Polyelectrolytes were incorporated into porous reinforcing materials to study the properties of ionomers in confined spaces and to determine the effect of the porous material on the behaviour of the membranes. Nafion^® was imbibed into porous polypropylene (Celgard^®), ultra-high-molecular weight polyethylene (Daramic^®), and polytetrafluoroethylene (PTFE) films. Through the use of reinforcing materials, it is possible to prepare membranes that are thinner, but stronger than pure ionomer membranes. Thin reinforced membranes have advantages such as lower areal resistance (as low as 0.14 Ω cm² for 57 μm CG3501 + Nafion^® compared to 0.34 Ω cm² for 89 μm cast Nafion^®) and lower dimensional changes due to swelling (as low as a 4% change in length and width for WDM + Nafion^® compared to 13% for cast Nafion^®). Using reinforcing materials results in a reduction in important membrane properties compared to bulk Nafion^®, such as proton conductivity (as low as 0.016 S cm⁻¹ for CG3401 + Nafion^® compared to 0.076 S cm⁻¹ for cast Nafion^®), effective proton mobility (as low as 3.2 × 10⁻⁴ cm² V⁻¹ s⁻¹ CG3401 + Nafion^® compared to 7.6 × 10⁻⁴ cm² V⁻¹ s⁻¹ for cast Nafion^®), and water vapour permeance (as low as 0.036 g h⁻¹ Pa⁻¹ m⁻² for WDM + Nafion^® compared to 0.056 g h⁻¹ Pa⁻¹ m⁻² for cast Nafion^®). By normalizing the membrane properties with respect to ionomer content, it was possible to examine the properties of the Nafion^® inside the pores of the membranes. The proton conductivity (as low as 0.032 S cm⁻¹ for CG3401 + Nafion^®), effective proton mobility (as low as 3.6 × 10⁻⁴ cm² V⁻¹ s⁻¹ for CG3401 + Nafion^®), and water vapour permeability (as low as 2.7 × 10⁻⁶ g h⁻¹ Pa⁻¹ m⁻¹ for PTFE MP 0.1 + Nafion^®) of the ionomer in the membrane are also diminished compared to bulk Nafion^® due to decreased connectivity of the ionomer and a restriction in macromolecular motions caused by the pore walls. A series of porous materials with increasing pore were also examined. As the pore size of the PTFE MP materials increased from 0.1 μm to 10 μm, the proton conductivity (0.022 S cm⁻¹ to 0.041 S cm⁻¹), effective proton mobility ((4.1 to 5.6) × 10⁻⁴ cm² V⁻¹ s⁻¹), and water vapour permeability ((2.4 to 4.3) × 10⁻⁶ g h⁻¹ Pa⁻¹ m⁻¹) of the reinforced membranes improved with increasing pore size and the properties of the ionomer inside the membranes approached the value of bulk Nafion^®.     

The rheology of Torlon solutions and its role in the formation of ultra-thin defect-free Torlon hollow fiber membranes for gas separation

Fundamental understanding of the material science and rheological engineering to fabricate Torlon^® 4000T-MV and 4000TF hollow fiber membranes with an ultra-thin and defect-free dense-selective layer for gas separation has been revealed. We have firstly investigated the rheology of Torlon^® 4000T-MV and 4000TF dope solutions, and then determined the effect of temperature-correlated shear and elongational viscosities on the formation of Torlon^® fibers for gas separation. Interestingly, Torlon^® 4000T-MV and 4000TF possess different rheological characteristics: the elongational viscosity of Torlon^® 4000T-MV/NMP solution shows strain thinning, while Torlon^® 4000TF/NMP solution shows strain hardening. The balanced viscoelastic properties of dope solutions, which are strongly dependent on the spinning temperature, have been found to be crucial for the formation of a defect-free dense layer. The optimum rheological properties to fabricate Torlon^® 4000T-MV/NMP hollow fibers appear at about 48–50 °C, and the resultant fibers have an O₂/N₂ selectivity of 8.37 and an apparent dense layer thickness of 781 Å. By comparison, the best Torlon^® 4000TF fibers were spun at 24 °C with an O₂/N₂ selectivity of 8.96 and a dense layer of 1116 Å. The CO₂/CH₄ selectivity of the above two Torlon^® variants is 47 and 53.5, respectively.     

The evaluation of miscibility of blends of poly(ether imide) (Ultem1000) and a copolyester of bisphenol-A with terephthalic and isophthalic acid (ArdelD-100) by viscosimetry

The intermolecular interactions and miscibility behavior between poly(ether imide) (Ultem^®1000) and a copolyester of bisphenol-A with a mixture of terephthalic and isophthalic acid (Ardel^®D-100) in compositions of 100/0, 80/20, 60/40, 40/60, 20/80 and 0/100 have been investigated in dilute solutions in chloroform. An Ubbelohde-type home-made viscometer was used to determine the specific viscosities of the blends in a constant temperature bath. Several viscosity interaction parameters used as the criteria of miscibility were determined from viscosity measurements. The parameters suggested that Ultem^®1000 and Ardel^®D-100 were miscible. The miscibility of the polymers was confirmed by the results of differential scanning calorimetry measurements.     

Novel coatings for stir bar sorptive extraction to determine pharmaceuticals and personal care products in environmental waters by liquid chromatography and tandem mass spectrometry

Two new commercially available polar coatings for stir bar sorptive extraction (SBSE), consisting of polyacrylate (PA) with a proportion of polyethyleneglycol (PEG) (Acrylate Twister^®) and PEG modified silicone (EG Silicone Twister^®), were evaluated and compared with the classic coating based on polydimethylsiloxane (PDMS Twister^®) for the extraction of a group of pharmaceuticals and personal care products (PPCPs) from wastewater samples.     

Uranium aqueous speciation in the vicinity of the former uranium mining sites using the diffusive gradients in thin films and ultrafiltration techniques

The performance of the Diffusive Gradients in Thin films (DGT) technique with Chelex^®-100, Metsorb™ and Diphonix^® as binding phases was evaluated in the vicinity of the former uranium mining sites of Chardon and L'Ecarpière (Loire-Atlantique department in western France). This is the first time that the DGT technique with three different binding agents was employed for the aqueous U determination in the context of uranium mining environments. The fractionation and speciation of uranium were investigated using a multi-methodological approach using filtration (0.45 μm, 0.2 μm), ultrafiltration (500 kDa, 100 kDa and 10 kDa) coupled to geochemical speciation modelling (PhreeQC) and the DGT technique. The ultrafiltration data showed that at each sampling point uranium was present mostly in the 10 kDa truly dissolved fraction and the geochemical modelling speciation calculations indicated that U speciation was markedly predominated by CaUO₂(CO₃)₃²⁻. In natural waters, no significant difference was observed in terms of U uptake between Chelex^®-100 and Metsorb™, while similar or inferior U uptake was observed on Diphonix^® resin. In turn, at mining influenced sampling spots, the U accumulation on DGT-Diphonix^® was higher than on DGT-Chelex^®-100 and DGT-Metsorb™, probably because their performance was disturbed by the extreme composition of the mining waters. The use of Diphonix^® resin leads to a significant advance in the application and development of the DGT technique for determination of U in mining influenced environments. This investigation demonstrated that such multi-technique approach provides a better picture of U speciation and enables to assess more accurately the potentially bioavailable U pool.     

Comparison of three different enrichment strategies for serum low molecular weight protein identification using shotgun proteomics approach

Serum low-molecular weight (LMW) proteins potentially contain useful biological information and their identification can be used to discover novel potential biomarkers. Given the high complexity of serum samples, in the last years several different prefractionation and enrichment strategies have been developed. In this study three different methods, i.e. hydrogel nanoparticles, Proteominer^® peptide ligand affinity beads and Sartorius Vivaspin^® centrifugal ultrafiltration device, were compared and evaluated in order to select the best strategy for the enrichment and prefractionation of LMW proteins. A shotgun proteomics approach was adopted, with in-solution proteolytic digestion of the whole protein mixture and determination of the resulting peptides by nanoHPLC coupled with a high-resolution Orbitrap LTQ-XL mass spectrometer. Data analysis, focusing on the LMW proteome (MW ≤ 40 kDa), has shown that the hydrogel nanoparticles performed better in enriching the LMW protein profiles, with 115 proteins identified against 93 and 95 for Proteominer^® beads and Sartorius Vivaspin^® device, respectively.