薄壁快脉冲252Cf裂变电离室的研制及性能测试

介绍了用于中子探测器效率刻度的薄壁快脉冲252Cf裂变电离室。 在用飞行时间法测量中子能谱时, 该裂变电离室能够给出252Cf裂变中子发射时刻信号, 输出脉冲上升时间约为5.5 ns, 电离室由厚度为0.15 mm的不锈钢构成。 测试结果表明, 对裂变碎片的探测效率为99.2%, α粒子脉冲幅度和碎片脉冲幅度可清晰分开。A thin wall, fast pulse 252Cf ionization chamber, which was designed for calibrating efficiency of neutron detectors, was described. The ionization chamber can be used as the start detector in time of flight measurements of the 252Cf fission neutron spectrum. The chamber is composed of 0.15 mm thick stainless steel, the rise time of pulse signals is about 5.5 ns. As the test result shows, the detection efficiency of fission fragments is 99.2%, and pulse signals caused by fissions are distinguished clearly from those caused by α decays.     

LS301快中子探测器的效率刻度

主要介绍了利用252Cf标准裂变中子能谱刻度快脉冲LS301型液闪中子探测器的探测效率的实验方法和结果, 简要介绍了实验数据的处理过程, 得到了阈值分别为0.5, 0.7, 1.0和1.6 MeV, 以及中子能量在10 MeV以下的探测器效率, 并对测量结果进行了误差分析。同时为了检验实验结果的准确性, 将实验结果与理论计算结果进行比较, 两者在不确定度范围内符合得很好。Neutron detection efficiency of LS301 fast neutron detector was calibrated by measuring the neutron energy spectrum of 252Cf source, which has a standard fission neutron spectrum. A low mass, fast ionization chamber is used as the fission fragments detector in the time of flight(TOF) spectrometer and afforded the start signal of neutron flight. The stop signal was offered by the anode of LS301. A measured TOF spectrum was turned to the neutron energy spectrum which will be compared with the standard one. Consequently, the fast neutron detection efficiency of LS301 was obtained. Calibration procedures of experimental and data processing was given. Relative detection efficiencies were obtained separately for threshold settings of 0.5, 0.7, 1.0 and 1.6 MeV for neutron energies under 10 MeV. Experimental results accorded with theoretical efficiency curves which were calculated with the Monte Carlo code NEFF50.     

Equivalent properties of single event burnout induced by different sources

The experimental results of single event burnout induced by heavy ions and 252Cf fission fragments in power MOSFET devices have been investigated. It is concluded that the characteristics of single event burnout induced by 252Cf fission fragments is consistent to that in heavy ions. The power MOSFET in the ＂turn-off＂ state is more susceptible to single event burnout than it is in the ＂turn-on＂ state. The thresholds of the drain-source voltage for single event burnout induced by 173 MeV bromine ions and ^252Cf fission fragments are close to each other, and the burnout cross section is sensitive to variation of the drain-source voltage above the threshold of single event burnout. In addition, the current waveforms of single event burnouts induced by different sources are similar. Different power MOSFET devices may have different probabilities for the occurrence of single event burnout.     

Varying Track Etch Rates along the Fission Fragments＇ Trajectories in CR-39 Detectors

We determine the behavior of track etch rate VT along the tracks in CR-39 detectors exposed to fission fragments from ^252Cf source. CR-39 detectors are etched at 70℃ in different concentrations of Na2COa-mixed 6M NaOH solutions for different etching time intervals of 5-10min starting from 15 min up to 210min. Two values of track etch rate are determined along the fission fragment trajectories. The variation in VT is correlated with the energy loss rate of the fission fragment in the detector material.     

一种大型位置灵敏平行板雪崩计数器

中国科学院近代物理研究所气体探测器组研制了一种大型位置灵敏的平行板雪崩计数器（PPAC）。它主要由中心阴极和X,Y位置阳极构成,灵敏面积为244 mm×284 mm,阴极为双面镀金1.5 μm厚的Mylar膜,阳极为直径20 μm,间距1 mm的镀金钨丝。位置读出选用延迟块读出法。这种探测器经测试在灵敏面积内位置分辨小于4 mm,时间分辨为0.42 ns,已在兰州放射性束流线（RIBLL）上清华大学的核反应实验中使用。该实验中使用了主束40Ar直接轰击Au靶,产生裂变碎片,使用了4个这种大型位置灵敏的PPAC,用来探测裂变碎片的飞行时间和速度,实验表明,PPAC对裂变碎片有90.3%的效率,给出了裂变碎片的位置分布,为理论分析工作提供了非常好的实验数据。A kind of large position sensitive parallel plate avalanche counter(PPAC) was developed at Gas Detector Research Group, Institute of Modern Physics of CAS. Each of the detector with large sensitive area of 244 mm×284 mm, consists of one central cathode, X anode and Y anode. The cathode plane in the middle of detector is a 1.5 μm thick Mylar foil coated with a thin Au-layer on both sides. The position resolution of the PPAC is better than 4 mm, and the time resolution is 0.42 ns. The detectors were used in the fission experiment with 30MeV/u 40Ar beam bombarding on a gold target to measure the velocity of the fission fragments at Radioactive Ion Beam Line In Lanzhou(RIBLL). Four PPACs were used and the experiment result showed that a rather high detection efficiency (90.3%) is achieved. The position distribution of fission fragments is given by PPACs, which provides very good experimental data for further theoretical analysis.     

Transport Efficiency of Gas-jet Tape Transport System

The Gas-jet Tape Transport System (GTTS) was used in several on-line experiments. The transport efficiency of GTTS was studied with three different inorganic salts, PbI2, PbC12 and NaC1, by using a ^252 Cf source. The fission fragments of ^252Cf were transported and collected by the GTTS before measurement. Nitrogen gas was used as a substitute of cxpensive Helium gas, in consideration of longer stopping range of fragments. The fragments were also directly collected on Aluminum foils with thickness of 50μm for original yield measurement.     

Etchability of Latent Fission Fragment Tracks in CR-39

We report the chemical etching behaviour of the CR-39 polymer detector exposed to fission fragments of 252Cf describing etchability of latent tracks, which are like nanocylinders. The fission fragment exposed detectors were etched in 1-7 N NaOH water solutions at temperatures 50-80℃ for 45 min in the case of track length and 180 min in the case of track diameter measurements. The reduced etch rate S （called here etchability） is determined using experimental results for all etching conditions and the etching conditions with the highest reduced etch are obtained. Physics and energetics of bulk and track etching are discussed. Possible effects causing spurious changes in determination of activation energy of etching are investigated.     

重离子周边碰撞和中心碰撞引起的不同裂变行为

本实验同时研究了4 0Ar+209Bi反应中周边碰撞和中心碰撞两者产生的关联裂变碎片,以及其与α粒子的再关联.对裂变碎片质量分布和能量分布随热裂变核初始温度演化的系统分析,发现中心碰撞和周边碰撞所形成的热核存在着不同的裂变行为. Correlated fission fragments from the 40Ar+209Bi reaction and their further correlation with α particles have been studied for peripheral and central collisions simultaneously. The existence of different fission behavior of hot nuclei formed in central and peripheral collisions was found from the systematic analysis of the mass and energy distributions of fission fragments as a function of the initial temperature of hot fissioning nuclei.     

Etch Induction Time in CR-39 Detectors Etched in Na2CO3 Mixed NaOH Solution

Six different solutions of 6M NaOH, containing different amounts of Na2CO3 at 70℃ were used for the revelation of latent damage trails in CR-39 plastic track detectors. These detectors were earlier exposed to fission fragments from ^252 Cf source for 30 min in vacuum and were then etched in the respective solutions for different etching time intervals of 5-20 min starting from 5min up to 160min. The etch induction time in each detector was obtained by extrapolating the intersection of resulting curves of track lengths and track diameters with the time axis.     

Calculation of prompt fission neutron spectrum for 233U（n,f） reaction by the semi-empirical method

The prompt fission neutron spectra for the neutron-induced fission of 233U for low energy neutrons （below 6 MeV） are calculated using nuclear evaporation theory with a semi-empirical method, in which the partition of the total excitation energy between the fission fragments for the nth＋233U fission reactions is determined by the available experimental and evaluation data. The calculated prompt fission neutron spectra agree well with the experimental data. The proportions of high-energy neutrons of prompt fission neutron spectrum versus incident neutron energies are investigated with the theoretical spectra, and the results are consistent with the systematics. The semi-empirical method could be a useful tool for the prompt evaluation of fission neutron spectra.     

Ternary fission induced by 540 MeV Fe ions on uranium

The ratio of ternary to binary fission for uranium irradiated with 540 MeV Fe ions was found to be (4.3 ±0.7)%, when fission fragments in the forward hemisphere of the laboratory system are investigated. The detector was mica, heated after irradiation for 1 hour at 500°C, so as to reveal only fission fragments as tracks. The relatively high yield of ternary fission is interpreted qualitatively on the basis of potential-energy curves for binary fission and prolate ternary fission. The two curves appear to be fairly similar for the two decay modes.     

一种基于SiPM的新型起始时间探测器研制

本文介绍了一种新型起始时间探测器的研制。该探测器的灵敏面积为60 mm×60 mm,利用120根直径为1 mm的塑料闪烁光纤分成两层错位紧致排布,且上下相邻的3根光纤作为一个探测单元,每个探测单元均采用硅光电倍增管从双端读出信号。采用90Sr放射源对单根光纤进行了性能测试,结果表明,闪烁光沿着光纤方向的有效传播速度约为17 cm/ns,对应的时间分辨优于600 ps。此外,利用中国科学院近代物理研究所第二条放射性束流线（RIBLL2）提供的240 MeV/u的15N次级束研究了该探测器的性能。束流测试结果表明:该探测器的时间分辨为（150±15）ps,纵向位置分辨为（1.8±0.2）cm,并且结合该探测器以及RIBLL2束流线外靶实验终端上的其他探测器,可以对实验中产生的5 ≤ Z ≤ 8的各种同位素进行非常好的粒子鉴别。     

25MeV/u 40)Ar+209Bi裂变反应研究

实验对25MeV/u ⁴⁰Ar+²⁰⁹Bi体系的裂变反应,利用线性动量转移的分窗选择不同的激发能,研究裂变动能分布和质量分布与热核初始激发能的关系.实验证实激发能小于380MeV时裂变总动能分布与低激发能复合核相似.激发能大于380MeV时,最可几动能呈现出随激发增加而增加,并出现高能非对称性,而且质量分布宽度随激发能增加而迅速增大.     

46.7MeV/u 12C轰击159Tb、197Au和209Bi的裂变测量及分析

用46.7MeV/u~(12)C轰击~(159)Tb、~(197)Au、~(209)Bi,测量关联裂片的速度和角度,研究了线性动量转移(LMT)、质量和出平面角分布,提取了核温度,应用级联两体统计衰变理论进行了拟合与解释,结果表明:在～50MeV/u入射能的中能重离子碰撞中,以非完全熔合方式形成了核温度高达4～5MeV的类复合核,其后通过裂变、蒸发级联统计两体衰变而退激。 The velocities and angles of fission partners emitted from reactions in ~(12)C+~(159)Tb, ~(197)Au,~(209)Bi systems with bombarding energy of 46.7MeV/u are measured. The linear momentum transferfrom projectile to target、mass and out-of-reaction plane angle distributions of fission fragments arestudied, and the temperatures of the target residues are extracted. These results have been explained by statistical binary decay model. It seems that the compound-likesystem with high temperature...     

利用252 Cf快裂变室测量BC501A液闪探测器的相对探测效率和响应函数

本文利用²⁵²Cf快裂变室和多参数数据采集系统,逐事例的同时记录了自发裂变中子和瞬发伽马的飞行时间(TOF),脉冲形状甄别(PSD)和反冲能量(RE,裂变中子是通过测量反冲质子;瞬发伽马是通过测量康普顿反冲电子)三维信息.详细介绍了通过离线数据分析完全扣除三维信息中的伽马事例贡献,以获得Φ50.8 mm×50.8 mm的BC501A液闪探测器的相对探测效率和响应函数的方法.在不通过探测器响应函数进行数据转换的条件下,利用中子的能量直接确定了中子的有效测量阈值.得到的中子 关键词： 252Cf快裂变室')" href="#">²⁵²Cf快裂变室 BC501A液闪探测器 相对探测效率 响应函数     

Temperatures and Excitation Energies of Hot Nuclei in Reactions of 40Ar+natAg,209Bi at MeV/u

Coincidence measurements of fission fragment and light charged particle have been perfotrmed for the reactions of ⁴⁰Ar+^natAg,²⁰⁹Bi at E/A=25MeV using 4 PPAC and 11 sets of ΔE-E telescopes.Angular correlations of fission fragment were ploted as a function of the folding angle between the two detected fission fragments.The linear momentum transfer distributions were derived by measuring angular correlations.The backward spectra of light particles detected in coincidence with fission fragments having different average〈LMT〉are analyzed with Maxwell distribution.After some corrections the initial temperatures of the hot nuclei are determined from the energy spectra.The excitation energies corresponding to the different average〈LMT〉are obtained considering the reaction Q values and pre-equilibrum emission.In the central collision of the ⁴⁰Ar+^natAg,²⁰⁹Bi reactions,excitation energies are measured to be about 4.2MeV/u,2.4MeV/u and temperatures about 6.1MeV,5.5MeV,respecdvely.In semi-central collision,excitaionen energies are measured to be about 3.5MeV/u,1.9MeV/u and temperatures about 5.8MeV,4.8MeV respectively.     

Search for dynamical effects in the fission decay in the 240 MeV 32S + 100Mo reaction

Light particles in coincidence with evaporation residues and heavy fragments have been measured by a 4π charged-particle detector at the INFN Laboratori Nazionali di Legnaro (Padua) for the 240 MeV ³²S + ¹⁰⁰Mo reaction leading to the ¹³²Ce composite system at 152 MeV of excitation energy. Energy spectra of the alpha-particles in coincidence with fission fragments were extracted for many correlation angles both in plane and out of plane. A prominent out-of-plane emission was observed, consistent with the pattern for the near-scission emission. From the fit to the spectra, the pre-scission alpha-particle multiplicity of 0.040±0.006 was obtained. This value is reproduced by the code PACE2 without the inclusion of a delay time for fission. The presence of fast fission, which could be responsible for this result, is discussed. Received: 6 August 2002 / Accepted: 9 October 2002 / Published online: 4 February 2003 RID="a" ID="a"e-mail: moro@na.infn.it Communicated by C. Signorini     

Measurement of 248Cm/252Cf Cf Spontaneous Prompt Fission Neutron Spectrum

In order to treat the waste material of nuclear power and develop new type of clean nuclear power,it is necessary to measure the neutron adta of long half life nuclei existed in the waste material.The prompt spontaneous neutron spectrum is one of the most important unclear data for new type nuclear power facilities as well as for understanding the mechanism of fission neutron emission.The measurements of ²⁴⁸Cm/²⁵²Cf spontaneous prompt fission neutron spectrum in the neutron energy range form 200keV to 12MeV wer performed by using TOF method.A micro-ionization chamber aws used as fission fragment detector and stibene crystal as neutron detector.The flying paths of neutrons for the measurements were 30cm,50cm and 100cm respectively.The spontaneous prompt fission neutron spectrum of ²⁴⁸Cm was fitted by the Maxwellian distribution and the temperature was determined as (1.401±0.006)MeV in the corresponding neutron energy range.