Determination of aluminium and manganese in human scalp hair by electrothermal atomic absorption spectrometry using slurry sampling

Methods for the determination of aluminium and manganese in human scalp hair samples by electrothermal atomic absorption spectrometry using the slurry sampling technique were developed. Palladium and magnesium nitrate were used as chemical modifiers. Hair samples were pulverized using a zirconia vibrational mill ball, and were prepared as aqueous slurries. Determinations can be performed in the linear ranges of 1.9–150 μg l⁻¹ Al³⁺ and 0.03–10.0 μg l⁻¹ Mn²⁺. Limits of detection of 0.9 mg kg⁻¹ and 27.6 μg kg⁻¹ were obtained for aluminium and manganese, respectively. The analytical recoveries were between 99.6 and 101.8% for aluminium and in the 98.3–101.3% range for manganese. The repeatability of the methods (n=11), slurry preparation procedure and ETAAS measurement, was 16.0 and 7.9% for aluminium and manganese, respectively. The methods were finally applied to the aluminium and manganese determination in 25 scalp hair samples from healthy adults. The levels for aluminium were between 8.21 and 74.08 mg kg⁻¹, while concentrations between 0.03 and 1.20 mg kg⁻¹ were found for manganese.     

Determination of naringin in grapefruit juice by cathodic stripping differential pulse voltammetry at the hanging mercury drop electrode

A highly sensitive cathodic stripping voltammetric method for the determination of naringin is presented. It is based on the formation and accumulation of two naringin–mercury complexes at the electrode surface, followed by reduction of the surface species during a differential pulse voltammetric scan. The cathodic stripping responses at −0.25 V and −0.42 V, are evaluated with respect to various experimental conditions, such as composition and pH of the supporting electrolyte, naringin concentration, accumulation potential and preconcentration time. The new method is suitable for the determination of naringin concentrations between 0.1 mg l⁻¹ (1.72×10⁻⁷ mol l⁻¹) and 40 mg l⁻¹ (6.88×10⁻⁵ mol l⁻¹). A 3σ limit of detection of 32 μg l⁻¹ (55 nmol l⁻¹) can be reached. The relative standard deviation (r.s.d.) is <1.5%. Recovery experiments yielded a mean recovery of 97% (r.s.d.=4.1%). The application of the procedure to the selective determination of naringin in grapefruit juice is demonstrated.     

Methods for separation of trace amounts of platinum and investigation of the influence of interfering elements during platinum determination in copper ores and copper concentrates by graphite furnace atomic absorption spectrometry

A THGA graphite furnace with Zeeman background correction has been used to determine platinum content in copper ore and copper concentrate at the part per billion (ppb) concentration level. Two different procedures for the separation of trace platinum have been applied: (i) use of an ion exchange resin; and (ii) a two-stage method based on platinum separation on inorganic carriers. The influence of interfering elements in the matrix (Cu, Pb, Fe, Ti, V, Au, Pd, Ir, Rh and Al) has been examined using a graphite furnace. It was found that the presence of Cu (12.5–100 mg l⁻¹), Pb (100–500 mg l⁻¹), Fe (100–2000 mg l⁻¹), Ti (25–100 mg l⁻¹), V (25–100 mg l⁻¹), Au (25–300 mg l⁻¹), Pd (20–250 mg l⁻¹), Ir (0.5–3.5 mg l⁻¹) and Rh (0.025–1 mg l⁻¹) in the samples analyzed has no effect on the platinum absorption signal when using a recommended temperature program (T_pyr=1300°C, T_at=2450°C). Spectral interference was observed, which was due to aluminum, as a result of the close neighborhood of the Pt 265.945-nm and Al 266.039-nm lines. This interference could not be eliminated by the Zeeman background correction.     

Determination of ammonia in beers by pervaporation flow injection analysis and spectrophotometric detection

A pervaporation flow injection (PFI) method is described for the determination of ammonia in beers. After injecting the sample into a NaOH donor solution, ammonia and other volatiles are transferred in the pervaporation unit from the donor stream to an acceptor stream containing sodium salicylate and nitroprusside, which subsequently mixes with alkaline sodium dichloroisocyanurate to allow the classical Berthelot reaction to take place. The blue-coloured complex formed is monitored spectrophotometrically at 655 nm. A linear calibration curve with a range of 0.1–40 mg l⁻¹ was obtained. The method has a detection limit of 0.05 mg l⁻¹ and is capable of a sampling frequency of 11 h⁻¹ at 4 mg l⁻¹ ammonia. It was applied successfully to the determination of ammonia in synthetic samples and unfiltered lager beers. The advantages of the present method over the ammonia ion-selective electrode method and the PFI system based on mixed indicator detection are discussed.     

Determination of nanomolar concentrations of phosphate in freshwaters using flow injection with luminol chemiluminescence detection

A simple and rapid flow injection (FI) method is reported for the determination of phosphate (as molybdate reactive P) in freshwaters based on luminol chemiluminescence (CL) detection. The molybdophosphoric heteropoly acid formed by phosphate and ammonium molybdate in acidic conditions generated chemiluminescence emission via the oxidation of luminol. The detection limit (3× standard deviation of blank) was 0.03 μg P l⁻¹ (1.0 nM), with a sample throughput of 180 h⁻¹. The calibration graph was linear over the range 0.032–3.26 μg P l⁻¹ (r²=0.9880) with relative standard deviations (n=4) in the range 1.2–4.7%. Interfering cations (Ca(II), Mg(II), Ni(II), Zn(II), Cu(II), Co(II), Fe(II) and Fe(III)) were removed by passing the sample through an in-line iminodiacetate chelating column. Silicate interference (at 5 mg Si l⁻¹) was effectively masked by the addition of tartaric acid and other common anions (Cl⁻, SO₄²⁻, HCO₃⁻, NO₃⁻ and NO₂⁻) did not interfere at their maximum admissible concentrations in freshwaters. The method was applied to freshwater samples and the results (26.1±1.1–62.0±0.4 μg P l⁻¹) were not significantly different (P=0.05) from results obtained using a segmented flow analyser method with spectrophotometric detection (24.4±4.45–84.0±16.0 μg P l⁻¹).     

Use of silica gel chemically modified with zirconium phosphate for preconcentration and determination of lead and copper by flame atomic absorption spectrometry

An analytical method using silica gel chemically modified with zirconium (IV) phosphate for preconcentration of lead and copper, in a column system, and their sequential determination by flame atomic absorption spectrometry (FAAS), was developed. Sample solutions are passed through a glass column packed with 100 mg of the sorbent material, at pH 4.5, and lead and copper are eluted with 1.0 mol l⁻¹ HNO₃ at a flow rate of 2.0 ml min⁻¹. The extraction of copper is affected by Fe(II), Mn(II), Zn(II), Ni(II) and Co(II) while only Fe(II) interferes in the lead determination. These interferences may be overcome with an appropriate addition of a KI or NaF solution. An enrichment factor of 30 was obtained for both metals. While the limits of detection (3σ) were 6.1 and 1.1 μg l⁻¹, for Pb and Cu, respectively, the limits of determination were 16.7 and 3.3 μg l⁻¹. The precision expressed as relative standard deviation (R.S.D.) obtained for 3.3 μg l⁻¹ of Cu and 16.7 μg l⁻¹ of Pb were 4.3 and 4.7%, respectively, calculated from ten measurements. The proposed method was evaluated with reference material and was applied for the determination of lead and copper in industrial and river waters.     

Copper determination in natural water samples by using FAAS after preconcentration onto amberlite XAD-2 loaded with calmagite

A procedure for separation and preconcentration of trace amounts of copper in natural water samples, has been proposed. It is based on the adsorption of copper(II) ions onto a column of Amberlite XAD-2 resin loaded with calmagite reagent. This way amounts of copper within the range from 0.0125 to 25.0 μg, in a sample volume of 25 to 250 ml, and pH from 3.7 to 10.0 was concentrated as calmagite complex in a column of 0.50 g of Amberlite XAD-2 resin. Copper (II) ion was desorpted by using 5.0 ml of 2 mol l⁻¹ hydrochloric acid. Detection and determination limits of the proposed procedure for 250 ml sample volume were 0.15 and 0.50 μg l⁻¹, respectively. Selectivity test showed that (in the indicated concentration), calcium(II) (500 mg l⁻¹), magnesium(II) (500 mg l⁻¹), strontium(II) (50 mg l⁻¹), iron(III) (10 mg l⁻¹), nickel(II) (10 mg l⁻¹), cobalt(II) (10 mg l⁻¹), cadmium(II) (10 mg l⁻¹) and lead(II) (10 mg l⁻¹) did not interfere in copper determination by this procedure. Precision of the method, evaluated as the relative standard deviation by analyzing a series of seven replicates, was 2.42% for a copper mass of 1.0 μg in a sample volume of 100 ml. The accuracy of the proposed procedure was evaluated by means of copper determination in reference biological samples. The achieved results were in good agreement with certified values. The extractor system had a sorption capacity of 1.59 μmol of copper per gram of resin loaded with calmagite. The proposed procedure was applied for copper determination by FAAS in natural water samples. Samples were collected from different places of Salvador city, Bahia, Brazil. The achieved recovery, measured by the standard addition technique, showed that the proposed procedure had good accuracy. A good enrichment factor (50×) and simplicity are the main advantages in this analytical procedure.     

Determination of selenium, zinc and cadmium in antidandruff shampoos by atomic spectrometry after microwave assisted sample digestion

Microwave assisted pre-treatments for atomic spectrometric determination (inductive coupled plasma-optical emission spectrometry, ICP-OES or flame atomic absorption spectrometry, FAAS) of metallic elements, usually present in antidandruff shampoos, are proposed. They are based on the digestion of the sample with HNO₃ into a closed reactor, which is irradiated at 800 W for a few minutes. Selenium was determined by ICP-OES. The limit of detection was 0.11 mg l⁻¹; the relative standard deviation (R.S.D.) for the selenium content in the samples was in the 0.6–3.6% range. The results obtained were in agreement with the label contents and the recovery of the proposed method was in the 100–106% range. Zinc and cadmium were determined by FAAS. The limit of detection for zinc determination was 0.078 mg l⁻¹; the R.S.D. for zinc contents was in the 0.8–8.6% range. A limit of detection of 0.09 mg l⁻¹ was obtained for cadmium determination; the R.S.D. for cadmium contents was in the 0.7–2.7% range. The determinations were performed after two different sample mineralization pre-treatments — dry ashing (in an electric furnace) and wet mineralization (in a microwave oven). Both methodologies provided comparable results for zinc and cadmium determination in shampoos. The proposed microwave assisted digestion procedures allow a precise and accurate determination of selenium, zinc and cadmium in commercial antidandruff shampoos, and the sample pre-treatment is less time-consuming than the classic methods.     

Determination of physiological noble metals in human urine using liquid-liquid extraction and Zeeman electrothermal atomic absorption spectrometry

An extremely sensitive, reliable and simple procedure is described for the determination of physiological palladium, platinum and gold in human urine. The urine samples were adjusted to pH 4 (Pd, Au) or pH 5 (Pt), followed by conversion of the analytes to their pyrrolidinedithiocarbamate complexes. These complexes were separated from the matrix by liquid-liquid extraction into 4-methyl-2-pentanone resulting in a 25-fold enrichment. Determination was by electrothermal atomic absorption spectrometry (ET-AAS) using longitudinal inverse alternating current Zeeman-effect background correction. The limits of detection calculated from three standard deviations of the blank values were 20 ng l⁻¹ for Pd and Au and 70 ng l⁻¹ Pt. Within-day precision (n = 10, 5 μg l⁻¹) ranged 5.2%–7.7%. The procedure is successfully applied to determine urinary palladium, platinum and gold in nine unexposed persons. Palladium levels in urine ranged < 20–80 ng l⁻¹ (arithmetical MEAN=38.7 ng l⁻¹), while gold levels ranged < 20–130 ng l⁻¹ (36.0 ng l⁻¹). Physiological platinum levels in urine were all < 70 ng l⁻¹. The accuracy of the procedure was checked by analyzing a series of urine samples by a second independent method (magnetic sector field inductively-coupled plasma-mass spectrometry) in combination with UV photolysis.     

Determination of bisphenol A (BPA) in the presence of phenol by first-derivative fluorescence following micro liquid-liquid extraction (MLLE)

Bisphenol A (BPA) in the presence of phenol is determined using a method based on first-derivative spectrofluorimetry. The proposed method involves a micro liquid–liquid extraction of sodium chloride saturated water samples with diethyl ether followed by direct fluorimetric analysis of extracts. The excitation spectra of both compounds in diethyl ether are recorded between 200 and 290 nm, with the emission wavelength at 306 nm. The first-derivative spectra were calculated, measuring the analytical signal for BPA at 239 nm. The concentration range over which the method was applied was 0.5–10.0 μg·l⁻¹ of BPA with relative standard deviations of 2.9% for a concentration of 4.0 μg·l⁻¹ of BPA. The detection limit was 0.07 μg·l⁻¹. The proposed method was applied satisfactorily to the determination of BPA in synthetic mixtures and water samples from different sources previously spiked with different amounts of these chemicals. Recovery values ranging from 93% to 112% were obtained for water samples.     

Simultaneous flow injection determination of calcium and fluoride in natural and borehole water with conventional ion-selective electrodes in series

An on-line automated system for the simultaneous flow injection determination of calcium and fluoride in natural and borehole water with conventional calcium-selective and fluoride-selective membrane electrodes as sensors in series is described. Samples (30 μl) are injected into a TISAB II (pH=5.50) carrier solution as an ionic strength adjustment buffer. The sample-buffer zone formed is first channeled to a fluoride-selective membrane electrode and then via the calcium-selective membrane electrode to the reference electrodes. The system is suitable for the simultaneous on-site monitoring of calcium (linear range 10⁻⁵–10⁻² mol l⁻¹ detection limit 1.94×10⁻⁶ mol l⁻¹ recovery 99.22%, RSD<0.5%) and fluoride (linear range 10⁻⁵–10⁻² mol l⁻¹ detection limit 4.83×10⁻⁶ mol l⁻¹ recovery 98.63%, RSD=0.3%) at a sampling rate of 60 samples h⁻¹.     

Spectrophotometric determination of trace amounts of cobalt with 2-hydroxybenzaldehyde-5-nitro-pyridylhydrazone in presence of surfactant after separation with Amberlite IRC-718 resin

2-Hydroxybenzaldehyde-5-nitro-pyridylhydrazone (2HB-5NPH) was synthesized and its application in the spectrophotometric determination of metal ions was studied in the presence of surfactants. A separation procedure, using a short column filled with Amberlite IRC 718, is proposed for the spectrophotometric determination of traces of cobalt. The influence of several ions, as interference, was discussed. The procedure was applied to determination of cobalt in mixture sample with satisfactory results (≥recovery 96%; relative error ≤2%; relative standard deviation ≤1.2% in the concentration range of 0.02–2.0 mg l⁻¹; detection limit, 0.01 mg l⁻¹ in solution). Control of the pH during the column operation is essential because the adsorption capacities are very sensitive to change in pH. Their separation was carried out in 0.005 M Malic acid, 1.5 M HCl, 2.0 M HNO₃ media.     

Design of a composite amperometric enzyme electrode for the control of the benzoic acid content in food

A graphite–Teflon–tyrosinase composite biosensor for the determination of benzoic acid in foodstuffs is reported. The biosensor functioning is based on the inhibition effect of benzoic acid on the biocatalytic activity of the enzyme in a reversed micelle working medium formed with ethyl acetate as the continuous phase, a 0.05 mol l⁻¹ phosphate buffer solution of pH 7.4 (5%) as the aqueous dispersed phase, and 0.10 mol l⁻¹ dioctyl sulfosuccinate (AOT) as the emulsifying agent. A potential value of −0.10 V, and a constant enzyme-substrate (phenol) concentration of 2.0×10⁻⁴ mol l⁻¹ were selected to carry out the amperometric inhibition measurements. The tyrosinase inhibition process by benzoic acid is reversible and of the competitive type, with an apparent inhibition constant of 0.016 mmol l⁻¹. The composite bioelectrodes allow the regeneration of the electrode surface by polishing and exhibit long-term operation and stability. A limit of detection of 9.0×10⁻⁷ mol l⁻¹ benzoic acid was obtained. An interference study from other substances which can be found in foodstuffs together with benzoic acid was performed. Taking advantage of the capabilities of reversed micelles as universal solubilization media, the composite tyrosinase electrode was used for the determination of benzoic acid in two different kind of samples: mayonnaise sauce, which is a highly hydrophobic matrix, and Cola soft drinks, a hydrophilic matrix for which practically no sample treatment is necessary.     

Continuous flow system for lead determination by faas in spirituous beverages with solid phase extraction and on-line copper removal

A continuous flow system for the determination of lead in home made spirituous beverages was developed. The determination was based on the formation of a neutral chelate of the element with ammonium pyrrolidine dithiocarbamate, its adsorption onto a minicolumn packed with sodium faujasite type Y synthetic zeolite, followed by elution with methyl isobutyl ketone and determination by flame atomic absorption spectrometry. Ethanol and copper interfere strongly in the determination and therefore, must be separated prior to the analysis. Copper is removed by precipitation with rubeanic acid, while ethanol is eliminated by rotaevaporation. Sample solutions containing Pb²⁺ in the concentration range from 5 to 120 μg l⁻¹ at pH 2.5 could be analyzed, by using a preconcentration time of 3 min. Preconcentration factors from 80 to 140 were achieved for a sample volume of 6 ml and the detection limit varied from 1.4 to 3.5 μg l⁻¹, depending on the matrix composition. The relative standard deviations for 60 μg l⁻¹ Pb was 3.2% (n = 10) and the recovery of spikes (20, 40, 60 and 80 μg l⁻¹) added to the samples was estimated within 92–105% range, suggesting that lead can be quantitatively determined in such samples. Determining lead in several samples by an alternative technique further checked the accuracy. Finally, the concentrations of Pb²⁺ determined in 28 samples of Venezuelan spirituous beverages were in 12.6–370.0 μg l⁻¹ range, depending on the fermenting material based on different mixtures of agave, raw sugar cane and white sugar.     

Flow injection for the determination of Se(IV) and Se(VI) by hydride generation atomic absorption spectrometry with microwave oven on-line prereduction of Se(VI) to Se(IV)

An on-line flow injection system has been developed for the selective determination of Se(IV) and Se(VI) in citric fruit juices and geothermal waters by hydride generation atomic absorption spectrometry with microwave-aided heating prereduction of Se(VI) to Se(IV). The samples and the prereductant solutions (4 mol l⁻¹ HCl for Se(IV) and 12 mol l⁻¹ HCl for Se(VI)) which circulated in a closed-flow circuit were injected by means of a time-based injector. This mixture was displaced by a carrier solution of 1% v/v of hydrochloric acid through a PTFE coil located inside the focused microwave oven and mixed downstream with a borohydride solution to generate the hydride. The linear ranges were 0–120 and 0–100 μg l⁻¹ of Se(IV) and Se(VI), respectively. The detection limits were 1.0 μg l⁻¹ for Se(IV) and 1.5 μg l⁻¹ for Se(VI). The precision (about 2.0–2.5% RSD) and recoveries (96–98% for Se(IV) and 94–98% for Se(VI)) were good. Total selenium values were also obtained by electrothermal atomic absorption spectrometry which agreed with the content of both selenium species. The sample throughput was about 50 measurements per hour. The main advantage of the method is that the selective determination of Se(IV) and Se(VI) in citric fruit juices and geothermal waters is performed in a closed system with a minimum sample manipulation, exposure to the environment, minimum sample waste and operator attention.     

Voltammetric determination of phytochelatins using copper solid amalgam electrode

Voltammetric determination of synthetically prepared phytochelatins (γ-Glu-Cys)₂Gly (PC₂) and (γ-Glu-Cys)₃Gly (PC₃) has been studied using new type of copper solid amalgam electrode. The determination, based on the formation of cuprous complexes in buffer pH 8.1, is suitable for concentrations of PC in the range 10–100 nmol l⁻¹. Reproducibility, employing electrochemical cleaning of the electrode surface, was statistically evaluated. The achieved limit of detection (2.1–2.6×10⁻⁹ mol l⁻¹ for DCV measurement) together with the robust character of the electrode offer its use for detection of PCs in separated extracts of real samples.     

Speciation of chromium in mineral waters and salinas by solid-phase extraction and graphite furnace atomic absorption spectrometry

A simple GF-AAS method for speciation analysis of chromium in mineral waters and salinas was developed. Cr(VI) species were separated from Cr(III) by solid-phase extraction with APDC (ammonium pyrrolidinedithiocarbamate). The APDC complexes were formed in the sample solution under proper conditions, adsorbed on Diaion HP-2MG resin and the resin was separated from the sample. After elution with concentrated nitric acid Cr(VI) was determined by GF-AAS. Total chromium was determined by GF-AAS directly in the sample and Cr(III) concentration was calculated as the difference between those results.

The detection limit of the method defined as 3 s of background variation was 0.03 μg l⁻¹ for Cr(VI) and 0.3 μg l⁻¹ for total chromium. RSD for Cr(VI) determination at the concentration of 0.14 μg l⁻¹ was 9%, and for total chromium at the concentration of 5.6 μg l⁻¹ was 5%. The recovery of Cr(VI) was in the range of 94–100%, dependently on type of the sample.

The investigation of recovery of the spiked Cr(VI) showed that at concentration levels near 1 μg l⁻¹ and lower recovery may be reduced significantly even by pure reagents that seem to be free from any reductants.     

Determination of tannic acid by direct chemiluminescence in a FIA assembly

The determination of tannic acid is performed in a FIA assembly on the basis of the analytical output obtained by oxidation of the acid. The analyte solution was daily prepared in a mixture of quinine as sensitiser and perchloric acid and it was injected into a pure water stream acting as a carrier. This solution merges with the mixture potassium permanganate in perchloric medium and the resulting chemiluminescence is monitored. The method was applied over the range 0.5–20 mg l⁻¹ of tannic acid with a LOD 100 μg l⁻¹. The reproducibility was 2.1% and the sample throughput 54 h⁻¹. The influence of foreign substances was studied and the new method is applied to the determination of tannic acid in pharmaceutical and galenic formulations in human urine and surface waters.     

Determination of chlorite in drinking water by on-line coupling of capillary isotachophoresis and capillary zone electrophoresis

An isotachophoresis (ITP)–capillary zone electrophoresis (CZE) combination was used for the determination of chlorite in drinking waters. No sample preparation is needed and no interfering by other anions in tap water was observed. The reached limits of detection with conductivity detector were 0.012–0.017 mg l⁻¹. By four-fold sample loading with a 30 μl valve, 0.005 mg l⁻¹ of chlorite was determined with R.S.D.=3.3%. The concentrations of 0.05 and 0.20 mg l⁻¹ were measured with R.S.D. of 2.2 and 2.7%, respectively. The recoveries of chlorite from drinking water were 96–106% in the range of 0.02–0.20 mg l⁻¹. The R.S.D. values of migration times (inter-day) were up to 1.3%. The time for analysis is about 15 min.     

Analytical method for the determination of the aminoglycoside gentamicin in hospital wastewater via liquid chromatography-electrospray-tandem mass spectrometry

A method for the determination of gentamicin residues in hospital wastewater has been developed using kanamycin as a surrogate standard. The method consists of solid-phase extraction (SPE) and detection by ion-pair chromatography with electrospray tandem mass spectrometry (LC–ES-tandem MS). The SPE was performed on a weak cation exchanger. Filtration should be avoided in the sample preparation, otherwise a significant loss of gentamicin occurs. Chromatographic separation on a C₁₈-column was achieved using a ternary eluent containing methanol, water and 20 mmol l⁻¹ heptafluorobutyric acid solution. Mean relative recoveries of the analytes in hospital wastewater varied between 107 and 111%. The limit of quantification (LOQ) was 0.20 μg l⁻¹ in hospital wastewater. Gentamicin was found in native hospital wastewater in a concentration range between 0.4 and 7.6 μg l⁻¹.