Application of headspace solid phase microextraction and gas chromatography to the screening of volatile compounds from some Brazilian aromatic plants

Summary An HS-SPME method was developed and applied for the isolation of volatile organic compounds from plants native or acclimatized to Brazil. Method optimization was performed using typical analytes from the target samples; fibers coated with 100 μm PDMS and 75 μm Carboxen/PDMS were tested. Using PDMS 100 μm fibers and GC-MS for separation and identification, up to 99.9% of the peak area in the chromatograms from plants were identified. The method was also applied to quantify the major volatile components of one of the samples (Aloysia gratissima) with results comparable to those from the conventional steam distillation method.     

顶空固相微萃取-气相色谱-质谱联用分析纺织品中挥发性有机物

建立了顶空固相微萃取（HSSPME）-气相色谱（GC）-质谱（MS）联用测定纺织品中甲苯、4-乙烯基环己烯、苯乙烯、萘和1-苯基环己烯5种挥发性有机物（VOCs）的分析方法。选择聚二甲基硅氧烷（PDMS）作为萃取涂层,优化了SPME的萃取条件,包括平衡时间、萃取时间、萃取温度、顶空体积、离子强度、搅拌速度、解吸温度和时间以及GC—MS仪器条件。对于甲苯、4-乙烯基环己烯、苯乙烯、萘和1-苯基环己烯方法线性范围分别为0．087～870、3．32～3320、2．28～2280、0．015～150和0．050～50．0ng／g;检出限分别为0．005、0．042、0．670、0．008和0．011ng／g。实际样品加标回收率在80．1％～122％之间,RSD在0．8％～8．6％之间。方法符合纺织品中痕量VOCs的快速分析要求。     

Sampling volatile organic compounds using a modified solid phase microextraction device

Headspace solid phase microextraction (headspace SPME) has been demonstrated to be an excellent solvent-free sampling method. One of the major factors contributing to the success of headspace SPME is the concentrating effect of the fiber coating toward organic compounds. The affinity of the fiber coating toward very volatile analytes, such as chloromethane, may, however, not be large enough for detection at the parts per trillion concentration level. Static headspace analysis, on the other hand, is very effective for these very volatile compounds. As analyte volatility decreases, the sensitivity of static headspace analysis drops. The complementary nature of these two sampling methods can be exploited by combining the SPME device with a gastight syringe. The sensitivity of the new sampling device is better than that of SPME for very volatile compounds or that of static headspace analysis for less volatile compounds. This new method can sample a wide range of compounds from chloromethane (b.p. −24°C) to bromoform (b.p. 149°C) with estimated limits of detection at the low parts per trillion level.     

Solid phase microextraction of volatile organic compounds using carboxen-polydimethylsiloxane fibers

Summary A new 80 μm Carboxen-polydimethylsiloxane (PDMS) fiber for solid phase microextraction (SPME) was tested for the enrichment of volatile organic compounds from water and air. Detection limits between 13 ng L⁻¹ (CH₂Cl₂) and 0.1 ng L⁻¹ (CHCl₂Br and CHClBr₂) for the combination: Carboxen-PDMS fiber and GC-ECD and between 35 ng L⁻¹ and 45 ng L⁻¹ (BTEX compounds) for the combination: Carboxen-PDMS and GC-FID using the headspace procedure were determined. Comparisons with the 100 μm PDMS fiber and further coatings show the advantages of the Carboxen-PDMS fiber with respect to extraction efficiency. Disadvantages of the new fiber compared with the 100 μm PDMS fiber are poorer repeatability and prolongation of equilibrium time. Distribution coefficients of the BTEX compounds between aqueous solution and SPME fiber coating were calculated and compared with the results of other researchers and with octanol-water partition coefficients.     

Analysis of organic compounds in environmental samples by headspace solid phase microextraction

The analysis of samples contaminated by organic compounds is an important aspect of environmental monitoring. Because of the complex nature of these samples, isolating target organic compounds from their matrices is a major challenge. A new isolation technique, solid phase microextraction, or SPME, has recently been developed in our laboratory. This technique combines the extraction and concentration processes into one step; a fused silica fiber coated with a polymer is used to extract analytes and transfer them into a GC injector for thermal desorption and analysis. It is simple, rapid, inexpensive, completely solvent-free, and easily automated. To minimize matrix interferences in environmental samples, SPME can be used to extract analytes from the headspace above the sample. The combination of headspace sampling with SPME separates volatile and semi-volatile analytes from non-volatile compounds, thus greatly reducing the interferences from non-target compounds. This paper reports the use of headspace SPME to isolate volatile organic compounds from various matrices such as water, sand, clay, and sludge. By use of the technique, benzene, toluene, ethyl-benzene, and xylene isomers (commonly known as BTEX), and volatile chlorinated compounds can be efficiently isolated from various matrices with good precision and low limits of detection. This study has found that the sensitivity of the method can be greatly improved by the addition of salt to water samples, water to soil samples, or by heating. Headspace SPME can also be used to sample semi-volatile compounds, such as PAHs, from complex matrices.     

Analysis of monoterpenes from conifer needles using solid phase microextraction

The applicability of solid phase microextraction (SPME) to the headspace analysis of monoterpene hydrocarbons from conifer needles was examined. To this end, the influences of fiber coating thickness, exposure time, and exposure temperature on the enrichment of the different monoterpene hydrocarbons were investigated. The distribution constants between polydimethylsiloxane fiber and gas phase at a given temperature were found to be very different. A relation is therefore derived to calculate the distribution constants of substances not available from their Kováts retention indices. A slightly different approach could be the use of so-called “relative distribution factors”, not considering the actual volume of fiber coating. In view of the different enrichment conditions in SPME as well as the general problems of headspace analysis, a comparison with a completely different method of sample preparation is presented. Furthermore, some applications of SPME to the analysis of monoterpenes from pine needles are given.     

Polyaniline-polypyrrole coating for solid phase microextraction

A procedure for direct electrochemical deposition of polyaniline-polypyrrole blend coating on the surface of stainless steel wire was suggested. Incorporation of polyaniline and polypyrrole into the blend coating was confirmed by infrared spectroscopy. Key parameters (pyrrole, aniline, dopant and sulphuric acid concentrations and deposition potential) influencing the coating’s mechanical stability and surface homogeneity were optimised and thermostability of the coating was investigated. A possibility to apply the coating as a new fibre for solid phase microextraction was demonstrated. The coating showed better selectivity toward aromatic, hydrophobic compounds.      

Determination of tobacco alkaloids using solid phase microextraction and GC-NPD

Summary The sampling approaches using solid phase microextraction (SPME) were evaluated for the analysis of tobacco alkaloids. Because of their low volatility and ionic nature, sampling alkaloids from the headspace of dry or wet tobacco samples often required more effort to improve extraction efficiency. Directly dipping the SPME fiber coated with polydimethylsiloxane film into the tobacco extract was proved to be a simple, effective tool for sampling alkaloids from tobacco. When combined with the practice of fast GC and nitrogen-phosphorus detection, nicotine and a group of selected minor alkaloids (i.e., nornicotines, myosmine, anabasine and anatabine) were separated with baseline resolution within 3 min. The detection limits for these alkaloids are below 0.1 μg mL⁻¹. In addition, the carry-over problem frequently occurred in alkaloids analysis was eliminated. The influence of tobacco matrix and fiber aging on the partition of alkaloids, as well as the use of an internal standard to compensate these deviations, were also studied.     

Determination of volatile fatty acid ethyl esters in raw spirits using solid phase microextraction and gas chromatography

An analytical method for the determination of fatty acid ethyl esters in raw spirits of different quality or produced from various raw materials has been developed and optimized. A combination of headspace solid phase microextraction (HS-SPME) as the extraction technique and gas chromatography with flame ionization detection (GC-FID) as the determination technique was utilized. HS-SPME conditions such as: type of the stationary phase of the fiber, ethanol content, sample volume, extraction temperature and time, salt addition and sample agitation were investigated to determine the most suitable conditions for the analysis of volatile fatty acid ethyl esters in raw spirits. The quantification method was an internal standardization using methyl octanoate as the internal standard. The method's detection limits (MDLs) for the individual ethyl esters ranged from 26.8 to 0.0470 μg L⁻¹ 20% EtOH. The feasibility of SPME for the quantitative analysis of fatty acid ethyl esters in raw spirits of different organoleptic quality was demonstrated. High precision and simple sample preparation enable the use of this method for routine investigations in both industrial and research laboratories.     

Potential sources of background contaminants in solid phase extraction and microextraction

A study to identify the sources of background contamination from SPE, using a C-18 sorbent, and solid-phase microextraction (SPME), using a 70 microm carbowax/divinylbenzene (CW/DVB) fiber, was carried out. To determine the source of contamination, each material used in the procedure was isolated and examined for their contribution. The solid-phase column components examined were: sorbent material and frits, column housings and each solvent used to elute analytes off the column. The components examined in the SPME procedure were: SPME fiber, SPME vials, water (HPLC grade), and salt (sodium chloride) used to increase the ionic strength. The majority of the background contaminants from SPE were found to be from the SPE sorbent material and frits. The class of contaminants extracted during a blank extraction were phthalates and other plasticizers used during the manufacturing process. All had blank levels corresponding to measured concentrations below 2 ng/ mL, except for undecane, which had a concentration of 5.4 ng/mL. The most prevalent contaminants in the SPME blank procedure are 1,9-nonanediol, a mixture of phthalates and highly bis-substituted phenols. All the concentrations were below 2 ng/mL, with the exception of bis (2-ethylhexyl) phthalate, which had concentrations ranging from 5 to 20 ng/mL.     

茶叶中三氯杀螨醇残留量的微波萃取-固相微萃取-气相色谱快速检测方法

建立了微波辅助萃取-固相微萃取-气相色谱/电子捕获检测法快速测定茶叶中三氯杀螨醇的方法。采用自制的PDMS萃取头,优化了萃取溶剂的种类,微波辐射时间和微波功率等微波辅助萃取条件;研究了SPME萃取时间、搅拌速度、离子强度、解吸温度和解吸时间对萃取效率的影响。方法对三氯杀螨醇的检出限为0.048 ng/mL,线性范围为0.2~200 ng/mL。在优化的实验条件下,对乌龙茶进行添加回收试验,平均回收率为61.3%~72.8%,相对标准偏差为8.0%~16.3%。本方法适合于茶叶中痕量三氯杀螨醇快速检测。     

Determination of triazines and amides in water using solid phase microextraction coupled with GC-MS

Summary Solid phase microextraction was coupled with gas chromatography-mass spectrometry (SPME-GC-MS) to screen for sixteen nitrogen-containing compounds, including herbicides, in water samples. The effects of stirring, extraction time, pH, salt concentration and the choice of fiber coating material were evaluated. The repeatability was in the range of 0.72–18.2 (CV % at 200 ng·L⁻¹) and the reproducibility, in the range of 5.4–34 (at 500 ng·L⁻¹).     

The determination of volatile organic compounds in soils using solid phase microextraction with gas chromatography-mass spectrometry

Solid phase microextraction (SPME) was applied in the development of a protocol for the analysis of a number of target organic compounds in landfill site samples. The selected analytes, including aromatic hydrocarbons, chlorinated hydrocarbous, and unsaturated compounds, were absorbed directly from a headspace sample above a soil layer onto a fused silica fiber. Following exposure, the fiber was thermally desorbed in the injection port of the gas chromatograph and eluted compounds were detected using a mass selective detector. The stability and sensitivity of the extraction technique were examined at five temperatures (22–60°C) using a 100μm polydimethylsiloxane fiber. Calibrations, using soil samples spiked with selected solvents (0.5–30 μg/g), were linear; trichloroethene (r² = 0.992) and benzene (r² = 0.998). SPME was applied to the examination of a municipal landfill where 8 sites were sampled, at three depths, resulting in the detection of xylene (maximum 2.8 μg/g) and a number of other non-target organic contaminants.     

溶胶-凝胶固相微萃取涂层及其在农药残留分析中的应用

利用溶胶-凝胶(sol-gel)技术制备固相微萃取(SPME)涂层材料.通过硅醇盐前驱体与涂层聚合物羟基硅油(OH-TSO)的水解共聚的方法,成功地制备了聚二甲基硅氧烷sol-gel 涂层的SPME 萃取头,并以农药的混合标准水溶液为研究对象,用直接-固相微萃取-气相色谱法(GC)对涂层的性能进行考察,制成的萃取头适用于多种农药残留的萃取分离分析.     

The use of headspace solid phase microextraction for the characterization of volatile compounds in olive oil matrices

Two different fibre coatings, for solid phase microextraction (SPME) sampling, poly(dimethylsiloxane) (PDMS) and poly(acrylate) (PA), were studied in order to test, for olive oil matrixes, two mathematical models that relate the directly proportional relationship between the amount of analyte absorbed by a SPME fibre and its initial concentration in the sample matrices. Although the PA fibre was able to absorb higher amounts of compounds from the olive oil sample, the equilibrium was reached later then with the PDMS fibre. In both cases, the amount of analyte present affected the time profile or the equilibrium time in two of the concentrations studied, 0.256 μL/kg, 2.56 μL/kg and for 2-ethylfuran, pentan-3-one, pent-1-en-3-one, hexanal, trans,trans-non-2,4-dienal and in the four concentrations studied, 0.256 μL/kg, 2.56 μL/kg, 6.25 μL/kg and 400 μL/kg, for 4-methyl-pent-3-en-2-one, 2-methylbutan-1-ol, methoxybenzene, hexan-1-ol, cis-hex-3-en-1-ol, trans-hex-2-en-1-ol, 2-ethyl-hexan-1-ol and trans,trans-dec-2,4-dienal. Comparing the mathematical models of both fibres, the PA-coated fibre showed direct proportionality between the initial concentration and amount extracted, that allows the possibility of relative quantification in a non-equilibrium state in non-aqueous media. The same was not observed for the PDMS fibre.     

Layered double hydroxide/poly(vinylpyrrolidone) coated solid phase microextraction Arrow for the determination of volatile organic compounds in water

Today, wide variety of adsorbents have been developed for sample pretreatment to concentrate and separate harmful substances. However, only a few solid phase microextraction Arrow adsorbents are commercially available. In this study, we developed a new solid phase microextraction Arrow coating, in which nanosheets layered double hydroxides and poly(vinylpyrrolidone) were utilized as the extraction phase and poly(vinyl chloride) as the adhesive. This new coating entailed higher extraction capacity for several volatile organic compounds (allyl methyl sulfide, methyl propyl sulfide, 3‐pentanone, 2‐butanone, and methyl isobutyl ketone) compared to the commercial Carboxen 1000/polydimethylsiloxane coating. Fabrication parameters for the coating were optimized and extraction and desorption conditions were investigated. The validation of the new solid phase microextraction Arrow coating was accomplished using water sample spiked with volatile organic compounds. Under the optimal conditions, the limits of quantification for the five volatile organic compounds by the new solid phase microextraction Arrow coating and developed gas chromatography with mass spectrometry method were in the range of 0.2‐4.6 ng/mL. The proposed method was briefly applied for enrichment of volatile organic compounds in sludge.     

Analysis of the volatile chemical markers of explosives using novel solid phase microextraction coupled to ion mobility spectrometry

Ion mobility spectrometry (IMS) is routinely used in screening checkpoints for the detection of explosives and illicit drugs but it mainly relies on the capture of particles on a swab surface for the detection. Solid phase microextraction (SPME) has been coupled to IMS for the preconcentration of explosives and their volatile chemical markers and, although it has improved the LODs over a standalone IMS, it is limited to sampling in small vessels by the fiber geometry. Novel planar geometry SPME devices coated with PDMS and sol-gel PDMS that do not require an additional interface to IMS are now reported for the first time. The explosive, 2,4,6-trinitrotoluene (TNT), is sampled with the planar SPME reaching extraction equilibrium faster than with fiber SPME, concentrating detectable levels of TNT in a matter of minutes. The surface area, capacity, extraction efficiency, and LODs are also improved over fiber SPME allowing for sampling in larger volumes. The volatile chemical markers, 2,4-dinitrotoluene, cyclohexanone, and the taggant 4-nitrotoluene have also been successfully extracted by planar SPME and detected by IMS at mass loadings below 1 ng of extracted analyte on the planar device for TNT, for example.     

Investigation of the kinetic process of solid phase microextraction in complex sample

The presence of complex matrix in the aquatic system affects the environmental behavior of hydrophobic organic compounds (HOCs). In the current study, an automated solid-phase microextraction (SPME) desorption method was employed to study the effect of 2-hydroxypropyl-β-cyclodextrin (β-HPCD) on the kinetic process of 5 selected polyaromatic hydrocarbons (PAHs) desorbing from the fiber in aqueous sample. The results showed that the added β-HPCD facilitated the desorption rates of PAHs from SPME fiber coating, and the enhancement effect can be predicted by a proposed theoretical model. Based on this model, the kinetic parameters of organic compounds desorbing from the SPME fiber can be determined, and the calculated results showed good agreement with the experimental data. In addition, the effect of temperature on the desorption kinetic was investigated. The results found that the SPME desorption time constant increased as the sampling temperature elevated, and followed the Arrhenius equation. Also, the temperature facilitated the desorption of HOCs from the bound matrix so that increased the lability degrees of the bound compounds. Finally, a calibration method based on the proposed theoretical model was developed and applied for the analysis of unknown sample.     

Initial bandwidth resulting from splitless and solid phase microextraction gas chromatographic injections

The initial width of the injected solute bands is a major determinant of the final measured peak width. While the individual processes contributing to this intial width have been observed and described qualitatively by many authors, little attention has been focused on their quantitative relationship. Using solid phase microextraction (SPME) and splitless injections of a hydrocarbon test mixutre the contributions to overall peak variance in SPME and splitless injections can be separated and quantitated. In SPME, it is seen that thermal focusing or rapid desorption must serve to provide focused bands. In splitless, thermal fucusing and solvent effects provide focusing. Variance contributions for each of these are calculated and shown.     

Gas chromatography-mass spectrometry determination of 3-mercaptohexan-1-ol and 3-mercaptohexyl acetate in wine: a comparison of headspace solid phase microextraction and solid phase extraction methods

A gas chromatography-mass spectrometry method was established using headspace solid phase microextraction (HS-SPME) as the sampling procedure to analyse 3-mercaptohexan-1-ol (3-MH) and 3-mercaptohexyl acetate (3-MHA), two molecules with a tropical fruit aroma, in wine at trace level. This method offers important advantages, as it neither requires time-consuming sample preparation nor uses dangerous organic compounds, thus making control of wine aroma easier and suitable for routine analysis. As a comparison, a solid phase extraction (SPE) method, already described elsewhere for aroma analysis, was applied to quantify these analytes, extending this exhaustive enrichment to two important thiols. Detection limits for both the approaches were close to the sensory threshold value, resulting lower for the HS-SPME procedure and suitable for requirements in the oenological field. The application of the two proposed methods to 52 wines of different varieties gave similar results.