Amphiphilic silica nanoparticles as pseudostationary phase for capillary electrophoresis separation

Amphiphilic silica nanoparticles surface-functionalized by 3-aminopropyltriethoxysilane (APTES) and octyltriethoxylsilane (OTES) were successfully prepared and characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectrometry (FT-IR) and thermogravimetry (TG) techniques. The potential use of these bifunctionalized nanoparticles as pseudostationary phases (PSPs) in capillary electrophoresis (CE) for the separation of charged and neutral compounds was evaluated in terms of their suitability. As expected, fast separation of representative aromatic acids was fulfilled with high separation efficiency, because they migrate in the same direction with the electroosmotic flow (EOF) under optimum experimental conditions. Using a buffer solution of 30mmol/L phosphate (pH 3.0) in the presence of 0.5mg/mL of the synthesized bifunctionalized nanoparticles, the investigated basic compounds were baseline-resolved with symmetrical peaks. Due to the existence of amino groups on the surface of nanoparticles, "silanol effect" that occurs between positively charged basic analytes and the silanols on the inner surface of capillary was greatly suppressed. Furthermore, the separation systems also exhibited reversed-phase (RP) behavior when neutral analytes were tested.     

Carbon nanotubes as separation carrier in capillary electrophoresis

The utility and versatility of carboxylic single-walled carbon nanotubes (c-SWNT) in capillary electrophoresis (CE) is demonstrated, using as model solutes homologues and structural isomers. In the case of homologues of caffeine and theobromine, distinct changes in the electrophoretic parameters occur at a critical concentration of c-SWNT in the run buffer. It is suggested that the c-SWNT of a definite concentration could form a network in the run buffer as a pseudostationary phase on the basis of the unique tubule structure, providing a different separation from sodium dodecyl sulfate (SDS) micelles. In the case of structural isomers of catechol and hydroquinone, differing from the homologues, it is mainly attributable to the functional groups on the c-SWNT that have an effect on the electrophoretic behaviors by forming intermolecular hydrogen bonding with analytes. Furthermore, aggregated c-SWNT serve as anticonvective media and minimize solute diffusion contributing to zone broadening. The presence of charged c-SWNT suppressed the electrodiffusion and decreased the adsorption between capillary wall and solutes, which led to better peak shapes of isomers.     

Studying the size/shape separation and optical properties of silver nanoparticles by capillary electrophoresis

This paper describes the feasibility of employing capillary electrophoresis (CE) to separate silver particles in nanometer regimes. We have found that the addition of an anionic surfactant, sodium dodecyl sulphate (SDS), to the running electrolyte prevents coalescence of the silver particles during the process, which improves the separation performance; the concentration of SDS required for optimal silver nanoparticle separation is ca. 20 mM. By monitoring the electropherograms using a diode-array detection (DAD) system, we have also investigated the separation of suspended silver nanorods with respect to their shapes. Our results demonstrate that the combination of CE and DAD is a powerful one for the separation and characterization of various silver nanoparticles.     

Adding sodium dodecylsulfate to the running electrolyte enhances the separation of gold nanoparticles by capillary electrophoresis

This paper describes employing capillary electrophoresis (CE) for the separation of gold colloids in nanometer-size regimes. Adding sodium dodecylsulfate (SDS) surfactant to the running buffer enhances the capability of CE to separate gold nanoparticles. We found that the optimized separation conditions involved SDS (70 mM), 3-cyclohexylamoniuopropanesulfonic acid (CAPS) buffer (10 mM), pH 10.0, and an applied voltage of 20 kV. We propose that the charged surfactants associate onto the surface of the gold nanoparticles and cause a change in the charge-to-size ratio of gold nanoparticle, which is a function of the surface area of nanoparticle and the surfactant concentration of running electrolyte. At high concentrations of the surfactant in the running electrolyte—i.e., when the surface of the gold nanoparticles is fully occupied with SDS—a linear relationship exists between the electrophoretic mobility and nanoparticles having diameters ranging from 5.3 to 38 nm. Based on the results of separating the 5.3 and 19 nm nanoparticles, we estimate that the size resolution (R_s=1.0) is 5.0 nm. The relative standard deviations of the electrophoretic mobilities of the 5.3 and 19 nm gold nanoparticles are 0.97 and 0.54%, respectively.     

毛细管电泳柱上安培检测装置的研制

介绍了一种新的毛细管电泳柱上安培检测装置。以碳纤维微电极为工作电极,在自组装的ACS－2000毛细管电泳仪上,测定了三种苯二酚的异构体：邻苯二酚、对苯二酚、间苯二酚,在20min内达到了基线分离。     

Enhanced separation of seven quinolones by capillary electrophoresis with silica nanoparticles as additive

This paper describes the enhanced separation of lomefloxacin, sparfloxacin, fleroxacin, norfloxacin, ofloxacin, gatifloxacin and pazufloxacin by capillary zone electrophoresis (CZE) using silica nanoparticles (SiNPs) as running buffer additive. The impact of SiNPs concentration on the resolution and selectivity of separation was investigated and a given value of SiNPs was finally chosen under the optimum conditions. The addition of the SiNPs to the running buffer enabled electroosmotic flow (EOF) decrease and permitted full interaction between SiNPs and analytes. The influence of separation voltage, pH and buffer concentration on the separation in the presence of SiNPs was examined. Interactions between drugs and nanoparticles during the separation are discussed; the determination of interaction constants is also achieved. A good resolution of seven quinolones was obtained within 15 min in a 50 cm effective length fused-silica capillary at a separation voltage of +10 kV in a 12 mM disodium tetraborate-phosphate buffer (pH 9.08) containing 5.2 μg mL⁻¹ SiNPs.     

Impact of the sample matrix composition on the signal enhancement in the capillary electrophoretic separation of poliovirus samples

The development of capillary electrophoretic applications aiming to provide reliable stability assessment of viral suspensions, to detect subviral particles from cell extracts or to study the interactions between virus particles and various biomolecules, cannot be done without a thorough understanding of the sample matrix contribution to the observed electrophoretic behaviour. The present study thoroughly investigates the effect of the sample matrix on the electrophoretic behaviour of poliovirus injected as sample plugs of 1%, 5% and 12% effective capillary length. The effect of the sample matrix for three different poliovirus batches was evaluated. Additionally, simulated samples, obtained from concentrated poliovirus suspensions of high purity and diluted with commonly used lab buffers in order to obtain samples with either high or low conductivities, were also investigated. The goal of the study was to obtain a better understanding of the effect of the sample matrix on the signal enhancement, in order to define a general approach allowing a repeatable capillary electrophoretic (CE) separation of poliovirus from complex samples. This study clearly demonstrates that the sample matrix has an important influence on the sensitivity of the CE poliovirus separations. Translation of these observations into routine practice involves several compromises and a set of rules in order to reduce day-to-day variation and to maximize sensitivity.     

Investigation of iron oxide nanoparticles by capillary zone electrophoresis

The electrophoretic behavior of γ-Fe₂O₃ nanoparticles was studied in aqueous solutions of Na₂SO₄-NaOH (pH 10.8) and of Na₂SO₄-Na₃cit (pH 7.1) as running electrolytes. Two electrophoretic zones (smooth and with spikes) due to colloidal and suspended particles of approximately the same size range were formed during the runs. The suspension stability and size distribution were shown to depend on the composition of electrolyte used for dispersing the solids. The effects of electric field strength, injection time, injection pressure as well as sodium citrate concentration were studied and particle electrophoretic mobilities were calculated. Electron micrographs of particles studied were obtained. Preparation of reference samples based on the colloidal γ-Fe₂O₃ has been discussed.     

Use of polystyrene nanoparticles to enhance enantiomeric separation of propranolol by capillary electrophoresis with Hp-beta-CD as chiral selector

We describe the use of polystyrene (PS) nanoparticles to manipulate chiral selectivity of propranolol analysis by capillary electrophoresis, by dispersing PS nanoparticles into the run buffer employing hydroxypropyl-β-cyclodextrin (HP-β-CD) as chiral selector. Distinct separational differences are observed between the buffer containing PS nanoparticles and buffer without, when changing separating conditions including PS nanoparticles concentration, pH, buffer concentration, HP-β-CD concentration and when adding an organic additive. Selectivity improvements are reflected by changes in the observed mobility as a result of interactions between the propranolol enantiomers and HP-β-CD governing the absorption process on the PS particles surface. The presence of PS nanoparticles increases the enantioseparation at low particle concentration in the presence of HP-β-CD as a chiral selector.     

Systematic investigations of different capillary electrophoretic techniques for separation of methylquinolines

The migration behaviour of isoquinoline, quinoline, and methyl derivatives of quinoline in different capillary electrophoretic modes has been systematically investigated. Optimised separation conditions were established by varying the key parameters (solvent, pH, temperature, surfactant concentration, core phase) for aqueous and non‐aqueous capillary zone electrophoresis (NACE), micellar electrokinetic chromatography (MEKC) with anionic or non‐ionic micelles (SDS, Brij 35), and microemulsion electrokinetic chromatography (MEEKC) with charged or uncharged microemulsion droplets. A separation of all quinolines could be achieved by MEEKC with charged droplets, by MEKC or by formamide‐based NACE. Comparing the separations with respect to separation selectivity, substantial changes in migration order could be observed between the different techniques. Regarding separation efficiency, the number of theoretical plates and limits of detection (LOD) have been compared. The best LODs were achieved using SDS as surfactant in MEKC, followed by MEEKC.     

Silica nanoparticles for separation of biologically active amines by capillary electrophoresis with laser-induced native fluorescence detection

This paper describes the analysis of biologically active amines by capillary electrophoresis (CE) in conjunction with laser-induced native fluorescence detection. In order to simultaneously analyze amines and acids as well as to achieve high sensitivity, 10 mM formic acid solutions (pH < 4.0) containing silica nanoparticles (SiNPs) were chosen as the background electrolytes. With increasing SiNP concentration, the migration times for seven analytes decrease as a result of increase in electroosmotic flow (EOF) and decrease in their electrophoretic mobilities against EOF. A small EOF generated at pH 3.0 reveals adsorption of SiNPs on the deactivated capillary wall. The decreases in electrophoretic mobilities with increasing SiNP concentration up to 0.3x indicate the interactions between the analytes and the SiNPs. Having a great sensitivity (the limits of detection at a signal-to-noise ratio (S/N) = 3 of 0.09 nM for tryptamine (TA)), high efficiency, and excellent reproducibility (less than 2.4% of the migration times), this developed method has been applied to the analysis of urinal samples with the concentrations of 0.50 +/- 0.02 microM, 0.49 +/- 0.04 microM, and 74 +/- 2 microM for TA, 5-hydroxytryptamine, and tryptophan, respectively. The successful examples demonstrated in this study open up a possibility of using functional nanoparticles for the separation of different analytes by CE.     

Capillary electrophoretic separation of toxic drugs using a polyacrylamide-coated capillary

Summary Capillary electrophoresis (CE) has recently become an attractive approach for the analysis of pharmaceuticals. In this study, capillary electrophoretic separation of anxiolytic drugs, including barbiturates and benzodiazepines, was carried out using polyacrylamide (PAA)-coated capillaries. The surface of the capillary inner wall was coated with a neutral layer, and separation was performed in the absence of electroosmotic flow (EOF). Both charged and neutral solutes were separated in the presence of sodium dodecyl sulfate (SDS) above its critical micelle concentration (CMC) in the running buffer. This kind of CE method provided fast and efficient separation of a total of 24 kinds of toxic drugs in a mixture. In addition, the analysis of toxic drugs in body fluids was attempted after the sample preparation using liquid-liquid extraction or solid-phase microextraction (SPME).     

Use of zwitterionic buffer additives to improve the separation of proteins in capillary zone electrophoresis

In CZE, the adsorption of the proteins on the capillary wall is a common problem. This paper describes the simple method of utilizing zwitterionic buffer additives to improve the separation of proteins in untreated fused silica capillaries at neutral pH. Three kinds of zwitterion are evaluated in the separation of acidic, neutral, and basic proteins, including their effect on protein efficiency, mobility, separation, and resolution; the difference between the effects of the different additives are also highlighted. The method has proved to be a possible means of reducing protein adsorption, especially for basic proteins.     

The application of functional silica nanoparticles to fulfill the rapid and improved enantioselective capillary electrophoresis separation of amino acid derivatives

In this study, diamino moiety functionalized silica nanoparticles with the size of 118 ± 12 nm were successfully synthesized and directly introduced into a chiral capillary electrophoresis system to improve the enantioseparation of 9‐fluorenyl methoxycarbonyl derivatized amino acids using norvancomycin as chiral selector. Under acidic background electrolyte conditions, functional silica nanoparticles can be readily adsorbed onto the inner surface of bare silica capillary column through electrostatic interaction to form a dynamic coating, resulting in a reversed anodic electro‐osmotic flow (i.e. from cathode to anode). As expected, chiral amino acid derivatives (usually negatively charged) can be rapidly separated under co‐electro‐osmotic flow conditions in the current separation system. Furthermore, the column performance and detection sensitivity for the enantioseparation were also obviously improved because the adsorption of chiral selector of norvancomycin to the capillary wall was greatly suppressed. Some important factors influencing the separation, such as the coating thickness, background electrolyte concentration, functional silica nanoparticles concentration, and the organic modifier were also investigated and the optimized separation conditions were obtained.     

Protein separation by capillary gel electrophoresis: A review

Capillary gel electrophoresis (CGE) has been used for protein separation for more than two decades. Due to the technology advancement, current CGE methods are becoming more and more robust and reliable for protein analysis, and some of the methods have been routinely used for the analysis of protein-based pharmaceuticals and quality controls. In light of this progress, we survey 147 papers related to CGE separations of proteins and present an overview of this technology. We first introduce briefly the early development of CGE. We then review the methodology, in which we specifically describe the matrices, coatings, and detection strategies used in CGE. CGE using microfabricated channels and incorporation of CGE with two-dimensional protein separations are also discussed in this section. We finally present a few representative applications of CGE for separating proteins in real-world samples.     

Development of a capillary electrophoretic method for the separation of diastereoisomers of a new human immunodeficiency virus protease inhibitor

A capillary electrophoretic (CE) method was developed for the separation of diastereoisomers of a new human immunodeficiency virus (HIV) protease inhibitor TMC114. In total 16 isomers of this drug have been synthesized (eight pairs of enantiomers). We succeeded in the separation of the eight diastereoisomers, but no enantiomers could be separated. Because of the high similarity and water-insolubility of these isomers, the separation is a real challenge. Different CE modes were tried out: capillary zone electrophoresis (CZE), nonaqueous capillary electrophoresis (NACE), micellar electrokinetic capillary chromatography (MEKC), and microemulsion electrokinetic capillary chromatography (MEEKC). Only MEEKC offered resolution of these compounds.     

Effect of buffer,electric field,and separation time on detection of aptamer-ligand complexes for affinity probe capillary electrophoresis

The separation and detection of complexes of aptamers and protein targets by capillary electrophoresis (CE) with laser-induced fluorescence was examined. Aptamer-thrombin and aptamer-immunoglobulin E (IgE) were used as model systems. Phosphate, 3-(N-morpholino)propanesulfonic acid with phosphate, and tris(hydroxyamino)methane-glycine-potassium (TGK) buffer at pH 8.4 were tested as electrophoresis media. Buffer had a large effect with TGK providing the most stable complexes for both protein-aptamer complexes. Conditions that suppressed electroosmotic flow, such as addition of hydroxypropylmethylcellulose to the media or modification of the capillary inner wall with polyacrylamide, were found to prevent detection of complexes. The effect of separation time and electric field were evaluated by monitoring complexes with electric field varied from 150-2850 V/cm and effective column lengths of 3.5 and 7.0 cm. As expected, shorter times on the column greatly increased peak heights for the complexes due to a combination of less dilution by diffusion and less dissociation on the column. High fields were found to have a detrimental effect on detection of complexes. It is concluded that the best conditions for detection of noncovalent complexes involve use of the minimal column length and electric field necessary to achieve separation. The results will be of interest in developing affinity probe CE assays wherein aptamers are used as affinity ligands.     

Recent advances in nanomaterial‐based capillary electrophoresis

This review gives a summary of applications of different nanomateials, such as gold nanoparticles (AuNPs), carbon‐based nanoparticles, magnetic nanoparticles (MNPs), and nano‐sized metal organic frameworks (MOFs), in electrophoretic separations. This review also emphasizes the recent works in which nanoparticles (NPs) are used as pseudostationary phase (PSP) or immobilized on the capillary surface for enhancement of separation in CE, CEC, and microchips electrophoresis.     

Capillary zone electrophoretic separation of basic proteins and drugs using guaran as a buffer modifier

Summary Guaran, a neutral polysaccharide, has been used as a buffer modifier to improve the separation of basic proteins and drugs. Migration reproductibility, peak shape and efficiency were improved when 0.1% guaran was added to the buffer. The concentration of guaran, ionic strength, and pH of buffer solution were optimized to obtain the optimum separation of proteins. Possible separation efficiencies of 700,000 plates per meter were obtained for test proteins. The relative standard deviation (% RSD) of the migration time of all test proteins was less than 0.5%. Improved separation of β-blockers was also observed when guaran was added to the buffer.