Effects of electrolytes used in roughening gold substrates by oxidation–reduction cycles on surface-enhanced Raman scattering

In this work, the effects of electrolytes used in roughening gold substrates by electrochemical methods on surface-enhanced Raman scattering (SERS) were first investigated. First, gold substrates were roughened by triangular-wave oxidation–reduction cycles (ORC) in aqueous solutions containing different kinds of 0.1 M electrolytes. Then Rhodamine 6G (R6G) was used as Raman probe to examine this effect of electrolytes used on the SERS observed. The result indicates that the highest intensity of SERS of R6G was obtained on the roughened Au substrate prepared in 0.1 M NaCl, which was less used in the literature. Meanwhile, it was also found that the rougher surface morphology observed, which is contributive to the higher SERS obtained, is corresponding to the smaller cathodic peak area shown in the cyclic voltammograms for roughening the Au substrate.     

Improved surface-enhanced Raman scattering on optimum electrochemically roughened silver substrates

In this work, the effects of preparation conditions used in roughening silver substrates by electrochemical triangular-wave oxidation-reduction cycles (ORC) on surface-enhanced Raman scattering (SERS) were first investigated. The optimum roughening conditions for obtaining strongest SERS of Rhodamine 6G (R6G) are as follows. Ag electrodes were cycled in deoxygenated aqueous solutions containing 0.1 M NaCl from −0.3 to +0.2 V versus Ag/AgCl at 25 mV s⁻¹ for five scans. The SERS of R6G adsorbed on this optimum procedure-prepared roughened Ag substrate exhibits a higher intensity by one order of magnitude, as compared with that of R6G adsorbed on a normally roughened Ag substrate.     

Highly reproducible surface-enhanced Raman scattering-active Au nanostructures prepared by simple electrodeposition: Origin of surface-enhanced Raman scattering activity and applications as electrochemical substrates

The fabrication of effective surface-enhanced Raman scattering (SERS) substrates has been the subject of intensive research because of their useful applications. In this paper, dendritic gold (Au) rod (DAR) structures prepared by simple one-step electrodeposition in a short time were examined as an effective SERS-active substrate. The SERS activity of the DAR surfaces was compared to that of other nanostructured Au surfaces with different morphologies, and its dependence on the structural variation of DAR structures was examined. These comparisonal investigations revealed that highly faceted sharp edge sites present on the DAR surfaces play a critical role in inducing a high SERS activity. The SERS enhancement factor was estimated to be greater than 10⁵, and the detection limit of rhodamine 6G at DAR surfaces was 10⁻⁸ M. The DAR surfaces exhibit excellent spot-to-spot and substrate-to-substrate SERS enhancement reproducibility, and their long-term stability is very good. It was also demonstrated that the DAR surfaces can be effectively utilized in electrochemical SERS systems, wherein a reversible SERS behavior was obtained during the cycling to cathodic potential regions. Considering the straightforward preparation of DAR substrates and the clean nature of SERS-active Au surfaces prepared in the absence of additives, we expect that DAR surfaces can be used as cost-effective SERS substrates in analytical and electrochemical applications.     

In-situ surface-enhanced Raman scattering and FT-Raman spectroscopy of black prints

The black inkjet and laser prints were analysed with regard to application in forensic analysis of questioned documents. The purpose of this work was to study spectral properties and compare the suitability of surface-enhanced Raman scattering (SERS) with Fourier transform Raman spectra of prints. This work aimed to find optimal surface-enhanced Raman spectroscopic approach for the future analysis of documents using statistical methods. In this work, we analysed eight prints of four laser and four inkjet devices. The samples were measured using two dispersive Raman devices; (DXR Raman microscope with excitation line 532 nm, Foram 685-2 spectrometer − 685 nm) and FT-Raman device (Bruker Spectrometer MultiRAM with excitation line 1064 nm). The silver nanoparticles (AgNPs) colloid for SERS experiment were synthesised and checked by UV–vis spectroscopy and scanning electron microscopy (SEM). The remarkable differences caused by centrifugation of silver colloid were observed just in the SEM images. The main contribution of this paper is to propose the novel approach achieving sufficient SERS signal intensity of black prints using the both, laser and inkjet printers. Moreover, this method is based on just a single metal colloid, and the analysis can be performed in-situ, i.e. directly on the printed sample surface. We consider the SERS could by highly promising and universal for applications in the forensic analysis of printed documents with the combination of statistical method when conventional methods are not effective.     

Silver-particle-based surface-enhanced resonance Raman scattering spectroscopy for biomolecular sensing and recognition

We demonstrate in this work that 2-μm-sized Ag (μAg) powders can be used as a core material for constructing biomolecular sensing/recognition units operating via surface-enhanced resonance Raman scattering (SERRS). This is possible because μAg powders are very efficient substrates for both the diffuse reflectance IR and the surface-enhanced Raman scattering–SERRS spectroscopic characterization of molecular adsorbates prepared in a similar manner on silver surfaces. Besides, the agglomeration of μAg particles in a buffer solution can be prevented by the layer-by-layer deposition of cationic and anionic polyelectrolytes such as poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA). In this particular study, we used rhodamine B isothiocyanate (RhBITC) as a SERRS marker molecule, and μAg powders adsorbed consecutively with RhBITC and PAH–PAA bilayers were finally derivatized with biotinylated poly(l-lysine). On the basis of the nature of the SERRS peaks of RhBITC, those μAg powders were confirmed to selectively recognize streptavidin molecules down to concentrations of 10⁻¹⁰ g mL⁻¹. Since a number of different molecules can be used as SERS–SERRS marker molecules, the present method proves to be an invaluable tool for multiplex biomolecular sensing/recognition via SERS and SERRS.     

A dual-functional membrane for bisphenol A enrichment and resonance amplification by surface-enhanced Raman scattering

A dual-functional membrane with enrichment and resonance amplification property, combined with an automatic sampler was designed for bisphenol A detection by surface-enhanced Raman scattering.     

Improved surface-enhanced Raman scattering on electrochemically roughened silver substrates prepared in bielectrolyte solutions

In this work, the effect of supplemental LiClO₄ electrolytes in KCl solutions used in roughening silver substrates by electrochemical triangular-wave oxidation-reduction cycles (ORC) on surface-enhanced Raman scattering (SERS) was first investigated. To prepare SERS-active substrates by ORC procedures, electrolytes of KCl were generally employed. In contrast, LiClO₄ ones were unsuitable for producing SERS-active substrates. Encouragingly, SERS of Rhodamine 6G (R6G) adsorbed on the roughened Ag substrate prepared in an aqueous solution containing KCl and LiClO₄ electrolytes exhibits a higher intensity by one order of magnitude, as compared with that of R6G adsorbed on a roughened Ag substrate prepared in a solution only containing KCl. Further investigations indicate that the oxidation state of Cl on the roughened Ag substrate demonstrates decided effects on this improved SERS.     

Explosive and chemical threat detection by surface-enhanced Raman scattering: A review

Acts of terror and warfare threats are challenging tasks for defense agencies around the world and of growing importance to security conscious policy makers and the general public. Explosives and chemical warfare agents are two of the major concerns in this context, as illustrated by the recent Boston Marathon bombing and nerve gas attacks on civilians in the Middle East. To prevent such tragic disasters, security personnel must be able to find, identify and deactivate the threats at multiple locations and levels. This involves major technical and practical challenges, such as detection of ultra-low quantities of hazardous compounds at remote locations for anti-terror purposes and monitoring of environmental sanitation of dumped or left behind toxic substances and explosives. Surface-enhanced Raman scattering (SERS) is one of todays most interesting and rapidly developing methods for label-free ultrasensitive vibrational “fingerprinting” of a variety of molecular compounds. Performance highlights include attomolar detection of TNT and DNT explosives, a sensitivity that few, if any, other technique can compete with. Moreover, instrumentation needed for SERS analysis are becoming progressively better, smaller and cheaper, and can today be acquired for a retail price close to 10,000 US$. This contribution aims to give a comprehensive overview of SERS as a technique for detection of explosives and chemical threats. We discuss the prospects of SERS becoming a major tool for convenient in-situ threat identification and we summarize existing SERS detection methods and substrates with particular focus on ultra-sensitive real-time detection. General concepts, detection capabilities and perspectives are discussed in order to guide potential users of the technique for homeland security and anti-warfare purposes.     

Low-frequency surface-enhanced Raman scattering spectroscopy at metal electrode surfaces

Low-frequency surface-enhanced Raman scattering (SERS) spectroscopy is a versatile tool for studying surface phenomena under electrochemical conditions. This spectroscopy enables us to obtain rich information on extramolecular vibrations between substrate and adsorbates, which are sensitive to atomistic surface features of the substrate. Owing to recent advancements in optical filter technology, low-frequency SERS signals are now becoming easily detectable using conventional Raman systems equipped with holographic notch filters. In addition, SERS background signals, which have been simply ignored, can provide electronic information on the metal substrate. This allows us to observe both sides of electrode–electrolyte interfaces in situ and simultaneously, which is never expected in far-infrared or terahertz absorption spectroscopy. This advanced SERS spectroscopy can help our understanding of electrochemical and electrocatalytic reactions at the molecular scale.     

Fabrication of bimetallic microfluidic surface-enhanced Raman scattering sensors on paper by screen printing

Au–Ag bimetallic microfluidic, dumbbell-shaped, surface enhanced Raman scattering (SERS) sensors were fabricated on cellulose paper by screen printing. These printed sensors rely on a sample droplet injection zone, and a SERS detection zone at either end of the dumbbell motif, fabricated by printing silver nanoparticles (Ag NPs) and gold nanoparticles (Au NPs) successively with microscale precision. The microfluidic channel was patterned using an insulating ink to connect these two zones and form a hydrophobic circuit. Owing to capillary action of paper in the millimeter-sized channels, the sensor could enable self-filtering of fluids to remove suspended particles within wastewater without pumping. This sensor also allows sensitive SERS detection, due to advantageous combination of the strong surface enhancement of Ag NPs and excellent chemical stability of Au NPs. The SERS performance of the sensors was investigated by employing the probe rhodamine 6G, a limit of detection (LOD) of 1.1 × 10⁻¹³ M and an enhancement factor of 8.6 × 10⁶ could be achieved. Moreover, the dumbbell-shaped bimetallic sensors exhibited good stability with SERS performance being maintained over 14 weeks in air, and high reproducibility with less than 15% variation in spot-to-spot SERS intensity. Using these dumbbell-shaped bimetallic sensors, substituted aromatic pollutants in wastewater samples could be quantitatively analyzed, which demonstrated their excellent capability for rapid trace pollutant detection in wastewater samples in the field without pre-separation.     

Partition layer-modified substrates for reversible surface-enhanced Raman scattering detection of polycyclic aromatic hydrocarbons

Herein, we present progress towards an analytical sensor for polycyclic aromatic hydrocarbons (PAHs) using surface-enhanced Raman scattering (SERS) on partition layer-modified nanostructured substrates. Specifically, a 1-decanethiol monolayer has been assembled on a silver film over nanospheres substrate to concentrate PAHs within the zone of SERS detection. Both anthracene and pyrene were detected with limits of detection at 300 and 700 pM, respectively. The measured SERS spectra allowed for easy distinction of the two PAH compounds, due to varying peak locations, and insight into the partitioning mechanism. Additionally, exposure to a common environmental interferant, Suwannee River fulvic acid, did not impede the measurement of the PAHs, and the sensor is reusable after a short exposure to 1-octanol. Finally, the utility of this sensing platform for PAH detection was compared to that achievable for other classes of organic pollutants such as polychlorinated biphenyls and polybrominated diphenyl ethers. Figure SERS detection of polycyclic aromatic hydrocarbons facilitated via partition layer modified substrates.

Temporal evolution of Raman intensities on surface-enhanced Raman scattering active copper and gold electrodes at negative potentials

The effect of a roughening procedure on surface-enhanced Raman scattering (SERS) intensity of pyridine at copper and gold electrodes subjected to negative potential has been investigated. Among four procedures tested for a copper electrode the one consisting of electrochemical activation in a solution of LiCl and CuCl₂ resulted in the most stable and effective surface. It was proved that the presence of pyridine during the pretreatment procedure caused a very fast, irreversible decay of SERS intensity for both copper and gold electrodes. Quite stable, at least at room temperatures, gold surfaces were obtained by oxidation-reduction cycles activation in KCl solution.     

A simple approach for ultrasensitive detection of bisphenols by multiplexed surface-enhanced Raman scattering

Bisphenol A (BPA) is well known for its use in plastic manufacture and thermal paper production despite its risk of health toxicity as an endocrine disruptor in humans. Since the publication of new legislation regarding the use of BPA, manufacturers have begun to replace BPA with other phenolic molecules such as bisphenol F (BPF) and bisphenol B (BPB), but there are no guarantees regarding the health safety of these compounds at this time. In this context, a very simple, cheap and fast surface-enhanced Raman scattering (SERS) method was developed for the sensitive detection of these molecules in spiked tap water solutions. Silver nanoparticles were used as SERS substrates. An original strategy was employed to circumvent the issue of the affinity of bisphenols for metallic surfaces and the silver nanoparticles surface was functionalized using pyridine in order to improve again the sensitivity of the detection. Semi-quantitative detections were performed in tap water solutions at a concentrations range from 0.25 to 20 μg L⁻¹ for BPA and BPB and from 5 to 100 μg L⁻¹ for BPF. Moreover, a feasibility study for performing a multiplex-SERS detection of these molecules was also performed before successfully implementing the developed SERS method on real samples.     

Interaction of soil humic acids with herbicide paraquat analyzed by surface-enhanced Raman scattering and fluorescence spectroscopy on silver plasmonic nanoparticles

A study of the interaction between paraquat (methyl viologen) and humic acids, extracted from a soil amended over 30 years with crop residues, cow slurries and cattle manure, was carried out by two emission spectroscopies based on plasmonic effects: surface-enhanced Raman scattering (SERS) and surface-enhanced fluorescence (SEF). To carry out this study Ag nanoparticles were used. The complex formation was tested by analyzing the effect of the herbicide on humic acids, and by varying experimental parameters such as the pH and the laser excitation wavelength. The study of the vibrational bands led to infer information about the interaction mechanism of paraquat with humic acids and to find a correlation between this interaction and the humic acids structural modification induced by the different amendments added to soil.     

Stellate porous silica based surface-enhanced Raman scattering system for traceable gene delivery

Numerous nanocarriers have been currently developed for intracellular delivery. The potential cytotoxicity of these very small inorganic nanocarriers has raised great consideration. Thus, it becomes of utmost importance to conduct the intracellular trace of nanocarriers. Among many analytical techniques, surface enhanced Raman scattering(SERS) method is one of the current state-of-the-art techniques for cell visualization and trace. In this work, a novel stellate porous silica based gene delivery system has been designed for SERS trace purpose. A stellate porous silica nanoparticle modified with many small Au nanoparticles is designed to replace common metallic SERS tags. The results show that the designed system not only could deliver si RNA into cells for therapy, but also could realize SERS trace with high sensitivity and non-invasive features. The constructed delivery system has considerable potential to trace the dynamic gene delivery in living cells.     

Direct evidence of chemical effect of surface-enhanced Raman scattering observed on electrochemically prepared rough gold substrates

In this study, polypyrrole (PPy) films were electrochemically deposited on gold substrates roughened by an electrochemical triangular-wave oxidation-reduction cycles (ORC) in an aqueous solution containing 0.1N KCl. Then the substrates were heated from 25 to 50 °C and the corresponding SERS performances of PPy were observed in situ. The results indicate that the SERS enhancement capabilities of substrates are gradually raised from 25 °C to a maximum at 40 °C and monotonically decreased from 40 to 50 °C. These SERS enhancement capabilities ascribed to the charge transfers from PPy to Au, which are responsible for the chemical effects of SERS mechanisms, are successfully observed via SERS and high resolution X-ray photoelectron spectroscopy (HRXPS) analyses. The variation in content of the oxidized PPy peak of the double peaks in the range of 1000-1150 cm⁻¹ in SERS spectrum obtained on an Au substrate at different temperatures is consistent with its corresponding variation in the SERS intensity of PPy. The variation in content of the oxidized nitrogen of PPy deposited on an Au substrate at different temperatures revealed from an HRXPS analysis also confirms this consistence.     

Biocompatible core-shell nanoparticle-based surface-enhanced Raman scattering probes for detection of DNA related to HIV gene using silica-coated magnetic nanoparticles as separation tools

A novel, highly selective DNA hybridization assay has been developed based on surface-enhanced Raman scattering (SERS) for DNA sequences related to HIV. This strategy employs the Ag/SiO₂ core-shell nanoparticle-based Raman tags and the amino group modified silica-coated magnetic nanoparticles as immobilization matrix and separation tool. The hybridization reaction was performed between Raman tags functionalized with 3′-amino-labeled oligonucleotides as detection probes and the amino group modified silica-coated magnetic nanoparticles functionalized with 5′-amino-labeled oligonucleotides as capture probes. The Raman spectra of Raman tags can be used to monitor the presence of target oligonucleotides. The utilization of silica-coated magnetic nanoparticles not only avoided time-consuming washing, but also amplified the signal of hybridization assay. Additionally, the results of control experiments show that no or very low signal would be obtained if the hybridization assay is conducted in the presence of DNA sequences other than complementary oligonucleotides related to HIV gene such as non-complementary oligonucleotides, four bases mismatch oligonucleotides, two bases mismatch oligonucleotides and even single base mismatch oligonucleotides. It was demonstrated that the method developed in this work has high selectivity and sensitivity for DNA detection related to HIV gene.     

A colorimetric and surface-enhanced Raman scattering dual-signal sensor for Hg based on Bismuthiol II-capped gold nanoparticles

The addition of Bismuthiol II to the gold nanoparticles (AuNPs) solution led to the aggregation of AuNPs with a color change from red to blue. As a result, hot spots were formed and strong surface-enhanced Raman scattering (SERS) signal of Bismuthiol II was observed. However, the Bismuthiol II-induced aggregation of AuNPs could be reversed by Hg²⁺ in the system, accompanied by a remarkable color change from blue to red. As evidenced by UV–vis and SERS spectroscopy, the variation in absorption band and SERS intensity was strongly dependent on the concentration of Hg²⁺, suggesting a colorimetric and SERS dual-signal sensor for Hg²⁺. The sensor had a high sensitivity, low detection limits of 2 nM and 30 nM could be achieved by UV–vis spectroscopy and by SERS spectroscopy, respectively. Other environmentally relevant metal ions did not interfere with the detection of Hg²⁺. The method was successfully applied to detect Hg²⁺ in water samples. It was simple, rapid and cost-effective without any modifying or labeling procedure.     

Photochemical decoration of silver nanoparticles on magnetic microspheres as substrates for the detection of adenine by surface-enhanced Raman scattering

In this work, silver nanoparticles (AgNPs) decorated magnetic microspheres (MMs) are prepared as surface-enhanced Raman scattering (SERS) substrate for the analysis of adenine in aqueous solutions. To prepare these substrates, magnetic particles were first synthesized by coprecipitation of Fe(II) and Fe(III) with ammonium hydroxide. A thin layer of cross-linked polymer was formed on these magnetic particles by polymerization through suspension of magnetic particles into a solution of divinyl benzene/methyl methacrylate. The resulted polymer protected magnetic particles are round in shape with a size of 80 μm in diameter. To form AgNPs on these MMs, photochemical reduction method was employed and the factors in photochemical reduction method were studied and optimized for the preparation of highly sensitive and stable AgNPs on MMs substrates (abbreviated as AgMMs substrates). By dispersing the AgMMs in aqueous samples, cylindrical magnet was used to attract the AgMMs for SERS detections. The observed enhancement factor of AgMMs reached 7 orders in magnitude for detection of adenine with a detection limit approaching to few hundreds of nanomolar.     

Surface-enhanced Raman scattering detection of lysophosphatidic acid

Surface-enhanced Raman scattering using silver nanoparticles was applied to detect various forms of lysophosphatidic acid (LPA) to examine its potential application as an alternative to current detection methods of LPA as biomarkers of ovarian cancer. Enhancement of the Raman modes of the molecule, especially those related to the acyl chain within the 800–1300 cm⁻¹ region, was observed. In particular, the C–C vibration mode of the gauche-bonded chain around 1100 cm⁻¹ was enhanced to allow the discrimination of two similar LPA molecules. Given the molecular selectivity of this technique, the detection of LPA using SERS may eliminate the need for partial purification of samples prior to analysis in cancer screening.