疏水缔合聚丙烯酰胺与阳离子双子表面活性剂的相互作用

通过表面张力法和电导率法分别考察了阳离子双子表面活性剂(12-2-12)与非离子疏水缔合聚丙烯酰胺(HMPAM)和普通聚丙烯酰胺(PAM),传统表面活性剂十二烷基三甲基溴化铵(DTAB)与HMPAM和PAM之间的相互作用。结果表明,12-2-12 HMPAM复合体系与12-2-12水溶液体系相比,在w(聚合物含量)CMC时,复合体系的电导率(κ)具有下降的趋势,且κ随着w的增大下降的趋势越明显,说明12-2-12与HMPAM之间存在相互作用。     

表面活性剂对驱油聚合物界面剪切流变性质的影响

利用双锥法研究了表面活性剂十二烷基苯磺酸钠(SDBS)和十六烷基三甲基溴化铵(CTAB)对油田现场用部分水解聚丙烯酰胺(PHPAM)和疏水改性聚丙烯酰胺(HMPAM)溶液的界面剪切流变性质的影响,实验结果表明:HMPAM分子通过疏水作用形成界面网络结构,界面剪切复合模量明显高于PHPAM.SDBS和CTAB通过疏水相互作用与HMPAM分子中的疏水嵌段形成聚集体,破坏界面网络结构,剪切模量随表面活性剂浓度增大明显降低.同时,界面膜从粘性膜向弹性膜转变.低SDBS浓度时,少量SDBS分子与PHPAM形成混合吸附膜,界面膜强度略有升高;SDBS浓度较高时,界面层中PHPAM分子被顶替,吸附膜强度开始减弱.阳离子表面活性剂CTAB通过静电相互作用中和PHPAM分子的负电性,造成聚合物链的部分卷曲,从而降低界面膜强度.弛豫实验结果证实了表面活性剂破坏HMPAM网络结构的机理.     

Interaction Between the Hydrophobically Modified Polyacrylamide and HPAM-Flooding Produced Liquid

In order to utilize the produced liquid of hydrolyzed polyacrylamide (HPAM) flooding to enhance oil recovery, the interaction between hydrophobically modified polyacrylamide (HMPAM) and the produced liquid of HPAM flooding was investigated. The viscous characteristic of HMPAM in aqueous solution was investigated by Ubbelohde viscometer. The results show the intrinsic viscosity of HMPAM in aqueous solution is higher than that of HPAM, indicating that HMPAM has better effect on increasing the viscosity of aqueous solution. The viscosity of the complex system consisted of HMPAM and the produced liquid from HPAM flooding is lower than that of the HMPAM system, but higher than that of the HMPAM/HPAM complex system in mineralized water. In order to investigate the major factor of the influence on the viscosity of the HMPAM/produced liquid complex system, the viscosities of HMPAM/HPAM (and hydrolyzed HPAM with different hydrolysis degree) in distilled water and in mineralized water were studied. The fluorescence spectrum and transmission electron microscopy measurements were carried out to investigate the interaction between HPMAM and produced liquid from a microscopic perspective. These results are useful for farther enhancing oil recovery after HPAM flooding.     

疏水改性聚丙烯酰胺的荧光研究

使用荧光探针技术,跟踪了疏水改性聚丙烯酰胺(HMPAM)在溶液中的变化过程,对HMPAM在溶液中的聚集行为进行了研究。同时也对部分水解聚丙烯酰胺(HPAM)作了对比研究。发现HMPAM在溶液中具有独特的变化规律:由疏水缔合形成超分子聚集体,再由超分子聚集体形成布满整个溶液空间网络结构的过程。并使用粘度法对其宏观流变性能进行了研究,发现两种手段所得的结果具有较好的对应关系。     

疏水改性聚丙烯酰胺的增粘机理研究

通过与聚丙烯酰胺（PAM）对比,使用荧光光谱、紫外光谱、原子力显微镜以及流变性实验对疏水改性聚丙烯酰胺(HMPAM)的溶液行为和微观结构进行了研究.通过荧光实验I3/I1值的变化确定了HMPAM的临界缔合浓度.结合荧光、紫外及流变性实验,对HMPAM在溶液中通过疏水缔合形成疏水微区、超分子聚集体及发展到空间网络的结构变化进行了研究.用原子力显微镜证实了HMPAM溶液中网络结构的存在.对HMPAM表现出的特殊流变性从微观上找到了依据,提出了HMPAM的增粘机理.     

Modification of the stability of oil-in-water nano-emulsions by polymers with different structures

The effect of polymers (hydrolyzed polyacrylamide (HPAM) and hydrophobically modified polyacrylamide (HMPAM)) on the stability of oil-in-water nano-emulsions has been studied in paraffin oil/Span 20-Tween 20/water systems by method of phase inversion composition (PIC). The stabilization of nano-emulsions was investigated by visual observation and the change of water content induced by centrifugation. Droplet size distributions of nano-emulsions were obtained by a laser-scanner particle size distribution analyzer. The interfacial tension and charge of nano-emulsions were obtained by interfacial tension and zeta potential measurements. All the results indicate that the droplet size can be decreased by the addition of HMPAM, while almost no change could be observed when the HPAM was added. Meanwhile, HMPAM has a better effect on the stabilization of nano-emulsions than HPAM. It may conclude that the HMPAM molecules adsorbed at the oil/water interface of the nano-emulsion droplets. Therefore, the stability of nano-emulsion with the addition of HMPAM is based on both an associative thickening mechanism caused by the alkyl chains of HMPAM molecules and the adsorption of HMPAM at the oil/water interface, which can form a solid film to prevent the Ostwald ripening of nano-emulsion droplets.     

Effect of hydrophobically modified polymer on salt-induced structural transition in microemulsions

The phase boundaries of the middle-phase microemulsion for NaCl/SDS/H2O/1-heptane/1-pentanol systems in the absence of polymer and in the presence of unmodified poly(acrylamide) (PAM) and hydrophobically modified poly(acrylamide) (HMPAM) have been determined at varying salt concentrations. These three middle-phase microemulsions (with HMPAM, with PAM, and without polymer) were studied using interfacial tension measurement, steady-state fluorescence, and time-resolved fluorescence quenching. Compared to the polymer-free system and the system with PAM, the addition of HMPAM significantly enlarges the range of the salt concentrations for the formation of the middle-phase microemulison and causes both the excess oil and aqueous phases to increase in volume at the expense of the middle-phase microemulsion. For the middle-phase microemulsion with HMPAM, the interfacial tensions of the microemulsion phase with the excess oil phase and with the excess aqueous phase are all ultralow and exhibit higher values than those with PAM and without polymer. At the same salt concentration, the apparent surfactant aggregation number in the middle-phase microemulsion with HMPAM has the smallest value among these three systems. All results indicate that the strong interaction of surfactant with hydrophobically modified polymer has a large effect on the formation and properties of the middle-phase microemulsion.     

Preparation and solution properties of a novel cationic hydrophobically modified polyacrylamide for enhanced oil recovery

Abstract

A novel cationic water-soluble monomer allyldimethylisooctylammonium bromide (ADIAB) containing a short-chain alkane was synthesized successfully. This monomer was copolymerized with acrylamide and sodium acrylate to produce hydrophobically modified polyacrylamide (HMPAM) using solution polymerization without surfactants. The structures of monomer ADIAB and HMPAM were characterized with infrared spectroscopy and nuclear magnetic resonance spectroscopy. Influence of preparation condition on viscosities of products was studied. The aqueous solution viscosity of the terpolymer was also investigated as functions of concentration, temperature and salinity. The results showed that when the temperature exceeds the 60?°C and NaCl concentration exceeds about 2000?mg/L, the temperature and salt tolerance characters of terpolymer were demonstrated. The enhanced oil recovery tests were initially carried out using homogeneous sandpack models.     

On the Origin of Foam Stability: Understanding from Viscoelasticity of Foaming Solutions and Liquid Films

The foam stability (drainage half-life) of α-olefin sulfonate (AOS) with partially hydrolyzed polyacrylamide (HPAM) or xanthan gum (XG) solution was evaluated by the Warring Blender method. With the increase of polymer (HPAM or XG) concentration, foam stability of the surfactant–polymer complexes increased, and the drainage half-life of AOS-XG foam was higher than that of AOS-HPAM foam at the same polymer and surfactant concentration. With the addition of polymer (HPAM or XG), the viscoelasticity of bulk solution and the liquid film were enhanced. The viscoelasticity of AOS-XG bulk solution and liquid film were both higher than that of AOS-HPAM counterparts.      

驱油体系化学剂间相互作用对界面吸附膜的影响

采用界面张力弛豫技术研究了不对称Gemini表面活性剂C12COONa-p-C9SO3Na、部分水解聚丙烯酰胺Mo-4000、疏水缔合水溶性聚丙烯酰胺(HMPAM)等驱油体系化学剂在癸烷/水界面上的扩张流变性质,考察了不同离子强度、不同类型电解质对体系界面流变性质的影响,计算得到界面扩张弹性模量和粘性模量的全频率谱,并通过归一化方法(cole-cole图)探讨了界面吸附膜的弛豫过程。研究发现,界面膜内分子重排和界面与体相间分子扩散交换是影响膜性质的主要弛豫过程。表面活性剂体相浓度增大有利于界面分子重排过程,而低频有利于扩散交换过程;不同结构聚合物以及不同离子强度、不同类型电解质对表面活性剂吸附膜有不同的影响。     

Effect of Polymer on Dynamic Interfacial Tensions of Anionic–nonionic Surfactant Solutions

The dynamic interfacial tensions (IFTs) of enhanced oil recovery (EOR) surfactant/polymer systems against n-decane have been investigated using a spinning drop interfacial tensiometer in this paper. Two anionic–nonionic surfactants with different hydrophilic groups, C₈PO₆EO₃S (6-3) and C₈PO₆EO₆S (6-6), were selected as model surfactants. Partially hydrolyzed polyacrylamide (HPAM) and hydrophobically modified polyacrylamide (HMPAM) were employed. The influences of surfactant concentration, temperature, polymer concentration, and oleic acid in the oil on IFTs have been studied. The experimental results show that anionic–nonionic surfactants can form compact adsorption films and reach ultralow IFT (10^?3 mN/m) under optimum conditions. The addition of polymer has great influence on dynamic IFTs between surfactant solutions and n-decane mainly by the formation of looser mixed films resulting from the penetration of polymer chains into the interface. The compact surfactant film will also be weakened by the competitive adsorption of oleic acid, which results in the increase of IFT. Moreover, the penetration of polymer chains will be further destroyed surfactant/polymer mixed layer and lead to the obvious increase of IFT. On the other hand, polymers show little effect on the IFTs of 6-6 systems than those of 6-3 because of the hindrance of longer EO chain of 6-6 at the interface.     

疏水改性聚丙烯酰胺对原油组分界面扩张流变性质的影响

利用悬挂滴方法研究了疏水改性聚丙烯酰胺(HMPAM)对胜利采油厂高温高盐油藏采出原油中酸性活性组分和沥青质界面膜扩张流变性质的影响,考察了不同活性组分浓度条件下的界面扩张流变行为.实验结果表明:1750mg·L-1HMPAM能够在界面上形成网络结构,界面扩张模量数值高达100mN·m-1左右;油相中的酸性组分随着老化时间增加吸附到界面上,与HMPAM分子的疏水改性部分形成聚集结构,一方面通过快速的扩散交换过程大大降低扩张模量,另一方面通过与疏水改性部分的相互作用加强HMPAM分子间的缔合强度,增强网络结构的弹性.沥青质分子尺寸相对较大,分子间存在氢键等较强的相互作用,造成沥青质界面聚集体和HMPAM形成的网络结构共同决定界面膜性质,混合膜的扩张模量较单独HMPAM体系仅略有降低.     

Effects of poly(N‐isopropylacrylamide) on the solution properties of hydrophobically modified acrylamide copolymer

The hydrophobic interaction between hydrophobically modified acrylamide copolymer (HMPAM) and poly(N‐isopropylacrylamide) (PNIPAM) in aqueous solutions was investigated. The results show that the solution properties of HMPAM are significantly influenced by the addition of PNIPAM. In dilute regime, the intrinsic viscosity of HMPAM in 0.025 wt % PNIPAM/0.1 M NaCl mixed solution is 17.52 dL g^?1, about 2 times 8.66 dL g^?1, that in 0.1 M NaCl solution, which is due to the attractive interaction between the hydrophobic parts of PNIPAM and HMPAM molecules. In semidilute regime, below the saturation concentration, the addition of PNIPAM can lead to both the apparent viscosity and the modulus of HMPAM solutions increasing, which is attributed to the number of aggregation junctions increasing, responsible for the increase of the contribution of the reversible network to the viscosity increase, the β value. In addition, a thermothickening behavior for the HMPAM/PNIPAM mixed solution is observed with increasing temperature over 15–30 °C, which is consistent with the large increase of the Huggins coefficient of HMPAM in the presence of PNIPAM from 1.95 to 7.59 as temperature increases from 25 to 30 °C. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 709–715, 2005     

Influence of polymers on dust-related foam properties of sodium dodecyl benzene sulfonate with Foamscan

Foamability, liquid holdup, and foam appearance are key factors that determine dust control efficiencies. As the foam production method of the FoamScan instrument is similar to foaming device used for dust control, and its measurement means can satisfy the requirements of precise measuring, the FoamScan technology is adopted to explore the influence of xanthan gum (XG) and partial hydrolytic polyacrylamide (HPAM) on dust-related foam properties of sodium dodecyl benzene sulfonate (SDBS). It was found that with the increase of the polymer mass fraction, the liquid volume in the foam gradually increased. Additionally, the foaming time t₂₀₀ of the foaming agent decreased at first, then remained almost constant for both polymers, which indicated that the foamability and liquid holdup were enhanced by the addition of polymers into SDBS. In addition, the efficiencies of XG are higher than that of HPAM. The image analysis using the CSA software revealed that the mean radius formed by XG was smaller than that by HPAM and the number of bubbles was larger with XG than with HPAM. Thus, the XG foam has more area to contact with dust and could control dust better. The highly branched molecular structure and hydrogen bonds formed by XG played important roles in dust-related foam properties.     

Advances in DNA electrophoresis in polymer solutions.

DNA electrophoresis in gels and solutions of agarose and polyacrylamide was objectively evaluated with regard to separation efficiency at optimal polymer concentrations. In application to DNA fragments, polyacrylamide gels were superior for separating fragments of less than 7800 bp, and agarose gels are the best choice for larger fragments. Agarose solutions are nearly as good as polyacrylamide gels for small DNA (< 300 bp). Agarose solutions have a higher efficiency than polyacrylamide solutions for DNA of less than 1200 bp. Separation efficiency sharply decreases with increasing length of DNA. Retardation in polyacrylamide solutions was found to depend on polymer length in a biphasic fashion. The choice of resolving polymer concentrations depends on the progressive stretching of DNA in proportion to polymer concentration. The rate of that stretching appears higher in polyacrylmide solution than in gels or in liquid or gelled agarose. Application of polymer solutions to capillary electrophoresis raises further problems concerning agarose plugs, DNA interactions with the polymers, operation at low field strength and long durations as well as detection sensitivity.     

Extraction of uranium from aqueous solution by phosphonic acid-imbedded polyurethane foam

Phenylphosphonic acid was imbedded into the matrix of the polyurethane foam during the fabrication process of the polymer. The extraction of uranium by phosphonic acid-imbedded polyurethane foam and blank polyurethane (i.e., foam without phosphonic acid functional groups) was investigated. Phosphonic acid-imbedded foam showed superior extractability of uranium from solutions with pH=7.0+/-1.5 over a wide range of temperature.     

Polyelectrolyte and surfactant mixed solutions. Behavior at surfaces and in thin films

Dilute mixed solutions of non-surface active anionic polymers (polyacrylamide and polystyrene sulfonate, xanthan) and various surfactants have been studied with several methods: surface tension, ellipsometry, X-ray and neutron reflectivity, thin film balance, surface and bulk rheology. A strong synergistic lowering of the surface tension is found with cationic surfactants in the concentration range where no appreciable complexation of surfactant and polymer occurs in the bulk solution (as seen from viscosity measurements). Despite appreciable differences between surface tension behaviour, the adsorbed layer is very similar for all the polymers: their thickness is small and the polymer chains are stretched along the surface. The surface tension behaviour of these polymers with non-ionic surfactants is also different. When the polymers are confined in thin films, the forces between surfaces are similar, and independent of surfactant nature: oscillatory forces are measured, which reflect the existence of a polymer network with a well defined mesh size. The connection of foam stability with surface and bulk complexation is far from clear.     

Interactions of cationic gemini surfactants with hydrophobically modified poly(acrylamides) studied by fluorescence and microcalorimetry

Steady-state fluorescence, time-resolved fluorescence quenching, and isothermal titration microcalorimetry have been used to study the interactions of cationic gemini surfactants alkanediyl-alpha,omega-bis(dodecyldimethylammonium bromide) (C(12)C(S)C(12)Br(2), S = 3, 6, and 12) with hydrophobically modified poly(acrylamide) (HMPAM) and unmodified poly(acrylamide) (PAM). Without addition of gemini surfactant, 0.2 wt % HMPAMs except PAM have already self-aggregated into hydrophobic aggregates. Different from single-chain surfactants, C(12)C(S)C(12)Br(2) have stronger interactions with HMPAMs to form surfactant/polymer aggregates, even with PAM. Addition of C(12)C(S)C(12)Br(2) may cause the disruption of HMPAM hydrophobic aggregates and the formation of mixed micelles. It is found that HMPAMs generate lower micropolarity of mixed micelles, larger values of enthalpy of interaction (DeltaH(ps)), and nearly constant values of Gibbs free energy of interaction (DeltaG(ps)). On the other hand, C(12)C(S)C(12)Br(2) with longer spacer brings out slightly lower micropolarity of mixed micelles, owing to the lower electrostatic repulsion between surfactant headgroups. Especially for C(12)C(12)C(12)Br(2), the values of DeltaH(ps) are much more endothermic and the values of DeltaG(ps) are much less negative. The weaker interactions of C(12)C(12)C(12)Br(2) with HMPAMs arise from the marked reduction of attraction between surfactant headgroups and polymer hydrophilic groups induced by its longer spacer.     

疏水改性聚丙烯酰胺溶液的分子模拟

设计了几种不同的非离子型改性聚丙烯酰胺(HM-PAM)和阴离子型改性聚丙烯酰胺(HM-HPAM). 通过分子动力学模拟(MD)方法研究了在聚合物链上加入不同疏水改性单体对提高聚丙烯酰胺耐盐性的影响, 考察了盐浓度对疏水改性聚丙烯酰胺的回旋半径(R_g)、 特性黏数([η])、 径向分布函数(RDF)和均方位移(MSD)的影响以及聚合物的微观结构与特性黏数之间的关系. 研究结果表明, 引入疏水改性单体后, 改性聚丙烯酰胺具有较好的耐盐性. 通过研究非键作用与氢键相互作用可知, 体系中溶质和溶剂间的相互作用及氢键作用越弱, 溶液的特性黏数越大. O-H原子对的RDF结果表明, 聚合物链的伸展与聚合物链及官能团间的相互作用有关. 当RDF峰较弱时, 聚合物链与水的作用越弱, 越有利于聚合物链保持舒展状态, 溶液的特性黏数也就越大. 另外, 从聚合物链的MSD曲线发现, 聚合链的移动性与特性黏数呈负相关.     

A steady‐state mass balance model of the polycarbonate–CO2 system reveals a self‐regulating cell growth mechanism in the solid‐state microcellular process

A simple mechanism regulating polymer mobility is demonstrated to determine initial and final growth states of solid‐state microcellular foams. This mechanism, governed by the extent of plasticization of the polymer by the dissolved gases, is examined with a mass balance model and results from foam growth experiments. Polycarbonate was exposed to CO₂, which acted as both a plasticizing gas and a physical blowing agent driving foam growth. The polycarbonate specimens were saturated to the equilibrium gas concentration at 25 °C for CO₂ pressures of 1–6 MPa in 1‐MPa increments. Equilibrated specimens were heated in a glycerin bath until thermal equilibrium was reached, and a steady foam structure was attained. Glycerin bath temperatures of 30–150 °C in 10 °C increments were examined. Using knowledge of gas solubility, the equation of state for CO₂, the effective glass‐transition temperature as a function of gas concentration, and a model for mass balance within a solid‐state foam, we demonstrate that foam growth terminates when sufficient gas is driven from the polycarbonate matrix into the foam cells. The foam cell walls freeze at the elevated bath temperature because of gas transport from the polycarbonate matrix and the associated rise in the polymer glass‐transition temperature to that of the heated bath. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 868–880, 2001