纳米氧化锌光催化降解有机染料性能的研究

用自制的纳米ZnO在室外阴天、太阳光照射、室内紫外灯照射等条件下对不同有机染料的降解性能作了系统的研究。结果表明纳米ZnO在太阳光照射条件下对弱碱性有机染料溶液的降解效果较好。本文还比较了自制纳米ZnO与纳米TiO2对有机染料的降解性能，结果表明ZnO的降解效果优于TiO2。     

Accelerated ZnMoO4 photocatalytic degradation of pirimicarb under UV light mediated by peroxymonosulfate

This paper reports the optimized synthesis of zinc molybdates by the hydrothermal method and the combination of ZnMoO₄ and peroxymonosulfate (PMS) under UV irradiation for the degradation of pirimicarb. The as‐prepared ZnMoO₄ photocatalyst was characterized using X‐ray diffraction, scanning electron microscopy, X‐ray photoelectron spectroscopy and UV–visible diffuse reflectance spectroscopy. The effects of operational parameters in the ZnMoO₄/PMS/UV system were evaluated and the results indicated the highest performance is achieved with pH = 9.0, 1 mM PMS and 1 g l^?1 ZnMoO₄. The degradation efficiency of pirimicarb was 98% after 3 h in the photocatalytic process. A photodegradation mechanism is proposed based on scavenger and electron spin resonance studies to decide the main active species and by using chromatography–mass spectrometry to identify the major intermediates. Pirimicarb degradation is found to be mainly driven by holes and ?O₂^? radicals, with the contribution of ?OH and SO₄^?? radicals enhancing the process in the tested catalytic system. The mechanism is proposed involving two routes, dealkylation and decarbamoylation. Lastly, the zinc molybdate photocatalyst is shown to be stable, reusable and efficient in the removal of pirimicarb from real water samples in the presence of PMS, demonstrating potential application in the treatment of contaminated and/or environmental water.     

Preparation of Mn-doped ZnO nanostructured for photocatalytic degradation of Orange G under solar light

Research on Chemical Intermediates - In this study, undoped ZnO and Mn-doped ZnO nanostructured with different doping concentrations were prepared through a facile chemical method. Then, X-ray...     

Nanotheranostic fabrication of iron oxide for rapid photocatalytic degradation of organic dyes and antifungal potential

This research work includes the fabrication of iron oxide nanoparticles (Fe₂O₃ NPs) by green construction approach using Wisteria sinensis leaves extract. Due to its eco-friendly approach, the synthesis of iron oxide NPs (Fe₂O₃ NPs) using various plant sources, such as plant parts, and microbial cells have gained a lot of attention in recent years. Cost-effectiveness and ease of availability make Wisteria sinensis leaves extract a potential candidate for the construction of iron oxide NPs. The various key features like biocompatibility, non-toxicity capping, and stabilizing agents present in biological sources are advantageous for usage in a variety of applications. The phytoconstituents present in the leaf extract of Wisteria sinensis serve as reducing and stabilizing agents. The biologically fabricated (Fe₂O₃ NPs) were analyzed using FT-IR, XRD, UV–vis spectroscopy, and SEM. In the present work, the antioxidant and photocatalytic dye degradation efficiency of Fe₂O₃ NPs has been studied. The dye degradation efficiency of methylene blue dye was found to be 87% at 180 min upon exposure to sunlight. The capacity of Fe₂O₃ NPs to scavenge 2,2-diphenyl-1-picrylhydrazyl hydrate free radicals (DPPH) was examined using a UV–Vis spectrophotometer. The study compared the radical scavenging activity (RSA) of Fe₂O₃ nanoparticles (NPs) with that of the standard antioxidant ascorbic acid. The results demonstrated that Fe₂O₃ NPs have a greater ability to scavenge radicals than ascorbic acid. The half-maximal inhibitory concentration (IC50) of Fe₂O₃ NPs was observed to range from 0.12 to 0.17. Furthermore, Fe₂O₃ NPs displayed the highest antifungal activity, with an inhibition zone of 26.8 mm against F. oxysporum. These findings suggest that the biologically synthesized Fe₂O₃ NPs possess potent antimicrobial and dye degradation properties.     

Kinetics of heterogeneous photocatalytic degradation of reactive dyes in an immobilized TiO2 photocatalytic reactor

The photocatalytic degradation of two reactive dyes has been investigated by UV/TiO2/H2O2 using an immobilized TiO2 photocatalytic reactor. Reactive Blue 8 (RB 8) and Reactive Blue 220 (RB 220) textile dyes were used as model compounds. Photocatalytic degradation processes were performed using a 5-L solution containing dyes. The initial concentrations of dyes were 50 mg/L. The radiation source was two 15 W UV-C lamps. A batch mode immersion photocatalytic reactor was utilized. UV-vis and ion chromatography (IC) analyses were employed to obtain the details of the photodegradation of the selected dyes. Colored synthetic waters were completely decolorized in relatively short time after UV irradiation in the presence of various concentrations of hydrogen peroxide. Formate, acetate, oxalate, and glyoxylate anions were detected as dominant aliphatic intermediates where they were further oxidized slowly to CO2. The UV/TiO2/H2O2 process was able to oxidize the dyes with partial mineralization of carbon, nitrogen, and sulfur heteroatoms into CO2, NO3-, and SO4(2-), respectively. Kinetics analysis indicates that the photocatalytic decolorization rates of the dye can be approximated by a pseudo-first-order model. The UV/TiO2/H2O2 process proved to be capable of decolorization and mineralization of the reactive dyes (RB 8 and RB 220).     

A novel approach for the oxidative degradation of organic pollutants in aqueous solutions mediated by iron tetrasulfophthalocyanine under visible light radiation

An efficient approach has been developed to decompose toxic organic pollutants. The photodegradation of Rhodamine B (RhB), salicylic acid, and Orange II was examined in the presence of iron tetrasulfophthalocyanine ([Fe(PcS)]) and H(2)O(2) under visible irradiation. It was found that under visible light irradiation, organic pollutants in the [Fe(PcS)]/H(2)O(2) system can be rapidly degraded, but the concentration of [Fe(PcS)] remains nearly unchanged, and this indicates that [Fe(PcS)] has a good catalytic character. EPR results and other experimental results suggest that the light-activated reaction process involves the formation and reaction of HO(.) radicals. On the basis of the experimental results, a possible reaction mechanism for the degradation of organic pollutants under visible light illumination in the aqueous [Fe(PcS)]/H(2)O(2) solutions is proposed.     

Facile synthesis of quantum dots metal oxide for photocatalytic degradation of organic hazardous materials and factory effluents

Solar photocatalytic behavior of zinc oxide quantum dots (ZQs) was studied and synthesized using a modified precipitation process and characterized using various spectroscopic techniques. HRTEM was used to demonstrate and verify the purity of the prepared quantum dot material and the calculated crystallite size is 4.4 and 5.3 nm for the ZQ1 and ZQ2 samples, respectively. The optical characteristics and the BET analysis of ZQs samples investigated great value for the bandgap energy and the specific surface for ZQS samples. The photodegradation process of Indigo Carmine dye (IC) (one of the commercial organic hazardous materials used in the dying process) by ZQ1 recorded the highest synthetic levels equal to 17.18 × 10^-3S^-1. Also, the ZQ1 sample with the smallest particle size reaches the maximum fluorescence rate by almost 31 % in coumarin photo-oxidation than the ZQ2 sample with the largest particle size. This study included a report of the mineralization of IC dye, 16 investigated factory effluents samples, and their recovery ability for ten replication cycles as a case study in the presence of ZQs by sunlight for two months. These evaluation processes are by TOC analysis and COD measurements.     

Microplasma-assisted synthesis of CuO nanostructures for catalytic degradation of organic dyes under solar irradiation

Journal of Solid State Electrochemistry - In this research work, CuO nanostructures were synthesized using atmospheric pressure microplasma (AMP) electrochemical process. The synthesized CuO...     

Photocatalytic degradation of chlorophenols under direct solar radiation in the presence of ZnO catalyst

The photocatalytic degradation of chlorophenols was evaluated under direct solar radiation using commercial ZnO catalyst. Effects of several parameters such as a catalyst loading, pH of solution and initial concentration on the degradation process have been investigated. The photocatalytic degradation efficiency of chlorophenols at the optimum value of the parameters was compared under similar experimental conditions. The results of efficiency and mineralization showed the degradation of 2-chlorophenol and 2,4-dichlorophenol compound with the first order kinetic rate and the rate constant decreases as the initial concentration of the chlorophenols increase. However, the rate constant was strongly affected by type of chlorophenols compound present either 2-chlorophenol or 2,4-dichlorophenol. The highest removal of chlorophenols was obtained after 120 min and the final intermediate compounds of chlorophenols degradation are lower molecular weight compound consisting of acetic acid which was analyzed through the HPLC.     

Efficient degradation of organic pollutants mediated by immobilized iron tetrasulfophthalocyanine under visible light irradiation

Supported iron tetrasulfophthalocyanine can efficiently catalyze the degradation of organic pollutants by H2O2 under visible light irradiation in an aqueous solution, and the catalyst can be easily recycled without apparent loss of activity.     

Engineering covalent organic frameworks in the modulation of photocatalytic degradation of pollutants under visible light conditions

Mixtures of triphenylamine (TPA) and phenyl phenothiazine (PTH) fragments have been incorporated into a series of extended polyimine structures that have been applied in the photodegradation of pollutants of different nature under visible light irradiation. Results obtained revealed that materials containing PTH as the sole photoactive unit resulted in the most active photocatalytic material in the degradation of polybrominated diphenyl ether-1 and Sudan Red III. In contrast, the covalent organic framework containing only TPA acted as the best photocatalyst for the degradation of Methylene Blue. These different trends are related to the versatility of PTH moiety to trigger both photoredox and energy transfer processes, while TPA is only an effective energy transfer catalyst.     

Chalcogen-doped zinc oxide nanoparticles for photocatalytic degradation of Rhodamine B under the irradiation of ultraviolet light

In the present work, the chalcogen (Se²⁺)-doped ZnO nanoparticles (SeZO-NPs) were synthesized using sol-gel precipitation method and tested for photocatalytic degradation of Rhodamine B (RhB). X-ray diffraction pattern of SeZO-NPs showed the hexagonal wurtzite crystal structure regardless of Se concentration. The band edge and defect-level emissions of SeZO-NPs were determined by using the photoluminescence spectra with the excitation source of 370 nm. The bandgap, E_g, of SeZO-NPs was measured from diffused reflectance spectroscopy, which increased from 3.22 to 3.26 eV as Se concentration increased from 0 to 10 wt.%. The highest specific surface area and lowest pore size of 5-SeZO-NPs were observed to be 36.42 m²/g and 13.48 nm, respectively. The photocatalytic degradation of SeZO-NPs was measured under the illumination of ultraviolet (UV) light. The double donor (Se) played an important role toward photodegradation of RhB via reducing the recombination of charge carriers. The highest photocatalytic degradation (98.23%) and mineralization were achieved for the sample 5-SeZO (Se: 5 wt.%). The improved photocatalytic performance of 5-SeZO was attributed to the optimum Se dopant concentration for the production of more reactive oxygen species because of effective separation of charge carriers in UV light.     

几种典型有毒有机污染物的光催化降解研究

本文研究了氯代苯酚和苯胺类化合物的光催化降解,探讨了这些有机污染物分子的氯取代和化合物毒性与光催化降解之间的关系.研究表明,氯代苯酚和苯胺类化合物的光催化降解均符合表观一级反应动力学模型.有机物分子中氯取代基的引入加快了化合物的光催化降解,且反应速率随氯取代基个数的增多而增大.光催化降解的表观速率常数与正辛醇-水分配系数之间存在有较好的线性关系:logk=alogKow+b,该模型可以用于有机污染物的光催化降解性预测.     

Enhancement of 2-chlorophenol photocatalytic degradation in the presence Co<Superscript>2+</Superscript>-doped ZnO nanoparticles under direct solar radiation

The performance of Co²⁺-doped ZnO nanoparticles, prepared using the sol–gel method, for 2-chlorophenol degradation under direct solar radiation was investigated. Various parameters were investigated during the degradation process, namely solar intensity, Co²⁺ ion concentration, loading concentrations of Co²⁺-doped ZnO, and pH. The photocatalytic degradation efficiency increased when the initial concentration of 2-chlorophenol decreased; the optimum concentration was 50 mg/L under similar experimental conditions. Moreover, optimum values, established on a sunny day, were 0.75 wt% of Co²⁺, a 1 g/L loading concentration, and a pH of 6.0, respectively. The highest degradation efficiency observed was 95 %, after only 90 min of solar light irradiation. The mechanism of visible photocatalytic degradation using Co²⁺-doped ZnO was explained as a strong electronic interaction between Co²⁺, Co³⁺ and ZnO, and a promotion in the charge separation, which enhanced the degradation performance. The fragmentation of 2-chlorophenol under the optimal conditions was investigated using HPLC, comparing standards of all intermediate compounds. The pathway of the fragmentation was proposed as involving hydroxyhydroquinone, catechol, and phenol formation, which were then converted to non-toxic compounds such as oxalic acid and acetic acid with further decomposition to CO₂ and H₂O.     

The effect of dosage on the photocatalytic degradation of organic pollutants

Heterogeneous photocatalytic degradation of many organic pollutants, such as phenol and phenol derivatives, may be optimised if the catalyst surface saturation and the appearance and accumulation of non-photocatalytically degradable intermediates is avoided. It has been shown that under certain concentration threshold the highest degradation efficiencies are achieved. Over these concentrations, degradation rates become constant owing to the limited catalyst surface. By the dosage of the contaminant, currently in an aqueous solution, the process may be optimised, thus avoiding the formation of inert intermediates which may be more toxic than the parental compound. The effect of dosage on the photocatalytic degradation of phenol and phenol derivatives, such as salicylic acid and 4-aminophenol has been studied. Comparatively notably higher efficiencies have been obtained compared to those of the high initial single dose experiments (non-dosage), for which high initial concentrations of the organics resulted in the catalysts poisoning. Degussa P-25 and its combination with 13% (w/w) activated carbon, namely AC?TiO₂, have been used as catalysts. Almost complete degradations are achieved at low dosage rates (1–2 pmm/min). At higher dosage rates, different processes such as catalyst poisoning predominate, resulting in lower degradation efficiencies.     

Photolytic and photocatalytic degradation of organic UV filters in contaminated water

UV filters as emerging contaminants are of great concern and their wide detection in aquatic environments indicates their chemical stability and persistence. This review summarized the photolytic and photocatalytic degradation of UV filters in contaminated water. The findings indicated that limited research has been conducted on the photolysis and photocatalysis of UV filters. Photolysis of UV filters through UV irradiation in natural water was a slow process, which was accelerated by the presence of photosensitisers e.g. triplet state of chromaphoric dissolved organic matter (³CDOM*) and nutrients but reduced by salinity, dissolved organic matter (DOM) and divalent cations. UV Photocatalysis of 4-methylbenzylidene camphor and 2-phenylbenzimidazole-5-sulfonic acid was very effective with 100% removal within 30 min and 90 min using medicated TiO₂/H₂O₂ and TiO₂, respectively. The radiation source, type of catalyst and oxygen content were key factors. Future research should focus on improved understanding of photodegradation pathways and by-products of UV filters.