35 GPa斜波加载下RDX单晶炸药的动力学行为

利用磁驱动斜波加载10 MA装置和激光干涉测速技术,开展了35 GPa压力下(100)晶向RDX单晶炸药的斜波压缩实验,获得了RDX单晶/LiF单晶窗口界面速度数据。实验结果显示,速度波剖面表现为明显的三波结构,由低到高依次对应弹性波、塑性波和相变波,α-γ相变的起始压力为3.1 GPa。结合修正的多相状态方程和非平衡相变动力学模型,对RDX单晶炸药的斜波压缩过程开展一维流体动力学数值模拟,模拟结果与实验结果基本一致。     

固体炸药的磁驱动准等熵压缩实验研究

较宽压力范围内未反应炸药的本构关系和状态方程对于深入和精确认识压缩波作用下炸药组分间相互作用的力学过程和起爆热点的形成机制具有重要意义。较之冲击压缩,磁驱动准等熵压缩加载(无冲击压缩)是获取较宽压力范围内未反应炸药的动态压缩力学特性更有效的手段。基于大电流产生的电磁力作用原理,在国内率先实现了炸药的磁驱动无冲击压缩实验技术。通过对负载电极、炸药样品参数的优化设计和安装工艺的控制,实现了5 GPa载荷内JO-9159炸药的磁驱动准等熵压缩加载。基于激光位移干涉测量技术和Lagrange数据处理方法,获得了JO-9159炸药的速度响应历史和准等熵压缩线。所得结果与文献数据进行了比较,结果表明,在实验压力范围内,JO-9159炸药的等熵压缩线与PBX9501炸药的等熵压缩线一致。     

准等熵压缩下氟橡胶F_(2311)的动力学行为实验研究

利用磁驱动准等熵压缩实验技术,对常用固体炸药粘结剂氟橡胶F2311在准等熵压缩加载下的动力学响应特性进行了实验研究。利用激光干涉测速技术,获得了加载峰值压力7GPa内3种不同厚度F2311样品/PMMA(有机玻璃)窗口界面速度响应曲线。利用Lagrange方法和反积分方法对速度历史进行了处理,获得了F2311在该压力范围内的力学特征。研究结果表明:在0~3.5GPa之间,氟橡胶F2311的动力学行为可用一阶形式的us-up关系us=1.89+3.84up描述;在3.5~7.0GPa之间,则表现出明显的非线性行为。     

斜波压缩下锡的相变动力学特性

利用磁驱动加载装置(CQ-4)和高精度速度测试装置(DPV),开展了斜波加载下锡的动态压缩实验。实验结果表明:锡在加载阶段经历了弹塑性转变和相变等物理过程,相变压力约为7.5 GPa。β–γ相变对应的特征速度随着锡厚度的增加,从676.3 m/s减小到636.8 m/s,对应的压力从7.62 GPa降低到7.11 GPa。结合Hayes多相状态方程和非平衡相变动力学模型,对锡的斜波压缩实验过程进行了模拟,数值计算结果可以较好地描述锡在加载阶段的弹塑性转变和相变等物理过程。讨论了体模量在不同热力学过程中的物理形式,计算结果显示,斜波压缩过程需考虑压力对体模量的修正。分析了相变弛豫时间、体模量等典型物理参数对速度波形的影响,结果表明,相变弛豫时间和各相初始自由能主要影响混合区部分速度波形,γ相的体模量参数只影响相变后的速度波形,β相的体模量参数会影响整体速度波形。     

利用电磁法研究HMX与TATB混合钝感炸药的冲击起爆特性

为研究含有少量奥克托金(HMX)且以三氨基三硝基苯(TATB)为基的高能钝感炸药PBX-3的冲击起爆反应增长规律,采用火炮驱动蓝宝石飞片的方法和铝基组合式电磁粒子速度计技术进行了一维平面冲击实验。通过实验测量撞击表面及内部不同深度处的冲击波后粒子速度,得到PBX-3炸药的Hugoniot关系。根据冲击波示踪器所测数据绘制了炸药到爆轰的时间-距离(x-t)图,获得了反映炸药冲击起爆性能的Pop关系。将入射压力为12.964 GPa时达到爆轰的6条速度曲线修整成相同零点,通过读取6条曲线的分离点即反应区末端的C-J点,计算出化学反应区时间和宽度。     

窗口声阻抗对锆相变动力学的影响

基于磁驱动加载装置CQ-4开展了锆的斜波压缩相变实验,研究了锆样品后表面窗口声阻抗对相变波形的影响.实验结果显示,锆后表面为较低声阻抗窗口(自由面和LiF窗口)时,相变起始对应的特征粒子速度约331.0 m/s,而高阻抗蓝宝石窗口时,特征粒子速度约301.9 m/s,特征速度对应的压力从约9.14 GPa下降到8.27 GPa.相变对应的速度特征拐点是与多种因素相关的实验信息,因此它对应的压力并不是材料属性参数相变压力.结合基于热力学Helmholtz自由能的多相状态方程和非平衡相变动力学方程开展了锆的相变动力学数值模拟研究,相变弛豫时间为30 ns,计算结果与三种情况的实验结果符合良好,可以较好地模拟斜波压缩下锆的弹塑性转变、相变等物理过程.在压力-比容和温度-压力热力学平面,相变前锆的准等熵线与冲击绝热线差异很小,相变后准等熵线都位于冲击绝热线下方,随着压力的增加准等熵线和冲击绝线偏差越来越大,温度-压力平面中在20 GPa时相差约100 K.相变开始后,由于相变引起比容的间断,导致锆的拉氏声速迅速下降约7%,相变完成后拉氏声速恢复到体波声速.     

一种同步研究透明材料折射率和动力学特性的实验方法

基于电磁加载装置CQ-4,建立了一种同步开展透明材料折射率和高压声速测量的实验方法.完成了聚甲基丙烯酸甲酯(PMMA)窗口材料14 GPa斜波压缩实验,利用多点双光源外差位移干涉测速仪(dual laser heterodyne velocimetry, DLHV),获得了PMMA样品后表面的速度历史曲线.速度曲线表现出明显的双波结构,表明PMMA样品出现了弹塑性转变.通过实验数据处理,一发实验同步获取了PMMA的折射率-粒子速度光学特性和拉氏声速-粒子速度动力学特性.     

电磁驱动45钢准等熵压缩的实验研究

在已有的众多准等熵加载技术中,磁驱动准等熵加载技术具有准等熵程度高、压力范围大、实验材料种类多、效费比高等特点。利用中物院流体物理研究所建成的磁驱动准等熵压缩和高速飞片实验装置CQ-1.5(最高加载压力为50GPa),成功开展了45钢的准等熵压缩实验,对装置的主要参数进行了介绍;利用激光干涉测试系统DPS获得了45钢飞片的自由面速度历史,通过反积分处理给出了材料准等熵压缩的p-V关系。通过分析实验数据,获得了45钢3种形式的等熵方程的参数。实验获得的最高等熵压力为47.5GPa。     

超压爆轰产物声速以及热力学CJ点的实验研究

超压爆轰产物声速是建立超压爆轰产物状态方程的基础性实验数据,而CJ点数据是反映炸药爆轰性能的重要参数。利用稀疏波追赶技术,通过光纤探针监测三氯甲烷中稀疏波追赶向前冲击波的过程,测量了不同压力点下JB-9014炸药超压爆轰产物的声速,得到了拉格朗日声速随粒子速度的变化曲线,由Lc线与稳定爆速D的交点确定了热力学CJ点,对JB-9014炸药所得到的CJ压力为28.8 GPa,与通常测量值28.5 GPa仅相差0.3 GPa。介绍了应用光纤探针测量爆轰驱动飞片的速度和平面性的方法,应用该方法得到了飞片的击靶速度和形状,此方法具有较高的测量精度。     

镁铝合金的冲击熔化行为实验研究

采用反向碰撞实验技术,结合具有高时空分辨率的全光纤激光干涉测速技术,对镁铝合金开展了极端动态压缩条件下的动力学行为实验研究,获得了镁铝合金在30～73 GPa压力范围内的Hugoniot和声速实验数据。深入的数据分析表明,所获得的Hugoniot数据与早期的Hugoniot数据一致,但是纵波声速却呈现出明显的向体波声速转变的趋势,对应冲击加载下镁铝合金的固-液熔化相变,相变压力区间为40～57 GPa。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.