基底对电沉积制备ZnO纳米棒阵列的影响

采用恒电位电沉积方法, 在未经修饰的ITO导电玻璃基底上通过控制实验条件制备出不同形貌的纳米ZnO结构, 而在经过ZnO纳米粒子膜修饰后的ITO导电玻璃基底上, 制备出透明、高取向、粒径小于30 nm的ZnO纳米棒阵列. 用扫描电子显微镜(SEM)、X射线衍射(XRD)以及透射光谱对制备出的ZnO纳米棒阵列的结构、形貌和透明性进行了表征. 测试结果表明, ZnO纳米棒阵列的平均直径为21 nm, 粒径分布窄, 约18～25 nm, 择优生长取向为[001]方向, 垂直于基底生长. 当入射光波长大于400 nm时, ZnO纳米棒阵列的透光率大于95%.     

电化学沉积法制备金（核）-铜（壳）纳米粒子阵列

以组装在有机分子自组装膜/金基底电极上的Au纳米粒子阵列为电化学沉积模板,制备了金(核)-铜 (壳)纳米粒子阵列.选用巯基十一胺（AUDT）和巯基癸烷（DT）混合自组装膜作为基底电极与Au纳米粒子的耦联层,可以在一定的电位下实现金属Cu在Au纳米粒子上的选择性沉积.将沉积电位控制在－0.03 V（vs SCE）时,沉积初期（t ≤ 15 s,沉积粒子粒径 ≤ 20 nm ）金(核)-铜 (壳)粒子具有良好的单分散性和近似球形,而且粒径实验值同计算值非常吻合.     

介孔SiO_2薄膜增敏SERS基底在消逝波激励下的特性表征

采用溶胶-凝胶分子模板法在50 nm厚金膜表面制备约40 nm厚介孔二氧化硅(MPS)薄膜,然后在MPS薄膜表面静电自组装金纳米粒子(GNP)单层膜,形成的多层膜结构用作表面增强拉曼散射(SERS)基底.利用扫描电镜观测到MPS薄膜具有表面开口多孔结构,有助于小分子向薄膜内快速扩散.基于时域有限差分(FDTD)方法对电场分布的仿真结果指出,在表面等离子体共振(SPR)条件下分布于金膜与GNP之间的消逝场显著增强.由于空间重叠,该增强场能够高效激发MPS内富集的小分子拉曼信号,产生的拉曼信号还可免受金属作用的干扰.利用Kretschmann结构和尼罗蓝(NB)拉曼活性分子测试了Au/MPS/GNP基底在785 nm激发波长下的SERS效果,并与Au/GNP基底进行了比较.结果表明,在SPR条件下,Au/MPS/GNP基底能够导致较强的定向和背向拉曼信号,而且在586 cm-1处的背向拉曼信号强度是Au/GNP基底的40倍,这归功于MPS薄膜.进一步测试表明背向拉曼信号强度与NB浓度成正相关.这意味着Au/MPS/GNP基底具有良好的半定量检测本领.     

介孔SiO2薄膜增敏SERS基底在消逝波激励下的特性表征

采用溶胶-凝胶分子模板法在50 nm 厚金膜表面制备约40 nm 厚介孔二氧化硅(MPS)薄膜, 然后在MPS薄膜表面静电自组装金纳米粒子(GNP)单层膜, 形成的多层膜结构用作表面增强拉曼散射(SERS)基底.利用扫描电镜观测到MPS薄膜具有表面开口多孔结构, 有助于小分子向薄膜内快速扩散. 基于时域有限差分(FDTD)方法对电场分布的仿真结果指出, 在表面等离子体共振(SPR)条件下分布于金膜与GNP之间的消逝场显著增强. 由于空间重叠, 该增强场能够高效激发MPS内富集的小分子拉曼信号, 产生的拉曼信号还可免受金属作用的干扰. 利用Kretschmann 结构和尼罗蓝(NB)拉曼活性分子测试了Au/MPS/GNP基底在785 nm激发波长下的SERS效果, 并与Au/GNP基底进行了比较. 结果表明, 在SPR条件下, Au/MPS/GNP基底能够导致较强的定向和背向拉曼信号, 而且在586 cm^-1处的背向拉曼信号强度是Au/GNP基底的40 倍, 这归功于MPS薄膜. 进一步测试表明背向拉曼信号强度与NB浓度成正相关. 这意味着Au/MPS/GNP基底具有良好的半定量检测本领.     

聚共轭亚油酸基网状纳米金的制备及表面增强拉曼散射和催化性能

以天然不饱和脂肪酸共轭亚油酸(CLA)为绿色单体, 通过简单的分子自组装和可控自交联反应制备聚共轭亚油酸(PCLA)聚集体. 透射电子显微镜(TEM)结果显示, PCLA聚集体的形貌呈现独特网状结构, 其联结单元为来自于CLA胶束的膨大颗粒. 采用氯金酸在极性聚合物表面原位还原, 2 d后在网状PCLA基底上制备得到以CLA胶束为核(20 nm)的网状纳米金结构, 而且网状PCLA的原位还原作用与模板作用相结合是获得PCLA基网状纳米金的充分必要条件. 与普通球形胶态金纳米颗粒[(5±1) nm]相比, PCLA基网状纳米金对苯硫酚具有更好的表面增强拉曼散射(SERS)效应, 对对硝基苯酚具有更好的催化还原效果.     

组装在贵金属基底上的金纳米粒子对CO的电化学催化氧化

研究了组装在Au, Pt电极表面的金纳米粒子对CO的电化学催化氧化行为, 首次在实验上观察到较大粒径金纳米粒子(粒径＞10 nm)对CO的电催化氧化活性. 考察了金粒子表面金氧化物对粒子电催化活性的影响, 发现表面金氧化物的形成是金纳米粒子对CO具有电催化氧化活性的前提. 对于相同粒径的金纳米粒子, 随着粒子表面金氧化物量的增加,催化活性增大.     

金纳米球和金纳米棒的制备及其光热催化性能

以氯金酸(HAuCl_4)为原料,硼氢化钠(NaBH_4)为还原剂,聚乙烯吡咯烷酮K30(PVP)为稳定剂制备了尺寸5 nm的金纳米球;以阳离子表面活性剂十六烷基三甲基溴化铵(CTAB)为模板剂和油酸钠(NaOL)稳定剂,用种子生长法制备了不同长径比(R=2.5~4)的金纳米棒。在2 W·cm~(-2)的808 nm激光照射10 min条件下,C(0.4 mg·mL~(-1))浓度金纳米球溶液升温10.2℃,该溶液可催化血液中亚硝基硫醇释放NO,最大释放量可达1.42 nmol·L~(-1);相同光热及催化条件下,C(0.4 mg·mL~(-1))浓度金纳米棒(R=3.01)溶液升温41.3℃,该溶液催化血液中亚硝基硫醇释放NO最大释放量可达1.89 nmol·L~(-1)。金纳米球和金纳米棒的光热及催化性能随着浓度增加而增强,金纳米棒的光热及催化性能要优于金纳米球。     

纳米金颗粒增强信号的表面等离子体共振生物传感器用于甲氧檗因高灵敏检测的研究

报道了一种基于表面等离子体共振(SPR)生物传感器的高灵敏检测抗癌药物甲氧檗因的新方法. 分别在纳米金颗粒和金膜表面修饰富含腺嘌呤(A)的DNA链, 当存在甲氧檗因时, 由于一个甲氧檗因分子可与4个A碱基相结合, 从而使得修饰在纳米金颗粒和金膜表面的DNA形成稳定的双链结构, 进而将功能化纳米金颗粒捕获在金膜表面. 由于纳米金颗粒与金膜之间的电场耦合效应可增强SPR信号, 从而可实现对小分子甲氧檗因的高灵敏、特异性检测. 本方法的检测下限低至0.07 pmol/L, 相对比色法和荧光法而言, 降低了约5～6个数量级. 以4种药物(盐酸小檗碱、青霉素G、硫酸庆大霉素、5-氟尿嘧啶)作为对照考察了该传感器的选择性, 结果表明该传感器具有较好的选择性.     

纳米多孔金薄膜的表面等离子体共振传感特性

对淀积在玻璃衬底上厚度约60 nm的金银合金溅射薄膜进行硝酸腐蚀脱银处理, 得到纳米多孔金薄膜. 利用自建的波长检测型表面等离子体共振(SPR)传感装置研究了腐蚀时间对纳米多孔金薄膜SPR特性的影响, 结果发现纳米多孔金薄膜与水溶液接触后在400-900 nm光谱范围内不具有SPR效应, 而当薄膜置于空气中时会产生明显的传播等离子体共振吸收峰, 其共振波长随腐蚀时间增加逐渐红移. 纳米多孔金薄膜在空气气氛中的SPR效应使其能够用于原位监测气相分子在孔内的吸附, 还可对在液相中吸附的生化分子进行离位测试. 本文对L-谷胱甘肽、L-半胱氨酸、2-氨基乙硫醇三种含巯基的生化小分子在纳米多孔金薄膜内的吸附进行了离位分析, 结果表明与传统的致密金薄膜SPR芯片比较, 纳米多孔金薄膜对这些分子显示出更高的灵敏度和更低的检测下限, 这归功于多孔金的大比表面积使其能够吸附大量的生化小分子. 实验还对乙醇蒸气在纳米多孔金薄膜内的吸附进行了原位监测, 发现吸附平衡所用时间较长, 约为160 min.     

云母表面金纳米颗粒单层膜的制备

近年来 ,随着纳米科技的兴起 ,纳米尺度的金颗粒以其独特的光学和电学性质在许多领域表现出潜在的应用价值 ,引起人们浓厚的研究兴趣 .金纳米颗粒单层膜在表面增强拉曼基底及纳米刻蚀等方面有着广泛的应用 [1,2 ] .以往人们多用双官能团硅烷化试剂对硅氧化物基底 ,如玻璃和石英等进行表面修饰 ,获得氨基、巯基或氰基等修饰的表面 ,再利用金纳米颗粒与上述功能团之间的化学相互作用 ,来制备金纳米颗粒单层膜 [3,4 ] .Fig.1　 Crystal structure of muscovite mica云母为层状结构的硅铝酸钾 (晶体结构示于图 1 ) ,表层为 0 0 0 1晶面 ,K+ 离…     

Fabrication of SPR Nanosensor Using Gold Nanoparticles and Self-Assembled Monolayer Technique for Detection of Cu2+ in an Aqueous Solution

In this work, we investigated the fabrication of surface plasmon resonance (SPR) nanosensor using gold nanoparticles (AuNPs) chemisorbed onto self assembled monolayer of 10-(3-amino phenoxy) decane-1-thiol on gold substrate. The fabrication process of SPR nanosensor was characterized using different techniques such as infrared reflection-absorption spectra (IRRAS), xX-ray photoelectron spectroscopy (XPS), and atomic force microscope (AFM). The fabricated SPR nanosensor was used for detection of Cu²⁺ in an aqueous solution using surface plasmon resonance refractometer. The results confirm the fabrication of new SPR nanosensor. The fabricated SPR nanosensor showed a good activity toward the detection of Cu²⁺. The detection of Cu²⁺ in an aqueous solution using the fabricated SPR nansensor was enhanced in the presence of gold nanoparticles.     

Determination of thickness, dielectric constant of thiol films, and kinetics of adsorption using surface plasmon resonance

This paper describes the formation of a self-assembled monolayer of 11-mercaptoundecanoic acid (MUA) under different concentrations on a gold sensor disk, monitoring in situ and in real time using surface plasmon resonance spectroscopy (SPR). The film thickness and dielectric constant were determined for a fully formed monolayer using one-color approach SPR. The kinetic studies of the film formation in ethanol solution indicated that the self-assembled monolayer is formed in a two-step adsorption process. In this sense, this unpublished route was applied on the basis of a model where many molecules are adsorbed at an initial step and then can be desorbed and/or rearranged to form a perfect monolayer.     

AuAg bimetallic nanoparticles film fabricated based on H2O2-mediated silver reduction and its application

A method to fabricate AuAg bimetallic nanoparticles film by H₂O₂-mediated reduction of silver was reported. Gold nanoparticles (Au NPs) were first adsorbed onto the surface of a self-assembled 2-aminoethanethiol monolayer-modified gold film or 3-aminopropyltriethoxysilane (APTES) monolayer-modified quartz slide. Upon further treatment of this modified film with the solution containing silver nitrate (AgNO₃) and H₂O₂, silver was deposited on the surface of Au NPs. The size of the AuAg bimetallic particles could be readily tuned by manipulating the concentration of H₂O₂. Surface plasmon resonance (SPR) was used to investigate the process, the deposition of silver on Au NPs modified gold film resulted in an obvious decrease of depth in the SPR reflectance intensity and minimum angle curves (SPR R-θ curves), which may be utilized for the quantitative SPR detection of the analyte, H₂O₂. Combination of the biocatalytic reaction that could yield H₂O₂ by using the enzyme, glucose oxidase, with the deposition of silver may enable the design of a glucose biosensor by SPR technique. Furthermore, we evaluated the AuAg bimetallic nanoparticles film for their ability to be an effective substrate for surface-enhanced Raman scattering (SERS).     

Au NPs-aptamer conjugates as a powerful competitive reagent for ultrasensitive detection of small molecules by surface plasmon resonance spectroscopy

Features of Au NPs-aptamer conjugates as a powerful competitive reagent to substitute antibody in enhancing surface plasmon resonance spectroscopy (SPR) signal for the detection of small molecule are explored for the first time. In order to evaluate the sensing ability of Au NPs-aptamer conjugates as a competitive reagent, a novel SPR sensor based on indirect competitive inhibition assay (ICIA) for the detection of adenosine is constructed by employing the competitive reaction between antiadenosine aptamer with adenosine and antiadenosine aptamer with its partial complementary ss-DNA. The partial complementary ss-DNA of antiadenosine aptamer is firstly immobilized on SPR gold film as sensing surface. When the Au NPs-antiadenosine aptamer conjugates solution is added to SPR cell in the absence of adenosine, Au NPs-antiadenosine aptamer conjugates is adsorbed to SPR sensor by the DNA hybridization reaction, and results in a large change of SPR signal. However, the change of SPR signal is decreased when the mixing solution of adenosine with Au NPs-antiadenosine aptamer conjugates is added. This is because adenosine reacts with antiadenosine aptamer in Au NPs-antiadenosine aptamer conjugates and changes its structure from ss-DNA to tertiary structure, which cannot hybridize with its partial complementary ss-DNA immobilized on SPR gold surface. Based on this principle, a SPR sensor for indirect detection of adenosine can be developed. The experimental results confirm that the SPR sensor possesses a good sensitivity and a high selectivity for adenosine, which indirectly confirms that Au NPs-aptamer conjugates is a powerful competitive reagent. More significantly, it can be used to develop other SPR sensors based on ICIA to detect different targets by changing the corresponding type of aptamer in Au NPs-aptamer conjugates.     

Electrochemical enzyme immunoassay using immobilized antibody on gold film with monitoring of surface plasmon resonance signal

Sandwich immunoassay was conducted on a thin gold film set in a surface plasmon resonance (SPR) cell. Monochronal antibody (anti-IgG) was immobilized onto the gold film via 4,4′-dithiodibutyric acid (DDA) and avidin-biotin bonding. Next, IgG sample and alkaline phosphatase-conjugated anti-IgG (ALP anti-IgG) were introduced into the cell successively. Finally, p-aminophenyl phosphate (PAPP) was injected as an enzyme substrate, and the produced p-aminophenol (PAP) was electrochemically measured. Flow did not need to be stopped for incubation for the enzyme reaction, because of the thinness of the cell. In these processes, all the antigen-antibody reactions took place on the gold film. Therefore, the immobilization was performed quickly, and each process could be confirmed by SPR signal. This system had the advantage that the middle of the complicated process could be monitored. For example, the amount of antibody immobilized, which affected on the final electrochemical signal, could be confirmed in the course of immobilization. It was also convenient to investigate process conditions, such as removal of used antigens and labeled antibodies. Good correlation was obtained between the electrochemical current and the SPR signals due to the adsorption of IgG and ALP anti-IgG, and the sensitivity of the electrochemical measurement was much higher than the SPR’s.     

Surface characterization and efficiency of a matrix-free and flat carboxylated gold sensor chip for surface plasmon resonance (SPR)

We report the preparation and characterization of a matrix-free carboxylated surface plasmon resonance (SPR) sensor chip with high sensing efficiency by functionalizing a bare gold thin film with a self-assembled monolayer of 16-mercaptohexadecanoic acid (SAM–MHDA chip). The self assembled monolayer surface coverage of the gold layer was carefully evaluated and the SAM was characterized by infrared reflection absorption spectroscopy, X-ray photoemission spectroscopy, atomic force microscopy, X-ray reflectivity-diffraction, and SPR experiments with bovine serum albumin. We compared the SPR signal obtained on this chip made of a dense monolayer of carboxylic acid groups with commercially available carboxylated sensor chips built on the same gold substrate, a matrix-free C1 chip, and a CM5 chip with a ~100 nm dextran hydrogel matrix (GE Healthcare). Two well-studied interaction types were tested, the binding of a biotinylated antibody (immunoglobulin G) to streptavidin and an antigen–antibody interaction. For both interactions, the well characterized densely functionalized SAM–MHDA chip gave a high signal-to-noise ratio and showed a gain in the availability of immobilized ligands for their partners injected in buffer flow. It thus compared favourably with commercially available sensor chips.     

波长检测型表面等离子体共振传感器对硫堇电聚合成膜的原位分析

利用波长检测型表面等离子体共振(SPR)传感器对硫堇在金膜表面的电化学聚合成膜过程进行了跟踪分析.结果表明,在固定入射角下SPR共振波长随循环伏安扫描周数的增加而线性红移,表明聚硫堇膜的生长是匀速的;扫描100周后共振波长红移总量为96.6 nm.对该实验结果进行理论拟合,得出聚硫堇膜的厚度约为71 nm.聚硫堇膜在酸性缓冲液中的电化学活性很高,其电化学反应过程受扩散控制,在一个完整的循环伏安扫描过程中SPR共振波长的变化完全可逆,说明聚硫堇膜的氧化反应和还原反应是一对可逆过程.与还原态聚硫堇膜相比,氧化态聚硫堇膜对应的SPR共振波长较大,说明氧化态聚硫堇膜折射率高.     

QCM and EC-SPR Studies of Cytochrome cSelf-assembled on Au Electrode and Enhancement of SPR Signal by Au Nanoparticles

Quartz crystal microbalance(QCM) and cyclic voltammetry(CV) were used to characterize the monolayer of cytochrome c(Cyt c), which was adsorbed on gold film modified with alkanethiol mixed monolayer. A direct comparison of protein surface coverages calculated from QCM and cyclic voltammetric measurements illustrates that the ratio of the electroactive Cyt c to the total surface-confined Cyt cis 34%, which suggests that the orientation is a main factor affecting the electroactivity of Cyt c. Moreover, surface plasmon resonance(SPR) measurement combined with CV “in situ” was used to investigate the conformational change of Cyt c in the redox process. Besides, Au nanoparticles(Au NPs) were adsorbed on the surface of Cyt c. The result indicates that Au NPs promote electron transfer between Cyt c and the gold electrode, and SPR result suggests Au NPs enhance SPR signal.     

Surface plasmon resonance and electrochemistry characterization of layer-by-layer self-assembled DNA and Zr4+ thin films, and their interaction with cytochrome c

Through electrostatic layer-by-layer (LbL) assembly, negatively charged calf thymus double stranded DNA (CTds-DNA), and positively charged Zr⁴⁺ ions were alternately deposited on gold substrate modified with chemisorbed cysteamine. Thus-prepared three-dimensional DNA networks were characterized by surface plasmon resonance (SPR) spectroscopy, X-ray photoelectron spectroscopy (XPS) and infrared reflection-absorption spectroscopy (IR-RAS). SPR spectroscopy indicates that the effective thickness of DNA monolayer in the (DNA/Zr⁴⁺)₁ bilayer was 1.5 ± 0.1 nm, which corresponds to the surface coverage of 79% of its full packed monolayer. At the same time, a linear increase of film thickness with increasing number of layers was also confirmed by SPR characterizations. The data of XPS and IR-RAS show that Zr⁴⁺ ions interact with both the phosphate groups and nitrogenous bases of DNA and load into the framework of DNA. Furthermore, the interactions between this composite film and heme protein cytochrome c (Cyt c) were investigated by SPR spectroscopy and electrochemistry. Compared with the adsorption of Cyt c on DNA monolayer, this composite multilayer film can obviously enhance the amount of immobilized Cyt c confirmed by SPR reflectivity-incident angle (R-θ) curves. Cyclic voltammetry (CV) indicates the Cyt c adsorbed on the composite film is electroactive, and the enhancement of peak current in CV indirectly verifies the increase of the amount of immobilized Cyt c.     

基于金银合金薄膜的高灵敏度宽光谱表面等离子体共振成像传感器

报道了一种基于金银合金薄膜的宽光谱表面等离子体共振成像(SPRI)传感器,该传感器能够对吸附在薄膜局部或整个表面上的生化分子进行原位定量检测,而且与常规的金膜SPRI传感器相比,检测成本更低,检测灵敏度更高。利用质量比1:1的金银合金溅射靶在玻璃基板上淀积了厚约50 nm的均匀的金银合金薄膜。利用实验室自制的Krestchmann结构多功能平台在不同入射角下测试了金银合金薄膜被纯水覆盖后的SPR光谱和SPR彩色图像。基于色相算法计算获得了每个SPR彩像的二维色相分布及其平均色相,从而使得宽光谱SPRI传感器能够利用平均色相作为灵敏度参数进行定量检测。实验确定了平均色相对溶液折射率(RI)变化和分子吸附最为敏感的光谱区间是595–610 nm之间。在这个窄光谱范围内,平均色相与共振波长呈线性关系,其斜率为?hue/?λR=7.52 nm~(-1),这意味着基于色相的RI灵敏度是基于共振波长的RI灵敏度的7.52倍,这一结论已被实验证明。将SPRI传感器的起始共振波长设定在色相敏感光谱区间内之后,实验测得基于色相的RI灵敏度为S=29879 RIU~(-1),比在相同条件下测得的金膜SPRI的灵敏度高8倍。利用时间分辨宽光谱SPRI方法实时监测了牛血清白蛋白(BSA)分子在金银合金薄膜表面的非特异性吸附,从实验测得的平均色相随时间的变化曲线可知BSA吸附达到平衡所需时间约15 min。研究结果表明,基于金银合金薄膜的SPRI传感器具有动态定量检测蛋白质分子吸附过程的功能。