Terrain radiation: Measurement investigation at 94 GHz

Using the 94 GHz — radiometers situated on board of a helicopter and on a measuring tower, there were investigated radiating properties of various surface types of soil and sea under their different states and season-weather conditions. The measurements were accompanied with controlling biogeophysical parameters of the surfaces and atmosphere. The plotted dependencies and the interrelations noticed in the process of discussion of the results of our work may be used when working out and estimating efficiency of the operation algorithms of the systems providing remote sensing of the surround medium.     

206 GHz光子带隙谐振腔回旋管

分析了光子晶体谐振腔的模式选择功能,实现光子晶体谐振腔回旋管振荡器高阶电磁模与高次电子回旋模的有效耦合,并成功抑制了模式竞争。通过对光子晶体谐振腔禁带特性的分析,定出了工作模式为TE23模,还建立了光子晶体谐振腔回旋管的等效半径的概念,设计了自洽非线性理论和相关的计算机数值模拟程序。研究发现TE23模能有效地与电子的二次回旋谐波相互作用,其耦合频率为206 GHz,并极大地降低了对工作磁场的要求。在考虑诸多物理因素影响的情况下,对该二次谐波光子带隙谐振腔(PBGC)回旋管振荡器进行了参数优化,得到了电压40 kV、电流4.2 A、磁场3.925 T、输出功率35 kW、互作用效率21%的二次谐波TE23模PBGC回旋管振荡器。     

110 GHz太赫兹波大气击穿阈值及最大传输能量密度

随着110 GHz高功率太赫兹波功率容量的提升,其引起的大气击穿问题越来越受到重视。将若干等效电离参数表达式引入到电子雪崩密度方程中,计算了不同压强下的大气击穿阈值。结果表明,由Ali等效电离参数得到的110 GHz击穿阈值与实验数据符合得很好。在此基础上,利用Ali等效电离参数对逃逸传输能量密度与太赫兹波振幅的关系进行了分析。结果表明,当太赫兹波振幅小于击穿阈值时,逃逸传输能量密度随功率密度的增加线性增加;当太赫兹波振幅大于击穿阈值时,逃逸传输能量密度随功率密度先减小后增大。     

Stroboscopic X-ray imaging of vibrating dislocations excited by 0.58 GHz phonons

We report on direct imaging, by means of stroboscopic x-ray topography, of phonon-induced dislocation vibrations. X-ray images taken from LiNbO3 crystals excited by 0.58 GHz surface acoustic waves, showed individual acoustic wave fronts as well as their distortions when crossing the dislocation line. The observed contrast is well explained by considering the dynamic deformation field of vibrating dislocation. Comparing simulated deformation maps and x-ray images permitted determination of the local velocities of vibrating dislocations and their viscosity coefficients. We found unexpectedly high velocity values (not far from the speed of sound) and extremely low viscosity coefficients, 2-3 orders of magnitude lower than previously measured in ductile materials.     

9.33 GHz高功率脉冲微波对IAR20鼠肝细胞和L-02人肝细胞增殖的影响

研究了9.33 GHz高功率脉冲微波对IAR20鼠肝细胞和L-02人肝细胞增殖的影响,利用噻唑蓝比色法测量细胞增殖并对实验数据进行拟合,得到脉冲个数、场强和脉宽与细胞增殖之间的关系。当脉冲微波场强与脉宽保持不变,脉冲微波细胞效应随脉冲个数呈现非线性的指数递增规律。当脉冲微波的脉冲个数、脉宽一定时,场强越大,细胞增殖被抑制的程度越大;当脉冲个数、场强不变,脉宽越大,细胞增殖受到抑制的作用越明显,即脉冲微波细胞效应与场强和脉宽成正比。相同脉冲微波参量对不同种类细胞增殖的影响是不同的,对IAR20鼠肝细胞的影响比对L-02人肝细胞的影响略大。     

全三维110GHz和220GHz同轴腔双注回旋管数值模拟研究

为了打破传统单注回旋管只能产生较低功率的局限性, 本文基于自主研发的PIC粒子模拟软件CHIPIC 对110 GHz和220 GHz同轴腔双注回旋管进行全三维数值模拟研究. 在理论分析同轴双电子注电子枪设计模型和初始参数的基础上通过CHIPIC对其进行优化设计, 得到了具有横纵速度比为1.0, 最大速度零散约为5.4%的高性能电子束; 并将此优化后的双阳极双注电子枪取代传统回旋管数值模拟时采用的回旋 发射进行110 GHz和220 GHz双注回旋管整管的数值模拟, 并采用MPI四进程并行计算, 最终获得了具有双频分别为110 GHz和220 GHz、模式为TE₀₂模、平均输出功率约在70 kW、 效率达到8.75%的高性能双注回旋振荡管. 关键词： 同轴腔双注回旋管 同轴双电子注电子枪 横纵速度比 速度零散     

Two-dimensional pulsed TRIPLE at 95 GHz

The one-dimensional (1D) pulsed TRIPLE resonance experiment, introduced by Mehring et al. (M. Mehring, P. Hofer, and A. Grupp, Ber. Bunseges. Phys. Chem. 91, 1132-1137 (1987)) is a modification of the standard Davies ENDOR experiment where an additional RF pi-pulse is applied during the mixing time. While the first RF pulse is set to one of the ENDOR transitions, the frequency of the second RF pulse is scanned to generate the TRIPLE spectrum. The difference between this spectrum and the ENDOR spectrum yields the difference TRIPLE spectrum, which exhibits only ENDOR lines that belong to the same M(S) manifold as the one selected by the first RF pulse. We have extended this experiment in two dimensions (2D) by sweeping the frequencies of both RF pulses. This experiment is particularly useful when the spectrum is congested and consists of signals originating from different paramagnetic centers. The connectivities between the peaks in the 2D spectrum enable a straightforward assignment of the signals to their respective centers and M(S) manifolds, thus providing the relative signs of hyperfine couplings. Carrying out the experiment at high fields has the additional advantage that nuclei with different nuclear gyromagnetic ratios are well separated. This is particularly true for protons which appear at significantly higher frequencies than other nuclei. The feasibility and effectiveness of the experiment is demonstrated at W-band (94.9 GHz) on a crystal of Cu(2+)-doped l-histidine. Homonuclear (1)H-(1)H, (14)N/(35)Cl-(14)N/(35)Cl and heteronuclear (1)H-(14)N/(35)Cl 2D TRIPLE spectra were measured and from the various connectivities in the 2D map the (1)H, (14)N, and (35)Cl signals that belong to two different Cu(2+) centers were identified and grouped according to their M(S) manifolds. Copyright 2000 Academic Press.     

Polarization of microwave noise source radiation in the 30 GHz to 300 GHz range

The radiation spectra of three microwave noise sources (C. P. Clare & Co., TN type series) have been compared to determine the frequency bandwidth and their polarization. A Lamellar Grating Fourier Transform spectrometer was used with a Helium cooled bolometer detector in the wavelength region of lmm to 10mm. The spectral regions were compared with the manufacturer's specifications and the results were in partial agreement. A secondary transmission region was observed to have an input current as well as a polarization dependence despite the directional output of the waveguide antenna.     

一种用于60 GHz通信的S型结构左手材料的设计

基于对S型结构的理论分析,将中心频率设置为60 GHz,通过合理的改变单元结构中相应的尺寸以实现所需电谐振和磁谐振频率,并且经过优化以实现负介电常量和负磁导率的重合频段尽可能理想. 运用反演参量提取方法进行电磁参量提取,可以得到本设计在58.1~61.4 GHz频段内其ε和μ同时为负,即左手频段. 分析散射参量的仿真结果,在58~62 GHz频段内S₂₁大于-3 dB,在59.8~60.4 GHz频段内,S₁₁小于-20 dB,因此该设计结果可以运用于60 GHz通信滤波器和天线等器件的研究与设计.     

一种220 GHz分布作用速调管的高频系统模拟

对一种基于双排矩形波导慢波结构(SDRWS) 结构的3腔EIK进行了详细计算机模拟计算, 通过对基于SDRWS结构的EIK用输入输出腔的S11的模拟计算及对分布作用速调管用中间腔的本征频率的模拟计算, 初步确定了EIK用输入输出腔及中间腔的结构参数, 进而对EIK进行了PIC互作用模拟计算, 结果表明: 该EIK的3dB工作频带为219.5~220.5GHz, 3dB带宽为1GHz, 最大功率为456 W, 最大增益为40.06dB。在此基础上, 通过调整中间腔的波导头宽度以进行参差调谐, 用PIC互作用模型模拟计算研究了中间腔谐振频率对EIK整体性能的影响。结果表明, EIK的3dB工作频带主要由输入输出腔的通频带决定, 而中间腔的谐振频率也具有重要影响。当中间腔的谐振频率分别处于输入输出腔的通频带的低频端或高频端时, 可以使EIK的3dB工作频带向低频端或高频端得到一定程度展宽; 当中间腔的谐振频率高于输入输出腔的通频带的高频端时, EIK的增益在其3dB工作频带内较为平坦, EIK的输出信号在其3dB工作频带内比较稳定, 频谱的纯净程度较好。参差调谐的最终结果表明, 当中间腔的波导头宽度为0.747mm时, EIK获得了接近最优的性能, 3dB工作频带为219.5~220.0GHz, 3dB带宽扩展到1.2GHz, 最大功率为630W, 相应的最大电子效率为11.3%, 最大增益为47dB。     

Pressure Broadening of the Rotational Line of Oxygen at 425 GHz

The pressure broadening of the ¹⁶O¹⁶O rotational line (N, J)=(3, 2)-(1, 2) at 425 GHz by oxygen and nitrogen perturbers at room temperatures have been reported. A spectrometer with BWO and acoustic detector was employed with a double magnetically shielded cell. The signal-to-noise ratio on the line was about 200-250 for self-broadening and about 100 for broadening by N₂ measurements. The pressure-broadening parameters of the line at room temperature (23±0.5°C) were measured as 2.19±0.01 MHz/Torr for self-broadening and 2.215±0.02 MHz/Torr for broadening by nitrogen. Values of these parameters significantly (by about 25%) differ from ones previously measured by H. M. Pickett, E. A. Cohen, and D. E. Brinza, (Astrophys. J.248, L49-L51 (1981)). The results of the present work show the necessity for correction of broadening parameters of this line for the purpose of Earth atmosphere remote sensing. The central frequency of the transition (N, J)=(3, 2)-(1, 2) was measured as 424 763.023±0.020 MHz.     

1.3 GHz 20 kW固态微波功率源的测试和运行（英）

北京大学3.5-cell直流超导(DC-SRF)光阴极注入器需要一台连续波功率20 kW的1.3 GHz微波功率源。为此北京大学和北京北广科技股份有限公司联合研制了一台由88个放大模块组成的固态微波功率放大器,这是国内首台L波段连续波大功率固态功率源。在简要介绍这台微波功率放大器设计的基础上,主要描述其调试过程和重要参数检测并着重讨论了全反射问题。测试结果显示这台功率源的各项参数均达到设计指标,在输出功率20 kW时的效率为34%,增益大于85 dB;在整个功率输出范围其增益和相移的变化分别为1.6 dB和9.5。目前这台功率源已在DC-SRF光阴极注入器调试运行中稳定工作超过2000 h。     

94GHz基波复合腔回旋管数值模拟

通过对94 GHz基波复合腔回旋管中谐振腔结构、电子注参数以及注-波互作用过程的模拟计算研究,分析了复合腔回旋管的高频结构特性和工作参数优化问题.给出了基波H61 -H62模式对复合腔回旋管的模拟设计结果.数值模拟结果表明:在电子注电压40 kV、电流5A、电子横纵速度比1.3、工作磁场3.6T时,回旋管可获得78 k...     

High-frequency 180 GHz PELDOR

For aromatic organic radicals, pulsed electron-electron double resonance (PELDOR) experiments at high magnetic fields offer the possibility to achieve orientation-selective pumping and detection that could allow one not only to determine the distance between paramagnetic species but also their relative orientation with respect to the interconnecting dipolar axis. We present a PELDOR two-frequency setup that was introduced into our homebuilt 180 GHz pulsed electron paramagnetic resonance (EPR) spectrometer and we discuss its technical and experimental features. The capability of 180 GHz PELDOR has been tested using the three-pulse ELDOR sequence on the protein RNR-R2 (ribonucleotide reductase) fromEscherichia coli, which contains two tyrosyl radicals at a distance of 3.3 nm. At 180 GHz, orientation selectivity is observed and the modulation frequency was found in good agreement with theoretical predictions, which take into account the relative orientation of the radicals from X-ray data.     

1.06kW 13GHz线宽全光纤激光器

分析了高功率光纤激光器中受激布里渊散射(SBS)效应的抑制方法。研究表明,利用宽带噪声源高速相位调制展宽光谱的方法对于抑制SBS十分有效,可实现kW级用于光谱组束的数10GHz高功率光纤激光子束。通过理论计算线宽与SBS阈值的关系,并分析噪声相位调制各参数对SBS阈值提升的影响,优化了光纤激光器设计参数。通过宽带噪声高速相位调制的方法,展宽单频种子源线宽至13GHz,通过两级预放大至10 W后,使用20/400μm掺Yb光纤最终实现了中心波长1064nm、线宽13GHz、最高功率1.06kW的激光输出,光束质量M21.2,光-光转换效率86%,实验过程未观测到模式不稳定性现象。进一步扩宽噪声源频带,加大调制深度,有望实现更高功率的窄线宽光纤激光输出。     

94 GHz单阳极磁控注入式电子枪初始参数设计

根据94 GHz回旋振荡管对电子束的需求,在理论分析电子枪工作原理的基础上通过大量编程对94 GHz单阳极磁控注入式电子枪的一系列参数进行了初始设计, 基于粒子模拟软件CHIPIC开发了专门针对磁控注入式电子枪的计算模块并对其进行了数值模拟。模拟结果显示:该枪的电子束横纵速度比为1.42、速度零散为4.6%,符合回旋振荡管对电子注的要求。     

Numerical design of 120 GHz, 1 MW gyrotron interaction cavity

The design and the numerical simulation of the interaction cavity for 120 GHz, 1 MW gyrotron is presented. The optimizations of the cavity parameters are carried out by using the Particle-in-Cell, 3D-electromagnetic simulation code MAGIC. The co-rotating TE_22,6 mode is selected by using the in-house developed code GCOMS. The cold cavity and the beam–wave interaction analyses are carried out to analyze the eigenmode, eigenfrequency and the output power performance. The output power more than 1 MW is achieved at the magnetic field of 4.82 T. The sensitivity analyses of the output power and the frequency with respect to the various interaction cavity parameters are also performed.     

Hypersound attenuation and phase velocities in evaporated polycrystalline films of silver,copper and constantan between 1 and 24 GHz

A model for a recombination instability in a semiconductor far from equilibrium is analysed. It is based upon the simultaneous impact ionization of ground state and excited donors at low temperature. The number and the stability of spatially homogeneous steady states and their dependence upon external control parameters is investigated. For certain values of these parameters bistability andS-shaped current-voltage characteristics are found. Nonequilibrium phase transitions of first order between low and high conductivity states can be induced by varying the applied voltage. If certain generation coefficients are negligible, the transition changes from first to second order above some tricritical value of the other parameters.     

5.8GHz磁控管的数值模拟和实验研究

C波段高稳定度磁控管是目前磁控管的研究重点。对5.8GHz磁控管进行模拟研究,冷腔计算磁控管π模频率为5.863GHz,阳极用双端双隔模带结构磁控管的工作频率与相邻模式频率分隔度为44%。模拟磁控管输出频率为5.856GHz,输出微波功率约1.2kW。对研制的磁控管进行注入锁定实验研究,输出微波功率1.047kW,效率约为58%。磁控管锁频锁相后输出的频率和相位稳定。     

Ultra‐light carbon nanotube sponge as an efficient electromagnetic shielding material in the GHz range

CVD synthesised CNT flexible sponge with density lower than 0.02 g cm^–3 has been found to serve as high performance EMI shielding material without the aid of any polymer infiltration or impregnation. Due to its extreme lightweight, the specific SE of the CNT‐sponge was found to be as high as 1100 dB cm³ g^–1, having a total SE above 20 dB in the whole 1–18 GHz range, and being able to shield by absorption. The material is the best of our knowledge this specific SE value appears to be the highest reported hitherto. Improved EM absorbers should fulfil the synergic requirements of being low reflective and highly absorptive. In our CNT‐sponges this condition is not satisfied because, although their net absorption ability is strongly remarkable, their high electrical conductivity favours the wave to be reflected at the input interface. Therefore, this sponge material would have a great potential for microwave‐frequency applications that need negligible reflection and great absorption when combined in a multilayered structure that could prevent the wave to be reflected at the input interface. (© 2014 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)