A novel amphipathic block copolymer coating forming micelle-like aggregates for separation of steroids in open tubular capillary electrochromatography

A new amphipathic block copolymer, poly(tert-butyl acrylate)₁₂₇-block-poly(glycidyl methacrylate)₈₆, was developed for the coating in open tubular capillary electrochromatography. The self-assembly characters of the coating, which could form micelle-like aggregates under proper conditions, were observed by atomic force microscopy. Compared with bare capillary, this coating could act as surfactant and lead to improve the separation of steroids. In addition, the influence of pH, buffer concentration and organic solvents on the separation was investigated. The best separation of the three model steroid analytes could be achieved using 20.0 mM borate buffer at pH 10.5. For covalent bonding, the coating showed good repeatability and stability with RSD of u_EOF less than 3.3%. Then, this proposed method was well validated with good linearity (≥0.999), recovery (91.0-94.0%) and repeatability, and was successfully used for separation of steroids in spiked serum samples, which indicated that this new OT-CEC method could provide a potential tool to determine steroids in real biological system without interference.     

Highly fluorinated polymers with sulfonate,sulfamide and N,N‐diethylamino groups for the capillary electromigration separation of proteins and steroid hormones

Highly fluorinated polymers are promising materials in separation methods due to their combination of high chemical and thermally stability, hydro‐ and oleophobicity, and weak intermolecular forces. However, application of these polymers in chromatography is limited because of their low solubility in aqueous‐organic solvents. In our research, the highly fluorinated water soluble polymers with –SO₃⁻N(Et)₄⁺, –SO₂NH₂, and –N(Et)₂ terminal groups were synthesized and applied as additives to the background electrolyte for the separation of steroid hormones and proteins by capillary electromigration methods. It is shown that highly fluorinated polymers can be used both as pseudo‐stationary phases in electrokinetic chromatography for high separation efficiency (N  ∼ 200 × 10³) and selectivity (α  ∼  1.1) of uncharged analytes (e.g., steroid hormones), and as dynamic modifiers of fused silica capillary walls. The highest separation efficiency (N  ∼ 1 × 10⁶) and selectivity (α  ∼ 1.3) of steroid hormones was achieved by combination of sodium dodecyl sulfate and fluoropolymer with sulfonate groups in background electrolyte with pH 2. Dynamic wall coatings based on fluoropolymer with –SO₂NH₂ (which are easier and faster to create and wash off) exhibit significantly higher separation efficiency and selectivity compared to capillary electrochromatography on capillary columns based on polymethacrylate polymers.     

磷脂的分离纯化及高效毛细管电泳分析

采用溶剂提取和柱色谱法分离纯化市售大豆粉末磷脂(卵磷脂含量14.05%),得到高纯度的卵磷脂产品(纯度92.80%)。重点建立了磷脂的胶束电动毛细管色谱(MECC)分离分析方法。以分离度和峰面积为优化指标,对表面活性剂及其浓度、电泳缓冲液pH、有机改性剂及其含量、缓冲液浓度、温度等条件进行优化,确定了最优化电泳条件:电泳缓冲液为35 mmol/L脱氧胆酸钠-1 mmol/L 硼砂缓冲液/正丙醇(体积比为57∶43)(pH 8.30),柱温44 ℃,操作电压25 kV,检测波长200 nm;内加法定性磷脂组分;外标法定量卵磷脂。结果表明,MECC法能有效分离5种磷脂组分;0.1～1 g/L的质量浓度范围内卵磷脂的线性关系良好(r=0.9990),平均回收率为98.0%,日内、日间精密度分别为1.36%和3.27%,定性结果与薄层色谱法、红外光谱法的定性结果相符。     

咖啡因及其9种类似物的胶束电动毛细管分析研究

 以十二烷基硫酸钠 (SDS)胶束为准固定相 ,考察了咖啡因及其 9种类似物在胶束电动毛细管 (MECC)分离模式下的分离行为。研究了运行缓冲液的 pH值、磷酸盐浓度、SDS浓度、甲醇体积分数、分离电压、分离温度等因素对这 10种化合物的迁移时间和分离效果的影响。结果发现 ,这些因素对上述 10种化合物的分离有显著的影响 ,尤以pH值为最。它不仅影响化合物的迁移时间和分离效率 ,还改变其出峰顺序 ,这与碱性条件下化合物仲胺基上氢的电离有关。优化后的分离条件 :运行缓冲液为 2 0mmol/L磷酸盐 2 0mmol/LSDS(pH 11 0 ) ,分离电压为2 5kV。     

咔唑-9-乙基氯甲酸酯柱前衍生氨基酸胶束电动色谱分离

采用一种新型紫外、荧光衍生试剂咔唑-9-乙基氯甲酸酯对9种氨基酸(丝氨酸、苏氨酸、甘氨酸、谷氨酸、天冬氨酸、缬氨酸、异亮氨酸、亮氨酸、苯丙氨酸)进行柱前衍生,采用胶束电动色谱模式在14 min内完成分离。分离条件：以pH 9.0的 20 mmol/L硼酸盐-30 mmol/L十二烷基硫酸钠(SDS)溶液（含3%(体积分数)乙腈)为缓冲溶液,柱温25 ℃,分离电压18 kV,紫外检测波长214 nm。该方法的线性范围为0.025~0.25 mmol/L,检出限为2.15~2.46 μmol/L。     

Evaluation of poly([2‐(acryloyloxy)ethyl]trimethylammonium chloride) cationic polymer capillary coating for capillary electrophoresis and electrokinetic chromatography separations

Capillary electrophoresis and electrokinetic chromatography are typically carried out in unmodified fused‐silica capillaries under conditions that result in a strong negative zeta potential at the capillary wall and a robust cathodic electroosmotic flow. Modification of the capillary wall to reverse the zeta potential and mask silanol sites can improve separation performance by reducing or eliminating analyte adsorption, and is essential when conducting electrokinetic chromatography separations with cationic latex nanoparticle pseudo‐stationary phases. Semipermanent modification of the capillary walls by coating with cationic polymers has proven to be facile and effective. In this study, poly([2‐(acryloyloxy)ethyl]trimethylammonium chloride) polymers were synthesized by reversible addition‐fragmentation chain transfer polymerization and used as physically adsorbed semipermanent coatings for capillary electrophoresis and electrokinetic chromatography separations. An initial synthesis of poly([2‐(acryloyloxy)ethyl]trimethylammonium chloride) polymer coating produced strong and stable anodic electroosmotic flow of –5.7 to –5.4 × 10⁻⁴ cm²/V⋅s over the pH range of 4–7. Significant differences in the magnitude of the electroosmotic flow and effectiveness were observed between synthetic batches, however. For electrokinetic chromatography separations, the best performing batches of poly([2‐(acryloyloxy)ethyl]trimethylammonium chloride) polymer performed as well as the commercially available cationic polymer polyethyleneimine, whereas polydiallylammonium chloride and hexadimethrine bromide did not perform well.     

Simultaneous Separation and Determination of Benzoic Acid Compounds in the Plant Medicine by High Performance Capillary Electrophoresis

A simple and inexpensive high performance capillary electrophoresis (HPCE) was applied to separate five benzoic acid compounds simultaneously. The investigation was carried out by micellar electrokinetic capillary chromatography (MECC). To avoid a time‐consuming and tedious procedure, orthogonal experimental design OA₉ (3⁴) for separation experiments was applied to find the optimal conditions in terms of the resolution and analytical time. The best conditions for separation were obtained using a 20 mM borax and 30 mM sodium dodecyl sulfate (SDS) buffer (pH 9.8) containing 2 mM β‐CD and 4% methanol (v/v). Online UV detection was performed at 250 nm. A voltage of 16 kV was applied and the temperature was controlled at 25 °C. Injection was performed for 5 s. The method was validated for the quantification of benzoic acid, salicylic acid and ortho‐aminobenzoic acid in Radix Isatidis, a traditional plant medicine with removal of endotoxin. The separation and determination were satisfactory and quick.     

Analysis of Calix[4]arenes Using Nonaqueous Capillary Electrophoresis

In nonaqueous capillary electrophoresis (NACE), an organic solvent is used in place of an aqueous medium as the background solution to improve the solubility and selectivity for hydrophobic analytes. In this study, we employed NACE with UV detection for the analysis of eight calix[4]arenes. We examined the influence of several parameters—the buffer composition, the nonaqueous solvent‘s composition and proportion, and the concentration of the electrolyte of the nonaqueous buffer—on the efficiency of the electrophoretic separation. The separation was achieved through the analyte's different effective mobility via different degrees of deprotonation on the phenolic OH groups of the calix[4]arene. This deprotonation can further affect the analyte's ability to form a complex with the metal ion. The optimized background electrolyte (BGE), comprising a mixture of N‐methylformamide/acetonitrile (30:70, v/v) and 100 mM AcOH/20 mM NH₄OAc, provided rapid (<11 min) separation of the calix[4]arenes with good resolution. The relative standard deviations of the migration times for the eight analytes were all less than 1%. Within the calibration concentration range, the coefficients of determination (R²) were all greater than 0.9914. Thus, the present study demonstrated NACE can provide adequate separation for the analysis of calix[4]arenes.     

非水胶束电动色谱分离邻苯二甲酸酯类化合物

非水胶束电动色谱(NAMEKC)兼具非水毛细管电泳的优点和胶束电动色谱的分离机制,尤其适于对强疏水性化合物进行分离分析。在以甲酰胺为非水溶剂的电泳介质中,采用十二烷基硫酸钠（SDS）形成胶束相,开展NAMEKC方法的研究。通过添加水溶液、调节水溶液酸度、添加有机溶剂、改变SDS浓度等操作条件的考察,在15 min 内实现了3种美国环保局优先监测的污染物——邻苯二甲酸二甲酯、邻苯二甲酸二乙酯、邻苯二甲酸二丁酯的分离。分离度最小者为1.5,检测限优于3.04 mmol/L(以信噪比为3计)。3种典型的强疏水性物质的成功分离,显示出NAMEKC方法在分离疏水性物质方面的优势,扩展了NAMEKC在电中性有机物分析中的应用。     

Anionic liposomes in capillary electrophoresis: Effect of calcium on 1-palmitoyl-2-oleyl-<Emphasis Type="Italic">sn</Emphasis>-glycero-3-phosphatidylcholine / phosphatidylserine-coating in silica capillaries

The effect of calcium on phospholipid coatings in fused silica capillaries used in capillary electrophoresis was studied. The anionic liposomes used for the coating consisted of 3 mM 1-palmitoyl-2-oleyl-sn-glycero-3-phosphatidylcholine and phosphatidylserine in the ratio 80/20 mol%. Coating was performed as part of the preconditioning, and the capillaries could be used for several runs without the need for liposomes in the background electrolyte solution or for liposome rinses between runs. Phospholipids could easily be flushed away by rinsing with a chloroform-methanol (2:1 v/v) mixture, which made it possible to recoat and reuse the capillaries. A calcium:phospholipid ratio of approximately 3 gave the most stable coating. The stability of the coating and success of the coating procedure were studied by measuring the electroosmotic flow and by separating uncharged steroids, which were used as model compounds. Many parameters that affect the coating, such as preconditioning (with different acids and bases), buffer, temperature during coating, and the physical structures of liposomes, were studied, with and without calcium in the liposome solution. The separation of steroids was improved and was less dependent on coating conditions when calcium was present during the coating. Capillaries optimally coated with anionic phospholipids were applied in the separation of phenols.     

聚合物涂层在毛细管电泳分离蛋白中的研究进展

毛细管电泳具有分析时间短,分离效率高,样品消耗量少等优点,在生物样品分离,特别是蛋白质分析领域有重要应用。然而,毛细管内壁硅羟基的解离给分离结果带来诸多不良影响。聚合物涂层能够抑制蛋白质在毛细管内壁的吸附以及调控电渗流,故对毛细管内壁进行有效修饰能够提高其对蛋白质的分离效率及分离稳定性。该文主要综述了动态及静态聚合物涂层毛细管的最新研究进展,并概述了近些年基于多巴胺/聚多巴胺发展起来的涂层毛细管的研究进展,最后展望了聚合物涂层毛细管的发展趋势。     

Rapid and cost‐effective method for the simultaneous quantification of seven alkaloids in Corydalis decumbens by microwave‐assisted extraction and capillary electrophoresis

A rapid and cost‐effective method based on microwave‐assisted extraction followed by capillary electrophoresis was developed for simultaneous quantification of seven alkaloids in Corydalis decumbens for the first time. The main parameters affecting microwave‐assisted extraction and capillary electrophoresis separation were investigated and optimized. The optimal microwave‐assisted extraction was performed at 40°C for 5 min using methanol/water (90:10, v/v) as the extracting solvent. Electrophoretic separation was achieved within 15 min using an uncoated fused‐silica capillary (50 μm internal diameter and 27.7 cm effective length) and a 500 mM Tris buffer containing 45% v/v methanol (titrated to pH^* 2.86 with H₃PO₄). The developed method was successfully applied to the quantification of seven alkaloids in Corydalis decumbens obtained from different regions of China. The combination of microwave‐assisted extraction with capillary electrophoresis was an effective method for the rapid analysis of the alkaloids in Corydalis decumbens .     

Enhanced capillary zone electrophoresis in cyclic olefin copolymer microchannels using the combination of dynamic and static coatings for rapid analysis of carnosine and niacinamide in cosmetics

Cosmetics that have medicinal effects, including anti-inflammatory and antioxidant, have become a daily care routine consumption. The peptide additives, such as carnosine and nicotinamide, were frequently used to realize these medicinal effects. To accomplish rapid and effective quantitation of carnosine and niacinamide in cosmetics, capillary zone electrophoresis was executed in cyclic olefin copolymer microchips having both dynamic and static coatings. The static coating of cyclic olefin copolymer microchannel was constructed from bovine serum albumin adsorption, immobilization, and active site closure, while the dynamic coating was formed by adding surfactant into running buffer of capillary zone electrophoresis. The static coating can improve the hydrophilicity of cyclic olefin copolymer surface and avoid nonspecific peptide adsorption. The dynamic coating of sodium dodecyl sulfate in running buffer proved to be useful in flow velocity adjustment and the column efficiency enhancement in the capillary zone electrophoresis separation channel of the cyclic olefin copolymer microchip device. A separation resolution up to 4.24 on the mixture of carnosine and nicotinamide was obtained. Moreover, an analysis method was established and applied to simultaneous carnosine and nicotinamide determination in a liquid whitening essence and a solid antiglycation pill, and the results were verified by comparison with high-performance liquid chromatography methods, indicating its potential in complex sample analysis.     

Genotyping of α-thalassemia deletions using multiplex polymerase chain reactions and gold nanoparticle-filled capillary electrophoresis

A gold nanoparticle-filled capillary electrophoresis method combined with three multiplex polymerase chain reactions (PCRs) was established for simultaneous diagnosis of five common α-thalassemia deletions, including the -α^3.7 deletion, -α^4.2 deletion, Southeast Asian (- -^SEA), Filipino (- -^FIL) and Thai (- -^THAI) deletions. Gold nanoparticles (GNPs) were used as a pseudostationary phase to improve the resolution between DNA fragments in a low-viscosity polymer. To achieve the best CE separation, several parameters were evaluated for optimizing the separation conditions, including the capillary coating, the concentrations of polymer sieving matrix, the sizes and concentrations of GNPs, the buffer concentrations, and the pH. The final CE method for separating a 200-base pair (bp) DNA ladder and α-thalassemia deletions used a DB-17 capillary, 0.6% poly(ethylene oxide) (PEO) prepared in a mixture of GNP_32nm solution and glycine buffer (25 mM, pH 9.0) (80:20, v/v) as the sieving matrix with 1 μM YO-PRO-1 for fluorescence detection; the applied voltage was −10 kV (detector at anode side) and the separation temperature was 25 °C. Under these optimal conditions, 15 DNA fragments with sizes ranging from 0.2 kb to 3.0 kb were resolved within 11.5 min. The RSDs of migration times were less than 2.81%. A total of 21 patients with α-thalassemia deletions were analyzed using this method, and all results showed good agreement with those obtained by gel electrophoresis.     

胶束电动毛细管色谱法检测红曲米中的莫纳可林K

建立了测定红曲米中莫纳可林K含量的胶束电动毛细管色谱(MEKC)方法。考察了运行缓冲液的种类、pH及其浓度、有机添加剂、十二烷基硫酸钠(SDS)的浓度和分离电压等实验条件对电泳分离效果及检测灵敏度的影响。在优化的实验条件下,以20 mmol/L硼砂(pH 10.6,含10%(体积分数)乙醇和40 mmol/L SDS)作为缓冲溶液,莫纳可林K能在23 min内实现很好的基线分离,线性范围为5.00～100.00 mg/L,线性相关系数为0.9976,检出限(以信噪比(S/N)为3计)为0.13 mg/L,加标回收率为98.5%～99.5%。精密度和稳定性试验中,峰面积和迁移时间的相对标准偏差均小于3%,表明重复性良好。该方法简便、快速、灵敏,可用于红曲米中莫纳可林K含量的测定。     

Effect of coating electrolytes on two-tailed surfactant bilayer coatings in capillary electrophoresis

Surfactants such as dioctadecyldimethylammonium bromide (DODAB) form semi-permanent coatings that effectively prevent adsorption of cationic proteins onto the fused silica capillary in capillary electrophoresis (CE). The bilayer coating is generated by flushing the capillary with a 0.1 mM surfactant solution. However, formation of the bilayer is strongly dependent on the coating electrolyte. The effect of counter-ions, electrolyte concentrations and buffer co-ions were monitored based on: the separation of basic model proteins; the adsorption kinetics of DODA⁺ onto fused silica; and dynamic light scattering (DLS) to determine vesicle size. Low concentrations (≤10.0 mM) and/or weakly associating buffers such as phosphate (pH 3.0), acetate (pH 4.0) and chloride should be used for DODAB coating solutions. Dissolving the surfactant in strongly associating electrolyte, such as phosphate at pH 7.0, results in poor coating of the capillary surface. Effective cationic bilayer coatings are formed if the buffer conditions favor formation of vesicles with diameters < 300 nm. Monitoring turbidity at 400 nm provides a convenient means of verifying vesicle diameter variation of <5 nm; that is, that the coating solution is effective.     

聚多巴胺表面修饰毛细管电色谱的研究进展

毛细管电泳（CE）具有分离时间短、分离效率高、样品消耗量低等优点,在分离分析领域有着重要应用。原始的未修饰熔融石英毛细管只能提供阴极流向的电渗流和单一的电泳分离机制,分离性能有限,重复性较差,不能满足各类复杂样品体系尤其是中性和手性样品的分离需求。因此,有必要在CE中引入各类毛细管修饰策略,以拓展其实际应用潜力。贻贝仿生聚多巴胺（PDA）及其衍生材料因其简便易行的制备过程、优异的表面黏附性、良好的生物相容性、较强的二次反应活性和化学稳定性等优点,在催化、传感、水处理、样品前处理、生物医药以及CE分离等领域得到了广泛应用。PDA涂层的制备过程与物理吸附涂层一样简便,而表面黏附涂层的稳定性又可与共价键合涂层相媲美,因此非常适用于石英毛细管柱的修饰。更重要的是,PDA涂层较强的二次反应活性使其可作为反应平台进行灵活多样的二次表面修饰,便于构建多功能PDA涂层毛细管电色谱（CEC）固定相。基于这些突出优点,PDA涂层材料在CEC中的巨大应用价值逐渐得到了研究者们的广泛关注。该文首先对近3年有关PDA形成机理及PDA快速沉积表面化学的最新研究进展进行了总结,在此基础上综述了近10年PDA涂层材料在开管毛细管电色谱（OT-CEC）和毛细管电色谱整体柱中的最新应用。此外,还对PDA涂层材料在CEC中的发展方向进行了展望。     

Capillary Electrophoresis Immunoassay for 2, 4-Dichlorophenoxyacetic Acid

ABSTRACT

A capillary electrophoresis (CE) immunoassay format for 2, 4-dichlorophenoxyacetic acid (2, 4-D) is demonstrated. A fluorescent labeled 2, 4-D analog competes with the analyte of interest for a finite number of binding sites provided by anti-2, 4-D monoclonal antibodies. CE then provides a means of separating and measuring both the free and antibody-bound fluorescent tracer using laser-induced fluorescence detection. For this assay format, the amount of free tracer is a sensitive indicator for the concentration of analyte present in the sample. A sequential injection format allows the rapid analysis of a small number of samples. The dynamic concentration range for 2, 4-D in either buffer or river water is 5 ppb to 1000 ppb.     

开管毛细管电色谱分析3种解热镇痛药物

针对生物体液样品开展药物的绿色高效毛细管电泳分离分析具有重要的研究意义。该研究以3种解热镇痛药（4-氨基安替比林、氨基比林及非那西汀）为研究对象,以嵌段聚合物为涂层,建立了药物的开管毛细管电色谱（OT-CEC）分析新策略。首先,采用活性/可控自由基可逆加成-断裂链转移聚合方法,合成制备得到了两亲性嵌段聚合物-聚（苯乙烯-甲基丙烯酸缩水甘油酯）（P（St-GMA））,并将其涂覆到毛细管内壁;其次,通过考察影响OT-CEC分离效率的关键因素,包括嵌段聚合物的聚合时间、涂覆毛细管嵌段聚合物的浓度、电泳运行缓冲液的种类和pH值、有机溶剂添加剂等,优化了3种解热镇痛药物的OT-CEC分离条件;最终发现,不需添加任何有机溶剂及表面活性剂,仅采用50.0 mmol/L乙酸钠-乙酸（pH 5.7）作为OT-CEC的缓冲溶液,就能实现3种解热镇痛药物的基线分离。在8.0~2.5×10³ μmol/L范围内,分析物峰面积与其对应的浓度呈现良好的线性关系,相关系数（R²）均大于0.995,检出限为1.0~2.5 μmol/L。结果表明：P（St-GMA）在溶液中自组装所形成的类表面活性剂胶团结构增强了两亲性嵌段聚合物与解热镇痛药物之间的相互作用,显著提升了解热镇痛药物的OT-CEC分离效率。该工作不仅为制备新型聚合物及调控嵌段聚合物的自组装行为提供了研究思路,也展示了两亲性嵌段聚合物在药物的绿色OT-CEC分析中的实际应用潜力。     

Determination of thiols by capillary micellar electrokinetic chromatography with laser induced fluorescence detection using 1,3,5,7‐tetramethyl‐8‐phenyl‐(4‐iodoacetamido) difluoroboradiaza‐s‐indacene as labeling reagent

A sensitive and effective micellar electrokinetic capillary chromatography with laser‐induced fluorescence detection approach was described for the determination of low molecular‐mass thiols using 1,3,5,7‐tetramethyl‐8‐phenyl‐(4‐iodoacetamido) difluoroboradiaza‐s‐indacene as the labeling reagent. After precolumn derivatization, baseline separation of six thiol compounds including cysteine, glutathione, N‐acetylcysteine, homocysteine, 6‐mercaptopurine, and penicillamine were achieved within 18 min. The optimal running buffer was composed of mixtures involving 25 mM sodium dodecyl sulfate, 25% (v/v) acetonitrile and 15 mM sodium phosphate buffer, pH 7.5. The detection limits (S/N = 3) were found as low as 40 pM under argon ion laser‐induced fluorescence detector (λ_ex/λ_em = 488/520 nm), which were much better than the reported approaches. The accuracy and specificity of this assay for real samples were assured by a standard addition method. The proposed method has been applied to the analysis of thiols both in human plasma and plum flower samples with recoveries of 92.0–109.4%.