Critical comparison of automated purge and trap and solid-phase microextraction for routine determination of volatile organic compounds in drinking waters by GC-MS

The use of two automated sample preparation techniques, solid-phase microextraction (SPME) and purge and trap (P&T) systems are critically compared for the GC–MS determination of eight volatile organic compounds (VOCs), including trihalomethanes (THMs), in drinking water samples. Compounds chosen for the comparison are regulated by Spanish and European official guidelines for drinking waters. Experimental parameters investigated for the two sample preparation techniques included SPME type of fibers, SPME modality, P&T gas flow, extraction and desorption times and desorption temperatures. Thus, optimal experimental conditions have been worked out for the SPME and P&T techniques. Under such optimised conditions, detection limits, precision and accuracy were evaluated. Both methods fulfilled the values that the official guidelines establish. The P&T–GC–MS method offers LDs ranged from 0.004 to 0.2 ng mL⁻¹, repeatabilities below 6% and recoveries between 81 and 117%; while LDs ranging from 0.008 to 0.7 ng mL⁻¹, 1–12% R.S.D. and recoveries from 80 to 119% were achieved with the SPME–GC–MS method. Finally, we chose P&T–GC–MS method as the best for this determination and we validate this methodology by its application to the analysis of an Aquacheck Interlaboratory Exercise.     

Determination of 19 volatile organic compounds in wastewater effluents from different treatments by purge and trap followed by gas-chromatography coupled to mass spectrometry

A rapid and simple methodology based on purge and trap with gas-chromatography coupled to triple quadrupole mass spectrometry has been developed for the analysis of 19 volatile organic compounds (VOCs) in wastewater (WW) effluents from four different treatments. The determination was carried out in the raw WW effluents, which were not submitted to any pre-treatment (e.g., filtration). A matrix effect study was also performed, concluding that solvent calibration was adequate to quantify VOCs in WW effluent samples containing a variety of suspended particulate matter. Adequate validation parameters were obtained with recovery values in the range 73–124% and precision values lower than 24%. Limits of quantification were established at 0.1 μg L^-1 for all VOCs. The proposed method was applied to the analysis of WW samples, detecting chloroform and toluene at concentrations ranging from 0.1 to 4.80 μg L^-1.     

Novel multi-sorbent for sampling and determination of trace volatile organic sulfur compounds in ambient air

Novel adsorbent APSG-MW (average particle size 215?µm and specific surface 98 m²?g^?1) bonding multi-walled carbon nanotubes (MWCNTs) on silica gel are obtained. Then the sampling tubes filled with Tenax TA and APSG-MW are prepared and the adsorptive capacity of Tenax TA/APSG-MW for volatile organic sulfur compounds (VOSCs) is studied. The data show that the adsorption and desorption recoveries of multi-sorbent for VOSCs are satisfactory (>85%), and the breakthrough values are large (>16?L?g^?1) enough to absorb VOSCs in ambient air. The sampling precision of the sorbent tubes meets TO-17 criteria. The sampling tubes are successfully used to concentrate and analyze a sample of landfill air, and the major S compounds are identified.     

Multicomponent analysis of volatile organic compounds in water by automated purge and trap coupled to gas chromatography-mass spectrometry

Experiments and molecular simulations were carried out to study temperature effects (in the range of 323 to 383 K) on the absolute and relative retention of n-hexane, n-heptane, n-octane, benzene, toluene and the three xylene isomers in gas-liquid chromatography. Helium and squalane were used as the carrier gas and retentive phase, respectively. Both the experiments and the simulations show a markedly different temperature dependence of the retention for the n-alkanes compared to the arenes. For example, over the 60 K temperature range studied, the Kovats retention index of benzene is found to increase by about 16 or 18+/-10 retention index units determined from the experiments or simulations, respectively. For toluene and the xylenes, the experimentally measured increases are similar in magnitude and range from 14 to 17 retention index units for m-xylene to o-xylene. The molecular simulation data provide an independent method of obtaining the transfer enthalpies and entropies. The change in retention indices is shown to be the result of the larger entropic penalty and the larger heat capacity for the transfer of the alkane molecules.     

Determination of volatile organic compounds in contaminated air using semipermeable membrane devices

Semipermeable membrane devices (SPMDs) were evaluated as passive samplers for the determination of 26 volatile organic compounds (VOCs) in contaminated air of occupational environments. A direct methodology based on the use of head-space-gas chromatography-mass spectrometry (HS-GC-MS) was developed for VOCs determinations in SPMDs, without any sample pre-treatment and avoiding the use of solvents. A desorption temperature of 150 °C for 10 min was sufficient for a sensitive VOCs determination providing limits of detection in the range of 15 ng SPMD⁻¹ for 21 of 26 studied compounds. Linear and equilibrium uptake models were established for each VOC from compound isotherms. Highly volatile compounds were slightly absorbed and moderately volatile compounds were strongly absorbed by SPMDs. This study is the first precedent of the use of SPMDs for the simultaneous sampling of a wide number of VOCs. The use of SPMDs is a simple and low cost alternative to ordinary sampling devices such as Radiello^® diffusive samplers or badge-type solid-phase supports.     

In situ determination of organic compounds in liquid samples using a combined UV-Vis/fluorescence submersible sensor

In order to improve the in situ evaluation and quantitative analysis of complex contaminations of liquid media such as ground-, surface, and wastewaters, an integrated submersible sensor probe has been developed. It is especially characterized by the option of simultaneously measuring ultraviolet/visible (UV/Vis) and fluorescence spectra. Owing to the compact construction with light sources, flow cell, detection system, and data acquisition/processing unit in the waterproof case, the data transfer to the surface can be realized electrically, and the operation depth is practically not limited. The variability in the measuring techniques allows a wide variety of chemical compounds to be analysed within a broad concentration range. The performance of the new submersible sensor probe was tested ex situ in laboratory scale, and the performance was comparable with that of stationary measuring instruments. As an example for an in situ application, the sensor probe was successfully used to monitor the migration of chemical substances during a tracer experiment in groundwater. The concentration of the tracer compound uranin (sodium fluorescein) was measured in the range of 5–500 µg L^?1 using fluorescence spectroscopy, while at the same time the contents of toluene were continuously detected in the same groundwater wells using the UV/Vis sensor channel.     

Instrument for generation of volatile organic compounds for the development of chemical sensors and evaluation of tube-type diffusive sampling

An automatic calibration apparatus for the dynamic generation of organic vapours was developed. The accurately controlled stream of nitrogen was drawn at a low flow-rate through a thermostated container filled with the standard substance, thus generating a continuous stream of saturated vapour of the compound. The compound holder vessel was thermostated at −16°C. A large stream of pure carrier gas was mixed with a low stream of substance in a mixing chamber for dilution. The fittings were manufactured from PTFE, and tubes were made of special PTFE with an inert inner surface to eliminate the wall adsorption and to decrease the cross-diffusion. Moisture interferences were reduced using a Nafion membrane filter. The vapour generator was validated by diffusive sampling and gas chromatographic methods. Standard mixtures have been prepared containing toluene at concentrations ranging from 3 to 3000 ppm. The combined uncertainty of preparative and analytical error components associated with the concentration of the analytes at the 95% confidence level typically ranges from 2 to 5% relative, depending upon the concentration. The measured and the calculated values were compared and good correlation (r²>0.99) was found.     

Fabrication of novel nanoporous array anodic alumina solid-phase microextraction fiber coating and its potential application for headspace sampling of biological volatile organic compounds

In the study, nanoporous array anodic alumina (NAAA) prepared by a simple, rapid and stable two-step anodic oxidization method was introduced as a novel solid-phase microextraction (SPME) fiber coating. The regular nanoporous array structure and chemical composition of NAAA SPME fiber coating was characterized and validated by scanning electron microscopy and energy dispersive spectroscopy, respectively. Compared with the commercial polydimethylsiloxane (PDMS) SPME fiber coating, NAAA SPME fiber coating achieved the higher enrichment capability (1.7–4.7 folds) for the mixed standards of volatile organic compounds (VOCs). The selectivity for volatile alcohols by NAAA SPME fiber coating demonstrated an increasing trend with the increasing polarity of alcohols caused by the gradually shortening carbon chains from 1-undecanol to 1-heptanol or the isomerization of carbon chains of some typical volatile alcohols including 2-ethyl hexanol, 1-octanol, 2-phenylethanol, 1-phenylethanol, 5-undecanol, 2-undecanol and 1-undecanol. Finally, NAAA SPME fiber coating was originally applied for the analysis of biological VOCs of Bailan flower, stinkbug and orange peel samples coupled with gas chromatography–mass spectrometry (GC–MS) detection. Thirty, twenty-seven and forty-four VOCs of Bailan flower, stinkbug and orange peel samples were sampled and identified, respectively. Moreover, the contents of trace 1-octanol and nonanal of real orange peel samples were quantified for the further method validation with satisfactory recoveries of 106.5 and 120.5%, respectively. This work proposed a sensitive, rapid, reliable and convenient analytical method for the potential study of trace and small molecular biological VOCs by the novel NAAA SPME fiber coating.     

Stability of workroom air volatile organic compounds on solid adsorbents for thermal desorption gas chromatography

The storage stability of the occupationally frequently occurring compounds, methylethylketone, methylisobutylketone, benzene, toluene, tetrachloroethylene, n-butylacetate, -pinene, β-pinene, limonene and n-decane, has been investigated on the adsorbents Tenax TA, Chromosorb 106 and Carbotrap using thermally desorbable tube type samplers, commonly utilized in ambient and workroom atmospheric measurements. Fifty and 500 ng of each compound were loaded on the various adsorbents tubes, stored at both ambient (20 °C) and refrigerated (4 °C) temperatures and analysed by means of thermal gas chromatography with mass spectrometric detection on days 0, 7, 14 and 28 after exposure. A 90% storage recovery was chosen as acceptance criteria for storage stability, and statistical testing by Student's t-test, analysis of variance and Bonferroni post hoc tests were employed to investigate the effect of the categorical variables storage time, storage temperature and analyte loading on the different adsorbents. Chromosorb 106 showed the overall best behaviour with recoveries of 90% or better for all analytes during the 28-day test period. Tenax TA and Carbotrap yielded lower recoveries and were more influenced by variations in storage time, storage temperature and analyte loading. Refrigerated temperatures were best avoided for storage on Tenax TA, but may increase the recovery of some compounds on Carbotrap (e.g. n-butylacetate). The blank build-up on the adsorbents was also investigated, and Carbotrap and Tenax TA showed no signs of artefact development over time. Chromosorb 106, however, contained inherently more artefacts that build up over time, which in spite of the excellent storage capability, may limit its use in field studies where long storage times are normal.     

Low temperature sampling techniques for the determination of less volatile compounds in gaseous mixtures

Summary The analysis of trace quantities of the less volatile polar compounds (H₂O, NH₃, HCN, amines, alcohols, esters etc.) is frequently seriously affected by dubious sampling procedures. In the present contribution two different sampling techniques at dry ice temperature (195 K) are described which both claim considerable and predictable efficacy. Depending on whether the matrices of the samples are still gaseous or condensable at 195 K and ambient pressure, a scrubbing technique may be used or condensation in the presence of a suitable solvent with subsequent evaporation of the matrix. Some solvents and solvent mixtures with FP<195 K are compiled. The normally disadvantageous low volatility can be exploited for enrichment. The scrubbing technique enables detection limits of 1 ppb(V/V) to be achieved, the condensation technique 1 ppm(m/m). Simple checking methods for both techniques are described. Thermodynamic considerations for ideal mixtures enable the calculation of upper limits for possible deviations. Examples are presented.Presented at the 14th International Symposium on Chromatography London, September, 1982     

Sampling and determination of volatile organic compounds with needle trap devices

In this study, a sorbent was immobilized inside a needle resulting in the development of a needle trap (NT) device. This device was applied to extract organic components from gaseous samples and to introduce an enriched mixture into a conventional gas chromatography (GC) injector. Construction of this simple and integrated sampling/extraction/sample introduction device was optimized by considering different ways to immobilize a sorbent in the needle, packing single and multiple-layer sorbent beds, and applying different desorption strategies into the GC injector. A carrier gas system was modified to minimize the carryover for the needle trap with a sealed tip (NT-1), and a narrow-neckliner was used for the blunt-tip needle trap (NT-2). Breakthrough in the device was investigated by connecting two NT-2 devices in series. The needle trap performed very well as an exhaustive spot sampler, as well as in a time-weighted average (TWA) operation. The linear velocity of the mobile phase has no influence on the sampling rate of the needle trap. Validation results against the standard NIOSH 1501 method using charcoal tubes for indoor air surveys demonstrated good accuracy for the NT approach. The reproducibility of the NT-2 was about 1% for benzene. The detection limits for FID detection and for 25 ml gas sample were 0.23 ng/l, 2.10 ng/l and 1.12 ng/l for benzene, ethylbenzene and o-xylene, respectively.     

Sorbent-based sampling methods for volatile and semi-volatile organic compounds in air. Part 2. Sorbent selection and other aspects of optimizing air monitoring methods

Sorbent tubes/traps are widely used in combination with gas chromatographic (GC) analytical methods to monitor the vapour-phase fraction of organic compounds in air. Applications range from atmospheric research and ambient air monitoring (indoor and outdoor) to occupational hygiene (personal exposure assessment) and measuring chemical emission levels. Part 1 of this paper reviewed the main sorbent-based air sampling strategies including active (pumped) tube monitoring, diffusive (passive) sampling onto sorbent tubes/cartridges plus sorbent trapping/focusing of whole air samples that are either collected in containers (such as canisters or bags) or monitored online. Options for subsequent extraction and transfer to GC(MS) analysis were also summarised and the trend to thermal desorption (TD)-based methods and away from solvent extraction was explained. As a result of this trend, demand for TD-compatible sorbents (alternatives to traditional charcoal) is growing. Part 2 of this paper therefore continues with a summary of TD-compatible sorbents, their respective advantages and limitations and considerations for sorbent selection. Other analytical considerations for optimizing sorbent-based air monitoring methods are also discussed together with recent technical developments and sampling accessories which have extended the application range of sorbent trapping technology generally.     

Strategies for monitoring the emerging polar organic contaminants in water with emphasis on integrative passive sampling

Although polar organic contaminants (POCs) such as pharmaceuticals are considered as some of today's most emerging contaminants few of them are regulated or included in on-going monitoring programs. However, the growing concern among the public and researchers together with the new legislature within the European Union, the registration, evaluation and authorisation of chemicals (REACH) system will increase the future need of simple, low cost strategies for monitoring and risk assessment of POCs in aquatic environments. In this article, we overview the advantages and shortcomings of traditional and novel sampling techniques available for monitoring the emerging POCs in water. The benefits and drawbacks of using active and biological sampling were discussed and the principles of organic passive samplers (PS) presented. A detailed overview of type of polar organic PS available, and their classes of target compounds and field of applications were given, and the considerations involved in using them such as environmental effects and quality control were discussed. The usefulness of biological sampling of POCs in water was found to be limited. Polar organic PS was considered to be the only available, but nevertheless, an efficient alternative to active water sampling due to its simplicity, low cost, no need of power supply or maintenance, and the ability of collecting time-integrative samples with one sample collection. However, the polar organic PS need to be further developed before they can be used as standard in water quality monitoring programs.     

Determination of volatile organic compounds in human breath for Helicobacter pylori detection by SPME-GC/MS

Helicobacter pylori living in the human stomach release volatile organic compounds (VOCs) that can be detected in expired air. The aim of the study was the application of breath analysis for bacteria detection. It was accomplished by determination of VOCs characteristic for patients with H. pylori and the analysis of gases released by bacteria in suspension. Solid-phase microextraction was applied as a selective technique for preconcentration and isolation of analytes. Gas chromatography coupled with mass spectrometry was used for the separation and identification of volatile analytes in breath samples and bacterial headspace. For data calculation and processing, discriminant and factor analyses were used. Endogenous substances such as isobutane, 2-butanone and ethyl acetate were detected in the breath of persons with H. pylori in the stomach and in the gaseous mixture released by the bacteria strain but they were not identified in the breath of healthy volunteers. The canonical analysis of discrimination functions showed a strong difference between the three examined groups. Knowledge of substances emitted by H. pylori with the application of an optimized breath analysis method might become a very useful tool for noninvasive detection of this bacterium.     

On-line microdialysis sampling coupled with flame atomic absorption spectrometry for continuous in vivo monitoring of diffusible magnesium in the blood of living animals

A novel on-line microdialysis sampling coupled with flame atomic absorption spectrometry (FAAS) with an attractive application is reported. Microdialysates perfused through implanted microdialysis probes were directly introduced into the flame atomizer of a FAAS system using 0.2% HNO₃ as carrier solution at a nebulizer uptake flow rate of 6 ml min⁻¹. The interval for each determination was 90 s (60 s sampling time, 10 s read time and 20 s washing time). The analytical characteristics of the on-line microdialysis-FAAS system were validated as follows: linearity range, 0-300 mg l⁻¹; detection limit (3σ, n = 7), 0.53 mg l⁻¹; precision (R.S.D., n = 50), 4.1%. By comparing Mg levels in the blood of living rabbits with the results obtained from in vivo no net flux (NNF) method, the accuracy of the proposed on-line method was found to be good. The present method can be successfully applied to the in vivo monitoring of diffusible Mg in the blood of living rabbits after magnesium sulfate (MgSO₄) administration with a temporal resolution of 1.5 min.     

Optimization of in situ derivatization SPME by experimental design for GC-MS multi-residue analysis of pharmaceutical drugs in wastewater

This paper presents the development of a procedure, which enables the analysis of nine pharmaceutical drugs in wastewater using gas chromatography‐mass spectrometry (GC‐MS) associated with solid‐phase microextraction (SPME) for the sample preparation. Experimental design was applied to optimize the in situ derivatization and the SPME extraction conditions. Ethyl chloroformate (ECF) was employed as derivatizing agent and polydimethylsiloxane‐divinylbenzene (PDMS‐DVB) as the SPME fiber coating. A fractional factorial design was used to evaluate the main factors for the in situ derivatization and SPME extraction. Thereafter, a Doehlert matrix design was applied to find out the best experimental conditions. The method presented a linear range from 0.5 to 10 μg/L, and the intraday and interday precision were lower than 16%. Applicability of the method was verified from real influent and effluent samples of a wastewater treatment plant, as well as from samples of an industry wastewater and a river.     

Analysis of volatile organic compounds in wastewater during various stages of treatment for high-tech industries

Summary A protocol combining purge-and-trap (P&T) and solid-phase microextraction (SPME) was established for the analysis of volatile organic compounds (VOCs) in the wastewater plant of high-tech industries. Over 60 VOCs could be analyzed by P&T coupled to gas chromatography/mass spectrometry (P&T-GC-MS). Four polar VOCs commonly used in the high-tech industries were determined by SPME coupled to gas chromatography/flame ionization detection (SPME-GC-FID). The limits of detection for the analytes were less than 1.1 μg L⁻¹ with P&T-GC-MS, and between 1.5 and 12.5 μg L⁻¹ with SPME-GC-FID. Satisfactory recoveries (83% to 130%) were obtained. Real samples were analyzed from a wastewater treatment plant during various stages of treatment. The major pollutant in the wastewater influent was found to be acetone (>4 ppm).     

A simple and fast sampling method for the characterization of volatile compounds released byNezara viridula

Summary A simple method is described for the collection of volatile compounds from a biological matrix and for their subsequent GC-MS analysis. (E)-2-decenal and (E)-2-decenyl acetate odorous compounds from bugs of theNezara viridula species were detected together with n-dodecane and n-tridecane hydrocarbons as carriers. The chemical composition of the secretions of the bugs collected in the Veneto region corresponds to one obtained from the same American pentatomidae.