基于垂直结构的有机光发射晶体管制备与性能研究

制备了一种有机垂直光发射晶体管, 兼具有机发光二极管的发光和晶体管的开关调节两个功能.其结构为一个有机发光单元垂直堆叠在一个电容单元上,两单元通过一个共有的源电极连在一起.当电容单元被充电时,积累在源电极的电荷能有效地调节源极与有机层之间的载流子注入势垒,从而达到控制源漏输出电流的大小,最终控制发光单元发光的强度.实验结果表明,器件可提供02 mA的输出电流,其大小可驱动发光单元发光,工作电压（开启电压）为6 V.这种垂直集成方案,实现了器件多功能化,为有机发光二极管有源矩阵驱动的实际应用提供了一种新的解决方法. 关键词： 有机光发射晶体管 垂直 电容     

基于NPB的垂直构型有机发光晶体管的光电特性研究

通过将有机空穴阻挡材料BCP薄层插入垂直构型有机发光晶体管器件ITO/NPB（40nm）/Al（30nm）/NPB（20nm）/Alq₃（55nm）/Al中的不同位置对器件光电特性的影响来研究器件漏电流较大的原因以及器件中具体的载流子过程.充分证明了栅极注入的空穴对沟道中的电流有贡献.进而通过用LiF薄层修饰漏极来增强电子的注入并减小漏电流,得到了相对稳定的发光晶体管器件,其发光强度有很大提高并可很好地由栅极电压来进行调控.更换发光材料层容易得到不同颜色的发光晶体管. 关键词： 垂直构型有机发光晶体管（VOLET） 静电感应晶体管（SIT） N')" href="#">NPB （N N′-diphenyl-N')" href="#">N′-diphenyl-N N′-bis（1-naphtyl）-1')" href="#">N′-bis（1-naphtyl）-1 1′-biphenyl-4     

基于LPC2210和SSD1339的PM-OLED驱动控制电路

为了避免早期无源矩阵有机电致发光器件驱动控制电路的一些缺陷,如:"串扰"和"交叉"效应以及电路连接比较复杂,用两种方法实现了基于飞利浦公司生产的LPC2210控制芯片和晶门科技公司的SSD1339驱动芯片的驱动控制电路。首先介绍了有机电致发光器件的结构和发光原理以及芯片SSD1339和LPC2210的主要的特点;分析和比较了SSD1339的8080系列并行口和LPC2210外部存储控制单元的读写时序;分别利用LPC2210的通用输入输出单元和外部存储控制单元,成功的控制SSD1339驱动128RGB×128点阵有机电致发光屏。实验结果表明:两种方法不仅可以有效地克服早期驱动控制电路的缺陷,而且可以使有机电致发光屏显示出高质量的图片;用外部存储控制单元实现的驱动控制电路,可以实现约80 Hz的驱动帧频;而使用通用输入输出单元实现的驱动控制电路,可以单步跟踪数据的传输,因此它具有方便查错的优势。本次实验为在不同的集成环境下无源矩阵有机电致发光器件驱动控制电路的设计奠定基础。     

交流驱动无电学接触GaN基Micro-LED器件光电特性

针对Micro-LED器件微型化带来的尺寸效应、高速巨量转移、发光器件与驱动背板的高精度键合等问题,本文通过金属有机化学气相沉积和原子层沉积技术制备了一种垂直结构的交流驱动无电学接触型GaN基Micro-LED器件,研究了其光电特性。结果表明,器件电路模型可等效为RC电路,随着交流驱动信号频率的增大,器件等效阻抗先快速减小后趋于稳定。当频率固定时,器件I-V特性呈线性关系,器件等效阻抗稳定,器件亮度随着驱动电压增大而增强。当驱动电压固定时,器件在16～22 MHz频率范围内达到最大亮度,且亮度随频率增加呈现先上升后下降趋势;此外,由于回路呈电容特性,无电学接触型Micro-LED器件存在发光延迟效应和电流超前效应。对比传统Micro-LED器件,无电学接触型Micro-LED器件与外部电极无电学接触,在交流驱动条件下实现内部载流子复合发光,有望解决Micro-LED芯片微型化带来的技术难题。     

微电流高效率650nm谐振腔发光二极管

基于微腔理论和薄膜光学传输矩阵模型,设计并制备了孔径不同的谐振腔发光二极管.通过对外延结构的设计和对器件的制备与测试,详细研究了微腔结构、腔谱失谐以及有效辐射面积对器件发光效率、峰值波长和半波全宽等性能的影响,最终降低了器件的启亮电流并且提升了器件的外量子效率.制备的器件能够在100μA偏置电流下产生肉眼清晰可见的微瓦级光强,在1mA电流下达到0.16mW的光功率和7%的外量子效率.器件的峰值波长为650nm,并且在0.1~7mA范围内不随电流改变而发生变化.远场分布为均匀对称的圆形光斑,水平和竖直发散角分别为46°和48°.与普通发光二极管相比,该器件具有更高的发光效率和更好的单色性、方向性、波长稳定性,研究成果为实现微小电流驱动的高亮度发光器件提供了基础元件,并为谐振腔发光二极管在微电流下的光电特性研究提供参考与借鉴.     

非晶硅碳薄膜发光二极管发光的热致猝灭

本文详细测试了用RF-PECVD法制备的非晶硅碳薄膜发光二极管的光强电流特性和温度对器件发光强度的影响.在直流电流驱动下,器件的发光在注入电流1A/cm2左右趋于饱和,而在低占空比的脉冲电流驱动下器件的发光直至注入电流20A/cm2仍随电流近似线性增长,但提高环境温度发光随之下降.结合对器件受热情况分析表明,热致猝灭而非场致猝灭导致了器件在大电流下的发光饱和,并简要提出了改进器件散热的措施.     

莱纳(发光、接收光器件)

莱纳的概况 “LANER”(莱纳)是一种具有开关和发光两种性能的光半导体器件。这个单一的器件,同时具有接收光和发光的机能。它不但具有非线性特性(或负阻特性)控制机能,同时还能用可见光、红外线或同时用这两种光的波长来驱动控制。莱纳不仅可以在常温下工作,并且还可用莱纳中发光二极管的输出光来驱动器件本身。因此,实现了所说的“光的互相作用”。     

蓝色荧光有机发光二极管中的激子-电荷相互作用

有机发光二极管(OLED)作为新一代显示技术已广泛商用,但蓝光有机发光二极管在效率和稳定性等方面仍存在不足,虽用磷光染料能明显地提高效率,其制作成本之高却限制了产业化发展.因此,本文对蓝色荧光有机发光二极管中的效率滚降现象进行了深入探究.首先,从稳态和瞬态两个角度研究了电子电流和空穴电流对单极器件光致发光行为的影响,表明空穴对激子的淬灭效果更显著.实验证明激子-电荷相互作用是荧光OLED中效率滚降的主要机制,且激子主要是被束缚电荷淬灭而非移动电荷.另一方面制备了不同掺杂浓度的有机发光二极管器件以探究掺杂浓度对激子-极化子相互作用的影响,得到了综合性能较好的蓝色有机荧光器件,分析表明调控发光层电荷俘获可以平衡界面堆积电荷和发光层束缚电荷对激子的淬灭.本文完善了激子-极化子淬灭的内在机制,给减缓蓝色荧光有机发光二极管的效率滚降提供了有益参考.     

基于自动跟踪LED驱动电压控制电路的创新设计

LED发光二极管在发光时约有80%以上的功率转化成了热能,导致LED发光二极管的PN结温度过高,这是影响LED发光二极管的发光效率与照明功能的主要因素。本文针对上述问题,结合现实情况,设计了一种自动跟踪LED驱动电压的控制电路,从串联稳流单元采样一个电压信号,与本控制电路中的基准电压相比较,产生一个控制信号,去控制所述串联稳流单元前级的开关稳压电源,使它的输出电压随LED灯的工作电压的变化而变化,不增加调整管的功耗。避免了常见的恒压驱动亮度变化大的缺陷,从而大幅度提高LED发光二极管的工作效率,该控制电路结构简单、成本低、损耗小与可靠性高。     

可调色红光有机电致发光器件

介绍了具有可调节发光光谱的高效红光有机发光二极管(OLED)器件,利用具有高三重态能量的9.9-螺二芴二苯基氧化磷(SPPO1)作为发光层的主体材料及空穴阻挡层,二(1-苯基异喹啉)(乙酰丙酮)合铱(III) (Ir(piq)2(acac))作为客体发光材料,在发光层内SPPO1的能量分别由福斯特和迪克斯特传递到Ir(piq)2(acac)的单重态和三重态从而发出红色磷光,通过调节磷光客体材料的比例得到最优器件结构,从而得到具有较好发光效率和发光亮度并可调节色纯的有机发光二极管器件。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.