TiO2/SnO2复合光催化剂的耦合效应

采用改进的sol gel技术制备TiO2/SnO2耦合型半导体光催化剂,利用XRD、气相色谱 仪、粒度仪和表面光电压装置等研究了耦合型半导体光催化机理和光催化效率的影响因素, 并通过降解甲醛探讨其在空气污染治理中的作用.实验结果表明,添加20 ％(mol) SnO2的复 合半导体光催化剂,其光催化效率比纯TiO2高一倍以上.据实验结果和粒子紧密堆积原理,提 出强耦合效应和弱耦合效应的光催化反应模型,并用此模型较好地解释了TiO2/SnO2复合型半 导体光催化剂的光催化效率随SnO2含量变化规律.     

高电化学活性SnO2/TiO2空心微球的制备及其性能

采用一种简便的无模板溶剂热法合成了尺寸在1μm左右、具有堆叠结构的SnO_2/TiO_2空心微球。合成过程的研究结果表明:SnO_2/TiO_2空心微球在形成过程中经历了空心、被填充、分裂到再次形成空心结构的过程。随后,SnO_2/TiO_2空心微球作为锂离子电池负极材料的电化学性能测试结果表明:SnO_2/TiO_2空心微球在0.1 A·g~(-1)的电流密度下,其首次放电容量达到1 484.9mAh·g~(-1),库伦效率为49.0%。经过600次循环后,其放电容量依然可以达到565.6 mAh·g~(-1),显示了高的容量和循环稳定性。     

Catalytic oxidation of no to NO2 over Cr/TiO2 and Cu/TiO2 under oxidizing atmosphere

The catalytic activity of Cr/TiO₂ and Cu/TiO₂ for the oxidation of NO under an oxidizing atmosphere has been examined. Both catalysts had excellent ability for the oxidation of NO to NO₂ in the temperature range of 350–400°C.     

Hydrogen desorption of reduced Pt/TiO2 catalyst

The temperature-programmed desorption of hydrogen from a Pt/TiO₂ catalyst reduced in a wide temperature range (RT-773 K) has been studied. It is found that the presence of labile surface oxygen species increases the amount of hydrogen species formed at room temperature, and greatly decreases the quantities of adsorbed hydrogen species at medium temperatures. After the catalyst was reduced at high temperature, it is observed that two strong hydrogen desorption peaks appear at 450–600 K and above 600 K, which are ascribed to surface titanium hydride and the hydrogen species stored in the sublayer and bulk of the support, respectively.     

SnO_2改性TiO_2对V_2O_5-WO_3/TiO_2催化剂结构和SCR性能影响

采用共沉淀法将SnO_2组分掺入到V_2O_5-WO_3/TiO_2催化剂载体TiO_2中,并通过多种物理化学手段,考察了不同SnO_2掺入量时对催化剂结构,表面分散物种和SCR性能影响.结果表明,SnO_2掺入到TiO_2中,元素Sn与Ti以Sn—O—Ti键形式相互作用,促进锐钛矿型TiO_2向金红石型TiO_2转变.在特定条件下,VO_x与WO_x物种和SnTi氧化物之间以V—O—Ti(Sn)和W—O—Ti(Sn)键形式相互作用,提高了VO_x物种可还原能力、促进了具有更多B酸酸量四面体WOx物种和V~(5+)物种生成.VW/SnTi催化剂表面VO_x物种与WO_x物种之间的相互作用更强.因此,VW/SnTi催化剂具有更好的SCR活性.     

Phase transformations in nanocrystalline TiO2 milled in different milling atmospheres

The structural evolution of nanocrystalline TiO₂ milled in different milling atmospheres was studied by X-ray diffraction (XRD), Raman spectroscopy and X-ray photoelectron spectroscopy. Rietveld refinements of the XRD data showed that high-energy ball milling induced the transformations from anatase to srilankite and rutile at room temperature and ambient pressure. The milling atmospheres with different oxygen partial pressures had an influence on the transformation kinetics of anatase. When the nanocrystalline TiO₂ powders were, respectively, milled in oxygen, air and nitrogen atmospheres, the transformation rates of anatases in turn increased with a decrease in oxygen partial pressure of the milling atmosphere, due to the reducing concentration of oxygen vacancies in the milled TiO₂ lattice.     

溶剂热氧化少层Ti3C2 MXene制备二维TiO2/Ti3C2复合光催化剂

为了改善TiO_2光催化剂光生电子-空穴对复合率高、太阳光利用率低的缺陷,采用溶剂热法控制氧化剥离的少层Ti_3C_2MXene(DL-Ti_3C_2),制备TiO_2/DL-Ti_3C_2复合光催化剂,并通过降解罗丹明B溶液,研究其光催化性能。结果表明,TiO_2/DL-Ti_3C_2复合光催化剂能有效吸收可见光,且光催化性能明显优于DL-Ti_3C_2和P25。当溶剂热氧化温度为160℃时,复合材料具有最佳的光催化性能。当氧化温度过低时,催化剂中形成的TiO_2量不足,产生的光生电子-空穴对数量较少,导致催化剂性能较差;当氧化温度过高时,DL-Ti_3C_2减少,降低了材料导电性,光生电子-空穴对复合效率高,导致催化剂性能变差。因此,通过改变DL-Ti_3C_2的氧化温度,可以调控TiO_2/DL-Ti_3C_2复合材料中TiO_2和DL-Ti_3C_2的相对含量,使二者产生协同作用提高复合光催化剂的可见光催化活性。     

Low temperature CO oxidation on Au/TiO2 sol-gel catalysts

A comparative study on Au/TiO₂catalysts prepared by impregnation with HAuCl₄of commercial TiO₂ or by impregnation of sol-gel derived TiO₂has been carried out during CO oxidation. Specific surface areas and mean Au particle of 49 and 74 m²/g and 35 and 25 Å were obtained for impregnated commercial TiO₂ and sol-gel preparations, respectively. XRD patterns shown that in sol-gel derived TiO₂ only anatase phase was identified, while in commercial TiO₂ anatase and rutile phases co-exist. Titania support effect on Au activity for the oxidation of CO has been observed. The light-off during the reaction on Au/TiO₂initiates at 50°C, whereas for commercial impregnated TiO₂ catalyst the light-off initiates at 200°C.     

Increased promotion by deposition of Co acetylacetonate over sulphided Mo/TiO2 hydrodesulphurization catalyst

CoMo/TiO₂ catalysts prepared by deposition of Co acetylacetonate on presulphided Mo/TiO₂ catalyst in methanol exhibited higher promotion of hydrodesulphurization activity than catalysts prepared by conventional impregnation of Mo/TiO₂ by a solution of Co nitrate.     

CeO2改性Ag-V2O5/TiO2催化剂的甲基吡啶氧化脱甲基性能

以锐钛矿TiO_2为载体,考察了CeO_2改性对Ag-CeO_2-V_2O_5/TiO_2催化3-甲基吡啶氧化脱甲基性能的影响,并优化了催化剂组成与制备条件.结果表明:Ce掺杂改性不仅能够与V物种作用形成Ce VO_4,而且促进V_2O_5分散,改善活性组分的氧化还原性能,从而提高3-甲基吡啶脱甲基转化率与选择性,改善Ag-V_2O_5/TiO_2催化性能.适宜的催化剂组成为V_2O_5负载量15%,Ce/V的摩尔比0.33,Ag质量分数1.0%.过高的焙烧温度将导致TiO_2载体向金红石型转变,Ag-CeO_2-V_2O_5/TiO_2适宜制备条件为450℃焙烧4 h.     

TiO2/蒙脱石纳米复合物中TiO2的结构相变

以钛酸丁酯和季铵盐改性有机蒙脱石为原料,采用原位水解法和原位脱羟法制备了TiO2/蒙脱石纳米复合物。采用X射线衍射(XRD)、拉曼光谱(Raman)表征了不同焙烧温度下TiO2/蒙脱石纳米复合物中TiO2的结构相变,并与不同焙烧温度下纯TiO2的结构相变进行对比。结果发现TiO2/蒙脱石纳米复合物中TiO2从锐钛矿相开始转变为金红石的最低温度要比纯TiO2从锐钛矿开始相转变为金红石的最低温度高200℃,且在焙烧温度1 200℃时还存在锐钛矿相,而纯TiO2在焙烧温度800℃时就全部转换为金红石相。TiO2/蒙脱石纳米复合物中TiO2和纯TiO2的平均晶粒度都随焙烧温度升高而增大,但TiO2/蒙脱石纳米复合物中TiO2的平均晶粒度要小于相同温度下焙烧纯TiO2的平均晶粒度。表明蒙脱石结构层的硅氧结构抑制了TiO2晶型由锐钛矿相向金红石相的转变,进而使相变温度升高,同时阻碍了晶体的生长。     

氧化硅对金红石相纳米TiO2微结构的影响

通过硅酸钠水解生成的无定形氧化硅对金红石相纳米TiO₂进行修饰,利用红外光谱、紫外-可见漫反射光谱、X射线衍射、透射电镜和比表面仪对纳米TiO₂进行了表征。结果表明,氧化硅沉积在纳米TiO₂的表面和颗粒之间形成一个空间网络体系,有效地抑制了TiO₂晶粒尺寸和原始粒径的长大。当热处理温度低于700 ℃时,经氧化硅处理的纳米TiO₂的晶粒尺寸、原始粒径和比表面积几乎不变;当热处理温度高于700 ℃时,经氧化硅处理的纳米TiO₂的晶粒尺寸和原始粒径开始缓慢变大,比表面积快速下降,在900 ℃下煅烧2 h,经氧化硅处理的纳米TiO₂原始粒径仍为20～40 nm。氧化硅的存在使纳米TiO₂吸收紫外线的能力增强并使其平均孔径变小。     

Visible-light responsive dye-modified TiO2 photocatalyst

A series of dye-modified TiO₂ photocatalysts were synthesized using dye Chrysoidine G (CG), tolylene-2,4-diisocyanate (TDI), and commercial TiO₂ (Degussa P25) as starting materials. TDI was used as a bridging molecule whose two -NCO groups reacted with Ti-OH of TiO₂ and -NH₂ groups of CG, respectively. As a result, special organic complexes were formed on the TiO₂ surface via stable π-conjugated chemical bonds between TiO₂ and dye molecules, confirmed by FT-IR, XPS, and UV-vis spectra. Due to the existence of π-conjugated surface organic complexes, the as-synthesized photocatalysts showed a great improvement in visible absorption (400-550 nm). Methylene blue, as a photodegradation target, was used to evaluate the photocatalytic performance, and the dye-modified TiO₂ exhibited much better activity under the visible light irradiation than bare TiO₂.     

Synthesis of titanate, TiO2 (B), and anatase TiO2 nanofibers from natural rutile sand

Titanate nanofibers were synthesized by hydrothermal method (150 °C for 72 h) using natural rutile sand as the starting materials. TiO₂ (B) and anatase TiO₂ (high crystallinity) nanofibers with the diameters of 20-100 nm and the lengths of 10-100 μm were obtained by calcined titanate nanofibers for 4 h at 400 and 700 °C (in air), respectively. The samples characterized by XRD, SEM, TEM, SAED, HRTEM, and BET surface area. This synthesis method provides a simple route to fabricate one-dimensional nanostructured TiO₂ from low cost material.     

TiO2胶粒在铝合金表面的电泳沉积及所制薄膜的光催化性能研究

TiO₂ membranes were prepared on aluminum-alloy thin plates by electrophoretic deposition and dip coating in a colloid solution of TiO₂, respectively. The photocatalytic activity of TiO₂ membrane was compared using ethylene as reactant, and the crystal and morphological structure of the membrane were characterized by XRD and SEM. The results showed that a more compact membrane with high loading of TiO₂ but lower photocatalytic activity of unit TiO₂ mass was obtained by electrophoresis compared with dip coating method. The addition of polyethylene glycol (PEG) to the sol of TiO₂ could improve the specific photocatalytic activity (ethylene conversion per unit mass TiO₂ and unit area of membrane piece) of the electrophoresis-membrane prepared from the sol, but could not change the specific photocatalytic activity of the dip-coating membrane from the sol. The ethylene conversion on the electrophoresis membrane prepared from the sol containing PEG (50 g·L^-1) was 9 times of that on the dip coating membrane. The effect of PEG on the properties of electrophoresis-membrane of TiO₂ was attributed to the change of electrokinetic properties of sol. Addition of PEG decreased ζ potential value of the sol and the mobility of the sol particle, increased viscidity of the colloid, thus decreasing both the electrophoresis deposition velocity of colloid particles and the electroosmosis velocity of diffuse layer of colloid particles. These favored the formation of a low compact and porous membrane on the electrode in electric field, and thus increasing the availability of TiO₂ in photocatalytic process.     

The solubility of Co in TiO2 anatase and rutile and its effect on the magnetic properties

Co-doped anatase and rutile bulk-samples prepared by the sol-gel technique are found to be paramagnetic at room-temperature. Only further annealing in Ar/H₂ gas results in a ferromagnetic behavior. X-ray diffraction and electron-microscope studies reveal for low doping levels <4% the formation of Co-doped rutile samples and the formation of CoTiO₃ as a new phase. Co₃O₄ can be detected in anatase samples with Co doping levels ?4%. The observed Co oxides are reduced by Ar/H₂ to Co metal. The room-temperature ferromagnetism can therefore be traced back to a segregation of metallic Co.     

TiO2纳米线的制备及其光电性能研究

利用在钛箔表面沉积一层TiO₂纳米粒子作为晶种，与NaOH反应，制备了一维物质TiO₂纳米线。并用XRD、SEM、TEM、HRTEM及EDS等分析手段对TiO₂纳米线的成分、形貌、结构进行表征。结果表明，采用该方法制得的TiO₂纳米线直径在20～50 nm左右、长度可达几微米。反应温度能显著影响所得纳米线的形貌。研究了TiO₂纳米线的光电化学性能。随反应温度的升高TiO₂纳米线光电转换效率增大。     

V2O5/TiO2催化剂表面结构FT-IR发射光谱研究(II)

用傅里哀变换红外发射光谱原位考察了V_2O_5/TiO_2催化剂在制备焙烧过程中担载偏钒酸铵的热分解步骤及其形成的表面活性相结构。偏钒酸铵在200 ℃左右分解, 在300 ℃之前完全转化为晶相V_2O_5。担载于TiO_2上的偏钒酸铵在100 ℃左右与TiO_2已产生强的化学作用, 在200 ℃之前已完全分解。对于10%(质量分数)V_2O_5/TiO_2催化剂其担载偏钒酸分解后在1020 cm~(-1)附近出现晶相V_2O_5的特征峰。但在500 ℃进一步焙烧后晶相V_5O_5的峰减弱并在1025—900 cm~(-1)区出现宽峰, 表明部分晶相V_2O_5可能转化为二维高分散的VO_x物种。2%(质量分数)V_2O_5/TiO_2催化剂在焙烧过程中也显示晶相V_2O_5的弱峰, 但同时也观察到属于VO_x物种的宽峰。进一步降低钒担载量, V_2O_5晶相特征峰逐渐消失, 而在1025—900 cm~(-1)区出现二维VO_x物种的宽峰。结果还表明傅里哀变换红外发射光谱是表征氧化物催化剂表面相结构的一种有力的方法。     

Photocatalytic activity of TiO2/SnO2/Pt prepared by the sol-gel method

This investigation compares the photodegradation performance of C.I. Reactive Red 2 (RR2) in single- and coupled-photocatalyst systems. The photocatalysts were produced via the sol-gel method. PEG and Pt addition increases the decolorization rate (1.6–2.12 h⁻¹), the amount of sulfate released and the DOC reduction percentage in coupled photocatalyst systems the cause of PEG improving the homogeneity of the final product and incorporating Pt into the lattice reduced the band gap of photocatalysts.     

The release of TiO2 and SiO2 nanoparticles from nanocomposites

There is a growing interest in the development of nanocomposites consisting of organic polymers and TiO₂ or amorphous SiO₂ nanoparticles. These nanoparticles may be released from nanocomposites. There is evidence that amorphous SiO₂ and TiO₂ nanoparticles can be hazardous. Thus, in the design of nanocomposites with such nanoparticles, hazard reduction extending to the full nanocomposite life cycle would seem a matter to consider. Options for hazard reduction include: changes of nanoparticle surface, structure or composition, better fixation of nanoparticles in nanocomposites, including persistent suppression of oxidative damage to polymers by nanoparticles, and design changes leading to the release of relatively large particles.