金刚石膜的厚度及背表面过渡层对热导率的影响

 采用微波等离子体化学气相沉积（MWPCVD）方法制备金刚石膜，研究了金刚石膜的厚度以及生长初期的SiC过渡层对其热导率的影响，给出了膜厚和背表面SiC过渡层减薄厚度与金刚石膜热导率的关系。     

金刚石薄膜的红外椭圆偏振光谱研究

采用红外椭圆偏振光谱对微波等离子体化学气相沉积法（MPCVD）和热丝化学气相沉积法（H-FCVD）制备的金刚石薄膜在红外波长范围（2.5—12.5μm）的光学参数进行了测量.建立了不同的光学模型，且在模型中采用Bruggeman有效介质近似方法综合考虑了薄膜表面和界面的椭偏效应.结果表明，MPCVD金刚石膜的椭偏数据在模型引入了厚度为77.5nm的硅表面氧化层、HFCVD金刚石膜引入879nm粗糙层之后能得到很好的拟合.最后对两种模型下金刚石薄膜的折射率和消光系数进行了计算，表明MPCVD金刚石薄膜的红外 关键词： 金刚石薄膜 红外椭圆偏振光谱 光学参数 有效介质近似     

Ce~(3+)注入掺杂金刚石薄膜蓝区电致发光研究

采用微波等离子体化学气相沉积设备在高掺杂硅衬底上沉积了一层金刚石薄膜,然后采用离子注入法在金刚石薄膜中注入不同剂量的Ce3+,从而制备出了Ce3+掺杂的金刚石薄膜.研究了其电致发光特性,得到了发光主峰位于蓝区(476 nm和435 nm处)的光发射.实验中发现随着Ce3+注入剂量的增加,电致发光强度也随之增加.     

吸收辐射复合金刚石膜的制备及光学研究

采用微波等离子体化学气相沉积（MW-PCVD）和直流热阴极辉光放电等离子体化学气相沉积（DC-PCVD）两种方法相结合,制备出一种吸收辐射的复合金刚石膜,它对宽光谱范围的光辐射具有99%—99.2%的吸收率,同时具有较低的反射率和透过率.随着黑色吸收辐射金刚石层厚度的增加,复合金刚石膜的热导率将小幅度降低,但黑色金刚石膜层厚度小于15 μm时,复合金刚石膜的热导率都在16 W·cm^-1·K^-1以上,这满足吸收辐射复合金刚石膜的高导热需求.用热阴极DC-PCVD方 关键词： 吸收辐射 光学材料 金刚石 热导率     

富勒烯作为过渡层生长金刚石薄膜研究

采用微波等离子体化学气相淀积法，以Ｃ６０膜过渡层，在光滑的单晶Ｓｉ衬底（１００）表面的研磨的石英衬底表面等光学衬底上，首次在无衬底负偏压条件下生长出多晶金刚石薄膜，通过扫描电镜观察到生长膜晶粒呈莱花状，生长表面为金刚石（１００）界面。     

微波等离子体化学气相沉积金刚石膜

微波等离子体化学气相沉积是制备金刚石膜的一个重要方法，能制备出表面光滑平整的大面积均匀金刚石膜，文章概述了ＭＰＣＶＤ制备金刚石膜的情况，介绍了ＭＰＣＶＤ制备金刚石膜装置的典型类型及其特点，在国内研制成功天线耦合石英钟罩式ＭＰＣＶＤ制备金刚石膜装置，并在硅片上沉积出大面积均匀的优质金刚石膜。     

纳米金刚石薄膜的二次电子发射特性

 简要介绍了微波等离子体化学气相沉积（MPCVD）方法在硅基底上制备纳米金刚石薄膜的过程,并对制备的薄膜进行了表面分析。在此基础上设计出了用来测定反射型二次电子发射系数的实验装置,得出了几种薄膜在不同入射能量下的发射系数,取得了二次发射系数为15的满意结果,表明纳米金刚石薄膜作为二次电子发射材料具有很好的应用前景。     

金刚石镶嵌非晶碳膜表面形貌对场致电子发射的影响

用微波等离子体化学气相沉积设备，在经过不同研磨预处理的金属钼衬底上沉积出了表面形貌有较大差异的金刚石镶嵌非晶碳膜，分别用扫描电子显微镜（ＳＥＭ）、金相显微镜和Ｘ射线衍射谱（ＸＲＤ）以及Ｒａｍａｎ光谱对样品进行了分析测试．研究了各样品的场致电子发射特性，结果发现薄膜表面由大量镶嵌有金刚石小晶粒的非晶碳球组成，在我们的实验范围内，薄膜表面非晶碳球尺寸越小，场致电子发射效果越好     

石英衬底上生长的高光学质量的纳米金刚石薄膜

采用射频等离子体增强的热丝化学气相沉积(RFHFCVD)技术在石英玻璃衬底上制备了表面光滑、晶粒致密均匀的纳米金刚石薄膜.用扫描电子显微镜(SEM)和台阶仪观测薄膜的表面形貌和粗糙度,x射线衍射(XRD)和Raman光谱表征膜层的结构,并用紫外可见近红外光谱仪测量其光透过率.实验结果表明,衬底温度、反应气压及射频功率对金刚石膜的结晶习性、表面粗糙度及光透过率均有很大程度的影响,其最佳值分别为700℃,2×133Pa和200W.在该最佳参量下经1h的生长即获得连续、平滑的纳米金刚石膜,其平均晶粒尺寸为约25 关键词： 纳米金刚石薄膜 射频等离子体增强热丝化学气相沉积 光透过率     

用甲醇－氢混合气源在不锈钢上生长金刚石薄膜的研究

利用甲醇－氢（ＣＨ３ＯＨ－Ｈ２）混合气体为气源，３０ｎｍ厚的无定形硅为过渡层，借助于微波等离子体化学气相沉积（ＭＷＣＶＤ）成功地将金刚石薄膜生长在不锈钢上，其最低生长温度可至４２０℃，并且甲醇－氢混合气体比传统的甲烷－氢（ＣＨ４－Ｈ２）更具优势，测试表明这种金刚石薄膜有希望作为耐磨层在工业上应用     

少子寿命和表面形貌与多孔硅发光性能的关系

研究了不同时间腐蚀的多孔硅的光致发光性能与多孔硅的表面形貌和少子寿命之间的关系。结果表明,多孔硅的发光来自与氧空位有关的缺陷,而多孔硅表面的氢原子能够钝化多孔硅表面的非辐射中心从而提高多孔硅的发光效率。多孔硅的空隙度随腐蚀时间的延长而增大,这也导致了多孔硅的少子寿命的降低,从而造成多孔硅的光致发光效率随多孔硅空隙度的增大以及少子寿命的降低而提高。另外,原子力显微照片表明长时间的腐蚀使多孔硅表面层被化学腐蚀,从而降低了多孔硅表面的粗糙度。     

Characterization of nanostructured CuO–porous silicon matrix formed on copper-coated silicon substrate via electrochemical etching

A pulsed anodic etching method has been utilized for nanostructuring of a copper-coated p-type (100) silicon substrate, using HF-based solution as electrolyte. Scanning electron microscopy reveals the formation of a nanostructured matrix that consists of island-like textures with nanosize grains grown onto fiber-like columnar structures separated with etch pits of grooved porous structures. Spatial micro-Raman scattering analysis indicates that the island-like texture is composed of single-phase cupric oxide (CuO) nanocrystals, while the grooved porous structure is barely related to formation of porous silicon (PS). X-ray diffraction shows that both the grown CuO nanostructures and the etched silicon layer have the same preferred (220) orientation. Chemical composition obtained by means of X-ray photoelectron spectroscopic (XPS) analysis confirms the presence of the single-phase CuO on the surface of the patterned CuO–PS matrix. As compared to PS formed on the bare silicon substrate, the room-temperature photoluminescence (PL) from the CuO–PS matrix exhibits an additional weak ‘blue’ PL band as well as a blue shift in the PL band of PS (S-band). This has been revealed from XPS analysis to be associated with the enhancement in the SiO₂ content as well as formation of the carbonyl group on the surface in the case of the CuO–PS matrix.     

多孔硅的表面碳膜钝化

报道对多孔硅（ＰＳ）进行碳膜（ＣＦ）钝化处理的结果。红外吸收光谱表明,经钝化处理样品的表面由Ｓｉ－Ｃ、Ｓｉ－Ｎ和Ｓｉ－Ｏ键所覆盖;荧光我谱表明,经钝化处理的样品较未处理的样品发光强度提高４￣４．５倍,且发光峰位明显蓝移;存放实验显示,经钝化处理的样品发光强度稳定、发光峰位不变。这些结果表明正丁胺可以在多孔硅表面形成优良的钝化碳膜,是一种十分有效的多孔硅后处理途径。     

Influence of alkali metallization (Li, Na and K) on photoluminescence properties of porous silicon

We present results for alkali metallization effects on photoluminescence (PL) properties of porous silicon (PS). The metallization of PS was realized by immersion plating in solutions containing 3 mM LiNO₃, KNO₃ and NaNO₃ metal salts. The surface bond configuration of PS was monitored by Fourier transmission infrared spectroscopy (FTIR) and it was found that the PS surface was oxidized after metallization. Surface properties of PS were investigated by field emission scanning electron microscopy (FE-SEM) and it was found that the PS surface was covered by alkali metals for short immersion times. The PL intensity increased for critical immersion times and PL spectrum shifted to high energy region with the metallization. The experimental results suggest a possibility that the metallization provides a relatively easy way to achieve an increase in the PL intensity and oxidation of the PS surface.     

White light luminescence from annealed thin ZnO deposited porous silicon

In this study, photoluminescence (PL) properties of annealed ZnO thin films deposited onto a porous silicon (PS) surface by rf-sputtering were investigated. A huge blue shift of luminescence from the ZnO deposited onto the PS surface and a broadband luminescence (white luminescence) across most of the visible spectrum were obtained after the heat treatment at 950 °C in air. The results of Fourier Transform Infrared Spectroscopy (FTIR) analysis suggested that the porous silicon surface was oxidized after ZnO deposition and the broadband luminescence was due to the conversion of Si-H bonds to Si-O-Si bonds on the PS surface. The underlying mechanisms of the broadband PL were discussed by using oxygen-bonding model for the PS and native defects model for ZnO. The experimental results suggested that the heat treatment provides a relatively easy way to achieve white luminescence from thin ZnO deposited porous silicon.     

MPCVD金刚石的Raman光谱分析

用微波等离子体化学气相淀积法（MPCVD）在Si基片上生长了金刚石薄膜，通过对其进行Raman光谱分析，一次表征了金刚石的结构，纯度及应力状况等材料性能，同时并研究了生长过程中微波功率与金刚石性质的关系。研究表明，微波等离子体化学气相溶积法生长的金刚石薄膜，除了金刚石成分的生长外，还会有部分非金刚石成分的生长，金刚石的纯度与微波功率的关系不明显，另外此种方法生长的金刚石薄膜主要表现为张应力。     

Thermal annealing dependence of some optical properties of plasma-modified porous silicon

The photoluminescence and reflectance of porous silicon (PS) with and without hydrocarbon (CH_x) deposition fabricated by plasma enhanced chemical vapour deposition (PECVD) technique have been investigated. The PS samples were then, annealed at temperatures between 200 and 800 °C. The influence of thermal annealing on optical properties of the hydrocarbon layer/porous silicon/silicon structure (CH_x/PS/Si) was studied by means of photoluminescence (PL) measurements, reflectivity and ellipsometry spectroscopy. The composition of the PS surface was monitored by transmission Fourier transform infrared (FTIR) spectroscopy. Photoluminescence and reflectance measurements were carried out before and after annealing on the carbonized samples for wavelengths between 250 and 1200 nm. A reduction of the reflectance in the ultraviolet region of the spectrum was observed for the hydrocarbon deposited polished silicon samples but an opposite behaviour was found in the case of the CH_x/PS ones. From the comparison of the photoluminescence and reflectance spectra, it was found that most of the contribution of the PL in the porous silicon came from its upper interface. The PL and reflectance spectra were found to be opposite to one another. Increasing the annealing temperature reduced the PL intensity and an increase in the ultraviolet reflectance was observed. These observations, consistent with a surface dominated emission process, suggest that the surface state of the PS is the principal determinant of the PL spectrum and the PL efficiency.     

多孔硅的微结构与发光特性研究

利用原子力显微镜（AFM）和光致荧光（PL）光谱对一系列直流腐蚀和脉冲腐蚀的多孔硅的微结构及发光特性进行了对比研究．表面和侧面的AFM结果表明，多孔硅表面呈“小山”状，有许多小的、突出的硅颗粒．在相同的腐蚀条件（等效）下，脉冲腐蚀的样品表面Si颗粒更加尖锐、突出，侧面的线状结构更明显，多孔硅层更厚．对应的PL谱，脉冲腐蚀的样品发光更强．量子限制效应的理论可以比较成功地解释这个结果 关键词：     

Long-time stabilization of porous silicon photoluminescence by surface modification

We present results on the photoluminescence (PL) properties of porous silicon (PS) as a function of time. Stabilization of PL from PS has been achieved by replacing silicon-hydrogen bonds terminating the surface with more stable silicon-carbon bonds. The composition of the PS surface was monitored by transmission Fourier transform infrared (FTIR) spectroscopy at intervals of 1 month in ageing time up to 1 year. The position of the maximum PL peak wavelength oscillates between a blue-shift and a red-shift in the 615-660 nm range with time.     

Method of porous diamond deposition on porous silicon

In this paper, we discuss the experimental results of the fabrication of porous diamond/porous silicon and porous diamond structures by chemical vapor deposition of diamond over a skeleton of porous silicon, replicating the porous surface geometry around the Si pores and also creating new porous diamond structures. Scanning electron microscopy (SEM) revealed that the diamond nuclei are deposited on the top of the porous silicon skeleton, forming isolated grains in the first nucleation stages, and then growing like the usual structure of most ceramic materials, making a self-sustained porous diamond structure. Raman spectroscopy revealed that the diamond films are of good quality, close to that of diamond films grown on crystalline silicon.