Structural, Optical and Electrical Properties of Hydrogen-Doped Amorphous GaAs Thin Films

Amorphous CaAs films are deposited on substrates of quartz glass and sificon by rf magnetron sputtering technique in different gas ambient. First, the amorphous structure of the prepared samples is identified by x-ray diffraction. Second, analysis by radial distribution function and pair correlation function method is established to characterize the microstructure of the samples. Then, the content and bond type of hydrogen are analysed using Fourier transform infrared absorption spectroscopy. It is found that the bonded hydrogen content increases with increasing partial pressure PH of H2. However, the hydrogen content saturates at PH 〉 1 × 10^-1 Pa. Hydrogen addition shills the optical absorption edge to higher energy, decreases the dark conductivity and improves the photo-sensitivity. The optical gap, dark conductivity and photo-sensitivity of the films are dependent on the bonded hydrogen content. These results demonstrate that hydrogen has obvious passivation effects on rf sputtered amorphous GaAs thin films.     

Effects of Annealing Temperature on Structural and Optical Properties of ZnO Thin Films

The effects of annealing temperature on the structural and optical properties of ZnO films grown on Si （100） substrates by sol-gel spin-coating are investigated. The structural and optical properties are characterized by x-ray diffraction, scanning electron microscopy and photoluminescence spectra. X-ray diffraction analysis shows the crystal quality of ZnO films becomes better after annealing at high temperature. The grain size increases with the temperature increasing. It is found that the tensile stress in the plane of ZnO films first increases and then decreases with the annealing temperature increasing, reaching the maximum value of 1.8 GPa at 700℃. PL spectra of ZnO films annealed at various temperatures consists of a near band edge emission around 380 nm and visible emissions due to the electronic defects, which are related to deep level emissions, such as oxide antisite （OZn）, interstitial oxygen （Oi）, interstitial zinc （Zni） and zinc vacancy （VZn^-）, which are generated during annealing process. The evolution of defects is analyzed by PL spectra based on the energy of the electronic transitions.     

磁控溅射制备铬薄膜的结构和光电学性质(英文)

用直流磁控溅射技术在石英基片上制备不同厚度(5nm～114nm之间)的铬膜.使用X射线衍射仪和分光光度计分别检测薄膜的结构和光学性质,利用德鲁特模型和薄膜的透射、反射光谱计算铬膜的厚度和光学常量,并采用Van der Pauw方法测量薄膜电学性质.结果表明:制备的铬薄膜为体心立方的多晶态,随着膜厚的增加,薄膜的结晶性能提高,晶粒尺寸增大;在可见光区域,当膜厚小于32nm时,随着膜厚的增加,折射率快速减小,消光系数快速增大,当膜厚大于32nm时,折射率和消光系数均缓慢减小并逐渐趋于稳定;薄膜电阻率随膜厚的增加为一次指数衰减.     

磁控溅射制备铬薄膜的结构和光电学性质

用直流磁控溅射技术在石英基片上制备不同厚度(5 nm~114 nm之间)的铬膜.使用X射线衍射仪和分光光度计分别检测薄膜的结构和光学性质,利用德鲁特模型和薄膜的透射、反射光谱计算铬膜的厚度和光学常量,并采用Van der Pauw方法测量薄膜电学性质.结果表明:制备的铬薄膜为体心立方的多晶态,随着膜厚的增加,薄膜的结晶性能提高,晶粒尺寸增大;在可见光区域,当膜厚小于32 nm时,随着膜厚的增加,折射率快速减小,消光系数快速增大,当膜厚大于32 nm时,折射率和消光系数均缓慢减小并逐渐趋于稳定;薄膜电阻率随膜厚的增加为一次指数衰减.     

ZnO薄膜的光学性质研究

采用直流反应磁控溅射方法在玻璃基底上成功地淀积ｃ轴取向性好的ＺｎＯ薄膜。经过优化计算，获得并分析了不同氧分压下制备的ＺｎＯ薄膜的折射率ｎ和消光系数ｋ的数值；同时得到了吸收光学带隙Ｅｏｐｔ，用能带模型解释了Ｅｏｐｔ的变化规律。     

Electronic and Optical Properties of GaAlAs/GaAs Thin Films

Technical Physics - It has been shown that the formation of GaAlAs nanofilms on a GaAs surface leads to an increase in the emission coefficient of true secondary electrons and in the quantum yield...     

N掺杂对非晶C薄膜的电子结构与光学性质的影响

用直流磁控溅射法制备了非晶C薄膜及N掺杂非晶C(a-C∶N)薄膜,用紫外-可见分光光谱仪、椭圆偏振仪、俄歇电子能谱(AES)等对薄膜进行了检测。结果表明：随源气体中N气含量的增加,透过率和折射率变小, 而光学带隙先增大后减小; 当薄膜中N的含量很少,N的掺入对sp3杂化C起稳定作用,使得薄膜光学带隙E_g增大。而较高量N的掺入抑制了sp3杂化C的形成,提高了薄膜中sp2键含量,使得薄膜光学带隙变小。参数D定义为俄歇电子能谱(AES)中最大正峰和最低负峰之间的距离,用俄歇电子能谱中的D值来计算薄膜的sp2键的百分含量,俄歇电子能谱(AES)表征也表明：较高量的N的掺入抑制了sp3杂化C的形成。所以应该考虑在较低N分压条件下掺N来改善非晶C薄膜的光学性能。     

对基于磁控溅射方法沉积的HfO2薄膜的紫外光学特性及薄膜结构的研究

本文基于磁控溅射方法,功率从160 W增加到240 W,在石英衬底上沉积氧化铪薄膜(HfO₂),并对沉积后的薄膜进行退火处理. 利用X射线衍射谱、X射线光电子能谱、紫外-可见-近红外透射谱和椭圆偏振仪对HfO₂薄膜进行研究,对比了退火前后HfO₂薄膜的光学特性及薄膜结构的变化. 实验结果显示,HfO₂薄膜对波长大于200 nm的入射光具有很低的吸收系数. 优化退火温度和时间,可以将沉积后的HfO₂薄膜从非晶态转化成多晶态. 退火有助于结晶生成和内应力的增加,同时退火可以优化薄膜的化学计量比,提升薄膜的光学密度及折射率. 对功率在220 W左右沉积的薄膜进行退火,获得的HfO₂薄膜具有较高并且稳定的光学折射率(>2)和紫外光透射率,可在紫外波段减反膜系统中得到应用.     

Cu掺杂ZnO薄膜的光学性质

采用射频反应磁控溅射方法,在Si(100)和石英基片上使用双靶溅射的方法制备了Cu掺杂ZnO薄膜。利用X射线衍射、透射光谱和光致发光光谱分析了薄膜的晶体结构及光学性质,并与密度泛函理论计算的结果进行了对比。研究结果显示:Cu掺杂ZnO薄膜均具有高的c轴择优取向,无Cu及其氧化物相关相析出,掺杂对晶格参数的影响较小,与理论计算结果一致。Cu掺杂显著改变了ZnO薄膜在近紫外及可见光波段的吸收特性,其光学带隙随着Cu掺杂量的增加有所减小,带隙宽度的变化趋势与理论结果有着很好的一致性。Cu掺杂显著降低了ZnO薄膜的发光效率,具有明显的发光猝灭作用,但并不影响光致发光的发光峰位。说明Cu掺杂导致的吸收特性的改变可能与杂质能级有关,这与能带结构计算发现的Cu-3d电子态位于价带顶附近的禁带中是一致的。     

ZnO薄膜的制备和结构特性及应变

在SiO₂/Si衬底上面,利用射频磁控溅射方法,在不同的工艺条件下生长ZnO薄膜,然后进行热处理(600～1000℃退火).研究了氩氧比和退火温度对薄膜结晶性能的影响.薄膜的表面结构和晶体特性通过扫描电子显微镜(SEM)、X射线衍射(XRD)来进行表征.结果表明:所制备的薄膜为多晶纤锌矿结构,具有垂直于衬底的c轴(002)方向的择优取向性.热处理可使ZnO(002)衍射峰相对强度增强,半峰全宽(FWHM)变小,即退火使c轴生长的薄膜取向性增强.未经退火的ZnO薄膜存在张应力,经过热处理后应力发生改变,最后变成压应力,并且随着退火温度的升高,压应力逐渐增大.     

射频磁控溅射ZnO薄膜的结构和光学特性

采用射频（RF）反应磁控溅射法在n-Si(001)衬底上外延生长ZnO薄膜。XRD谱测量显示出较强的（002）衍射峰，表明ZnO薄膜为c轴择优取向生长的。室温PL谱测量观察到了较强的紫外光发射和深能级发射。     

Optical and Structural Properties of Ammonia-Free Amorphous Silicon Nitride Thin Films for Photovoltaic Applications

Hydrogenated amorphous silicon nitride (a-SiN_x:H) thin films have been deposited through the green chemistry route using silane (SiH₄) and nitrogen (N₂) as process gases with SiH₄ flow being variable and N₂ flow being constant without the use of pollutant and corrosive ammonia (NH₃) by the plasma-enhanced chemical vapor deposition technique at 13.56 MHz. Fourier transform infrared spectroscopy analysis shows various possible vibrational modes of Si-H, Si-N, and N-H bonds present in the film. Raman spectroscopy is performed on these samples to calculate volume fractions corresponding to amorphous phases present in the a-SiN_x:H films. The refractive index (η) values are calculated using Swanepoel's method, which are in the range of 2.89 to 3.17. The thickness of the deposited films has been evaluated using transmission spectra. Absorption coefficient and band gap (E _g) values are obtained from optical absorption studies. An increase in the E _g and a decrease in the η value have been observed for the samples grown with decreasing SiH₄ flow.     

溶胶-凝胶法制备MgxZn1-xO薄膜的结构及光学特性

用溶胶-凝胶法制备了一系列的Mg_xZn_1-xO(0≤x≤0.3)薄膜,并用X射线衍射(XRD)和光致发光(PL)研究了不同的退火温度和Mg的掺杂含量对Mg_xZn_1-xO薄膜的结构和光学性质的影响.研究表明:Mg_xZn_1-xO薄膜为单相六角纤锌矿结构,并且具有沿c轴的择优取向;发现了中间热处理温度为350℃的Mg_xZn_1-xO薄膜退火温度的转折点为700℃,低于这个温度时随退火温度的升高,(002)衍射峰强度增强且掺Mg的薄膜既有紫外光又有绿光发射;800℃退火时,薄膜的(002)衍射峰强度减小,出现了(100)和(101)衍射峰,且掺Mg的薄膜只有紫外发光峰.不同的掺杂浓度对于发光也有影响,低于700℃退火时,ZnO薄膜只出现紫外发光峰,掺Mg的薄膜却出现了紫外和绿光两个发光峰.     

Annealing Effects on the Structural and Optical Properties of Thermally Deposited Tin Antimony Sulfide Thin Films

We report the deposition and characterization of tin antimony sulfide thin films on a soda glass substrate by a thermal evaporation technique. The thin films were annealed in argon gas at 150, 175, and 300 °C inside glass ampoules. The structural and optical properties of the deposited and annealed films are investigated. X-ray diffraction (XRD) patterns show that the films are polycrystalline in structure. Photoconductivity plot revealed good response in the NIR and visible regions, while the films show no transmittance below 700 nm. The absorption coefficient was of the order of 10⁶ cm^?1. Optical band gaps were also evaluated and a decrease in band gap was observed due to annealing. Hot point probe technique was employed for type of conductivity.     

杂质银对氧化锌薄膜气敏光学特性的影响

用反应式射频磁控溅射方法制备了纯氧化锌（ＺｎＯ）薄膜和掺Ａｇ的ＺｎＯ气敏光学传感薄膜。测量了这些薄膜在ＮＯｘ气体中的透射光谱，然后由透射光谱获得了灵敏度的变化规律，发现掺Ａｇ后的ＺｎＯ薄膜对ＮＯｘ气体的灵敏度高于纯ＺｎＯ薄膜，用俄歇电子能谱（ＡＥＳ）测试了这些薄膜的组分，发现当掺Ａｇ量为５％时灵敏度最高，并结合朗缪尔（Ｌａｎｇｍｕｉｒ）型吸附平衡关系式解释了这些现象，理论和实验结果能很好的相符。     

Y2O3稳定ZrO2薄膜的结构和光学特性

用电子束蒸发法制备出四种不同Y2O3含量的Y2O3稳定ZrO2（YSZ）薄膜,用X射线衍射和透射光谱测定薄膜的结构和光学性能.结果表明：随着Y2O3含量的增加,ZrO2薄膜从单斜相向高温相（四方相和立方相）转变,获得了结构稳定的YSZ薄膜;YSZ薄膜的晶粒尺寸都比ZrO2薄膜的大,但随着Y2O3加入量的增加,晶粒尺寸有减小的趋势,薄膜表面也趋向光滑平整.所有YSZ薄膜的透射谱线都与ZrO2薄膜相似,在可见光和红外光区都有较高的透过率.Y2O3的加入还可以改变薄膜的折射率,在一定范围内可得到所需的任意折射率.     

Optical and Photoelectric Properties of GaS Thin Films and GaS/InSe Heterostructure

Optics and Spectroscopy - GaS thin films have been grown by the SILAR method, their structures have been analyzed, and their optical and photoelectric properties have been investigated. The...     

退火对ZnO薄膜光学特性的影响

用射频磁控溅射法在蓝宝石衬底上制备出ZnO薄膜,通过X射线衍射(XRD)、扫描电镜(SEM)和光致发光(PL)谱等研究了退火温度对ZnO薄膜结构和光学性质的影响。测量结果显示,所制备的ZnO薄膜为六角纤锌矿结构,具有沿c轴的择优取向;随着退火温度的升高,(002)XRD峰强度和平均晶粒尺寸增大,(002)XRD峰半高宽(FWHM)减小,光致发光紫外峰强度增强。结果证明,用射频磁控溅射法通过适当控制退火温度可得到高质量ZnO薄膜。     

Co掺杂ZnO薄膜的结构和磁学性能

研究了用单束脉冲激光沉积法制备的Co掺杂ZnO薄膜的结构和磁学性能。XRD表征结果表明制备的薄膜是具有沿c轴择优取向的纤锌矿点阵结构。然而,进一步的高分辨电子显微镜结果显示整个样品上的晶体取向并不完全相同。很难说明形成了单晶。结果分析表明Co占据了部分Zn的格点,并对电子结构产生了影响。室温下观察到了磁滞回线,显示掺杂Co可以实现ZnO的磁性翻转,但磁性比较小。该薄膜与我们以前用双束脉冲激光沉积法制备的Co掺杂ZnO薄膜具有相似的性能,提示我们其内部的机制可能相似。     

Effect of the Structural Properties on the Electrical Resistivity of the Al/Ag Thin Films during the Solid-State Reaction

Physics of the Solid State - Based on the results of in situ electron diffraction study of the solid-state reaction and electrical resistivity measurements on the Al/Ag thin films with an atomic...