Electro-optical characteristics for the photoaligned vertical alignment cell using photopolymer surfaces containing chalconyl and cholesterly groups

A new photoalignment material, copoly(4-methacryloyloxychalcone-cholesteryl methacrylate) (copoly(M4Ch-ChMA)), was synthesized and the electro-optical characteristics for the photoaligned vertically aligned (VA) liquid crystal display (LCD) were studied. Excellent voltagetransmittance characteristics were achieved for the photoaligned VA-LCD with 1 min polarized UV exposure at an oblique direction of 30° on the copoly(M4Ch-ChMA) surfaces. The response time of the VA-LCD was about 39 ms, and increased with increasing UV exposure time. We suggest that the proportion of photodimerized chalcone group increased with increasing UV exposure time, contributing to a higher response time.     

Electro-optical characteristics of photo-aligned vertical-alignment cells on photo-crosslinkable copolymer surfaces containing the cholesteryl moiety

The electro-optical (EO) performances of a photoaligned vertical-alignment liquid crystal display (VA-LCD) on a copoly(4-methacryloyloxychalcone-cholesteryl methacrylate) surface for homeotropic LC alignment were studied. Good thermal stability of the synthesized photo-crosslinkable copolymer was seen during thermogravimetric analysis. A good voltage-transmittance curve and fast response time achieved in the photoaligned VA-LCD with obliquely polarized UV exposure at 30° from the vertical on the photo-crosslinkable copolymer surfaces. The EO characteristics of the photoaligned VA-LCD decreased after long time UV exposure because of dissociation of the ester linkage in the chalcone structure of the photo-crosslinkable polymer.     

Electro-optical characteristics of photo-aligned vertical-alignment cells on photo-crosslinkable copolymer surfaces containing the cholesteryl moiety

The electro-optical (EO) performances of a photoaligned vertical-alignment liquid crystal display (VA-LCD) on a copoly(4-methacryloyloxychalcone-cholesteryl methacrylate) surface for homeotropic LC alignment were studied. Good thermal stability of the synthesized photo-crosslinkable copolymer was seen during thermogravimetric analysis. A good voltage-transmittance curve and fast response time achieved in the photoaligned VA-LCD with obliquely polarized UV exposure at 30° from the vertical on the photo-crosslinkable copolymer surfaces. The EO characteristics of the photoaligned VA-LCD decreased after long time UV exposure because of dissociation of the ester linkage in the chalcone structure of the photo-crosslinkable polymer.     

Synthesis of novel aromatic polyimides containing bulky side chain for vertical alignment liquid crystals

In this study, a novel 4-（4-octyloxybenzoyloxy）biphenyl-3′,5′-diaminobenzoate and polyimides based on it were synthesized. The polyimide with mesogenic unit side chain exhibited excellent vertical alignment for nematic liquid crystal （LC）. The pretilt angles of LCs above 89° were kept after the rubbing process with 220 mm rubbing strength. The polyimide films as the alignment layer were baked at 120℃ for 12 h, the vertical alignment of LCs was still uniform and stable. Meanwhile, the UV-vis spectra of the noyel polyimide films showed the high transparency in a visible wave length.     

Synthesis and characteristics of novel chelate fiber containing amine and amidine groups

A polyacrylonitrile (PAN) fiber was adopted for the backbone of a chelate polymer and poly(acrylo‐amidino ethylene amine) (PAEA) was prepared through a one‐step reaction between the PAN fiber and ethylenediamine (EDA). The maximum removal capacity and degree of substitution were 7.8 meq per gram of dried PAEA and 98%, respectively. The PAEA was tested as an adsorbent in single and two‐component metal aqueous solutions under changing pH. The Cu²⁺ ion accomplished maximum adsorption amount at pH 3 and the order of maximum adsorbed amounts on PAEA is Cu²⁺ > Ag⁺ > Zn²⁺ > Ni²⁺ > Pb²⁺ in molar basis. FT‐IR spectroscopy was employed to characterize the chemical bonding in metal aqueous solutions and surface morphology was examined using atomic force microscopy (AFM) and scanning electron microscopy (SEM). Copyright © 2004 John Wiley & Sons, Ltd.     

Elucidation of functional groups on gram-positive and gram-negative bacterial surfaces using infrared spectroscopy

Surface functional group chemistry of intact Gram-positive and Gram-negative bacterial cells and their isolated cell walls was examined as a function of pH, growth phase, and growth media (for intact cells only) using attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy. Infrared spectra of aqueous model organic molecules, representatives of the common functional groups found in bacterial cell walls (i.e., hydroxyl, carboxyl, phosphoryl, and amide groups), were also examined in order to assist the interpretation of the infrared spectra of bacterial samples. The surface sensitivity of the ATR-FTIR spectroscopic technique was evaluated using diatom cells, which possess a several-nanometers-thick layer of glycoprotein on their silica shells. The ATR-FTIR spectra of bacterial surfaces exhibit carboxyl, amide, phosphate, and carbohydrate related features, and these are identical for both Gram-positive and Gram-negative cells. These results provide direct evidence to the previously held conviction that the negative charge of bacterial surfaces is derived from the deprotonation of both carboxylates and phosphates. Variation in solution pH has only a minor effect on the secondary structure of the cell wall proteins. The cell surface functional group chemistry is altered neither by the growth phase nor by the growth medium of bacteria. This study reveals the universality of the functional group chemistry of bacterial cell surfaces.     

Sulfonated poly(fluorenyl ether) membranes containing perfluorocyclobutane groups for fuel cell applications

This paper describes the preparation and electrochemical properties of new proton conducting polymer membranes, sulfonated poly(fluorenyl ether) membrane-containing perfluorocyclobutane (PFCB) moieties for fuel cell applications. The sulfonated polymers were prepared via thermal cyclodimerization of 9,9-bis(4-trifluorovinyloxyphenyl)fluorene and subsequent post-sulfonation using chlorosulfonic acid (CSA) as a sulfonating agent. The post-sulfonation reaction was carried out by changing the molar ratio of CSA/repeating unit of the polymer at room temperature for 5 h and the resulting sulfonated polymers showed different degrees of sulfonation (DS) and ion exchange capacities (IEC). With the increment of CSA content, the DS, IEC and water uptake of the sulfonated polymer membranes increased. Their proton conductivity was investigated as a function of temperature. The polymer membrane with an IEC value of 1.86 mmol/g showed a water content of 25% similar to Nafion-115's but showed higher proton conductivity than Nafion-115 over the temperature 25–80 °C. The polymer membrane with lower water uptake and higher IEC showed similar proton conductivity and methanol permeability to Nafion-115. These results confirmed that the sulfonated poly(fluorenyl ether)-containing PFCB groups could be a promising material for fuel cell membranes.     

Novel alignment method for control of high pretilt angle by using a solvent dipping effect on polymer surfaces

A novel alignment method for control of high pretilt angle in nematic liquid crystals (NLC), using a solvent dipping effect on various alignment layers, was successfully investigated. The pretilt angle of a NLC is increased by dipping before rubbing treatment on three kinds of rubbed polyimide (PI) surfaces. The pretilt generated by the dipping after rubbing a PI surface with a short side chain is high compared with a PI surface with a long side chain. The pretilt generated by dipping before rubbing homeotropic layer of a positive type NLC (δε > 0) is lower than that of the negative type NLC (δε < 0). The generated NLC pretilt angle is attributed to the perpendicular component of the permittivity epsilon of the NLC.     

Three-component photopolymers based on thermal crosslinking and acidolytic de-crosslinking of vinyl ether groups. 2. effects of acid components on photopolymer characteristics

The three-component photopolymers consisting of poly(p-hydroxystyrene) (PHS) or poly(styrene-co-acrylic acid) (PSA) as the binder polymer, 2,2-bis(4-(2-(vinyloxy)ethoxy)phenyl)propane (BPA-DEVE) or 1,1,1-tris(4-(2-(vinyloxy)ethoxy)phenyl)ethane (THPETEVE) as the crosslinking agent, and a photoacid generator were investigated with regard to their lithographic characteristics and thermal crosslinking reactivity because of the acidity of the acid component. The thermal crosslinking rate can be represented as the pseudo first-order reaction. The PSA copolymer with an acrylic acid unit has the higher crosslinking rate and sensitivity, and the lower activation energy. Under low baking temperatures at which crosslinking does not take place, dual-mode resist behavior is observed.     

Sulfonated poly(arylene ether sulfone) ionomers containing fluorenyl groups for fuel cell applications

A series of sulfonated poly(arylene ether sulfone)s (SPEs) containing fluorenyl groups as bulky components were synthesized and characterized for fuel cell applications. Introduction of disodium 3,3′-disulfo-4,4′-difluorophenyl sulfone (SFPS) monomer gave ionomers with high acidity and accordingly high proton conductivity as well as high proton diffusion coefficient (D_σ) at low humidity. The membrane of SPE60 (where the number denotes mole percentage of the component containing sulfonic acid groups; IEC (ion exchange capacity) = 1.68 mequiv./g) exhibited high proton conductivity of 4.6 × 10⁻³ S/cm at 40% RH and 80 °C, which is one order of magnitude higher than that (6 × 10⁻⁴ S/cm) of our previous SPE (SPE-1, IEC = 1.58 mequiv./g). D_σ of SPE60 membrane was ca. 4 times higher than that of the SPE-1 membrane at low water volume fraction. SPE membranes showed good oxidative and hydrolytic stability as well as favorable thermal and mechanical properties. Small-angle X-ray scattering analyses showed that the phase separation of SPE membranes was much less developed than that of the perfluorinated Nafion membrane which accounts for lower hydrogen and oxygen permeability of the former membranes.     

Synthesis and characterization of novel polyimides containing stilbene unit in the side chain and their controllability of nematic liquid crystal alignment on the rubbed surfaces

Four polyimides containing hexylene spacer and a fluorostilbene unit in the side chains were prepared in thin‐film form by two‐step condensation of 3,3′‐bis[(4′‐fluoro‐4‐stilbenyl)oxyhexyloxy]‐4,4′‐biphenyldiamine (FS6B) with pyromellitic dianhydride (PMDA), benzophenone‐3,3′,4,4′‐tetracarboxylic dianydride (BTDA), 4,4′‐oxydi(phthalic anhydride) (ODPA), and 4,4′‐hexafluoroisopropylidenedi(phthalic anhydride) (6FDA), respectively, and their controllability of liquid crystal (LC) alignment on rubbed surfaces was investigated. Pretilt angles of LCs were achieved in the 2–9° range, depending on the rubbing density and backbone structures. The effect of the mesogenic stilbene group on the pretilting of LCs was distinctive in FS6B‐PMDA. Contact‐angle measurements on thin films annealed at 120 °C revealed that FS6B‐PMDA potentially had the better alignment stability than FS6B‐6FDA. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3622–3632, 2001     

UV-induced vertical alignment liquid crystal cell with two species of monomers having vertical-alignment-induced side-chain group and phenanthrene group

We propose the method for formation of the vertical alignment polymer film by polymerisation of the monomers being dissolved in the liquid crystal (LC) material. For obtaining the vertical alignment, combination of the two monomers, 4-(4?-octyloxy-biphenyl-4-yloxy)-butyl ester (AOBBE) and 2,7-dimethacryloyl-oxy-phenanthrene (DMAPhen), was found to be useful.

The monomer DMAPhen initiates the polymerisation under UV light exposure, and the AOBBE unit induces the vertical alignment without generating any alignment defects. The monomer DMAPhen is useful for maintaining the high voltage holding ratio and low residual direct current voltage after UV light exposure because the molecules of DMAPhen do not remain in the LC layer.     

Water‐dispersible microgel modified with methacryloyl groups by ionic bonding on the surface and the photopolymer microgel

A novel water‐dispersible reactive microgel, which had a diameter of 40–90 nm, was synthesized for photopolymer materials. The microgels have segments with substituted ammonium groups, to provide water solubility, in their polymer networked structure. It has unsaturated groups connected to the quaternary nitrogens by ionic bonding (I‐type microgel). The I‐type microgel was compared with one that has methacryloyl groups connected with the quaternary nitrogens of the microgel by covalent bonding (C‐type microgel). The I‐type microgels were able to separately control the modified amount of quaternary nitrogen and methacryloyl group. In the presence of 2,4‐diethylthioxantone as a photoinitiator and pentaerthritol triacrylate as a crosslinker, the photopolymer containing the C‐type or I‐type microgels had sensitivity high enough for practical use. Not only the amount of the methacryloyl group of the microgel but the amount of the quaternary nitrogen affected the sensitivity and the rate of polymerization of the water‐dispersible photopolymer containing the I‐type microgels. Copyright © 2000 John Wiley & Sons, Ltd.     

Sulfonated poly(fluorene-co-sulfone)ether membranes containing perfluorocyclobutane groups for fuel cell applications

A new class of sulfonated poly(fluorene-co-sulfone)ether membranes containing perfluorocyclobutane (PFCB) groups were synthesized and characterized in terms of their electrochemical properties as proton exchange membranes for fuel cells. Two monomers, 9,9-bis(4-trifluorovinyloxyphenyl)fluorene and 4,4′-sulfonyl-bis(trifluorovinyloxy)biphenyl were synthesized and statistically copolymerized by thermal [2π + 2π] cycloaddition to yield a series of polymers containing 0–60 mol% of fluorenyl content (PFS-X). The copolymers were then sulfonated using chlorosulfonic acid to afford five kinds of ionomers with different sulfonation levels (SPFS-X), which were cast into membranes and analyzed in terms of electrochemical properties. It was found that the ion exchange capacity (IEC), water uptake, proton conductivity and methanol permeability values of SPFS-X increased with the increment of the sulfonated fluorenyl content. The proton conductivities of SPFS-50 and -60 with high IECs and water uptake values were higher than those of Nafion-115 between 25 and 80 °C. The methanol permeability of SPFS-X was considerably lower than that of Nafion-115.     

Synthesis of Fe@C nanoparticles containing sulfo groups on their surfaces and study of their aggregation behavior in aqueous media

Russian Chemical Bulletin - Magnetic iron nanoparticles (MNPs) encapsulated in a carbon shells and containing sulfo groups on the surface (Fe@C-SO3H) were synthesized. The aggregative stability of...     

Synthesis and properties of multiblock copoly(arylene ether)s containing superacid groups for fuel cell membranes

A series of block copoly(arylene ether)s containing pendant superacid groups were synthesized, and their properties were investigated for fuel cell applications. Two series of telechelic oligomers, iodo‐substituted oligo(arylene ether ketone)s and oligo(arylene ether sulfone)s, were synthesized. The degree of oligomerization and the end groups were controlled by changing the feed ratio of the monomers. The nucleophilic substitution polymerization of the two oligomers provided iodo‐substituted precursor block copolymers. The iodo groups were converted to perfluorosulfonic acid groups via the Ullmann coupling reaction. The high degree of perfluorosulfonation (up to 83%) was achieved by optimizing the reaction conditions. Tough and bendable membranes were prepared by solution casting. The ionomer membranes exhibited characteristic hydrophilic/hydrophobic phase separation with large hydrophilic clusters (ca. 10 nm), which were different from that of our previous random copolymers with similar molecular structure. The block copolymer structure was found to be effective in improving the proton‐conducting behavior of the superacid‐modified poly(arylene ether) ionomer membranes without increasing the ion exchange capacity (IEC). The highest proton conductivity was 0.13 S/cm at 80 °C, 90% relative humidity, for the block copolymer ionomer membrane with IEC = 1.29 mequiv/g. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Preparation of triazamacrocycles containing only secondary amine functions using both tosyl and boc protecting groups

1,8,15-Triazacycloheneicosane ( 1 ); 1,9,17-triazacyclotetracosane ( 2 ) and 1,10,19-triazacycloheptacosane ( 3 ) were prepared by treating the appropriate N,N-bis(ω-bromoalkyl)toluenesulfonamide 8–10 with the appropriate N,N′-ditosyl-α,ω-diaminoalkane 11–13 in dimethylformamide using sodium hydride as the base followed by phenol and 33% hydrobromic acid in acetic acid to remove the tosyl protecting groups. 2-Allyloxymethyl-4,11,18- triazaoxacycloheneicosane ( 4 ) was prepared in two ways. First, N,N′,N″-tritosylbis(hexamemylene)triamine ( 18 ) was treated with 2-allyloxymethyl-3-oxa-1,6-hexanediol ditosylate ( 23 ) and cesium carbonate in dimethylformamide followed by sodium amalgam to remove the tosyl protecting groups. The second preparation of 4 was done by treating the tri-BOC analog of 18 with 23 followed by hydrochloric acid in isopropyl alcohol to remove the BOC protecting groups. The overall yields of 4 using these two processes were very close.     

Selective colorimetric assay of cyanide ions using a thioamide-based probe containing phenol and pyridyl groups

The selective assay of cyanide ions with a thioamide compound (HNPTU) containing phenol and pyridine as a chemosensor is reported using absorbance changes in a buffered aqueous solution (50 mM HEPES, pH 7.4) containing ethanol. Upon treatment with cyanide ions, the colorless solution of HNPTU turned yellow. No significant changes were observed with other comparable anions, such as F⁻, Cl⁻, Br⁻, I⁻, and CH₃COO⁻. The color change of HNPTU upon treatment with CN⁻ was maintained even in the presence of the comparable monovalent anions. The complex stability constant (K_a = 2.6 × 10³) for the stoichiometric 1:1 complexation of HNPTU with cyanide ions was obtained based on absorbance titrations. The interaction of HNPTU with cyanide ions was proposed to be deprotonation, as shown by NMR and Cu(II) treatment experiments.     

Photolabile micropatterned surfaces for cell capture and release

A method for capture and release of cells was developed using a photolabile linker and antibody-attached glass surface with a poly(ethylene glycol) (PEG)-pattern.