Multilayers of weak polyelectrolytes of low and high molecular mass assembled on polypropylene and self-assembled hydrophobic surfaces

Hydrophobic self-assembled octadecyltrichlorosilane (ODTS), ultrathin films of polypropylene, and ODTS modified with cationic dioctadecyldimethylammonium bromide are employed as substrates for deposition of multilayers of poly(allylamine hydrochloride) and poly(acrylic acid) from aqueous solution. The assembly of highly dissipative polyelectrolyte multilayers (PEMs) is demonstrated by quartz crystal microgravimetry. The initial rate of adsorption is faster and the adsorbed amount larger on the cationic surface, while the detailed structure of the PEMs, as determined by atomic force microscopy imaging, is related primarily to the molecular weight of the adsorbing polymers. A more extensive PEM adsorption on the hydrophobic surfaces takes place with increasing ionic strength of the background electrolyte solution. The water contact angle depends on the type of polymer adsorbed as the outermost layer, indicating that, despite the expected interdiffusion for the different polymer chains, there is a net macromolecular segregation to the free surface. Surface modification with the high molecular weight PEMs produces a more marked reduction of the hydrophilicity of the substrate.     

Unusual collapse of highly hydrated polyelectrolyte multilayers with the ionic strength

Highly hydrated polyelectrolyte multilayers (PEMs) were fabricated by “layer by layer” (LBL) assembly of poly (diallyl dimethyl ammonium chloride) (PDADMAC) and poly (sodium 4‐styrene sulfonate) (PSS) in 0.5 M NaCl. Both thickness and hydration of the film were determined in situ as the multilayer was assembled by means of the quartz crystal microbalance with dissipation (QCM‐D) and the Spectroscopic Ellipsometry techniques combined in a single device. For PEMs of 17 total layers in water, a final thickness of up to 300 nm and a hydration of 69% were measured. The response towards the ionic strength was then studied by means of QCM‐D. PEMs of 17 layers, with PDADMAC as last layer, shrunk dramatically and lost water when exposed to aqueous NaCl solutions of increasing concentration. Indeed, a thickness variation up to 100 nm and reduction in the 50% of the water content were observed when the PEM was exposed to 1 M NaCl. On the contrary, PEMs where PSS appears on top showed no measurable change upon the variation in the ionic strength. This brings the possibility to control the responsive character of the PEMs simply by selecting the last polyelectrolyte layer (PDADMAC or PSS) deposited. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Micropatterning neuronal cells on polyelectrolyte multilayers

This paper describes an approach to adhere retinal cells on micropatterned polyelectrolyte multilayer (PEM) lines adsorbed on poly(dimethylsiloxane) (PDMS) surfaces using microfluidic networks. PEMs were patterned on flat, oxidized PDMS surfaces by sequentially flowing polyions through a microchannel network that was placed in contact with the PDMS surface. Polyethyleneimine (PEI) and poly(allylamine hydrochloride) (PAH) were the polyions used as the top layer cellular adhesion material. The microfluidic network was lifted off after the patterning was completed and retinal cells were seeded on the PEM/PDMS surfaces. The traditional practice of using blocking agents to prevent the adhesion of cells on unpatterned areas was avoided by allowing the PDMS surface to return to its uncharged state after the patterning was completed. The adhesion of rat retinal cells on the patterned PEMs was observed 5 h after seeding. Cell viability and morphology on the patterned PEMs were assayed. These materials proved to be nontoxic to the cells used in this study regardless of the number of stacked PEM layers. Phalloidin staining of the cytoskeleton revealed no apparent morphological differences in retinal cells compared with those plated on polystyrene or the larger regions of PEI and PAH; however, cells were relatively more elongated when cultured on the PEM lines. Cell-to-cell communication between cells on adjacent PEM lines was observed as interconnecting tubes containing actin that were a few hundred nanometers in diameter and up to 55 microm in length. This approach provides a simple, fast, and inexpensive method of patterning cells onto micrometer-scale features.     

Ion‐Specific Oil Repellency of Polyelectrolyte Multilayers in Water: Molecular Insights into the Hydrophilicity of Charged Surfaces

Surface wetting on polyelectrolyte multilayers (PEMs), prepared by alternating deposition of polydiallyldimethylammonium chloride (PDDA) and poly(styrene sulfonate) (PSS), was investigated mainly in water‐solid‐oil systems. The surface‐wetting behavior of as‐prepared PEMs was well correlated to the molecular structures of the uncompensated ionic groups on the PEMs as revealed by sum frequency generation vibrational and X‐ray photoelectron spectroscopies. The orientation change of the benzenesulfonate groups on the PSS‐capped surfaces causes poor water wetting in oil or air and negligible oil wetting in water, while the orientation change of the quaternized pyrrolidine rings on the PDDA‐capped surfaces hardly affects their wetting behavior. The underwater oil repellency of PSS‐capped PEMs was successfully harnessed to manufacture highly efficient filters for oil‐water separation at high flux.     

Tunable resistive m-dPEG acid patterns on polyelectrolyte multilayers at physiological conditions: template for directed deposition of biomacromolecules

This paper describes a new class of salt-responsive poly(ethylene glycol) (PEG) self-assembled monolayers (SAMs) on top of polyelectrolyte multilayer (PEMs) films. PEM surfaces with poly(diallyldimethylammonium chloride) as the topmost layer are chemically patterned by microcontact printing (muCP) oligomeric PEG molecules with an activated carboxylic acid terminal group (m-dPEG acid). The resistive m-d-poly(ethylene glycol) (m-dPEG) acid molecules on the PEMs films were subsequently removed from the PEM surface with salt treatment, thus converting the nonadhesive surfaces into adhesive surfaces. The resistive PEG patterns facilitate the directed deposition of various macromolecules such as polymers, dyes, colloidal particles, proteins, liposomes, and nucleic acids. Further, these PEG patterns act as a universal resist for different types of cells (e.g., primary cells, cell lines), thus permitting more flexibility in attaching a wide variety of cells to material surfaces. The patterned films were characterized by optical microscopy and atomic force microscopy (AFM). The PEG patterns were removed from the PEM surface at certain salt conditions without affecting the PEM films underneath the SAMs. Removal of the PEG SAMs and the stability of the PEM films underneath it were characterized with ellipsometry and optical microscopy. Such salt- and pH-responsive surfaces could lead to significant advances in the fields of tissue engineering, targeted drug delivery, materials science, and biology.     

Tunable Engineered Extracellular Matrix Materials: Polyelectrolyte Multilayers Promote Improved Neural Cell Growth and Survival

Poly‐d ‐lysine (PDL) and poly‐l ‐lysine are standard surfaces for culturing neural cells; however, both are relatively unstable, costly, and the coated surface typically must be prepared immediately before use. Here, polyelectrolyte multilayers (PEMs) are employed as highly stable, relatively inexpensive, alternative substrates to support primary neural cell culture. Initial findings identify specific silk‐based PEMs that significantly outperform the capacity of PDL to promote neuronal survival and process extension. Based on these results, a library of PEM variants, including commercial and bio‐sourced polyelectrolytes, is generated and three silk‐based PEMs that substantially outperform PDL as a substrate for primary neurons in cell culture are identified. Further, testing these PEM variants as substrates for primary oligodendrocyte progenitors demonstrates that one silk‐based PEM functions significantly better than PDL. These findings reveal specificity of cellular responses, indicating that PEMs may be tuned to optimally support different neural cell types.     

Cell surface engineering with polyelectrolyte multilayer thin films

Layer-by-layer assembly of polyelectrolyte multilayer (PEM) films represents a bottom-up approach for re-engineering the molecular landscape of cell surfaces with spatially continuous and molecularly uniform ultrathin films. However, fabricating PEMs on viable cells has proven challenging owing to the high cytotoxicity of polycations. Here, we report the rational engineering of a new class of PEMs with modular biological functionality and tunable physicochemical properties which have been engineered to abrogate cytotoxicity. Specifically, we have discovered a subset of cationic copolymers that undergoes a conformational change, which mitigates membrane disruption and facilitates the deposition of PEMs on cell surfaces that are tailorable in composition, reactivity, thickness, and mechanical properties. Furthermore, we demonstrate the first successful in vivo application of PEM-engineered cells, which maintained viability and function upon transplantation and were used as carriers for in vivo delivery of PEMs containing biomolecular payloads. This new class of polymeric film and the design strategies developed herein establish an enabling technology for cell transplantation and other therapies based on engineered cells.     

Fabrication of surfaces with extremely high contact angle hysteresis from polyelectrolyte multilayer

High contact angle hysteresis on polyelectrolyte multilayers (PEMs) ion-paired with hydrophobic perfluorooctanoate anions is reported. Both the bilayer number of PEMs and the ionic strength of deposition solutions have significant influence on contact angle hysteresis: higher ionic strength and greater bilayer number cause increased contact angle hysteresis values. The hysteresis values of ~100° were observed on smooth PEMs and pinning of the receding contact line on hydrophilic defects is implicated as the cause of hysteresis. Surface roughness can be used to further tune the contact angle hysteresis on the PEMs. A surface with extremely high contact angle hysteresis of 156° was fabricated when a PEM was deposited on a rough substrate coated with submicrometer scale silica spheres. It was demonstrated that this extremely high value of contact angle hysteresis resulted from the penetration of water into the rough asperities on the substrate. The same substrate hydrophobized by chemical vapor deposition of 1H,1H,2H,2H-perfluorooctyltriethoxysilane exhibits high advancing contact angle and low hysteresis.     

Patterned co-culture of primary hepatocytes and fibroblasts using polyelectrolyte multilayer templates

This paper describes the formation of patterned cell co-cultures using the layer-by-layer deposition of synthetic ionic polymers and without the aid of adhesive proteins/ligands such as collagen or fibronectin. In this study, we used synthetic polymers, namely poly(diallyldimethylammonium chloride) (PDAC) and sulfonated polystyrene (SPS) as the polycation and polyanion, respectively, to build the multilayer films. We formed SPS patterns on polyelectrolyte multilayer (PEM) surfaces either by microcontact printing PDAC onto SPS surfaces or vice-versa. To create patterned co-cultures on PEMs, we capitalize on the preferential attachment and spreading of primary hepatocytes on SPS as opposed to PDAC surfaces. In contrast, fibroblasts readily attached to both PDAC and SPS surfaces, and as a result, we were able to obtain patterned co-cultures of fibroblast and primary hepatocytes on synthetic PEM surfaces. We characterized the morphology and hepatic-specific functions of the patterned cell co-cultures with microscopy and biochemical assays. Our results suggest an alternative approach to fabricating controlled co-cultures with specified cell-cell and cell-surface interactions; this approach provides flexibility in designing cell-specific surfaces for tissue engineering applications.     

Characteristics of polyelectrolyte multilayers: effect of PEI anchoring layer and posttreatment after deposition

The influence of a first (anchoring) layer and film treatment on the structure and properties of polyelectrolyte multilayer (PEM) films obtained from polyallylamine hydrochloride (PAH) and polysodium 4-styrenesulfonate (PSS) was studied. Branched polyethyleneimine (PEI) was used as an anchoring layer. The film thickness was measured by ellipsometry. Complementary X-ray reflectometry and AFM experiments were performed to study the change in the interfacial roughness. We found that the thickness of the PEM films increased linearly with the number of layers and depended on the presence of an anchoring PEI layer. Thicker films were obtained for multilayers having PEI as the first layer comparing to films having the same number of layers but consisting of PAH/PSS only. We investigated the wettability of PEM surfaces using direct image analysis of the shape of sessile water drops. Periodic oscillations in contact angle were observed. PAH-terminated films were more hydrophobic than films with PSS as the outermost layer. The effect of long time conditioning of PEM films in solutions of various pH's or salt (NaCl) concentrations was also examined. Salt or base solutions induced modification in wetting properties of the polyelectrolyte multilayers but had a negligible effect on the film thickness.     

In situ ATR-FTIR and SFM Studies on the Influence of Adsorption time on Deposition and Nanostructure of Poly(ethyleneimine)/Poly(acrylic acid) Multilayers

Summary: The deposition and the nanostructure of polyelectrolyte multilayers (PEM) of branched poly(ethyleneimine)/poly(acrylic acid) (PEI/PAC) was studied in dependence of the adsorption time (t_ADS) of the individual steps. PEM were reproducibly deposited applying up to z = 20 adsorption steps at the fixed pH combination of 10/4 and polyelectrolyte concentration c_PEL = 0.005 M in a flow cell using an automated valve system. in situ ATR-FTIR spectroscopy and SFM were used for quantitative determination of deposited amount and thickness, respectively. A linear relation between PEL band integrals and thickness of thin PEM films was found. Varying t_ADS from 0.5 to 5 min in each of the adsorption steps resulted in a steep rise of the deposited PEM amount. For t_ADS > 5 min the deposition did only marginally increase. Evidence for the release of outermost located PEI upon PAC immersion (even step) and of outermost PAC upon PEI immersion (odd step) was obtained. SFM images on consecutively deposited PEM-6 showed a slight increase in structure size and roughness for increasing t_ADS. These studies help to prepare polyelectrolyte based films with controlled thickness for the interaction with biofluids in the biomedical and food field.     

Formation of polyelectrolyte multilayers on fibres: influence on wettability and fibre/fibre interaction

Polydimethyldiallylammonium chloride (PDADMAC) and polystyrene sulfonate (PSS) have been used to build-up polyelectrolyte multilayers (PEMs) on chemical soft wood fibres and on SiO2 at various electrolyte concentrations. Adsorption onto SiO2 was studied using a stagnation point adsorption reflectometer (SPAR), and the adsorbed amount of PDADMAC and PSS on the fibres was determined using nitrogen analysis and Sch?niger burning, respectively. The adsorption onto the two substrates was then compared. Paper testing showed that the tensile index (TI) increased by about 90% when 11 layers had been adsorbed, and that there was a correlation between the adsorbed amount and the increase in TI. It was also shown that the particular polymer present in the outermost layer significantly influenced the TI, and that PDADMAC produced a higher TI. A correlation between the adsorbed amount and the TI was also found. Individual fibres were partly treated with a PEM and analysed using a dynamic contact angle analyser (DCA) and environmental scanning electron microscopy (ESEM).     

Preparation of electrically conducting cellulose fibres utilizing polyelectrolyte multilayers of poly(3,4-ethylenedioxythiophene):poly(styrene sulphonate) and poly(allyl amine)

The primary goal with this work is to create electrically conductive cellulose fibres, this has been done to explore possible new applications for fibre based material. This research uses various methods to create polyelectrolyte multilayers (PEMs) on bleached softwood fibres and on SiO₂ model surfaces, by sequentially treating these materials with poly(3,4-ethylenedioxythiophene):poly(styrene sulphonate) (PEDOT:PSS) and poly(allyl amine) (PAH). Paper sheets were then produced from the PEM-modified pulp and evaluated in terms of tensile strength, adsorbed amount of polymer, and electrical conductivity. To evaluate the influence of fibre charge on the measured paper properties, pulps of two different initial fibre charge densities were prepared via carboxymethylation. Because of the bluish colour of PEDOT:PSS, the build-up of PEM could be easily followed, since the fibres grew increasingly darker blue throughout the modification sequence. The conductivity of the fibre network increased by 2−3 orders of magnitude when the pulp of a higher fibre charge density was used. This suggests that it is more important to create a fibrous network with a high fibre-fibre joint strength and a large total joined area in the sheet rather than to maximize the adsorbed amount of PEDOT:PSS. A difference in conductivity could also be noted depending on the polyelectrolyte adsorbed in the outer layer, PAH lowered the conductivity compared to PEDOT:PSS. Evaluating the mechanical properties revealed that the use of PEDOT:PSS reduces the tensile strength of the paper. When five double layers had been adsorbed onto the carboxymethylated sample in which PEDOT:PSS formed the outer layer, calculations indicated a 25% decrease in tensile strength compared to that of reference material without PEMs. ESEM studies indicate that PEM treatment produces a significantly changed and somewhat smoother fibre surface.     

Controlling the nanofiltration properties of multilayer polyelectrolyte membranes through variation of film composition

We report the use of a variety of polyelectrolyte multilayers (PEMs) as selective skins in composite membranes for nanofiltration (NF) and diffusion dialysis. Deposition of PEMs occurs through simple alternating adsorption of polycations and polyanions, and separations can be optimized by varying the constituent polyelectrolytes as well as deposition conditions. In general, the use of polycations and polyanions with lower charge densities allows separation of larger analytes. Depending on the polyelectrolytes employed, PEM membranes can remove salt from sugar solutions, separate proteins, or allow size-selective passage of specific sugars. Additionally, because of the minimal thickness of PEMs, NF pure water fluxes through these membranes typically range from 1.5 to 3 m3/(m2 day) at 4.8 bar. Specifically, to separate sugars, we employed poly(styrene sulfonate) (PSS)/poly(diallyldimethylammonium chloride) (PDADMAC) films, which allow 42% passage of glucose along with a 98% rejection of raffinose and a pure water flux of 2.4 m3/(m2 day). PSS/PDADMAC membranes are also capable of separating NaCl and sucrose (selectivity of approximately 10), while high-flux chitosan/hyaluronic acid membranes [pure water flux of 5 m3/(m2 day) at 4.8 bar] may prove useful in protein separations.     

Role of chain interpenetration in layer-by-layer deposition of polyelectrolytes

The effects of temperature, pH, and salt concentration on the layer-by-layer (LBL) deposition of sodium poly(styrene sulfonate) (PSS)/poly[2-(dimethylamino)ethyl methacrylate] (PDEM) were investigated by use of a quartz crystal microbalance with dissipation (QCM-D). At pH 4, the frequency change (Deltaf) gradually decreased to a constant, indicating that the polyelectrolyte complexes of the layer were not dissolved. As the layer number increased, the -Deltaf oscillatedly increased, indicating that the thickness of the multilayer increased. At the same time, the dissipation change (DeltaD) oscillatedly increased with the layer number, indicating the chain interpenetration or complexation that led to the alternative swelling-and-shrinking of the outermost layer. For the same layer number, as the temperature increased, the amplitude of DeltaD increased, indicating that the chain interpenetration increased. The thickness also increased with temperature. Further increasing the pH to 7 led to a thicker layer, reflected in the larger amplitude of DeltaD. At pH 10, the polyelectrolytes no longer formed multilayers on the surface because of the lack of electrostatic interactions. On the other hand, the addition of NaCl also led to a thickness increase. The amplitude in DeltaD increased with NaCl concentration, indicating that the chain interpenetration increased. Our experiments indicated that the LBL deposition of polyelectrolytes was dominated by the chain interpenetration. Also, the polyelectrolyte complexes in the layer can redissolve into solution from the surface at a high temperature or a high salt concentration.     

Visco-elastic and adhesive properties of adsorbed polyelectrolyte multilayers determined in situ with QCM-D and AFM measurements

The build-up of multilayers constructed from polyallylamine hydrochloride (PAH) and polyacrylic acid (PAA) under different pH conditions was continuously monitored using the quartz crystal microbalance with dissipation. The adsorbed amount of polymer as well as the amount of coupled water was determined. Furthermore, from dissipation measurements, it was possible to determine the visco-elastic properties of the adsorbed multilayer. These properties were highly dependent on the polyelectrolyte present in the outermost layer. The multilayer was far more rigid and elastic with PAA as the outermost layer. Furthermore, a link has been established between the conformability or rigidity of a multilayer covered surface and the adhesion between such surfaces. Adhesion measurements using the atomic force microscope showed a greater pull-off force when the more viscous PAH was present in the outermost layer.     

Wound Healing Attributes of Polyelectrolyte Multilayers Prepared with Multi‐l‐arginyl‐poly‐l‐aspartate Pairing with Hyaluronic Acid and γ‐Polyglutamic Acid

Biodegradable multi‐l ‐arginyl‐poly‐l ‐aspartate (MAPA), more commonly cyanophycin, prepared with recombinant Escherichia coli contains a polyaspartate backbone with lysine and arginine as side chains. Two assemblies of polyelectrolyte multilayers (PEMs) are fabricated at three different concentration ratios of insoluble MAPA (iMAPA) with hyaluronic acid (iMAPA/HA) and with γ‐polyglutamic acid (iMAPA/γ‐PGA), respectively, utilizing a layer‐by‐layer approach. Both films with iMAPA and its counterpart, HA or γ‐PGA, as the terminal layer are prepared to assess the effect on film roughness, cell growth, and cell migration. iMAPA incorporation is higher for a higher concentration of the anionic polymer due to better charge interaction. The iMAPA/HA films when compared to iMAPA/γ‐PGA multilayers show least roughness. The growth rates of L929 fibroblast cells on the PEMs are similar to those on glass substrate, with no supplementary effect of the terminal layer. However, the migration rates of L929 cells increase for all PEMs. γ‐PGA incorporated films impart 50% enhancement to the cell migration after 12 h of culture as compared to the untreated glass, and the smooth films containing HA display a maximum 82% improvement. The results present the use of iMAPA to construct a new layer‐by‐layer system of polyelectrolyte biopolymers with a potential application in wound dressing.     

Stable superhydrophobic organic-inorganic hybrid films by electrostatic self-assembly

Organic-inorganic hybrid films were prepared through layer-by-layer (LBL) deposition of poly(allylamine hydrochloride) (PAH) and ZrO(2) nanoparticles coated with poly(acrylic acid) (PAA), allowing facile control of surface roughness and hydrophobicity. Superhydrophobic behavior was observed after deposition of silica nanoparticles and a simple fluorination of the surface. The structure of films was controlled by the number of deposition cycles using PAA-coated 100 nm ZrO(2) nanoparticles, the particle size, and the prelayer with PAH and PAA. The change in the apparent water contact angle of (PAH/PAA-coated ZrO(2)n surfaces without fluorination of the surface agrees with Cassie and Baxter's model for nonwetted surfaces even though the outermost surface itself is hydrophilic. Superhydrophobic surfaces were then successfully developed by the deposition of hydrophilic silica nanoparticles on a 10 bilayer surface of PAH/PAA-coated ZrO(2), and a simple fluorination. Moreover, the chemical stability of the film was greatly increased by heat-induced cross-linking of the film. The incorporation of ZrO(2) nanoparticles in superhydrophobic films promises better mechanical properties than the organic film.     

Surface modification of cellulose fibers with layer-by-layer self-assembly of lignosulfonate and polyelectrolyte: effects on fibers wetting properties and paper strength

To convert the hydrophilic cellulose fiber into hydrophobic, multilayers composed of cationic polyacrylamide (CPAM) and lignosulfonate (LS) were constructed on cellulose fiber surface using layer-by-layer (LBL) self-assembly technique. The presence of CPAM/LS multilayers were validated by zeta potential, X-ray photoelectron spectroscopy and atomic force microscopy (AFM). It was found that potential of fiber surface inversed after deposition of each layer, the contents of characteristic elements (i.e. S and N) of CPAM/LS multilayers increased with increasing bilayer number, furthermore, the calculated surface LS content increased linearly as a function of bilayers. AFM phase images indicated that the cellulose microfibrils on fiber surface were gradually covered by LS granules, resulting in an increase in fiber surface roughness as self-assembly proceeded. The wetting properties of modified cellulose fibers were detected by dynamic contact angle measurement. The results showed that the initial water contact angle gradually increased and the attenuation rate of the contact angle gradually decreased with the number of bilayers, suggesting that the controllable hydrophobicity of cellulose fiber can be achieved depending on the number of bilayers. It also showed that the polyelectrolyte presented in the outermost layer significantly influenced the wetting properties of cellulose fibers, and a higher hydrophobicity was observed when LS was in the outermost layer. Moreover, tensile strength test was performed on the handsheet prepared from LBL modified fibers to evaluate the effect of CPAM/LS multilayers on strength property of cellulose fiber networks. The tensile index of handsheet prepared from fibers modified with a (CPAM/LS)₅ multilayer increased by 12.4% compared with that of handsheet prepared from original fibers. The print density of handsheet increased with the number of bilayers, suggesting that printability of the handsheet was improved by constructing CPAM/LS multilayers on cellulose fiber surface. This strategy will have a positive impact and potential application value in printing process control of cellulose fiber-based products.     

由聚电解质自组装多层膜制备微孔薄膜

带有相反电荷的聚电解质通过静电作用交替沉积可以得到自组装多层膜,由于这种技术可操作性强,用途广泛,近十几年来已有了大量的研究．聚电解质多层膜在一定条件下可以形成纳米孔和微米孔．Fu等研究了聚丙烯酸和聚乙烯基吡啶组成的氢键自组装多层膜在碱溶液中溶去其中的聚丙烯酸后,剩下的聚乙烯基吡啶重构形成微孔薄膜．Mendelsohn等发现将聚丙烯酸和聚烯丙基胺自组装而成的多层膜浸入pH=2．4左右的溶液中可制备微孔薄膜．但这些方法并不能使强聚电解质多层膜形成多孔结构。