Synthesis of nitrogen doped activated carbon/polyaniline material for CO2 adsorption

The equilibrium adsorption isotherms of carbon dioxide and nitrogen on the nitrogen doped activated carbon (NAC) prepared by the chemical activation of a pine cone‐based char/polyaniline composite were measured using a volumetric technique. CO₂ and N₂ adsorption experiments were done at three different temperatures (298, 308, and 318 K) and pressures up to 16 bar, and correlated with the Langmuir, Freundlich, and Sips models. The Sips isotherm model presented the best fit to the experimental data. The N‐doped adsorbent showed CO₂ and N₂ adsorption capacity of 3.96 mmol·g⁻¹ and 0.86 mmol·g⁻¹, respectively, at 298 K and 1 bar. The selectivity predicted by ideal adsorbed solution theory (IAST) model was achieved 47.17 for NAC at 1 bar and y_N2 = 0.85 which is a composition similar to flue gas. The results showed that NAC adsorbent has a high CO₂‐over‐N₂ selectivity in a binary mixture. The relatively fast sorption rate of CO₂ on NAC compared to N₂ indicates the stronger affinity between CO₂ and amine groups. The isosteric heat of adsorption of CO₂ by the NAC demonstrated the physico‐chemical adsorption of CO₂ on the adsorbent surface. These data showed that prepared NAC could be successfully applied in separation of CO₂ from N₂.     

Metal Microporous Aromatic Polymers with Improved Performance for Small Gas Storage

A novel metal‐doping strategy was developed for the construction of iron‐decorated microporous aromatic polymers with high small‐gas‐uptake capacities. Cost‐effective ferrocene‐functionalized microporous aromatic polymers (FMAPs) were constructed by a one‐step Friedel–Crafts reaction of ferrocene and s‐triazine monomers. The introduction of ferrocene endows the microporous polymers with a regular and homogenous dispersion of iron, which avoids the slow reunion that is usually encountered in previously reported metal‐doping procedures, permitting a strong interaction between the porous solid and guest gases. Compared to ferrocene‐free analogues, FMAP‐1, which has a moderate BET surface area, shows good gas‐adsorption capabilities for H₂ (1.75 wt % at 77 K/1.0 bar), CH₄ (5.5 wt % at 298 K/25.0 bar), and CO₂ (16.9 wt % at 273 K/1.0 bar), as well as a remarkably high ideal adsorbed solution theory CO₂/N₂ selectivity (107 v/v at 273 K/(0–1.0) bar), and high isosteric heats of adsorption of H₂ (16.9 kJ mol^?1) and CO₂ (41.6 kJ mol^?1).     

Design,synthesis, and gas permeation properties of polyimides containing pendent imidazolium groups

Film‐forming polymers containing ionic groups have attracted considerable attention as emerging materials for gas separation applications. The aim of this article was to synthesize new film‐forming polyimides containing imidazolium groups (PI‐IMs) and establish their structure–performance relationship. In this context, a new aromatic diamine, namely, N¹‐(4‐aminophenyl)‐N¹‐(4‐(2‐phenyl‐1H‐imidazol‐1‐yl)phenyl)benzene‐1,4‐diamine (ImTPADA), was synthesized and polycondensed with three aromatic dianhydrides, namely, 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride, 4,4‐(4,4‐isopropylidenediphenoxy) bis(phthalic anhydride), and 4,4′‐oxydiphthalic anhydride to form the corresponding polyimides containing pendent 2‐phenylimidazole groups (PI‐IEs). Next, PI‐IMs were prepared by N‐quaternization of pendent 2‐phenylimidazole groups present in PI‐6FDA using methyl iodide followed by anion exchange with bis(trifluoromethane)sulfonimide lithium salt (LiTf₂N). PI‐IEs and PI‐IMs exhibited reasonably high molecular weights, amorphous nature, good solubility, and could be cast into self‐standing films from their DMAc solutions. Thermogravimetric analysis showed that 10% weight loss temperature of PI‐IEs and PI‐IMs were in the range 545–475 °C and 303–306 °C, respectively. Gas permeability analysis of films of PI‐IEs and PI‐IMs was investigated by variable‐volume method and it was observed that incorporation of ionic groups into PI‐6FDA resulted in increased permeability while maintaining selectivity. In particular, polymer bearing Tf₂N⁻ anion exhibited high CO₂ permeability (33.3 Barr) and high selectivity for CO₂/CH₄ (41.1) and CO₂/N₂ (35.4). © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1721–1729     

High capacity gas capture and selectivity properties of triazatruxene-based ultramicroporous hyper-crosslinked covalent polymer

Tuning the selective sorption features of microporous organic networks is of great importance for subsequent applications in gas uptake and hiding, while it is more attractive in terms of being both time and cost effective to realize these optimizations without using functional groups in the core and linker. “Knitting” is one of the easiest and most used method to obtain a broad scope of hyper-crosslinked polymers on a large scale from aromatic structures that do not contain functional groups for polymerization. By the use of Knitting method, a hypercrosslinked covalent ultramicroporous organic polymer was obtained via stepwise process from using triazatruxene (TAT) as core -a planar indole trimer- through anhydrous FeCl₃ catalyzed Friedel–Crafts alkylation using dimethoxybenzene as a linker. The resulting microporous polymer, namely TATHCCP was completely identified by analytical and spectral techniques after examined for gas properties (CO₂, CH₄, O₂, CO, and H₂) and selectivity (CO₂/N₂, CO₂/O₂, for CO₂/CO and CO₂/CH₄) up to 1 bar and increased temperatures (273 K, 296 K and 320 K). Although it has a relatively low (Brunauer–Emmett–Teller) BET specific surface area around 557 m²/g, it was seen to have a high CO₂ capture capacity approaching 10% wt. at 273 K. In accordance with (ideal adsorbed solution theory) IAST computations, it was revealed that interesting selectivity features hitting up to 60 for CO₂/N₂, 45 for CO₂/O₂, 35 for CO₂/CO, 13 for CO₂/CH₄ at lower temperatures revealed that the material has much better selectivity values than many HCP (hyper-crosslinked polymer) derivatives in the literature even from its most similar analog dimethoxymethane derivative TATHCP, which has a surface area of 950 m²/g.     

Reaction of carbon dioxide with glycidol: The synthesis of a novel hyperbranched oligomer with a carbonate main chain with a hydroxyl terminal

A novel branched polycarbonate with a hydroxyl group at the chain end was synthesized by the copolymerization of glycidol with carbon dioxide (CO₂). The copolymerization was carried out with 5 mol % of an alkali metal halide or quaternary ammonium salt as a catalyst under atmospheric CO₂. The obtained poly(glycidol‐co‐carbon dioxide) was O‐benzoylated and O‐silylated, and the corresponding polymers were analyzed with IR, size exclusion chromatography, ¹³C NMR, and ²⁹Si NMR. The IR spectroscopy analysis of the O‐benzoylated polymer revealed that the maximum incorporation degree of the carbonate group was 90% (i.e., the CO₂/glycidol composition ratio was 0.9:1.0). The incorporation of CO₂ as a carbonate unit was also confirmed by the treatment of this polymer with n‐butylamine, which caused the aminolysis of the carbonate and led to degraded products. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2506–2511, 2004     

Tuning the adsorption and fluorescence properties of aminal‐linked porous organic polymers through N‐heterocyclic group decoration

Aiming at tuning the adsorption and fluorescence properties of targeted porous organic polymer, four new aminal‐linked porous organic polymers (NAPOPs) were synthesized through the reaction of 1,4‐Bis(4,6‐diamino‐s‐triazin‐2‐yl) benzene (BATB) with four kinds of aldehydes substituted with different N‐heterocyclic groups. Among the polymers, NAPOP‐3 decorated with 5‐phenyl‐tetrazole group shows the largest CO₂ adsorption capacity (2.52 mmol g^?1 at 273 K and 100 kPa) because of its relative large surface area, while NAPOP‐1 decorated with piperazine groups shows relative large CO₂/N₂ adsorption selectivity (77 at 273 K and 100 kPa), attributable to its large CO₂ adsorption heats and cabined pore (<4 Å). Meanwhile, NAPOP‐1 and ?3 exhibit high adsorption rate toward iodine with a high capacity (>240 wt %). In addition, different luminescence emissions were also observed for NAPOPs, indicating different intramolecular charger transfer occurred inside polymer networks. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1724–1730     

Directing the Structural Features of N2‐Phobic Nanoporous Covalent Organic Polymers for CO2 Capture and Separation

A family of azo‐bridged covalent organic polymers (azo‐COPs) was synthesized through a catalyst‐free direct coupling of aromatic nitro and amine compounds under basic conditions. The azo‐COPs formed 3D nanoporous networks and exhibited surface areas up to 729.6 m² g^?1, with a CO₂‐uptake capacity as high as 2.55 mmol g^?1 at 273 K and 1 bar. Azo‐COPs showed remarkable CO₂/N₂ selectivities (95.6–165.2) at 298 K and 1 bar. Unlike any other porous material, CO₂/N₂ selectivities of azo‐COPs increase with rising temperature. It was found that azo‐COPs show less than expected affinity towards N₂ gas, thus making the framework “N₂‐phobic”, in relative terms. Our theoretical simulations indicate that the origin of this unusual behavior is associated with the larger entropic loss of N₂ gas molecules upon their interaction with azo‐groups. The effect of fused aromatic rings on the CO₂/N₂ selectivity in azo‐COPs is also demonstrated. Increasing the π‐surface area resulted in an increase in the CO₂‐philic nature of the framework, thus allowing us to reach a CO₂/N₂ selectivity value of 307.7 at 323 K and 1 bar, which is the highest value reported to date. Hence, it is possible to combine the concepts of “CO₂‐philicity” and “N₂‐phobicity” for efficient CO₂ capture and separation. Isosteric heats of CO₂ adsorption for azo‐COPs range from 24.8–32.1 kJ mol^?1 at ambient pressure. Azo‐COPs are stable up to 350 °C in air and boiling water for a week. A promising cis/trans isomerization of azo‐COPs for switchable porosity is also demonstrated, making way for a gated CO₂ uptake.     

High CO2‐Capture Ability of a Porous Organic Polymer Bifunctionalized with Carboxy and Triazole Groups

A new porous organic polymer, SNU‐C1 , incorporating two different CO₂‐attracting groups, namely, carboxy and triazole groups, has been synthesized. By activating SNU‐C1 with two different methods, vacuum drying and supercritical‐CO₂ treatment, the guest‐free phases, SNU‐C1‐va and SNU‐C1‐sca , respectively, were obtained. Brunauer–Emmett–Teller (BET) surface areas of SNU‐C1‐va and SNU‐C1‐sca are 595 and 830 m²g^?1, respectively, as estimated by the N₂‐adsorption isotherms at 77 K. At 298 K and 1 atm, SNU‐C1‐va and SNU‐C1‐sca show high CO₂ uptakes, 2.31 mmol g^?1 and 3.14 mmol g^?1, respectively, the high level being due to the presence of abundant polar groups (carboxy and triazole) exposed on the pore surfaces. Five separation parameters for flue gas and landfill gas in vacuum‐swing adsorption were calculated from single‐component gas‐sorption isotherms by using the ideal adsorbed solution theory (IAST). The data reveal excellent CO₂‐separation abilities of SNU‐C1‐va and SNU‐C1‐sca , namely high CO₂‐uptake capacity, high selectivity, and high regenerability. The gas‐cycling experiments for the materials and the water‐treated samples, experiments that involved treating the samples with a CO₂‐N₂ gas mixture (15:85, v/v) followed by a pure N₂ purge, further verified the high regenerability and water stability. The results suggest that these materials have great potential applications in CO₂ separation.     

Synthesis of Two‐dimensional Microporous Carbonaceous Polymer Nanosheets and Their Application as High‐performance CO2 Capture Sorbent

The synthesis of two‐dimensional (2D) polymer nanosheets with a well‐defined microporous structure remains challenging in materials science. Here, a new kind of 2D microporous carbonaceous polymer nanosheets was synthesized through polymerization of a very low concentration of 1,4‐dicyanobenzene in molten zinc chloride at 400–500 °C. This type of nanosheets has a thickness in the range of 3–20 nm, well‐defined microporosity, a high surface area (～537 m² g^?1), and a large micropore volume (～0.45 cm³ g^?1). The microporous carbonaceous polymer nanosheets exhibit superior CO₂ sorption capability (8.14 wt % at 298 K and 1 bar) and a relatively high CO₂ selectivity toward N₂ (25.6). Starting from different aromatic nitrile monomers, a variety of 2D carbonaceous polymer nanosheets can be obtained showing a certain universality of the ionothermal method reported herein.     

A Triptycene-Based Porous Organic Polymer that Exhibited High Hydrogen and Carbon Dioxide Storage Capacities and Excellent CO2/N2 Selectivity

A novel porous organic polymer (POP) has been constructed through the condensation of triptycene tricatechol and 1,3,5‐benzenetris(4‐phenylboronic acid). This triptycene‐based POP exhibited high H₂ uptake (up to 1.84 wt% at 77 K, 1 bar), large CO₂ adsorption capacity (up to 18.1 wt% at 273K, 1 bar), and excellent CO₂/N₂ adsorption selectivity (up to 120/1). The influence of solvent on the gas adsorption performance of the POP has also been investigated.     

Investigation of gas transport and other physical properties in relation to the bromination degree of polymers of intrinsic microporosity

In this work, the synthesis of novel polymers of intrinsic microporosity (PIMs) with different degrees of bromine substitution by a free-radical substitution reaction was performed. The synthesized polymers were thoroughly characterized and their bromination degree was verified via nuclear magnetic resonance. The brominated PIMs were investigated by infrared spectroscopy, X-ray diffraction, and density measurements and correlated with their gas transport properties. It was found that with an increase in the bromination degree, the synthesized PIMs exhibited a significant increase in polymer chain packing density which led to reduced fractional free volume and consequent decrease in gas diffusion and permeability coefficients. The change in permeability coefficients caused an improvement in the CO₂/N₂, CO₂/CH₄, and O₂/N₂ ideal permeability selectivities. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 2752–2761     

Synthesis,characterization, and gas permeation properties of adamantane‐containing polymers of intrinsic microporosity

A new bis(catechol) monomer, namely, 4,4′‐((1r,3r)‐adamantane‐2,2‐diyl)bis(benzene‐1,2diol) (THADM) was synthesized by condensation of 2‐adamantanone with veratrole followed by demethylation of the formed (1r,3r)‐2,2‐bis(3,4 dimethoxyphenyl)adamantane. Polycondensation of THADM and various compositions of THADM and 5,5,6′,6′‐tetrahydroxy‐3,3,3′,3′‐tetramethylspirobisindane was performed with 2,3,5,6‐tetrafluoroterephthalonitrile (TFTPN) to obtain the homopolymer and copolymers. These polymers demonstrated good solubility in common organic solvents such as dichloromethane, chloroform, and tetrahydrofuran and could be cast into tough films from their chloroform solutions. GPC analysis revealed that number average molecular weights of polymers were in the range 48,100–61,700 g mol⁻¹, suggesting the formation of reasonably high molecular weight polymers. They possessed intrinsic microporosity with Brunauer‐Emmett‐Teller (BET) surface area in the range 703–741 m² g⁻¹. Thermogravimetric analysis of polymers indicated that 10% weight loss temperature was in the range 513–518 °C demonstrating their excellent thermal stability. THADM‐based polymer of intrinsic microporosity (PIM) showed P(CO₂) = 1080, P(O₂) = 232 and appreciable selectivity [α(CO₂/CH₄) = 22.6, α(CO₂/N₂) = 26.7, and α(O₂/N₂)= 5.7]. The gas permeability measurements revealed that with increase in the content of adamantane units in PIMs, selectivity increased and permeability decreased, following the trade‐off relationship. The gas separation properties of PIMs containing adamantane units were located close to 2008 Robeson upper bound for gas pairs such as CO₂/CH₄, CO₂/N₂, H₂/N₂, and O₂/N₂. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 16–24     

Effect of carbon dioxide sorption on the phase behavior of weakly interacting polymer mixtures: Solvent‐induced segregation in deuterated polybutadiene/polyisoprene blends

The effect of carbon dioxide (CO₂) sorption on the lower critical solution temperatures of deuterated polybutadiene/polyisoprene blends was determined with in situ small‐angle neutron scattering. CO₂ was a poor solvent for both polymers and exhibited very weak selectivity between the blend components. The sorption of modest concentrations of CO₂, at pressures up to 160 bar, induced phase segregation at temperatures well below the binary‐phase‐separation temperature and caused an increased asymmetry in the lower critical solution temperature curve. The origin of solvent‐induced phase segregation in this weakly interacting polymer blend system was attributed predominantly to an exacerbation of the existing disparity in the compressibility of the components upon CO₂ sorption. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3114–3126, 2003     

Selective CO2 Sorption Using Compartmentalized Coordination Polymers with Discrete Voids**

Carbon capture and storage with porous materials is one of the most promising technologies to minimize CO₂ release into the atmosphere. Here, we report a family of compartmentalized coordination polymers (CCPs) capable of capturing gas molecules in a selective manner based on two novel tetrazole-based ligands. Crystal structures have been modelled theoretically under the Density Functional Theory (DFT) revealing the presence of discrete voids of 380 ų. Single gas adsorption isotherms of N₂, CH₄ and CO₂ have been measured, obtaining a loading capacity of 0.6, 1.7 and 2.2 molecules/void at 10 bar and at 298 K for the best performing material. Moreover, they present excellent selectivity and regenerability for CO₂ in mixtures with CH₄ and N₂ in comparison with other reported materials, as evidenced by dynamic breakthrough gas experiments. These frameworks are therefore great candidates for separation of gas mixtures in the chemical engineering industry.     

Novel fixed‐site–carrier polyvinylamine membrane for carbon dioxide capture

Fixed‐site–carrier membranes were prepared for the facilitated transport of CO₂ by casting polyvinylamine (PVAm) on various supports, such as poly(ether sulfone) (PES), polyacrylonitrile (PAN), cellulose acetate (CA), and polysulfone (PSO). The cast PVAm on the support was crosslinked by various methods with glutaraldehyde, hydrochloric acid, sulfuric acid, and ammonium fluoride. Among the membranes tested, the PVAm cast on polysulfone and crosslinked by ammonium fluoride showed the highest selectivity of CO₂ over CH₄ (>1000). The permeance of CO₂ was then measured to be 0.014 m³ (STP)/(m² bar h) for a 20 μm thick membrane. The effect of the molecular weight of PVAm and feed pressure on the permeance was also investigated. The selectivity increased remarkably with increasing molecular weight and decreased slightly with increased pressure in the range of 1 to 4 bar. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4326–4336, 2004     

Effects of tertiary amines and quaternary ammonium halides in polysulfone on membrane gas separation properties

Polymers containing CO₂‐philic groups are of great interest for CO₂/light gas separation membranes because the affinity toward CO₂ can effectively increase CO₂ solubility and thus permeability. In this study, polysulfones (PSUs) modified with different degrees of benzyldimethylamine (DMA), benzyltrimethylammonium fluoride (TMAF), and benzyltrimethylammonium iodide (TMAI) were synthesized using sequential post‐functionalization reactions and investigated for CO₂/N₂ and CO₂/CH₄ separation. The physical properties of these polymers were studied, including density, fractional free volume, and glass transition temperature. In contrast to the conventional wisdom that tertiary amines exhibit an affinity toward CO₂, this study convincingly shows that the DMA substituent has a minimal impact on CO₂ solubility and CO₂/light gas solubility selectivity in PSUs under dry condition. On the other hand, incorporating TMAF and TMAI in PSU significantly increases CO₂ solubility. Particularly, introducing TMAI with a molar ratio of 1.07 relative to PSU repeating units increases CO₂/CH₄ solubility from 4.4 to 5.2, CO₂/CH₄ permeability selectivity from 21 to 45, and CO₂/N₂ permeability selectivity from 24 to 33 at 35 °C, while the CO₂ permeability decreases from 5.6 to 1.7 Barrers. The effect of these functional groups in PSUs on gas diffusivity and diffusivity selectivity can be satisfactorily described by the free volume model. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 1239–1250     

Poly(ionic liquid)s as new materials for CO2 absorption

A series of imidazolium‐based ionic liquid monomers and their corresponding polymers (poly(ionic liquid)s) were synthesized, and their CO₂ sorption was studied. The poly(ionic liquid)s had enhanced CO₂ sorption capacities and fast sorption/desorption rates compared with room temperature ionic liquids. The effects of the chemical structures, including the types of anion, cation, and backbone of the poly(ionic liquid)s on their CO₂ sorption have been discussed. In contrast to room temperature ionic liquids, the polymer with PF anions had the highest CO₂‐sorption capacity, while those with BF or Tf₂N^? anions had the same capacities. The CO₂ sorption and desorption of the polymers were fast and reversible, and the sorption was selective over H₂, N_2, and O₂. The measured Henry's constants of P[VBBI][BF₄] and P[MABI][BF₄] were 26.0 bar and 37.7 bar, which were lower than those of similar room temperature ionic liquids. The preliminary study of the mechanism indicated that the CO₂ sorption of the polymer particles was more absorption (the bulk) but less adsorption (the surface). © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5477–5489, 2005     

Dynamic Entangled Porous Framework for Hydrocarbon (C2–C3) Storage,CO2 Capture,and Separation

Storage and separation of small (C1–C3) hydrocarbons are of great significance as these are alternative energy resources and also can be used as raw materials for many industrially important materials. Selective capture of greenhouse gas, CO₂ from CH₄ is important to improve the quality of natural gas. Among the available porous materials, MOFs with permanent porosity are the most suitable to serve these purposes. Herein, a two‐fold entangled dynamic framework {[Zn₂(bdc)₂(bpNDI)]?4DMF}_n with pore surface carved with polar functional groups and aromatic π clouds is exploited for selective capture of CO₂, C2, and C3 hydrocarbons at ambient condition. The framework shows stepwise CO₂ and C₂H₂ uptake at 195 K but type I profiles are observed at 298 K. The IAST selectivity of CO₂ over CH₄ is the highest (598 at 298 K) among the MOFs without open metal sites reported till date. It also shows high selectivity for C₂H₂, C₂H₄, C₂H₆, and C₃H₈ over CH₄ at 298 K. DFT calculations reveal that aromatic π surface and the polar imide (RNC=O) functional groups are the primary adsorption sites for adsorption. Furthermore, breakthrough column experiments showed CO₂/CH₄ C₂H₆/CH₄ and CO₂/N₂ separation capability at ambient condition.     

Shape-Memory Effect Enabled by Ligand Substitution and CO2 Affinity in a Flexible SIFSIX Coordination Network

We report that linker ligand substitution involving just one atom induces a shape-memory effect in a flexible coordination network. Specifically, whereas SIFSIX-23-Cu, [Cu(SiF₆)(L)₂]_n, (L=1,4-bis(1-imidazolyl)benzene, SiF₆²⁻=SIFSIX) has been previously reported to exhibit reversible switching between closed and open phases, the activated phase of SIFSIX-23-Cu^N, [Cu(SiF₆)(L^N)₂]_n (L^N=2,5-bis(1-imidazolyl)pyridine), transformed to a kinetically stable porous phase with strong affinity for CO₂. As-synthesized SIFSIX-23-Cu^N, α, transformed to less open, γ, and closed, β, phases during activation. β did not adsorb N₂ (77 K), rather it reverted to α induced by CO₂ at 195, 273 and 298 K. CO₂ desorption resulted in α′, a shape-memory phase which subsequently exhibited type-I isotherms for N₂ (77 K) and CO₂ as well as strong performance for separation of CO₂/N₂ (15/85) at 298 K and 1 bar driven by strong binding (Q_st=45–51 kJ/mol) and excellent CO₂/N₂ selectivity (up to 700). Interestingly, α′ reverted to β after re-solvation/desolvation. Molecular simulations and density functional theory (DFT) calculations provide insight into the properties of SIFSIX-23-Cu^N.     

Genuine Pores in a Stable Zinc Phosphite for High H2 Adsorption and CO2 Capture

An uncommon example of stable mixed-ligand zinc phosphite with genuine pores has been synthesized by using zinc metal, inorganic phosphite acid, thio-functionalized O-donor (2,5-thiophenedicarboxylate, TPDC), and tetradentate N-donor [1,2,4,5-tetrakis(imidazol-1-ylmethyl)benzene, TIMB] units assembled into one crystalline structure according to a hydro(solvo)thermal method. This is a very rare case of a metal phosphite incorporating both N- and O-donor ligands. The tetradentate TIMB linker bound to zinc atoms of the isolated zincophosphite hexamers to form a 3D open-framework structure by crosslinking structural components of 1D chains and 2D layers. Here, the TPDC ligand acts as a monodentate binding model to functionalize its porous structure with the uncoordinated S atom and COO⁻ group. Interestingly, this compound demonstrates the highest H₂ storage capacity among organic–inorganic hybrid metal phosphates (and phosphites), and a good CO₂ capture at 298 K compared with the majority of crystalline materials. The possible adsorption sites and selectivity for CO₂ over H₂, N₂, and CO at 298 K were calculated by using density functional theory (DFT), the ideal adsorption solution theory (IAST), and fitting experimental pure-component adsorption data.