Synthesis of oligo(ethylene glycol) methacrylate polymer brushes

Here we report a study into controlling the polymerization of mono-hydroxy and mono-methoxy terminated oligo(ethylene glycol) methacrylates (HOEGMA and MeOEGMA, respectively) from functionalised, planar surfaces via atom transfer radical polymerization (ATRP). The effects of initiator structure, initiator density, temperature, and monomer ratios have been investigated for these polymerizations. The polymer brushes grown in this way were found to convey protein resistance to the underlying inorganic substrates, prone to facile protein adsorption in their native state.     

Revealing the effect of oligo(ethylene glycol) side chains on n-doping process in FBDPPV-based polymers

The low doping efficiency of n-doped systems limits the development of n-type organic conducting materials. Oligo(ethylene glycol) (OEG) as the flexible chain in conjugated small molecules and polymers may improve doping efficiency. However, OEG side chains also bring unexpected low mobility and poor film morphology. Herein, we propose the stronger solution-state aggregation plays a dominated role in charge transport and morphology of OEG-substituted polymer. The solution-state aggregation also affects doping process. Therefore, we develop a series of polymers based on 3,7-bis((E)-7-fluoro-1-(2-octyldodecyl)-2-oxoindolin-3-ylidene)-3,7-dihydrobenzo[1,2-b:4,5-b']difuran-2,6-dione (FBDPPV) with different ratios of OEG side chain to investigate the effect of side chain on solution-state aggregation and n-doping process. After n-doped by hexahydro-1H,3a1H,4H,7H-3a,6a,9a-triazaphenalene (TAM), FBDPPV with 50% OEG affords the highest doping efficiency and conductivity, while FBDPPV with 100% OEG shows lower conductivity. Combination of ultraviolet–visible–near infrared absorption spectra, grazing-incidence wide-angle X-ray scattering and atomic force microscopy, we reveal that serious aggregated extent in solution of OEG-substituted polymer result in phase separation and rough morphology, which are the origins of poor conductivity. Our work provides a new perspective on the effect of the OEG side chain on the doped polymer systems, suggesting suitable solution-state aggregation is crucial to high doping efficiency and high conductivity.     

(Co)polymers of oligo(ethylene glycol) methacrylates—temperature‐induced aggregation in aqueous solution

The synthesis and aggregation behavior of well‐defined thermosensitive (co)polymers of oligo(ethylene glycol) methacrylates (POEGMA) in aqueous solutions were investigated. The cloud points of the POEGMAs solutions were determined by turbidimetry and dynamic light scattering. For POEGMA (co)polymers the cloud point temperature (T_CP) increased linearly with increasing content of more hydrophilic comonomer. The mesoglobules formed by POEGMAs in dilute aqueous solutions above T_CP were studied by light scattering. The size of mesoglobules depended on the concentration and the heating procedures. The aggregates became smaller with decreasing initial concentration of polymer and increasing rates of temperature change. By selecting the proper heating and dilution procedures, the influence of the (co)polymer structure on the size of the mesoglobules could be determined. The size of the mesoglobules decreased with the length of the OEG side chains and increased with increasing content of more hydrophilic comonomer. The light scattering parameters of the mesoglobules—A₂ values and shape factors ${R_{\rm g}\over R_{\rm h}}$ —suggested that the hydrophilic OEG side chains placed at the periphery of the mesoglobules in direct contact with the surrounding water controlled the size of mesoglobules and their stability. Shape factors for all POEGMA mesoglobules indicated that the mesoglobules remained highly hydrated after formation. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Thermoresponsive gene carriers based on polyethylenimine-graft-poly[oligo(ethylene glycol) methacrylate

A family of thermoresponsive cationic copolymers (TCPs) that contain branched PEI 25 K as the cationic segment and poly(MEO(2)MA-co-OEGMA(475)) as the thermosensitive block (TP) is prepared. The DNA binding capability, physicochemical properties, and biological performance of the TCPs are studied. All of these TCPs can condense DNA to form polyplexes with diameters of 150-300 nm and zeta potentials of 7-32 mV at N/P ratios between 12 and 36. The length of TP block is a key factor for shielding the positive surface charge of the polyplexes and protecting them against protein adsorption. TCPs with a higher TP content have a lower cytotoxicity while the best transfection performance is achieved by the TCPs with longest TP length, reaching a level of the intact PEI 25 K in the presence of serum.     

Poly(ethylene glycol)-based shape-memory polymers

Poly(ethylene glycol) (PEG) blends photo-curable and thermal activated shape-memory polymers (SMPs), with different activation temperature (T_switch), have been synthesized and characterized. PEG blends with different molecular weights were chain-end functionalized with isocyanate ethyl methacrylate and photo-cured with UV lamp. Degree of cross-linking of the blend network, determined by gel content measurement, resulted as higher than 95%. The thermal and thermomechanical properties of these SMPs PEG blends were characterized by differential scanning calorimetry and dynamic mechanical analysis. The shape-memory properties of the networks were quantified using thermomechanical three-point bending experiments and showed strain fixity rates higher than 99% and a minimum strain recovery ratio of 82%.     

聚乙二醇支载的杂环化合物库的液相合成

随着组合化学的迅速发展, 兼容固相合成和溶液相合成优点的液相合成方法已成为实现组合化学的一条重要途径. 综述了近年来聚乙二醇为可溶性聚合物载体支载的杂环化合物库的研究, 并展望了其今后的发展方向.     

Preparation of interpenetrating polymer network composed of poly(ethylene glycol) and poly(acrylamide) hydrogels as a support of enzyme immobilization

Poly(ethylene glycol)(PEG)‐based interpenetrating polymeric network (IPN) hydrogels were prepared for the application of enzyme immobilization. Poly(acrylamide)(PAAm) was chosen as the other network of IPN hydrogel and different concentration of PAAm networks were incorporated inside the PEG hydrogel to improve the mechanical strength and provide functional groups that covalently bind the enzyme. Formation of IPN hydrogels was confirmed by observing the weight per cent gain of hydrogel after incorporation of PAAm network and by attenuated total reflectance/Fourier transform infrared (ATR/FTIR) analysis. Synthesis of IPN hydrogels with higher PAAm content produced more crosslinked hydrogels with lower water content (WC), smaller M_c and mesh size, which resulted in enhanced mechanical properties compared to the PEG hydrogel. The IPN hydrogels exhibited tensile strength between 0.2 and 1.2 MPa while retaining high levels of hydration (70–81% water). For enzyme immobilization, glucose oxidase (GOX) was immobilized to PEG and IPN hydrogel beads. Enzyme activity studies revealed that although all the hydrogels initially had similar enzymatic activity, enzyme‐immobilizing PEG hydrogels lost most of the enzymatic activity within 2 days due to enzyme leaching while IPN hydrogels maintained a maximum 80% of the initial enzymatic activity over a week due to the covalent linkage between the enzyme and amine groups of PAAm. Copyright © 2008 John Wiley & Sons, Ltd.     

Micellization and Thermogelation of Poly(ether urethane)s Comprising Poly(ethylene glycol) and Poly(propylene glycol)

A series of multiblock poly(ether urethane)s comprising poly(ethylene glycol) (PEG), and poly(propylene glycol) (PPG) segments were synthesized. Their aqueous solutions exhibited thermogelling behavior at critical gelation concentrations (CGC) ranging from 8 to 12 wt%. The composition and structural information of the copolymers were studied by GPC and ¹H NMR. The critical micellization concentration (CMC) and thermodynamic parameters for micelle formation were determined at different temperatures. The temperature response of the copolymer solutions were studied and found to be associated with the composition of the copolymers.     

Synthesis and characterization of poly(ethylene glycol) methyl ether endcapped poly(ethylene terephthalate)

Linear and branched poly(ethylene terephthalate) (PET) copolymers with polyethylene glycol) (PEG) methyl ether (700 or 2000 g/mol) end groups were synthesized using conventional melt polymerization. DSC analysis demonstrated that low levels of PEG end groups accelerated PET crystallization. The incorporated PEG end groups also decreased the crystallization temperature of PET dramatically, and copolymers with a high content of PEG (>17.6 wt%) were able to crystallize at room temperature. Rheological analysis demonstrated that the presence of PEG end groups effectively decreased the melt viscosities and facilitated melt processing. XPS and ATR-FTIR revealed that the PEG end groups tended to aggregate on the surface, and the surface of compression molded films containing 34.0 wt% PEG were PEG rich (85 wt% PEG). PEG end-capped PET (34.0 wt% PEG) and PET films were immersed into a fibrinogen solution (0.7 mg/mL BSA) for 72 h to investigate the propensity for protein adhesion. XPS demonstrated that the concentration of nitrogen (1.05%) on the surface of PEG endcapped PET film was statistically lower than PET (7.67%). SEM analysis was consistent with XPS results, and revealed the presence of adsorbed protein on the surface of PET films.     

Amphiphilic comb-shaped polymers from poly(ethylene glycol) macromonomers

Comb-shaped amphiphilic graft copolymers composed of hydrophobic backbones and hydrophilic side chains were prepared by radical copolymerization of poly(ethylene glycol) monomethacrylate macromonomers, and methacrylate and acrylate comonomers in toluene. The copolymerizations were very sensitive to the reaction conditions, and insoluble cross-linked gels were easily formed. The yields of soluble copolymers were affected by the initiator concentration, the macromonomer concentration, and the choice of chain transfer agents and comonomers. Solubilities of the copolymers in water or methanol were found to depend on the sizes and the numbers of the PEG side chains. The copolymers showed surface activity with CMC:s in the order of 0.1–1.5 g/L and surface tensions of 36–56 dyn/cm. When tested as emulsifiers most of the copolymers gave oil-in-water type emulsions at room temperature. Polymers carrying MPEG 2000 side chains were crystalline with melting points of 38–44°C, while those based on PEG 400 and 1000 were mostly amorphous with glass transition temperatures between -55 and -60°C. © 1992 John Wiley & Sons, Inc.     

PEG／PED-g-CB化学敏电阻材料的制备及其气敏性能的研究

以不同分子量聚乙二醇(PEG)为基体，PEG接枝改性的炉法炭黑(PEG-g-CB)为导电裁流子，采用溶液分散工艺制得一种新鞭的气敏传感器材料。研究了PEG分子量对接枝率及对各种溶剂蒸气的响应性、响应灵敏度的影响；用透射电子显微镜(TEM)和紫外—可见分光光度计考察了两种炭黑粒子分散行为、袁面特性差异及其对响应重复性、稳定性的影响。结果表明，PEG／PEG-g-CB复合材料化学敏电阻体对其良溶剂蒸气如THF、氯仿、丙酮具有很强的响应性，其电阻值可提高到初始电阻的10^4～10^6倍。将这种材料再放入干燥空气中时，电阻又恢复到初始值；而对其不良溶剂如正己烷、甲苯几乎不响应。随PEG分子量的提高，响应灵敏度下降；响应的重复稳定性受炭黑粒子分散行为的影响，从聚合物溶胀行为及逾渗导电理论解释了实验结果。     

Segmented block copolymers of poly(ethylene glycol) and poly(ethylene terephthalate)

A new series of segmented copolymers were synthesized from poly(ethylene terephthalate) (PET) oligomers and poly(ethylene glycol) (PEG) by a two‐step solution polymerization reaction. PET oligomers were obtained by glycolysis depolymerization. Structural features were defined by infrared and nuclear magnetic resonance (NMR) spectroscopy. The copolymer composition was calculated via ¹H NMR spectroscopy. The content of soft PEG segments was higher than that of hard PET segments. A single glass‐transition temperature was detected for all the synthesized segmented copolymers. This observation was found to be independent of the initial PET‐to‐PEG molar ratio. The molar masses of the copolymers were determined by gel permeation chromatography (GPC). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4448–4457, 2004     

Thermoresponsive oligo(ethylene glycol) methacrylate colloids with antifouling surface properties

Thermoresponsive polymeric colloids attract great attention in several biotechnological applications owing to their ability to manipulate drug release characteristics in a controlled manner. Majority of these applications utilized N‐isopropylacrylamide (NIPAM)‐based particles for controlled drug release. Despite its advantages, such as easy chemical modification and well‐documented literature, a potentially important bottleneck for NIPAM in biological applications is its tendency for nonspecific protein adsorption. Herein, we report a simple way to prepare novel thermoresponsive colloids composed of oligo(ethylene glycol) side chains via precipitation polymerization technique. In addition to displaying highly reversible thermal response, these particles also have considerably low nonspecific protein adsorption when compared with NIPAM counterparts. These crosslinked poly(ethylene glycol) ethyl ether methacrylate particles were characterized using dynamic light scattering and transmission electron microscopy. The effects of co‐monomer, crosslinker and initiator on particle characteristics were investigated. Finally, particle toxicity studies were carried out using 3T3 fibroblast cell lines in MTT cytotoxicity assay. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

紫外光交联可降解聚对二氧环己酮/聚乙二醇薄膜制备与表征

以2,2-二甲氧基-2-苯基苯乙酮(DMPA)为引发剂,将四臂端丙烯酸酯聚对二氧环己酮(PPDO-4AC)和聚乙二醇双丙烯酸酯(PEG-DA)经紫外光照射制得PPDO/PEG交联薄膜.研究了光照时间和DMPA用量对PPDO/PEG交联薄膜凝胶含量的影响.DSC研究表明共聚物中两组分的相容性较好,Tg随着共聚物中PEG链...     

新型结合阿霉素的聚乙二醇嵌段共聚树枝状聚赖氨酸的合成及其药物缓释行为的研究

采用液相多肽合成方法, 成功制备得到窄分子量分布、结构确定的聚乙二醇嵌段共聚四代树枝状聚赖氨酸 (MPEG-block-DPL4). 在此基础上, 进一步将其DPL4的端氨基转化为端肼基, 并通过其与抗肿瘤药物阿霉素(DOX) C＝O的反应形成C＝N键, 实现在DPL4表面的阿霉素药物分子化学结合, 最终得到新型pH敏感性的高分子药物MPEG-block-DPL4-CONHN＝DOX. 运用紫外分光光度(UV-Vis)法, 对MPEG-block-DPL4-CONHNH₂与阿霉素的负载效率进行了定量分析. 高分子药物MPEG-block-DPL4-CONHN＝DOX在生理条件(pH＝7.4)下相对稳定, 而弱酸性条件(pH＝4.5, 5.5)下, C＝N键能较快水解, 释放阿霉素药物分子. 体外细胞毒性评价结果表明(细胞株SMMC-7721和SPCA-1), 所得新型高分子药物MPEG-block-DPL4-CONHN＝DOX的细胞毒性显著地低于游离阿霉素药物分子, 因此, 可进一步研究发展成为新型pH敏感性可控缓释高分子抗肿瘤药物载体体系.     

Multifunctional Poly(ethylene glycol)s

In the rapidly evolving multidisciplinary field of polymer therapeutics, tailored polymer structures represent the key constituent to explore and harvest the potential of bioactive macromolecular hybrid structures. In light of the recent developments for anticancer drug conjugates, multifunctional polymers are becoming ever more relevant as drug carriers. However, the potentially best suited polymer, poly(ethylene glycol) (PEG), is unfavorable owing to its limited functionality. Therefore, multifunctional linear copolymers (mf‐PEGs) based on ethylene oxide (EO) and appropriate epoxide comonomers are attracting increased attention. Precisely engineered via living anionic polymerization and defined with state‐of‐the‐art characterization techniques—for example real‐time ¹H NMR spectroscopy monitoring of the EO polymerization kinetics—this emerging class of polymers embodies a powerful platform for bio‐ and drug conjugation.     

Structural analysis of poly(amidoamine) dendrimer immobilized in crosslinked poly(ethylene glycol)

Polymeric membranes comprised of poly(amidoamine) (PAMAM) dendrimer immobilized in a poly(ethylene glycol) (PEG) network exhibit an excellent CO₂ separation selectivity over H₂. The CO₂ permeability increases with PAMAM dendrimer concentration in the polymeric membrane and becomes 500 times greater than H₂ permeability when the dendrimer content was 50 wt % at ambient conditions (5 kPa of CO₂ partial pressure). However, the detailed morphology of the membrane has not been discussed. The immiscibility of PAMAM dendrimer and PEG matrix results in phase separation, which takes place in a couple of microns scale. Especially, laser scanning confocal microscope captures a 3D morphology of the polymeric blend. The obtained 3D reconstructions demonstrate a bicontinuous structure of PAMAM dendrimer‐rich and PEG‐rich phases, which indicates the presence of PAMAM dendrimer channel penetrating the polymeric membrane, and CO₂ will preferentially pass through the dendrimer channel. In addition, Fourier transform of the 3D reconstructions indicates the presence of a periodic structure. An average size of the dendrimer domain calculated is 2–4 μm in proportion to PAMAM dendrimer concentration. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Poly (caprolactone)/poly (ethylene glycol) pervaporation blend membranes: Synthesis,characterization, and performance

Poly (caprolactone) membranes with addition of different poly (ethylene glycol) concentrations were prepared for separation of water/isopropanol azeotropic mixture by pervaporation process. Different characterization tests including Fourier transform infrared, scanning electron microscopy, water contact angle, and thermogravimetric analysis were carried out on the prepared membranes. In addition, the effect of poly (ethylene glycol) PEG content on the swelling degree and the performance of the prepared membranes in pervaporation process were investigated. According to the obtained results, all the membranes were water selective and the blend membrane containing 3 wt% PEG exhibited the best pervaporation performance with a water flux of 0.517 kg/m² hour and separation factor of 1642 at the ambient temperature. Hydrophilicity improvement of the blend membranes was confirmed by constant decrease in water contact angle of the membranes as PEG content increased in the casting solution. Scanning electron microscopy cross‐sectional images indicated that the blend membranes containing PEG had a closed cellular structure. Furthermore, mechanical and thermal properties of the membranes decreased by adding PEG.     

New Poly(propylene glycol)‐ and Poly(ethylene glycol)‐Based Polymer Gelators with L‐Lysine

Summary: New polymer gelators consisting of poly(propylene glycol) or poly(ethylene glycol) and L ‐lysine‐based low‐molecular‐weight gelators have been developed. These polymer gelators were synthesized according to a simple procedure with high reaction yield, and formed organogels in many organic solvents. The organogelation mechanism was proposed from the transmission electron microscopy and FTIR spectroscopy studies.

Structures of the polymer gelators synthesized here.