The SAMBA quick‐EXAFS monochromator: XAS with edge jumping

Results and performances of the QEXAFS double monochromator of the SAMBA beamline (Synchrotron SOLEIL) are presented. The device is capable of speeds of up to 40 Hz, while giving the user the possibility to choose the amplitude of the scan from 0.1° to 4° in a few seconds. The device is composed of two independent units and it is possible to perform scans alternating between two different crystals, literally jumping from low (4 keV) to high (37 keV) energies.     

Energy‐resolved electron‐yield XAS studies of nanoporous CoAlPO‐18 and CoAlPO‐34 catalysts

Energy‐resolved electron‐yield X‐ray absorption spectroscopy is a promising technique for probing the near‐surface structure of nanomaterials because of its ability to discriminate between the near‐surface and bulk of materials. So far, the technique has only been used in model systems. Here, the local structural characterization of nanoporous cobalt‐substituted aluminophosphates is reported and it is shown that the technique can be employed for the study of open‐framework catalytically active systems. Evidence that the cobalt ions on the surface of the crystals react differently to those in the bulk is found.     

Polycapillary‐optics‐based micro‐XANES and micro‐EXAFS at a third‐generation bending‐magnet beamline

A focusing system based on a polycapillary half‐lens optic has been successfully tested for transmission and fluorescence µ‐X‐ray absorption spectroscopy at a third‐generation bending‐magnet beamline equipped with a non‐fixed‐exit Si(111) monochromator. The vertical positional variations of the X‐ray beam owing to the use of a non‐fixed‐exit monochromator were shown to pose only a limited problem by using the polycapillary optic. The expected height variation for an EXAFS scan around the Fe K‐edge is approximately 200 µm on the lens input side and this was reduced to ～1 µm for the focused beam. Beam sizes (FWHM) of 12–16 µm, transmission efficiencies of 25–45% and intensity gain factors, compared with the non‐focused beam, of about 2000 were obtained in the 7–14 keV energy range for an incoming beam of 0.5 × 2 mm (vertical × horizontal). As a practical application, an As K‐edge µ‐XANES study of cucumber root and hypocotyl was performed to determine the As oxidation state in the different plant parts and to identify a possible metabolic conversion by the plant.     

Beam‐size‐related phenomena and effective normalization in energy‐dispersive EXAFS for the study of heterogeneous catalysts,powder materials and the processes they mediate: observations and (some) solutions

The effects of focal spot size and the nature of powder samples (such as heterogeneous catalysts) on the quality of data obtainable from a dispersive EXAFS experiment are characterized at ID24 of the ESRF. Using examples of supported Pd catalysts, it is shown that, for a given photon flux, massive improvements in data quality can be achieved by increasing the size of the dispersive beam in the vertical, whilst concurrently applying a methodology to account for scattering effects emanating from the samples under study. These improvements are demonstrated using progressively practical and demanding examples. Questions regarding optimal beam dimensions for the study of such materials, how to counter undesirable effects that arise from the coherence of the source, how to obtain similar results consistently across the 5–30 keV bandwidth of ID24, and whether a methodology for simultaneous normalization in dispersive EXAFS is of significant utility in such circumstances are discussed.     

Pump−probe experiments at the TEMPO beamline using the low‐α operation mode of Synchrotron SOLEIL

The SOLEIL synchrotron radiation source is regularly operated in special filling modes dedicated to pump–probe experiments. Among others, the low‐α mode operation is characterized by shorter pulse duration and represents the natural bridge between 50 ps synchrotron pulses and femtosecond experiments. Here, the capabilities in low‐α mode of the experimental set‐ups developed at the TEMPO beamline to perform pump–probe experiments with soft X‐rays based on photoelectron or photon detection are presented. A 282 kHz repetition‐rate femtosecond laser is synchronized with the synchrotron radiation time structure to induce fast electronic and/or magnetic excitations. Detection is performed using a two‐dimensional space resolution plus time resolution detector based on microchannel plates equipped with a delay line. Results of time‐resolved photoelectron spectroscopy, circular dichroism and magnetic scattering experiments are reported, and their respective advantages and limitations in the framework of high‐time‐resolution pump–probe experiments compared and discussed.     

Time‐resolved in situ tomography for the analysis of evolving metal‐foam granulates

An experimental setup has been developed that allows for capturing up to 25 tomograms s^?1 using the white X‐ray beam at the experimental station EDDI of BESSY II, Berlin, Germany. The key points are the use of a newly developed, precise and fast rotation stage, a very efficient scintillator and a fast CMOS camera. As a first application, the foaming of aluminium alloy granules at 923 K was investigated in situ. Formation and growth of bubbles in the liquid material were observed and found to be influenced by the limited thermal conductivity in the bulk granules. Changes that took place between two tomographic frames separated in time by 39 ms could be detected and analysed quantitatively.     

Angle‐resolved photoemission spectroscopy and imaging with a submicrometre probe at the SPECTROMICROSCOPY‐3.2L beamline of Elettra

The extensive upgrade of the experimental end‐station of the SPECTROMICROSCOPY‐3.2L beamline at Elettra synchrotron light source is reported. After the upgrade, angle‐resolved photoemission spectroscopy from a submicrometre spot and scanning microscopy images monitoring the photoelectron signal inside selected acquisition angle and energy windows can be performed. As a test case, angle‐resolved photoemission spectroscopy from single flakes of highly oriented pyrolitic graphite and imaging of the flakes with image contrast owing to rotation of the band dispersion of different flakes are presented.     

Time‐resolved Raman studies on Al2O3: Cr3+: lifetime measurements of the excited‐state transition Ē → 2Ā

A time‐resolved intensified charge coupled device‐based Raman microspectrometer system dedicated to the study of solid samples is described, offering good optical, temporal and spatial resolution. The advantages of this approach are demonstrated on Al₂O₃:Cr³⁺, obtaining for the first time the temporal evolution of the excited state transition Ē → 2Ā. Moreover, the time dependence of the luminescence due to the chromium ion was also determined by the same Raman device. Copyright © 2010 John Wiley & Sons, Ltd.     

Rate constant measurements for initial addition reactions of radicals at the propagation step of photo‐polymerization as studied by pulsed EPR spectroscopy

Pulsed EPR spectroscopy was employed to determine reaction rate constants at an early stage of addition reactions in radical polymerizations triggered by four initiator radicals, which were generated by photodissociation of four parent molecules. Two monomers (tert‐butylacrylate and tert‐butylmethacrylate) were examined as reactant. Stern–Volmer analysis on the measured decay time of electron spin echo intensity of reacting radicals provides rate constants for addition reactions. We focused on rate constants for the second step reaction between monomer and adduct radical that is produced by the first step addition reaction between initiator radical and monomer. The rate constant measured by pulsed EPR was evaluated by theoretical calculations in the light of (1) enthalpy difference between product radical and reactants and (2) charge transfer interaction between reacting radical and monomer. Copyright © 2016 John Wiley & Sons, Ltd.     

Position and flux stabilization of X‐ray beams produced by double‐crystal monochromators for EXAFS scans at the titanium K‐edge

The simultaneous and active feedback stabilization of X‐ray beam position and monochromatic beam flux during EXAFS scans at the titanium K‐edge as produced by a double‐crystal monochromator beamline is reported. The feedback is generated using two independent feedback loops using separate beam flux and position measurements. The flux is stabilized using a fast extremum‐searching algorithm that is insensitive to changes in the synchrotron ring current and energy‐dependent monochromator output. Corrections of beam height are made using an innovative transmissive beam position monitor instrument. The efficacy of the feedback stabilization method is demonstrated by comparing the measurements of EXAFS spectra on inhomogeneous diluted Ti‐containing samples with and without feedback applied.     

Time‐resolved investigation of the ν1 ro‐vibrational Raman band of H2CO with fs‐CARS

The technique of femtosecond time‐resolved coherent anti‐Stokes scattering (fs‐CARS) is used to investigate the strongly perturbed ν₁ ro‐vibrational Raman band of formaldehyde (H₂CO). The time‐dependent signal is simulated using a ‘Watson‐’Hamiltonian in A‐type reduction and Raman theory for asymmetric rotors. The results are compared with the experimental data. The fs‐CARS method measures the evolution of the polarization in a molecular ensemble via superposition of many states and is sensitive to spectral irregularities or line shifts of the involved transitions. ‘Coriolis’ interactions play a major role in the analysis of the ν₁ band of formaldehyde. We successfully simulate the fs‐CARS transient signal from the ν₁ band of formaldehyde including a model for multiple ‘Coriolis’ interactions, without the necessity of describing the complete interaction between all the vibrational levels. ‘Coriolis’ coupling coefficients and energy shifts are derived from the experiment by a least‐square fit. The results are discussed and compared to literature values. Copyright © 2006 John Wiley & Sons, Ltd.     

Time‐resolved resonance Raman and density functional theory study of the photochemistry of 4‐benzoylpyridine in acetonitrile and 2‐propanol

A nanosecond time‐resolved resonance Raman (ns‐TR³) spectroscopic investigation of the intermolecular hydrogen‐abstraction reaction of the triplet state of 4‐benzoylpyridine (4‐BPy) in 2‐propanol solvent is reported. The TR³ results reveal a rapid hydrogen abstraction (<10 ns) by the 4‐BPy triplet state (nπ*) with the 2‐propanol solvent, leading to formation of a 4‐BPy ketyl radical and an associated dimethyl ketyl radical partner from the solvent. The recombination of these two radical species occurs with a time constant about 200 ns to produce a para‐N‐LAT (light absorbing transient). The structure, major spectral features, and identification of the ketyl radical and the para‐N‐LAT coupling complex have been determined and confirmed by comparison of the TR³ results with results from density functional theory (DFT) calculations. A reaction pathway for the photolysis of 4‐BPy in 2‐propanol deduced from the TR³ results is also presented. The electron‐withdrawing effect of the heterocyclic nitrogen for 4‐BPy on the triplet state makes it have a significantly higher chemical reactivity for the hydrogen abstraction with 2‐propanol compared to the previously reported corresponding benzophenone triplet reaction under similar reaction conditions. In addition, the 4‐BPy ketyl radical reacts with the dimethyl ketyl radical to attach at the para‐N atom position of the pyridine ring to form a cross‐coupling product such as 2‐[4‐(hydroxy‐phenyl‐methylene)‐4h‐pyridin‐1‐yl]‐propan‐2‐ol instead of attacking at the para‐C atom position as was observed for the corresponding benzophenone reaction reported in an earlier study. Copyright © 2008 John Wiley & Sons, Ltd.     

Implementation of ultrafast X‐ray diffraction at the 1W2B wiggler beamline of Beijing Synchrotron Radiation Facility

The implementation of a laser pump/X‐ray probe scheme for performing picosecond‐resolution X‐ray diffraction at the 1W2B wiggler beamline at Beijing Synchrotron Radiation Facility is reported. With the hybrid fill pattern in top‐up mode, a pixel array X‐ray detector was optimized to gate out the signal from the singlet bunch with interval 85 ns from the bunch train. The singlet pulse intensity is ～2.5 × 10⁶ photons pulse^?1 at 10 keV. The laser pulse is synchronized to this singlet bunch at a 1 kHz repetition rate. A polycapillary X‐ray lens was used for secondary focusing to obtain a 72 µm (FWHM) X‐ray spot. Transient photo‐induced strain in BiFeO₃ film was observed at a ～150 ps time resolution for demonstration.     

Combination of LFP‐TRIR spectroscopy and DFT computation as a tool to determine the intermediate during the photooxidation of triarylphosphine

Laser flash photolysis‐time‐resolved infrared spectroscopy (LFP‐TRIR) was performed on an acetonitrile or dichloromethane solution of triarylphosphines, Ar₃P, in air. A transient spectrum consisting of several absorption bands appeared in the region of 1050–1300 cm^?1 on the TRIR on a microsecond timescale, which disappeared on a millisecond timescale. To identify the observed transient intermediate, the IR spectra of possible intermediates of the photoreaction were simulated by theoretical calculations based on density functional theory (DFT). The IR spectrum simulated for the phosphine peroxidic radical cation, Ar₃P⁺OO^?, well predicted the observed IR spectrum, showing that Ar₃P⁺OO^? is formed as a transient intermediate upon the LFP of Ar₃P in air. Copyright © 2014 John Wiley & Sons, Ltd.     

In situ observation of Ni–Mo–S phase formed on NiMo/Al2O3 catalyst sulfided at high pressure by means of Ni and Mo K‐edge EXAFS spectroscopy

To obtain direct evidence of the formation of the Ni–Mo–S phase on NiMo/Al₂O₃ catalysts under high‐pressure hydrodesulfurization conditions, a high‐pressure EXAFS chamber has been constructed and used to investigate the coordination structure of Ni and Mo species on the catalysts sulfided at high pressure. The high‐pressure chamber was designed to have a low dead volume and was equipped with polybenzimidazole X‐ray windows. Ni K‐edge k³χ(k) spectra with high signal‐to‐noise ratio were obtained using this high‐pressure chamber for the NiMo/Al₂O₃ catalyst sulfided at 613 K and 1.1 MPa over a wide k range (39.5–146 nm^?1). The formation of Ni–Mo and Mo–Ni coordination shells was successfully proved by Ni and Mo K‐edge EXAFS measurement using this chamber. Interatomic distances of these coordination shells were almost identical to those calculated from Ni K‐edge EXAFS of NiMo/C catalysts sulfided at atmospheric pressure. These results support the hypothesis that the Ni–Mo–S phase is formed on the Al₂O₃‐supported NiMo catalyst sulfided under high‐pressure hydrodesulfurization conditions.     

Using a standard sample to estimate the X‐ray wavelength of the 1W2A SAXS beamline at BSRF

This contribution describes a method for measuring diffraction peaks of a standard sample to estimate the incident X‐ray wavelength at the 1W2A SAXS beamline at BSRF. A simple simulation has been performed to establish the factors influencing the accuracy of the wavelength measurement. Appropriate measurement conditions and error control measures are presented. An actual experimental example further verifies the effectiveness of the simulation. This method is particularly suitable for synchrotron radiation beamlines using bent triangular crystal monochromators.