非负载型铁催化剂上二氧化碳加氢制低碳烯烃

研究了非负载型铁催化剂上CO₂加氢制低碳烯烃反应.结果显示,添加碱金属可显著提高铁催化剂上的CO₂转化率和烯烃选择性.在经K和Rb修饰的Fe催化剂上,CO₂转化率可达约40%,烯烃选择性达到50%以上,其中C₂~C₄烯烃收率超过10%.催化剂表征结果表明,碱金属促进了催化剂中碳化铁的生成,这可能是催化剂性能提高的一个关键原因.随着K含量由1 wt%增加至5 wt%,CO₂转化率及烯烃选择性均升高.但K含量过高时,催化剂活性降低.这可能是由于催化剂比表面积和CO₂化学吸附量降低所致.当K含量为5%~10%时,K-Fe催化剂上烯烃收率较高; 进一步添加适量的硼可进一步提高烯烃选择性,且CO₂转化率下降不大.     

Zn4Si2O7(OH)2H2O盐修饰的纳米Ru催化剂催化苯选择加氢制环己烯

利用沉淀法制备了纳米Ru催化剂, 在ZnSO₄存在下考察了Na₂SiO₃·9H₂O和二乙醇胺作反应修饰剂对Ru催化剂催化苯选择加氢制环己烯性能的影响, 并用X-射线衍射(XRD)、X-射线荧光光谱(XRF)和透射电镜-能量散射谱(TEM-EDS)等物理化学手段对加氢前后Ru催化剂进行了表征。结果表明, 在水溶液中Na₂SiO₃与ZnSO₄可以反应生成Zn₄Si₂O₇(OH)₂H₂O盐、H₂SO₄和Na₂SO₄, 化学吸附在Ru催化剂表面上的Zn₄Si₂O₇(OH)₂H₂O盐起着提高Ru催化剂环己烯选择性的关键作用。Na₂SiO₃·9H₂O量的增加, 生成的Zn₄Si₂O₇(OH)₂H₂O盐逐渐增加, Ru催化剂的活性降低, 环己烯选择性逐渐升高。向反应体系中加入二乙醇胺, 它可以中和Na₂SiO₃与ZnSO₄反应生成的硫酸, 使化学平衡向生成更多的Zn₄Si₂O₇(OH)₂H₂O盐的方向移动, 导致Ru催化剂环己烯选择性增加。当Ru催化剂与ZnSO₄·7H₂O、Na₂SiO₃·9H₂O和二乙醇胺、分散剂ZrO₂的质量比为1.0:24.6:0.4:0.2:5.0时, 2 g Ru催化剂上苯转化73%时环己烯选择性和收率分别为75%和55%, 而且该催化剂体系具有良好的重复使用性和稳定性。     

Zn4Si2O7(OH)2H2O盐修饰的纳米Ru催化剂催化苯选择加氢制环己烯

利用沉淀法制备了纳米Ru催化剂,在ZnSO₄存在下考察了Na₂SiO₃·9H₂O和二乙醇胺作反应修饰剂对Ru催化剂催化苯选择加氢制环己烯性能的影响,并用X-射线衍射(XRD)、X-射线荧光光谱(XRF)和透射电镜-能量散射谱(TEM-EDS)等物理化学手段对加氢前后Ru催化剂进行了表征。结果表明,在水溶液中Na₂SiO₃与ZnSO₄可以反应生成Zn₄Si₂O₇(OH)₂H₂O盐、H₂SO₄和Na₂SO₄,化学吸附在Ru催化剂表面上的Zn₄Si₂O₇(OH)₂H₂O盐起着提高Ru催化剂环己烯选择性的关键作用。Na₂SiO₃·9H₂O量的增加,生成的Zn₄Si₂O₇(OH)₂H₂O盐逐渐增加,Ru催化剂的活性降低,环己烯选择性逐渐升高。向反应体系中加入二乙醇胺,它可以中和Na₂SiO₃与ZnSO₄反应生成的硫酸,使化学平衡向生成更多的Zn₄Si₂O₇(OH)₂H₂O盐的方向移动,导致Ru催化剂环己烯选择性增加。当Ru催化剂与ZnSO₄·7H₂O、Na₂SiO₃·9H₂O和二乙醇胺、分散剂ZrO₂的质量比为1.0:24.6:0.4:0.2:5.0时,2 g Ru催化剂上苯转化73%时环己烯选择性和收率分别为75%和55%,而且该催化剂体系具有良好的重复使用性和稳定性。     

大气压旋转螺旋状电极辉光放电等离子体催化甲烷偶联

采用新研制的具有旋转螺旋状电极的大气压辉光放电等离子体反应器催化甲烷偶联制碳二烃. 实验采用铜电极和不锈钢电极分别考察了输入电场峰值电压和甲烷、氢气进料流量等参数对甲烷转化率和碳二烃收率、选择性的影响. 在长时间连续反应无明显积碳的情况下, 最佳试验结果是电极材料为金属铜, 进料流量为60 mL•min^-1, V(CH₄ )/V(H₂)=1的条件下, 输入电场峰值电压为2.3 kV时, 甲烷转化率为70.64%, 碳二烃单程收率及其选择性分别为69.85%和 99.14%.     

HCl存在下CeO2基催化剂上乙烷氧化脱氢制乙烯

报道了一种HCl存在时温和条件下的乙烷氧化脱氢制乙烯催化转化新途径. 研究发现,在多种金属氧化物催化剂中,CeO₂呈现最佳乙烯生成的催化性能. 与纳米粒子相比,具有棒状和立方体状形貌的CeO₂纳米晶具有较高的乙烷转化率和乙烯选择性. 以MnO_x修饰CeO₂可进一步提高催化性能. 在8 wt% MnO_x-CeO₂催化剂上,723K反应2 h时乙烷转化率和乙烯选择性分别为94%和69%. 该催化剂性能稳定,反应100 h乙烯收率可保持在65%-70%. HCl的存在对乙烯的选择性生成起着至关重要的作用,一部分乙烯来自于氯乙烷的脱HCl反应.     

FeMn、FeMnNa和FeMnK催化剂上合成气制低碳烯烃的比较

研究了钠、钾助剂对FeMn 合成低碳烯烃催化剂结构及性能的影响. 低温N₂吸附、X射线光电子能谱（XPS）、X射线衍射（XRD）、H₂程序升温还原（H₂-TPR）、CO/CO₂程序升温脱附（CO/CO₂-TPD）、Mössbauer 谱和CO+H₂反应的研究结果表明,增加Mn助剂含量促进了活性相的分散和低碳烯烃的生成,而过多锰助剂在催化剂表面的富集则降低了费托合成反应的CO转化率;钾助剂和钠助剂的加入均抑制了催化剂的还原并且促进了CO₂和CO的吸附. 比较还原后（H₂/CO摩尔比为20）和反应后（H₂/CO摩尔比为3.5）催化剂的体相结构可以发现,在FeMn、FeMnNa和FeMnK催化剂中,由于钾助剂的碱性和CO吸附能力较强,因此体相中FeC_x的含量相对较高;而活性测试结果表明,FeMnNa催化剂拥有最好的CO转化率（96.2%）和低碳烯烃选择性（30.5%,摩尔分数）.     

Ce-Cu-Co/CNTs催化剂催化合成气制低碳醇及乙醇的研究

采用共浸渍法制备了不同Ce含量的Ce-Cu-Co/CNTs 催化剂, 考察了其在合成气制低碳醇反应中的催化性能, 借助X射线衍射(XRD)、程序升温还原(H₂-TPR)、N₂吸脱附实验(BET)、透射电镜(TEM)和CO程序升温脱附(CO-TPD)对这些催化剂进行了表征. 结果表明, 当Ce的质量分数为3%时, 低碳醇的时空收率和选择性达到最高, 分别为696.4 mg·g^-1·h^-1和59.7%, 其中乙醇占总醇的46.8%, 适量Ce的添加能提高Cu物种在催化剂上的分散度和催化剂的还原性能, 能显著地增加催化剂吸附CO的能力, 促进合成醇活性位的形成, 进而明显提高催化剂的活性和总醇的选择性. 研究表明, 将具有高活性和高碳链增长能力的CuCo基催化剂与碳纳米管的限域效应结合, 可实现缩窄产物分布、大幅度提高乙醇选择性的目的.     

常压辉光放电等离子体转化CH4制C2烃的研究

采用新型的旋转电极辉光放电反应器, 在常温常压下对辉光等离子体作用下的甲烷转化制C₂烃进行了研究. 在氢气共存条件下, 考察了反应器电极的结构、材料, 输入电场峰值电压和反应物流率等参数对甲烷转化率和C₂烃单程收率及其选择性的影响规律, 同时比较了不同反应器的能量效率. 结果表明: 在本实验条件下, 金属铜材料好于不锈钢, 螺旋形结构优于三排圆盘结构. CH₄转化率和C₂烃选择性和收率均随输入电场峰值电压的升高而增大, 随反应物流量的增加而减小. 从CH₄转化率、C₂烃的收率和选择性的指标来评价这些反应器, 采用旋转螺旋状铜电极反应器时最好, 当反应物流量为60 mL/min时, 甲烷最高转化率为77.31%, 对应的C₂烃收率和选择性分别为75.66%和97.88%; 当能量密度为800 kJ/mol时, 能效最高为13.5%.     

常压辉光放电等离子体转化CH4制C2烃的研究

采用新型的旋转电极辉光放电反应器, 在常温常压下对辉光等离子体作用下的甲烷转化制C₂烃进行了研究. 在氢气共存条件下, 考察了反应器电极的结构、材料, 输入电场峰值电压和反应物流率等参数对甲烷转化率和C₂烃单程收率及其选择性的影响规律, 同时比较了不同反应器的能量效率. 结果表明: 在本实验条件下, 金属铜材料好于不锈钢, 螺旋形结构优于三排圆盘结构. CH₄转化率和C₂烃选择性和收率均随输入电场峰值电压的升高而增大, 随反应物流量的增加而减小. 从CH₄转化率、C₂烃的收率和选择性的指标来评价这些反应器, 采用旋转螺旋状铜电极反应器时最好, 当反应物流量为60 mL/min时, 甲烷最高转化率为77.31%, 对应的C₂烃收率和选择性分别为75.66%和97.88%; 当能量密度为800 kJ/mol时, 能效最高为13.5%.     

Ni/CeO2-SiO2催化剂的制备、表征及其甲烷部分氧化制合成气性能

以硝酸亚铈（Ce（NO₃）₃·6H₂O）和正硅酸四乙酯（C₈H₂₀O₄Si）为前驱体,采用溶胶-凝胶法合成了系列具有大比表面积的xCeO₂-（1-x）SiO₂（x = 0,0.25,0.50,0.75,1）复合氧化物载体,然后浸渍活性组分Ni制得用于甲烷部分氧化制合成气的Ni催化剂。运用N₂物理吸附-脱附、X射线粉末衍射、扫描电镜、紫外-可见漫反射光谱、氢程序升温还原、氨程序升温脱附和热重等手段对所得催化剂的组织结构、还原性、表面酸性和积炭行为等进行了表征;同时考察了催化剂的组成、焙烧温度和反应时间等对催化剂在甲烷部分氧化制合成气中催化性能的影响。表征结果表明,该系列Ni/CeO₂-SiO₂催化剂具有大比表面积,CeO₂晶粒较小,NiO的分散性好且易被还原,表面酸性弱,不容易积炭。当Ce/Si摩尔比为1：1,活性组分Ni的质量分数为10%,焙烧温度为700℃时,所制备的Ni/CeO₂-SiO₂催化剂表现出较好的稳定性、最高的CH₄转化率（~84%）和对产物CO及H₂的选择性（>87%）。     

Direct and Highly Selective Conversion of Synthesis Gas into Lower Olefins: Design of a Bifunctional Catalyst Combining Methanol Synthesis and Carbon–Carbon Coupling

The direct synthesis of lower (C₂ to C₄) olefins, key building‐block chemicals, from syngas (H₂ /CO), which can be derived from various nonpetroleum carbon resources, is highly attractive, but the selectivity for lower olefins is low because of the limitation of the Anderson–Schulz–Flory distribution. We report that the coupling of methanol‐synthesis and methanol‐to‐olefins reactions with a bifunctional catalyst can realize the direct conversion of syngas to lower olefins with exceptionally high selectivity. We demonstrate that the choice of two active components and the integration manner of the components are crucial to lower olefin selectivity. The combination of a Zr–Zn binary oxide, which alone shows higher selectivity for methanol and dimethyl ether even at 673 K, and SAPO‐34 with decreased acidity offers around 70 % selectivity for C₂–C₄ olefins at about 10 % CO conversion. The micro‐ to nanoscale proximity of the components favors the lower olefin selectivity.     

Preparation and operating conditions for cobalt cerium oxide catalysts used in the conversion of synthesis gas into light olefins

Cobalt cerium oxides, prepared using a co-precipitation procedure, were studied as catalysts for the conversion of synthesis gas to light olefins (C₂-C₄). Specifically, we studied the effect of a range of preparation variables, including the molar ratio of the [Co]/[Ce] of the precipitation solution, ageing time and calcination temperature. In addition, the effects of supports and promoters on the catalysts’ activity and selectivity and a range of reaction temperatures using synthesis gas with different H₂/CO molar feed ratios were investigated. The catalyst containing a molar ratio of 80% Co and 20% Ce, aged for 2 h, supported with 15 wt% SiO₂ without any promoter, at an operating temperature of 450 °C and an H₂/CO feed ratio of 2/1 (GHSV = 4500 h^?1), performed optimally for the conversion of synthesis gas to light olefins. The characterization of both the precursors and the calcined catalysts by powder X-ray diffraction, scanning electron microscopy, Brunauer-Emmett-Teller specific surface area measurements and thermal analysis methods, including TGA and DSC, show that all the preparation variables influenced the catalyst precursor structure.     

Effects of type of contact between Co/SiO2 and Pd/b on the direct synthesis of isoparaffins from synthesis gas

The effect of addition of Pd/b on the Co/SiO₂ catalyst was studied for F-T reaction. Pd/b could enhance the formation of C₄-C₉ isoparaffins while the Co/SiO₂ catalyst alone gave the products with wide carbon numbers distribution. The reason is the olefins and long-chain normal paraffins from F-T reaction on Co/SiO₂ catalyst form light hydrocarbons containing isoparaffins through the hydrocracking and hydroisomerization on Pd/b. For Co/SiO₂+Pd/b catalyst, the selectivity to isoparaffins depends on the contact conditions. The granular hybrid catalyst is much more selective for isomerization than the powder hybrid catalyst, while the selectivity to CH₄, n-paraffins and olefins is lower than that on the powder hybrid catalyst. This revised version was published online in August 2006 with corrections to the Cover Date.     

Hydrogenation promoting effect of iron on the catalytic properties of zirconium dioxide in the reaction of formation of light olefins from CO and H2

Iron admixtures (0.1 %) raise the activity of zirconium dioxide catalyst in regard to the formation of C₂-C₄ olefins from CO and H₂. Manifestation of the promoting effect in the synthesis of isobutylene (in contrast to C₂-C₃ olefins) requires close contact between the metal and ZrO₂. Iron promoted zirconium dioxide is more selective for olefins than is ZrO₂ with nickel admixtures.Translated from Teoreticheskaya i Éksperimental'naya Khimiya, Vol. 32, No. 6, pp. 367–371, November December, 1996.     

CO Hydrogenation by K-Promoted Coprecipitated Co/Al2O3

Effect of K promotion on the CO hydrogenation activity and selectivity of coprecipitated Co/Al₂O₃ has been studied. K addition is found to lower total activity while enhancing C₂-C₄ olefins selectivity; kinetic data indicate that the reaction mechanism is not affected.     

The synthesis and reactions of cationic rhodium and iridium complexes; evidence for hydrogen-transfer processes

Reactions of rhodium(I) and iridium(I) chlorocomplexes of cyclohexa-1,3-diene, cyclohepta-1,3-diene, and cylo-octa-1,3,5-triene with AgBF₄/CH₂Cl₂ afford respectively the cations [M(C₆H₆)(1,3-C₆H₈)]⁺, [M(η⁵-C₇H₇)(η⁵C₇H₉)]⁺ and [M(η⁶-C₈H₁₀)(η⁴-C₈H₁₀)]⁺; the latter complex is a hydrogenation catalyst for olefins.     

Effect of doping with small amounts of nickel on the catalytic properties of zirconium dioxide in the hydrogenation of carbon monoxide

Doping of zirconium dioxide with small amounts of nickel (0. 03 %) caused a several fold increase in the rate of formation of C₂-C₄ olefins, particularly isobutene, from CO and hydrogen. The combined catalyst ZrO₂-Ni/SiO₂ showed increased selectivity with respect to olefins in comparison with the Ni/SiO₂ catalyst.Science Prosp., 31. Translated from Teoreticheskiya i Éksperimental'naya Khimiya, Vol. 32, No. 6, 353–357, November-December, 1996. Original article submitted March 1, 1996.     

Effect of Treatment with Carbon Dioxide of the Zn Form of the TsVK Zeolite on Its Acid and Catalytic Properties in the Conversion of Methanol to Hydrocarbons

It is shown that it is possible to increase the yield of liquid hydrocarbons of the benzene fraction in the Mobil process by use of a catalyst modified by treatment with CO₂ of the Zn form of the TsVK zeolite. It is established that on treatment with CO₂ of the Zn-TzVK zeolite the concentration of strongly acidic -centers is increased. As a result of alkylation of C₂-C₄ olefins by methanol at these sites more of the high molecular C₅-C₈ aliphatic hydrocarbons are formed. Selectivity of conversion of methanol to liquid C₅-C₁₀ hydrocarbons of the benzene fraction is increased, but selectivity with respect to the light C₂-C₄ fractions is decreased.     

A new process for preparing dialdehyde by catalytic oxidation of cyclic olefins with aqueous hydrogen peroxide

A. novel peroxo-niobophosphate was synthesized for the first time and used as a catalyst in the oxidation reaction of cyclic olefins with aqueous hydrogen peroxide to prepare dialdehy-des. The catalyst was characterized by elemental analysis, thermographic analyses, IR, UV/vis, 31P NMR and XPS spectra as [ π-C5H5N(CH2 )13 CH3 ]2 [ Nb4O6 (O2 )2 (PO4 )2 ] ·6H2O (PTNP). It showed high selectivity to glutaraldehyde in the catalytic oxidation of cyclopentene with aqueous hydrogen peroxide in ethanol.