The chemistry of uranium. Part XXIX. The kinetics of the thermal decomposition of (NMe4)2U(NO3)6

The thermal decomposition of (NMe₄)₂U(NO₃)₆ was studied in a dynamic nitrogen atmosphere. Isothermal kinetic studies indicated that the overall reaction consists of two consecutive reactions. The enthalpy of decomposition of the overall reaction was found to be 55 kJ mole^?1.     

The thermal decomposition reactions of [Co(en)3](NO3)3 and [Co(en)3](HSO4)3

The thermal decomposition reactions were determined for [Co(en)₃](N0₃)₃ and [Co(en)₃(HSO₄)₃ in a dynamic nitrogen gas atmosphere and _vacuo, where en represents ethylenediamine. Data were obtained using thermogravimetry, DTA, thermomagnetic analysis, and mass spectrometry. The dissociation reactions in nitrogen were found to be as follows:

and

In vacuo, the dissociation process for [Co(en)₃](N0₃)₃ is the same as in nitrogen. Also, the decomposition of [Co(en)₃](HSO₄)₃ is the same except for the first step which is:

     

Non-equivalent water molecules in [Ni(H2O)6](ClO4)2 and in [Ni(D2O)6](ClO4)2 in the thermogravimetric investigations

The thermal decomposition of [Ni(H₂O)₆](ClO₄)₂ and [Ni(D₂O)₆](ClO₄)₂ were studied by thermogravimetric analysis (TG) and simultaneous differential thermal analysis (SDTA) at a constant heating rate. The gaseous products of the decomposition were on-line identified by a quadrupole mass spectrometer (QMS). In both cases the process of decomposition starts at ca. 410 K and is connected with removal of water molecules in a stepwise way; at the beginning the first water molecule is lost, then the second and at higher temperature the third one. The rest of the water molecules are lost in the temperature region of ClO₄⁻ decomposition. The energy of activation of the process was calculated in both cases.     

Thermal decomposition of [Co(NH3)6]2(C2O4)3·4H2O: II. Identification of the gaseous products

The main goal of the presented work was to verify the previously assumed decomposition stages of [Co(NH₃)₆]₂(C₂O₄)₃·4H₂O (HACOT) [Thermochim. Acta 354 (2000) 45] under different atmospheres (inert, oxidising and reducing). The gaseous products of the decomposition were qualitatively and quantitatively analysed by mass spectrometry (MS) and Fourier-transformed infrared spectroscopy (FT-IR). It was confirmed that the gaseous products of HACOT decomposition under studied atmospheres there were H₂O (stage I) and NH₃, CO₂ (stage II). The main gaseous products in the third stage in argon and hydrogen (20 vol.% H₂/Ar) were CO and CO₂, whereas in air (20 vol.% O₂/Ar) only CO₂ was identified. Under the oxidising as well as reducing atmospheres the influence of secondary reactions on the composition of both, solid and gaseous products was found particularly strong during the third stage of the process. The studies of the multistage decomposition of HACOT, additionally complicated by many secondary reactions, required application of the hyphenated TA-MS or TA-FT-IR techniques combined with the pulse thermal analysis PTA^® allowing quantification of the spectroscopic signals and investigation of gas-solid and gas-gas reactions in situ.     

Photochemistry of (η5)-C5H5)Mn(CO)2[C(C6H5)2]. Generation of the diphenylcarbene radical anion

The electronic absorption spectrum of (η⁵-C₅H₅)Mn(CO)₂[C(C₆H₅)₂]shows an intense maximum which is assigned to a MLCT transition in which the empty p_π orbital on the carbene carbon is populated. Upon irradiation of this band, the complex undergoes a decomposition with a disappearance quantum yield Φ = 0.10 ± 0.01 independent of solvent. In the CT excited state, the complex can be roughly described as containing d⁵ Mn^II and a diphenylcarbene radical anion ligand C(C₆H₅)₂^?. Due to the kinetic lability, the complex decomposes producing a Mn^II species and the free carbene radical anion, which then undergoes secondary reactions. In addition, small amounts of substitution product are observed. It is proposed that prior to total decomposition of the excited state, a radical pair (η⁵-C₅H₅)Mn(CO)₂S⁺/C(C₆H₅)₂^?forms (S = solvent). A back electron transfer from C(C₆H₅)₂^?to the labile cation competes with decomposition to produce the substituted complex and free carbene.     

Solvothermal synthesis of three new dimeric thiogermanates (enH)4Ge2S6, [Mn(en)3]2Ge2S6 and [Ni(en)3]2Ge2S6 from germanium dioxide and sulfur powder

Three new thiogermanates (enH)₄Ge₂S₆ (1) and [M(en)₃]₂Ge₂S₆ (M=Mn (2), Ni (3); en=ethylenediamine) were synthesized using GeO₂ and S₈ as starting materials in molar ratio of 1:0.5 under solvothermal conditions. These compounds suggest that the dimeric [Ge₂S₆]⁴⁻ anion is likely to be the main germanium-containing species in en system and it also might be preferred as counter anions by the transition metal complex cations in crystallization. The cations of [Mn(en)₃]²⁺ and [Ni(en)₃]²⁺ are even better mineralizers than the protonated amine of [enH]⁺. The crystal systems of [Ge₂S₆]⁴⁻ compounds are related to entities of cations and intermolecular reactions between cations and [Ge₂S₆]⁴⁻ anions. The compounds remove ethylenediamine and H₂S molecules in multi steps when being heated under nitrogen stream.     

Low-temperature heat capacity and standard enthalpy of formation of neodymium glycine perchlorate complex [Nd2(Gly)6(H2O)4](ClO4)6·5H2O

Rare-earth perchlorate complex coordinated with glycine [Nd₂(Gly)₆(H₂O)₄](ClO₄)₆·5H₂O was synthesized and its structure was characterized by using thermogravimetric analysis (TG), differential thermal analysis (DTA), chemical analysis and elementary analysis. Its purity was 99.90%. Heat capacity measurement was carried out with a high-precision fully-automatic adiabatic calorimeter over the temperature range from 78 to 369 K. A solid-solid phase transformation peak was observed at 256.97 K, with the enthalpy and entropy of the phase transformation process are 4.438 kJ mol⁻¹ and 17.270 J K⁻¹ mol⁻¹, respectively. There is a big dehydrated peak appears at 330 K, its decomposition temperature, decomposition enthalpy and entropy are 320.606 K, 41.364 kJ mol⁻¹ and 129.018 J K⁻¹ mol⁻¹, respectively. The polynomial equations of heat capacity of this compound in different temperature ranges have been fitted. The standard enthalpy of formation was determined to be −8023.002 kJ mol⁻¹ with isoperibol reaction calorimeter at 298.15 K.     

The effect of Co2(CO)8 on the decomposition of CoH(CO)4

The thermal decomposition of CoH(CO)₄ in solution to Co₂(CO)₈ and H₂ is catalyzed by Co₂(CO)₈; the effect of the latter is proportional to the square root of the concentration. Probably the Co(CO)₄· radical is involved in the process. One-electron reactions of the trityl radical with CoH(CO)₄ and benzophenone ketyl with Co₂(CO)₈ are discribed.     

[Gd2(Gly)6(H2O)4](ClO4)6(H2O)5的合成、晶体结构与热化学研究

利用微波技术合成了配合物[Gd₂(Gly)₆(H₂O)₄](ClO₄)₆(H₂O)₅, 进行了化学成分分析、红外表征和热重分析. 应用X衍射仪测定其晶体结构, 该晶体为一维链结构, 属三斜晶系, P 空间群, 晶胞参数: a＝1.1569(17) nm, b＝1.4138(2) nm, c＝1.5642(2) nm, α＝96.910(2)°, β＝102.735(2)°, γ＝105.512(2)°, V＝2.3606(6) nm³, Z＝2, D_c＝2.144 g•cm^－3. 采用精密溶解-反应量热计, 通过设计热化学循环, 计算出了该配合物的标准摩尔生成焓为 －(7960.73±3.23) kJ•mol^－1.     

The thermal decomposition of K2Pt(CN)4Br2 and K2Pt(CN)4

The thermal decomposition of K₂Pt(CN)₄Br₂ was studied by thermogravimetry, evolved gas analysis, X-ray diffraction and infrared spectroscopy. The reduction of the platinum occurs in several steps, each evolving cyanogen. The first step corresponded to the formation of a complex of apparently Pt(III) with bridging cyanide ions. The second and third steps which form Pt(II) with primarily terminal cyanide ions and finally the metal, are not well resolved. K₂Pt(CN)₄-8H₂O first lost water of hydration and then a single molecule of cyanogen corresponding to the formation of platinum metal and KCN.     

Synthesis,Characterization, and DNA Binding Properties of Dinuclear Copper（Ⅱ） Complex [Cu2（TATP）2（L-Leu）2（CIO4）2]2·2H2O

A dinuclear copper（Ⅱ） complex[Cu2（TATP）2（L-Leu）2（CIO4）2]2·2H2Owas synthesized and characterized, where, TATP=1,4,8,9-tetraazatriphenylene, and L-Leu=L-leucinate. The complex was crystallized in the triclinic space group P1, with two independent molecules in a unit cell. Two Cu（Ⅱ） ions in each complex [Cu2（TATP）2（L-Leu）2（CIO4）2] molecule were found to be in different coordination geometries, i.e., Cu2 or Cu4 of a distorted square-pyramidal geometry coordinated with two nitrogens of TATP, the amino nitrogen and one carboxylate oxygen of L-Leu and one oxygen of perchlorate, and Cul or Cu3 with an octahedral geometry coordinated with the above stated similar coordinated atoms, and another carboxylate oxygen of L-Leu coordinating to Cu2 or Cu4. The complex can interact with CT-DNA by an intercalative mode and cleave pBR322 DNA in the presence of ascorbate.     

Crystal structure and single crystal EPR of (NH4)2(15-crown-5)3[Cu(mnt)2] and (NH4)2(benzo-15-crown-5)4[Cu(mnt)2]·0.5H2O

The X-ray crystal structures of (NH4)2(15-crown-5)3[Cu(mnt)2] (1) and (NH4)2(benzo-15-crown-5)4- [Cu(mnt)2]·0.5H2O (2) were determined. Two single crystals are composed of distinct structures of ammonium-crown ether supramolecular cation and [Cu(mnt)2]2- anion. The triple-decker dication in complex 1 and a sandwich dimmer in complex 2 were observed. X-Band EPR studies on the single crystals of both complex 1 and complex 2 have been carried out at room temperature, which revealed that complex 2 showed a perfect hyperfine structure of Cu whereas that of complex 1 could not be observed. The principal values and direction cosines of the principal axes of the g and A tensors were computed by a least-squares fitting procedure. The spin density of Cu(Ⅱ) was estimated according to the principal values of the A tensors and compared well with the results calculated based on DFT method.     

Synthesis, molecular structure, and catalytic activity of borohydride complexes [(Me3Si)2NC(NPri)2]2Nd(BH4)2Li(thf)2 and [(Me3Si)2NC(NPri)2]2Sm(BH4)2Li(thf)2

The reactions of lanthanide tris(borohydrides) Ln(BH₄)₃(thf)₃ (Ln = Sm or Nd) with 2 equiv. of lithium N,N′-diisopropyl-N′-bis(trimethylsilyl)guanidinate in toluene produced the [(Me₃Si)₂NC(NPrⁱ)₂]Ln(BH₄)₂Li(thf)₂ complexes (Ln = Sm or Nd), which were isolated in 57 and 42% yields, respectively, by recrystallization from hexane. X-ray diffraction experiments and NMR and IR spectroscopic studies demonstrated that the reactions afford monomeric ate complexes, in which the lanthanide and lithium atoms are linked to each other by two bridging borohydride groups. The complexes exhibit catalytic activity in polymerization of methyl methacrylate. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 3, pp. 441–445, March, 2007.     

Structure and properties of double complex salts [Co(NH3)6][Fe(CN)6] and [Co(NH3)6]2[Cu(C2O4)2]3

Double complex salts (DCSs) [Co(NH₃)₆][Fe(CN)₆] (I) and [Co(NH₃)₆]₂[Cu(C₂O₄)₂]₃ (II) and complex [Co(NH₃)₆]₂(C₂O₄)₃·4H₂O (III) are synthesized and investigated by single crystal XRD, crystal optics, and elemental analysis. The crystalline phases of I, II, and III (R-3, P2₁/c, and Pnnm space groups respectively) have the following crystallographic characteristics: a = 10.9804(2) ?, b = 10.9804(2) ?, c = 10.8224(3) ?, V = 1130.03(4) ?³, Z = 3, d _x = 1.65 g/cm³ (I); a = 9.6370(2) ?, b = 10.2452(2) ?, c = 13.2108(3) ?, V = 1932.90(9) ?³, Z = 2, d _x= 1.97 g/cm³ (II), and a = 11.7658(3) ?, b = 11.7254(3) ?, c = 14.1913(4) ?, V = 1304.34(5) ?³, Z = 2, d _x = 1.68 g/cm³ (III). This paper investigates the products of DCS thermolysis in a hydrogen atmosphere: the intermetallic compound CoFe with the bcc parameter a = 2.852 ? for I and a heterogeneous mixture of Co and Cu in the decomposition of II. The coordinated CN⁻ and C₂O₄²⁻ groups then turn into NH₃, hydrocarbons, and CO₂. The dominant hydrocarbon is methane.     

New Selenidogermanates with Transition-Metal Complexes as Counterions: Solvothermal Synthesis, Crystal Structures, and Properties of [Mn(en)3]2Ge2Se6 and [Fe(dien)2]2Ge2Se6

Summary. New selenidogermanates [Mn(en)₃]₂Ge₂Se₆ (en = ethylenediamine) and [Fe(dien)₂]₂Ge₂Se₆ (dien= diethylenetriamine) were synthesized by the reaction of germanium dioxide, elemental selenium, and transition metal chlorides in respectively en and dien. Both compounds crystallize in the monoclinic space group P2₁/n with two formula units in the unit cell, and consist of discrete [Ge₂Se₆]⁴⁻ anions with transition metal complex cations as counter ions. The [Ge₂Se₆]⁴⁻ anion is formed by two GeSe₄ tetrahedra sharing a common edge to form a planar Ge₂Se₂ four-membered ring. The [Mn(en)₃]²⁺ and [Ni(dien)₂]²⁺ complex cations are in distorted octahedral geometry. In both selenidogermanates extensive N–H···Se hydrogen bonding contacts lead to 3-dimensional network structures. The band gaps of 2.36 and 2.25 eV were derived from optical absorption spectra. Thermogravimetric analysis shows that the first compound decomposes in two steps under the nitrogen stream, while the second exhibits a one-step decomposition process.     

Isomorphism in the (NH4)2Th(NO3)6-K2Th(NO3)6-Rb2Th(NO3)6 system

Syntheses were developed, and compounds of composition (NH₄)_2x K_2y Rb_2z Th(NO₃)₆(x + y + z = 1) were prepared. These compounds were structurally studied using X-ray diffraction and IR spectroscopy. Incomplete miscibility in the solid phase of the title system was found, and the impossibility of existence of a hexanitratothorate complex in the (NH₄)₂Th(NO₃)₆-K₂Th(NO₃)₆ system at 298.15 K and the component molar ratio 1: 3 was demonstrated. Calorimetric standard enthalpies of formation and mixing at 298.15 K were determined. Original Russian Text ? N.G. Chernorukov, A.V. Knyazev, A.A. Sazonov, 2009, published in Zhurnal Neorganicheskoi Khimii, 2009, Vol. 54, No. 7, pp. 1066–1071.     

Thermal decomposition of the layered double hydroxides of formula Cu6Al2(OH)16CO3 and Zn6Al2(OH)16CO3

Zn-Al hydrotalcites and Cu-Al hydrotalcites were synthesised by coprecipitation method and analysed by X-ray diffraction (XRD) and thermal analysis coupled with mass spectroscopy. These methods provide a measure of the thermal stability of the hydrotalcite. The XRD patterns demonstrate similar patterns to that of the reference patterns but present impurities attributed to Zn(OH)₂ and Cu(OH)₂. The analysis shows that the d003 peak for the Zn-Al hydrotalcite gives a spacing in the interlayer of 7.59 ? and the estimation of the particle size by using the Debye-Scherrer equation and the width of the d003 peak is 590 ?. In the case of the Cu-Al hydrotalcite, the d003 spacing is 7.57 ? and the size of the diffracting particles was determined to be 225 ?. The thermal decomposition steps can be broken down into 4 sections for both of these hydrotalcites. The first step decomposition below 100°C is caused by the dehydration of some water absorbed. The second stage shows two major steps attributed to the dehydroxylation of the hydrotalcite. In the next stage, the gas CO₂ is liberated over a temperature range of 150°C. The last reactions occur over 400°C and involved CO₂ evolution in the decomposition of the compounds produced during the dehydroxylation of the hydrotalcite.     

Preparation of dinitrogen complexes Mo(N2)2P4 stabilised by phosphonite PPh(OEt)2 and phosphinite PPh2(OEt) ligands

Dinitrogen complexes Mo(N₂)₂P₄1, 2 [P=PPh(OEt)₂ and PPh₂OEt] were prepared by allowing a MoCl₃(THF)₃ solution containing an excess of phosphine to react with magnesium under nitrogen. Substitution reactions with CO and p-tolylisocyanide were studied, and led to Mo(CO)₂P₄, Mo(CO)₃P₃, and Mo(p-tolylNC)₂P₄ derivatives. Treatment of dinitrogen compound Mo(N₂)₂[PPh(OEt)₂]₄ with an excess of HCl gave the hydrazido(2-) [MoCl(NNH₂){PPh(OEt)₂}₄]Cl derivative. Reduction reactions with zinc amalgam of complexes 1 and 2 in the presence of lutidine·HCl gave ammonia in about 8-10% yield.     

Thermal behaviour of (NH4)3VO2F4 and Na(NH4)2VO2F4

The thermal behaviour of (NH₄)₃VO₂F₄ and Na(NH₄)₂VO₂F₄ was investigated using TG, DTA and DSC techniques. The occurrence of a first order phase transition with the onset of decomposition in both the compounds is confirmed. The temperature, energetics and hysteresis of the transition are obtained. A possible path for the thermal degradation is given for both the compounds, and the residues are identified.     

A new three-dimensional cobalt phosphate: Co5(OH2)4(HPO4)2(PO4)2

A three-dimensional (3D) cobalt phosphate: Co₅(OH₂)₄(HPO₄)₂(PO₄)₂ (1), has been synthesized by hydrothermal reaction and characterized by single-crystal X-ray diffraction, thermogravimetric analysis, and magnetic techniques. The title compound is a template free cobalt phosphate. Compound 1 exhibits a complex net architecture based on edge- and corner-sharing of CoO₆ and PO₄ polyhedra. The magnetic susceptibility measurements indicated that the title compound obeys Curie-Weiss behavior down to a temperature of 17 K at which an antiferromagnetic phase transition occurs.