Direct electrochemistry of glucose oxidase on sulfonated graphene/gold nanoparticle hybrid and its application to glucose biosensing

Sulfonated graphene nanosheet/gold nanoparticle (SGN/Au) hybrid was synthesized by electrostatic self-assembly of anionic SGN and positively charged gold nanoparticles. Due to the well-dispersivity of SGN in aqueous solution and its adequate negative charge, Au nanoparticles were assembled uniformly on graphene surface with high distribution. With the advantages of both graphene and Au nanoparticles, SGN/Au hybrid showed enhanced electrocatalytic activity towards O₂ reduction. Furthermore, it provided a conductive and favorable microenvironment for the glucose oxidase (GOD) immobilization and thus promoted its direct electron transfer at the glassy carbon electrode. Based on the consumption of O₂ caused by glucose at the interface of GOD electrode modified with SGN/Au hybrid, the modified electrode displayed satisfactory analytical performance, including high sensitivity (14.55 μA mM^?1 cm^?2), low detection limit (0.2 mM), an acceptable linear range from 2 to 16 mM, and also the prevention from the interference of some species. These results indicated that the prepared SGN/Au hybrid is a promising candidate material for high-performance glucose biosensor.     

Enhanced electrochemiluminescence of luminol at the gold nanoparticle/carbon nanotube/electropolymerised molecular imprinting composite membrane interface for selective recognition of triazophos

This paper reports a surface molecular self-assembly strategy for imprinting triazophos in the electropolymerised poly(aminthiophenol) (PATP) membranes at the surface of gold nanoparticle (AuNP)/carbon nanotube (CNT) composites modified glassy (GC) electrode for electrochemiluminescent (ECL) detection of pesticide triazophos. The electrochemical and ECL behaviours of luminol at the imprinted PATP/AuNP/CNT/GC electrode were investigated before and after the rebinding of triazophos. It was also found that the ECL intensity was strikingly enhanced by the adsorbed triazophos molecules in the imprinted PATP/AuNP/CNT composite membranes, which was about 5.2-fold as compared with the blank ECL intensity. On this basis, the molecularly imprinted polymer (MIP)-ECL sensor is established for high sensitive and selective detection of triazophos residues in vegetable samples. The resulting MIP-ECL sensor shows wide linear ranges from 3.1 × 10^?8 to 3.1 × 10^?5 g L^?1 with lower detection limit of 3.1 × 10^?9 g L^?1 for triazophos. Moreover, the MIP-ECL sensor has the advantages of high sensitivity, speed, specificity, stability and can become a promising technique for organophosphate pesticide detection.     

Highly selective determination of ascorbic acid,epinephrine, and uric acid by differential pulse voltammetry using poly(Adizol Black B)-modified glassy carbon electrode

A polymerized film of Adizol Black B (ABB) on the surface of glassy carbon (GC) electrode was prepared for the simultaneous determination of ascorbic acid (AA), epinephrine (EP), and uric acid (UA). This new electrode presented an excellent electrocatalytic activity towards the oxidation of AA, EP, and UA by differential pulse voltammetry method. The oxidation peaks of the three compounds were well defined and had the enhanced peak currents. The separation of the oxidation peak potentials for AA–EP and EP–UA were about 180 and 130 mV, respectively. The calibration curves obtained for AA, EP, and UA were in the ranges of 2.0–1,970.0, 0.1–64.0, and 0.1–1,700.0 μmol L^–1, respectively. The detection limits (S/N?=?3) were 0.01, 0.007, and 0.02 μmol L^–1 for AA, EP, and UA, respectively. The diffusion coefficient and the catalytic rate constant for the oxidation reaction of EP at poly(ABB) film-coated GC electrode were calculated as 1.54(±0.10)?×?10^?4 cm² s^?1 and 4.5?×?10³ mol^?1 L s^?1, respectively. The present method was applied to the determination of EP in pharmaceutical, AA in commercially available vitamin C tablet, and UA in urine samples.     

Determination of Ascorbic Acid in the Presence of Uric Acid and Folic Acid by a Nanostructured Electrochemical Sensor Based on a TiO2 Nanoparticle Carbon Paste Electrode

A carbon paste electrode (CPE), modified with novel hydroquinone/TiO₂ nanoparticles, was designed and used for simultaneous determination of ascorbic acid (AA), uric acid (UA) and folic acid (FA). The magnitude of the peak current for modified TiO₂-nanoparticle CPE (MTNCPE) increased sharply in the presence of ascorbic acid and was proportional to its concentration. A dynamic range of 1.0–1400.0 μM, with the detection limit of 6.4 × 10^?7 M for AA, was obtained using the DPV technique (pH = 7.0). The prepared electrode was successfully applied for the determination of AA, UA, and FA in real samples.     

Electrochemical determination of methyl parathion at a Pd/MWCNTs-modified electrode

Palladium nanoparticles supported on MWCNTs (Pd/MWCNTs) were successfully prepared by a simple ethylene glycol reduction method in an oil bath. An electrochemical sensor based on Pd/MWCNTs nanocomposite-modified glassy carbon electrode was fabricated for the determination of methyl parathion by differential pulse voltammetry measurement. A highly linear response to methyl parathion in the concentration ranging from 0.10 μg mL^?1 to 14 μg mL^?1 was observed, and a detection limit of 0.05 μg mL^?1 was obtained with the calculation based on signal/noise?=?3. The present work provides a simple and rapid approach to the detection of methyl parathion.     

Anodic Stripping Voltammetric Detection of Arsenic(III) at Gold Nanoparticle‐Modified Glassy Carbon Electrodes Prepared by Electrodeposition in the Presence of Various Additives

The simple, fast and highly sensitive anodic stripping voltammetric detection of As(III) at a gold (Au) nanoparticle‐modified glassy carbon (GC) (nano‐Au/GC) electrode in HCl solution was extensively studied. The Au nanoparticles were electrodeposited onto GC electrode using chronocoulometric technique via a potential step from 1.1 to 0 V vs. Ag|AgCl|NaCl (sat.) in 0.5 M H₂SO₄ containing Na[AuCl₄] in the presence of KI, KBr, Na₂S and cysteine additives. Surfaces of the resulting nano‐Au/GC electrodes were characterized with cyclic voltammetry. The performances of the nano‐Au/GC electrodes, which were prepared using different concentrations of Na[AuCl₄] (0.05–0.5 mM) and KI additive (0.01–1.0 mM) at various deposition times (10–30 s), for the voltammetric detection of As(III) were examined. After the optimization, a high sensitivity of 0.32 mA cm^?2 μM^?1 and detection limit of 0.024 μM (1.8 ppb) were obtained using linear sweep voltammetry.     

Electrochemical sensor for determination of aflatoxin B1 based on multiwalled carbon nanotubes-supported Au/Pt bimetallic nanoparticles

A sensitive and selective imprinted electrochemical sensor for the determination of aflatoxin B₁ (AFB₁) was constructed on a glassy carbon electrode by stepwise modification of functional multiwalled carbon nanotubes (MCNTs), Au/Pt bimetallic nanoparticles (Au/PtNPs), and a thin imprinted film. The fabrication of a homogeneous porous poly o-phenylenediamine (POPD)-grafted Au/Pt bimetallic multiwalled carbon nanotubes nanocomposite film was conducted by controllable electrodepositing technology. The sensitivity of the sensor was improved greatly because of the nanocomposite functional layer; the proposed sensor exhibited excellent selectivity toward AFB₁ owing to the porous molecular imprinted polymer (MIP) film. The surface morphologies of the modified electrodes were characterized using a scanning electron microscope. The performance of the imprinted sensor was investigated by cyclic voltammetry, differential pulse voltammetry, and electrochemical impedance spectroscopy in detail. A linear relationship between the sensor response signal and the logarithm of AFB₁ concentrations ranging from 1?×?10^?10 to 1?×?10^?5 mol L^?1 was obtained with a detection limit of 0.03 nmol L^?1. It was applied to detect AFB₁ in hogwash oil successfully.     

A glassy carbon electrode modified with MoS<Subscript>2</Subscript> nanosheets and poly(3,4-ethylenedioxythiophene) for simultaneous electrochemical detection of ascorbic acid,dopamine and uric acid

We describe a chemical exfoliation method for the preparation of MoS₂ nanosheets. The nanosheets were incorporated into poly(3,4-ethylenedioxythiophene) (PEDOT) by electrodeposition on a glassy carbon electrode (GCE) to form a nanocomposite. The modified GCE is shown to enable simultaneous determination of ascorbic acid (AA), dopamine (DA) and uric acid (UA). Due to the synergistic effect of MoS₂ and PEDOT, this electrode displays better properties in terms of electrocatalytic oxidation of AA, DA and UA than pure PEDOT, which is illustrated by cyclic voltammetry and differential pulse voltammetry (DPV). Under optimum conditions and at pH 7.4, the respective sensitivities and best working potentials are as follows: AA: 1.20 A?mM^?1?m^?2, 30 mV; DA: 36.40 A?mM^?1?m^?2, 210 mV; UA: 105.17 A?mM^?1?m^?2, 350 mV. The calculated detection limits for AA, DA and UA are 5.83 μM, 0.52 μM and 0.95 μM, respectively. The modified electrode was applied to the detection of the three species in human urine samples and gave satisfactory results.

Open image in new window

Graphical abstract MoS₂ nanosheets were prepared by a facile chemical exfoliation method. MoS₂ and poly(3,4-ethylenedioxythiophene) nanocomposite modified glassy carbon electrodes were fabricated, which are shown to enable simultaneous determination of ascorbic acid, dopamine and uric acid with high sensitivity and selectivity.

     

Linen fiber template-assisted preparation of TiO2 nanotubes: palladium nanoparticle coating and electrochemical applications

TiO₂ nanotubes were fabricated from TiF₄ precursors within the pore channels of the linen fiber templates, resulting in crystalline fabricated titanate nanotubes (f-TNTs) upon removal by calcination at 500–600 °C. The f-TNTs were formed by the aggregation of TiO₂ nanoparticles (NPs) with a diameter of 80 nm; the wall thickness and size of the f-TNTs can be controlled by adjusting the concentration of the TiF₄ precursor, time, temperature, and the size of the linen fibers respectively. After that, palladium (Pd⁽⁰⁾) NPs were coated on the surface of the f-TNTs (Pd/f-TNTs) by the chemical reduction method, using NaBH₄ as a reducing agent. The size of the Pd⁽⁰⁾ NPs is about 10–13 nm. The Pd/f-TNT nanocomposite is systematically characterized by X-ray diffraction, high-resolution transmission electron microscopy, and field emission scanning electron microscopy. The Pd/f-TNT nanocomposite-modified glassy carbon electrodes exhibited excellent electrocatalytic activity as well as amperometric determination of hydrazine, ascorbic acid, and dopamine; these electrochemical applications were carried out by cyclic voltammetry.     

Synergetic effect of Prussian blue film with gold nanoparticle graphite–wax composite electrode for the enzyme-free ultrasensitive hydrogen peroxide sensor

Enzyme-free amperometric ultrasensitive determination of hydrogen peroxide (H₂O₂) was investigated using a Prussian blue (PB) film-modified gold nanoparticles (AuNPs) graphite–wax composite electrode. A stable PB film was obtained on graphite surface through 2-aminoethanethiol (AET)-capped AuNPs by a simple approach. Field emission scanning electron microscope studies results in formation of PB nanoparticle in the size range of 60–80 nm. Surface modification of PB film on AET–AuNPs–GW composite electrode was confirmed by Fourier transform infrared attenuated total reflection (FTIR-ATR) spectroscopy studies. Highly sensitive determination of H₂O₂ at a peak potential of ?0.10 V (vs. SCE) in 0.1 M KCl PBS, pH?=?7.0) at a scan rate of 20 mVs^?1 with a sensitivity of 23.58 μA/mM was observed with the modified electrode using cyclic voltammetry. The synergetic effect of PB film with AuNPs has resulted in a linear range of 0.05 to 7,800 μM with a detection limit of 0.015 μM for H₂O₂ detection with the present electrode. Chronoamperometric studies recorded for the successive additions of H₂O₂ with the modified electrode showed an excellent linearity (R ²?=?0.9932) in the range of 4.8?×?10^?8 to 7.4?×?10^?8 M with a limit of detection of 1.4?×?10^?8 M. Selective determination of H₂O₂ in presence of various interferents was successfully demonstrated. Human urine samples and stain remover solutions were also investigated for H₂O₂ content.     

Fabrication of a nanostructured TiO2/carbon nanotube composite electrode for voltammetric and impedimetric determination of NTO explosive in the water and soil samples

An electrochemical oxidation route was developed for sensitive and selective assay of nitrotriazolone (NTO) explosive in some environmental samples on a multi-walled carbon nanotube (MWCNTs)/TiO₂ nanocomposite paste electrode, for prevention of the analytical interference of conventional reducible energetic compounds. Detailed evaluations were made for the electrochemical behaviour of NTO on the modified electrode by adsorptive stripping voltammetry, electrochemical impedance spectroscopy (EIS) and chronoamperometry techniques in the pH range of 2.0–10.0. Parameters such as diffusion coefficient constant of NTO were calculated, and various experimental conditions were also optimised. Under optimal conditions the calibration curve had two linear dynamic ranges of 130.0–3251.5 μg L^?1 and 6.5–26.0 mg L^?1 with a detection limit of 26.0 μg L^?1 (0.2 μmol L^?1) and precision of <3%. This electrochemical sensor was further applied to determine NTO in real soil and water samples with satisfactory results.     

High Sensitive Sensor Based on Carbon Nanotube Electrode for Determination of Lanthanum in the Presence of Calcon Carboxylic Acid

In this paper we have investigated the electrochemical activity of lanthanum chloride (La (III)) in the presence of calcon carboxylic acid (CCA) using a multi-walled carbon nano tube/carbon paste electrode (CNT/CPE). The peak current increases linearly with increasing of the La (III) concentration. For this purpose, a few electrochemical methods such as cyclic, differential pulse voltammetry, linear sweep and hydrodynamic voltammetry, and chronoamperometry were used. The results show that calcon carboxylic acid as a ligand was useful for determination of La (III) and was able to improve its sensitivity. Cyclic voltammetry was used for study of reduction reaction of La (III) at the surface of modified electrode. The electrochemical parameters for La (III) at the surface of CNT/CPE, such as diffusion coefficient (D/ cm² s ^?1 = 5.26 × 10^?6), the electron transfer coefficient, (α = 0. 43), and the reduction rate constant, (k/ M s^?1 = 2.33 (±0.015) × 10²), were determined using voltammetry methods, which with the detection limit of La (III) by differential pulse voltammetry was found to be 1.3 nM. The combination of CCA with CNT as mediators in carbon paste electrode showed that this electrode is capable, sensitive, and simple to quantify La (III) in real samples with an average recovery of 97.64%.     

Titanium dioxide nanorod-based amperometric sensor for highly sensitive enzymatic detection of hydrogen peroxide

Titanium dioxide nanorods (TNR) were grown on a titanium electrode by a hydrothermal route and further employed as a supporting matrix for the immobilization of nafion-coated horseradish peroxidase (HRP). The strong electrostatic interaction between HRP and TNR favors the adsorption of HRP and facilitates direct electron transfer on the electrode. The electrocatalytic activity towards hydrogen peroxide (H₂O₂) was investigated via cyclic voltammetry and amperometry. The biosensor exhibits fast response, a high sensitivity (416.9 μA·mM^?1), a wide linear response range (2.5 nM to 0.46 mM), a detection limit as low as 12 nM, and a small apparent Michaelis-Menten constant (33.6 μM). The results indicate that this method is a promising technique for enzyme immobilization and for the fabrication of electrochemical biosensors.

Hydrogen diffusivity in the massive LaNi5 electrode using voltammetry technique

The Randles–Sev?ik relationship has been applied to evaluate atomic hydrogen diffusivity in massive LaNi₅ intermetallic compound. The electrode was cathodically hydrogenated in 6 M KOH solution (22 °C), and then voltammetry measurements were carried out at various, very slow potential scan rates (υ?=?0.01–0.1 mV?·?s^?1). At potentials more noble than the equilibrium potential of the H₂O/H₂ system, the anodic peaks were registered as a consequence of oxidation of hydrogen absorbed in cathodic range. The peak potentials linearly increase with the logarithm of the scan rate with a slope of 0.059 V. The slope testifies to a symmetric charge transfer process with symmetry factor α?=?½. The peak currents linearly increase with the square root of the potential scan rate, and the straight line runs through the origin of the coordinate system. The slope of the I _a ^(peak) ?=?f(υ ^1/2) straight line is a measure of the atomic hydrogen diffusion coefficient. Assuming the hydrogen concentration in the LaNi₅ material after cathodic exposure to be C _0,H?=?0.071 mol?·?cm^?3 (63 % of theoretical value), the hydrogen diffusion coefficient equals D _H?=?2.0?·?10^?9 cm²s^?1. Extrapolation of rectilinear segments of potentiodynamic polarization curves with Tafel slopes of 0.12 V and linear polarization dependencies from voltammetry tests allowed the exchange current densities of the H₂O/H₂ system on the tested material to be determined. The exchange current densities on initially hydrogenated LaNi₅ alloy are close to 1 mA?·?cm^?2, irrespective of the electrode potential scan rate.     

Preparation of Polypyrrole/Nuclear Fast Red Films on Gold Electrode and Its Application on the Electrocatalytic Determination of Methyl‐dopa and Ascorbic Acid

A novel voltammetric method using the Ppyox/NFR/Au (poly pyrrole – nuclear fast red – gold) modified electrode was developed for simultaneous measurement of various combinations of ascorbic acid (AA) and methyldopa (MDA). Polypyrrole film was prepared by incorporation of nuclear fast red (NFR) as doping anion, during the electropolymerization of pyrrole onto a gold (Au) electrode in aqueous solution using cyclic voltammetric (CV) method, and then it was overoxidized at constant potential. Differential pulse voltammetry was utilized for the measurement of both analytes using modified electrode. Well‐separated voltammetric peaks were observed for ascorbic acid (AA) and methyldopa at the Ppyox/NFR/Au modified electrodes with peak separation of 0.210 V. It has been found that under optimum condition (pH 3.0), the oxidation of AA and MDA at the surface of the electrode occurs at a potential about 260 and 50 mV less positive than unmodified Au electrode respectively. The current catalytic oxidation peaks showed a linear dependent on the concentration of AA and MDA in the range of 9.0×10^?6 to 1.0×10^?3 and 1.0×10^?7 to 2.0×10^?5 mol L^?1 respectively. The detection limit of 5.8×10^?6 and 5.0×10^?8 mol L^?1 (S/N=3) were obtained for AA and MDA respectively. The modified electrode was used for determination of AA and MDA in some real samples such as human serum and tablet.     

Poly(2-amino-5-(4-pyridinyl)-1, 3, 4-thiadiazole) film modified electrode for the simultaneous determinations of dopamine, uric acid and nitrite

Poly(2-amino-5-(4-pyridinyl)-1,3,4-thiadiazole) (PAPT) modified glassy carbon electrode (GCE) was fabricated and used for the simultaneous determinations of dopamine (DA), uric acid (UA) and nitrite (NO₂ ^?) in 0.1 mol?L^?1 phosphate buffer solution (PBS, pH 5.0) by using cyclic voltammetry and differential pulse voltammetry (DPV) techniques. The results showed that the PAPT modified GCE (PAPT/GCE) not only exhibited electrocatalytic activities towards the oxidation of DA, UA and NO₂ ^? but also could resolve the overlapped voltammetric signals of DA, UA and NO₂ ^? at bare GCE into three strong and well-defined oxidation peaks with enhanced current responses. The peak potential separations are 130 mV for DA–UA and 380 mV for UA–NO₂ ^? using DPV, which are large enough for the simultaneous determinations of DA, UA and NO₂ ^?. Under the optimal conditions, the anodic peak currents were correspondent linearly to the concentrations of DA, UA and NO₂ ^? in the ranges of 0.95–380 μmol?L^?1, 2.0–1,000 μmol?L^?1 and 2.0–1,200 μmol?L^?1 for DA, UA and NO₂ ^?, respectively. The correlation coefficients were 0.9989, 0.9970 and 0.9968, and the detection limits were 0.2, 0.35 and 0.6 μmol?L^?1 for DA, UA and NO₂ ^?, respectively. In 0.1 mol?L^?1 PBS pH 5.0, the PAPT film exhibited good electrochemical activity, showing a surface-controlled electrode process with the apparent heterogeneous electron transfer rate constant (k _s) of 25.9 s^?1 and the charge–transfer coefficient (α) of 0.49, and thus displayed the features of an electrocatalyst. Due to its high sensitivity, good selectivity and stability, the modified electrode had been successfully applied to the determination of analytes in serum and urine samples.     

Glucose biosensor based on new carbon nanotube-gold-titania nano-composites modified glassy carbon electrode

In this paper, a novel biosensor was prepared by immobilizing glucose oxidase （GOx） on carbon nanotube-gold-titania nanocomposites （CNT/Au/TiO2） modified glassy carbon electrode （GCE）. SEM was initially used to investigate the surface morphology of CNT/Au/TiO2 nanocomposites modified GCE, indicating the formation of the nano-porous structure which could readily facilitate the attachment of GOx on the electrode surface. Cyclic voltammogram （CV） and electrochemical impedance spectrum （EIS） were further utilized to explore relevant electrochemical activity on CNT]Au/TiO2 nanocomposites modified GCE. The observations demonstrated that the immobilized GOx could efficiently execute its bioelectrocatalytic activity for the oxidation of glucose. The biosensor exhibited a wider linearity range from 0.1 mmol L-1 to 8 mmol L^-1 glucose with a detection limit of 0.077 mmol L^- 1.     

A carbon ceramic electrode modified with bismuth oxide nanoparticles for determination of syringic acid by stripping voltammetry

A new type of carbon ceramic electrode modified with bismuth oxide nanoparticles (referred to as Bi-CCE) was fabricated via the sol-gel method. The Bi-CCE was applied to the determination of syringic acid by square wave adsorptive stripping voltammetry. The electrochemical properties of the Bi-CCE and the voltammetric response to syringic acid were investigated by cyclic voltammetry. The effects of the pH value of supporting electrolyte, of accumulation potential, accumulation time, SW mode parameters, and of possible interferents were tested. Under optimized conditions, the oxidation peak current (best measured at 0.8 V vs Ag/AgCl after an accumulation time of 20 s) increases linearly in the 0.4 to 24 μmol·L^?1 syringic acid concentration range. Other figures of merit include an LOD of 47 nmol·L^?1, a sensitivity of 3.3 μA·μmol^?1·L·cm^?2, and a relative standard deviation of 4.7% (for n = 5) at 2 μmol·L^?1 of syringic acid. The method was successfully applied to the determination of syringic acid in red, white and rose wine as well as water samples.

Open image in new window

Graphical abstract Schematic presentation of the preparation of carbon ceramic electrode (CCE) containing Bi₂O₃ nanoparticles and its application in square wave adsorptive stripping voltammetric (SW AdSV) determination of syringic acid.

     

Enhanced Specificity and Sensitivity for the Determination of Nickel(II) by Square-wave Adsorptive Cathodic Stripping Voltammetry at Disposable Graphene-modified Pencil Graphite Electrodes

Chemical sensors relying on graphene-based materials have been widely used for electrochemical determination of metal ions and have demonstrated excellent signal amplification. This study reports an electrochemically reduced graphene oxide (ERGO)/mercury film (HgF) nanocomposite-modified pencil graphite electrode (PGE) prepared through successive electrochemical reduction of graphene oxide (GO) sheets and an in situ plated HgF. The ERGO-PG-HgFE, in combination with dimethylglyoxime (DMG) and square-wave adsorptive cathodic stripping voltammetry (SW-AdCSV), was evaluated for the determination of Ni²⁺ in tap and natural river water samples. A single-step electrode pre-concentration approach was employed for the in situ Hg-film electroplating, metal-chelate complex formation, and non-electrolytic adsorption at –0.7 V. The current response due to nickel-dimethylglyoxime [Ni(II)-DMG₂] complex reduction was studied as a function of experimental paratmeters including the accumulation potential, accumulation time, rotation speed, frequency and amplitude, and carefully optimized for the determination of Ni²⁺ at low concentration levels (μg?L^?1) in pH 9.4 of 0.1 M NH₃–NH₄Cl buffer. The reduction peak currents were linear with the Ni²⁺ concentration between 2 and 16?μg?L^?1. The limits of detection and quantitation were 0.120?±?0.002?µg?L^?1 and 0.401?±?0.007?µg?L^?1 respectively, for the determination of Ni²⁺ at an accumulation time of 120?s. The ERGO-PG-HgFE further demonstrated a highly selective stripping response toward Ni²⁺ determination compared to Co²⁺. The electrode was found to be sufficiently sensitive to determine metal ions in water samples at 0.1?µg?L^?1, well below the World Health Organization standards.     

Nanobiocomposite Modified Carbon‐Ceramic Electrode Based on Nano‐TiO2‐Plant Tissue and Its Application for Electrocatalytic Oxidation of Dopamine

A new modified carbon‐ceramic electrode was prepared by incorporating TiO₂ nanoparticle into sol‐gel network by accompanying apple tissue. A mixture of fine graphite powder with 15 wt% of TiO₂ nanoparticle was used for the preparation of the carbon matrix and finally modification with a known amount weighted of apple tissue. The apple tissue containing polyphenol oxidase enzyme acts as molecular recognition element. The electrocatalytic oxidation of dopamine was investigated on the surface of the nanobiocomposite modified carbon‐ceramic electrode using cyclic voltammetry, chronoamperometry and amperometry techniques. Effect of pH, scan rate, TiO₂ percentage on the response of modified electrode was studied. The prepared modified electrode presented a linear range for dopamine from 5.0×10^?6 to 1.2×10^?3 M in buffered solutions with pH 7.4 by amperometry. The detection limit was 3.41×10^?6 M dopamine. The response of the modified carbon‐ceramic electrode and unmodified carbon‐ceramic electrode was compared.