Linear and four‐armed poly(l‐lactide)‐block‐poly(d‐lactide) copolymers and their stereocomplexation with poly(lactide)s

Linear and four‐armed poly(l ‐lactide)‐block‐poly(d ‐lactide) (PLLA‐b‐PDLA) block copolymers are synthesized by ring‐opening polymerization of d ‐lactide on the end hydroxyl of linear and four‐armed PLLA prepolymers. DSC results indicate that the melting temperature and melting enthalpies of poly (lactide) stereocomplex in the copolymers are obviously lower than corresponding linear and four‐armed PLLA/PDLA blends. Compared with the four‐armed PLLA‐b‐PDLA copolymer, the similar linear PLLA‐b‐PDLA shows higher melting temperature (212.3 °C) and larger melting enthalpy (70.6 J g^?1). After these copolymers blend with additional neat PLAs, DSC, and WAXD results show that the stereocomplex formation between free PLA molecular chain and enantiomeric PLA block is the major stereocomplex formation. In the linear copolymer/linear PLA blends, the stereocomplex crystallites (sc) as well as homochiral crystallites (hc) form in the copolymer/PLA cast films. However, in the four‐armed copolymer/linear PLA blends, both sc and hc develop in the four‐armed PLLA‐b‐PDLA/PDLA specimen, which means that the stereocomplexation mainly forms between free PDLA molecule and the inside PLLA block, and the outside PDLA block could form some microcrystallites. Although the melting enthalpies of stereocomplexes in the blends are smaller than that of neat copolymers, only two‐thirds of the molecular chains participate in the stereocomplex formation, and the crystallization efficiency strengthens. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1560–1567     

The morphology and growth of PLA stereocomplex in PLLA/PDLA blends with low molecular weights

The linear poly(L-lactide) and poly(D-lactide) (PLLA, PDLA) with relative lower molecular weights were synthesized, and PLLA/PDLA blends at various content of PDLA were prepared by solution casting. The morphology and growth of poly(lactide) stereocomplex (PLA SC) were investigated by polarized optical microscope. Results revealed that the morphology of SC in the blends strongly depended on the content of PDLA and the annealing temperature. Dendritic and irregular SC with looser structure developed in the specimens with lower content of PDLA, and regular SC spherulites with birefringent and compact structure produced in the specimens with higher content of PDLA. The growth rate (G) of SC increased gradually as the content of PDLA enhanced in the blends. As the annealing temperature enhanced, the SC with brighter and more compact structure appeared. The G value increased at first before declining as the annealing temperature elevated from the 130 to 190°C. And the nonlinear behavior of the growth of SC in the dissimilar specimens was analyzed.     

Plasticization of biodegradable stereocomplex polylactides with poly(propylene glycol)

The plasticization of stereocomplex polylactide (scPLA) with poly(propylene glycol) (PPG) is described. The poly(L-lactide) (PLLA), poly(D-lactide) (PDLA) and PPG were completely blended in chloroform before film casting to prepare scPLA/PPG blend films. The PLLA/PDLA ratio was fixed at 50/50 (w/w). The PPG blending enhanced the stereocomplex formation of the scPLA films. The stereocomplex crystallinities of the scPLA films increased as the PPG blend ratio increased, the PPG molecular weight decreased and the PDLA molecular weight decreased. The PPG blending significantly decreased the T _g and film transparency, and improved the elongation at break of the scPLA films. The results indicated that the PPG blending had an effect on the stereocomplexation and it improved the flexibility of the scPLA films.     

Synthesis and mechanochemical properties of biobased ABCBA-type pentablock copolymers comprising poly-d-lactide (A), poly-l-lactide (B) and poly(1,2-propylene succinate) (C)

The ABCBA pentablock copolymers (p-d -l -PPS) comprising poly(d -lactide) (PDLA: A), poly(l -lactide) (PLLA: B) and poly(propylene succinate) (PPS: C) were successfully synthesized by two-step ring-opening polymerization (ROP) of d - and l -lactide using a dihydroxy-terminated PPS as a macro-initiator. The pentablock copolymers revealed the high stereocomplex (sc) crystallinity, thermal stability and elastomeric property in their solution-cast films. It was found that the T_g was found to be proportional to the PPS content, whereas the T_m was proportional to their average block length. The thermal resistivity of the copolymer films was found to be as high as 202°C owing to their sc formation. The copolymers also showed improved stereocomplexibility compared to the enantiomeric mixtures of triblock copolymers (PLLA-PPS-PLLA and PDLA-PPS-PDLA) having similar PLLA and PDLA chain lengths. These pentablock copolymers can afford thermoplastic elastomers or flexible plastic materials having a 100% bio-based content, showing high heat-resistive property.     

Influence of chain extender on thermal properties and melt flow index of stereocomplex PLA

The effects of chain extension and melt blending temperature on the stereocomplex formation of 50/50 (w/w) poly(L-lactide) (PLLA)/poly(D-lactide) (PDLA) blends or stereocomplex polylactides (scPLAs) were investigated. Joncryl^® ADR 4368, a styrene-acrylic multifunctional oligomeric agent, was used as a chain extender. Differential scanning calorimetry and X-ray diffractometry were used to confirm the stereocomplex formation of the PLLA/PDLA blends. Melt flow indices (MFI) of the blends were also determined. The stereocomplex crystallinities gradually decreased with increasing blending temperature and Joncryl^® ADR 4368 ratio. The significant decrease in the MFI of scPLAs is believed to be attributed to chain extension at the blending temperatures of 170 °C and 200 °C. The MFI values of scPLAs decreased as the Joncryl^® ADR 4368 ratio and blending temperature increased. The results indicated that the chain extension has an effect on the stereocomplexation and it improved the melt strength of the scPLAs.     

Enhanced crystallization of poly(d-lactide) by xylan esters

The crystallization behavior of poly(d-lactide) loaded with xylan propionate (XylPr) and xylan butyrate (XylBu) was investigated. Non-isothermal crystallization study revealed that the crystallization temperature (T_c) of PDLA decreased by almost 30 °C when loaded with 1% XylPr or XylBu. PDLA blends containing 0.1% xylan ester produced similar results. Isothermal crystallization study suggests faster rate of crystallization of the PDLA blends as indicated by their t_1/2 values. The X_c values of the PDLA blends were also higher as compared to neat PDLA. However, the PDLA blends still possessed lower degrees of haze due to the presence of smaller spherulites. Based on TMA, PDLA blends exhibited better thermal stability than neat PDLA.     

Enhancing crystallization behavior for optimized performances of poly(TMC‐b‐(LLA‐ran‐GA)) by PDLA/PLLA stereocomplex crystallization

The blends of poly(1,3‐trimethylene carbonate‐b‐(l ‐lactide‐ran‐glycolide)) (PTLG) with poly(d ‐lactide) (PDLA) were prepared via solution‐casting method using CH₂Cl₂ as solvent. The poly(l ‐lactide) (PLLA) segments of PTLG with PDLA chain constructed as stereocomplex structures and growth stereocomplex crystals of PLA (sc‐PLA). The effects of sc‐PLA crystals on thermal behavior, mechanical properties, thermal decomposition of the PTLG/PDLA blends were investigated, respectively. The differential scanning calorimetry (DSC) and wide‐angle X‐ray diffraction (WAXD) results showed that the total crystallinity of the PTLG/PDLA blends was increased with the PDLA content increasing. Heterogeneous nucleation of sc‐PLA crystals induced crystallization of the PLLA segments in PTLG. The crystallization temperature of samples shifted to 107.5°C for the PTLG/PDLA‐20 blends compared with that of the PTLG matrix, and decreased the half‐time of crystallization. The mechanical measurement results indicated that the tensile strength of the PTLG/PDLA blends was improved from 21.1 MPa of the PTLG matrix to 39.5 MPa of PTLG/PDLA‐20 blends. The results of kinetics of thermal decomposition of the PTLG/PDLA blends by TGA showed that the apparent activation energy of the PTLG/PDLA blends was increased from 59.1 to 72.1 kJ/mol with the increasing of the PDLA content from 3 wt% to 20 wt%, which indicated the enhancement of thermal stability of the PTLG/PDLA blends by addition of PDLA. Furthermore, the biocompatibility of the PTLG/PDLA blends cultured with human adipose‐derived stem cells was evaluated by CCK‐8 and live/dead staining. The experiment results proved the PTLG/PDLA blends were a kind of biomaterial with excellent physical performances with very low cytotoxicity.     

Rheology and crystallization behavior of asymmetric PLLA/PDLA blends based on linear PLLA and PDLA with different structures

In this study, several asymmetric poly(L‐lactide)/poly(D‐lactide) (PLLA/PDLA) blends were prepared by adding small amounts of PDLA with different structures into linear PLLA matrix. The effect of PDLA on rheological behavior, crystallization behavior, nucleation efficiency and spherulite growth of PLLA was investigated. Rheological results indicated that PLLA/PDLA blends showed solid‐like viscoelastic behavior at low temperature (<200°C), and the cross‐linking density of PLLA/PDLA melt at 180°C followed the order: PLLA/6PDLA > PLLA/L‐PDLA > PLLA/3PDLA > PLLA/4PDLA. No‐isotherm and isotherm crystallization results indicated that the crystallization capacity of PLLA/PDLA blends was strongly related to the PDLA structure, crystallization temperature and thermal treatment temperature. Furthermore, the dimension of crystal growth during isotherm crystallization presented the obvious dependent on the PDLA structure. The nucleation efficiency of sc‐crystallites in the blends and spherulite density during isothermal crystallization were also studied. Nucleation efficiency of sc‐crystallites in the PLLA/S‐PDLA blends showed the obvious dependent on thermal treatment temperature with respect to PLLA/L‐PDLA, and nucleation efficiency sc‐crystallites in the PLLA/S‐PDLA blends first decreased and then increased as the thermal treatment temperature increased. Spherulite density of PLLA/PDLA blends was also related to thermal treatment temperature and the PDLA structure. This study has discussed the temperature dependence of the stereocomplex networks between PLLA and PDLA with different structure, and then its consequential influence on rheology and crystallization capacity of PLLA, which would provide the theoretical direction for PLA processing. Copyright © 2016 John Wiley & Sons, Ltd.     

Rheology and crystallization behavior of PLLA/TiO2‐g‐PDLA composites

Poly(L‐lactide) (PLLA) composites with TiO₂‐g‐poly(D‐lactide) (PDLA), which was synthesized by surface‐initiated opening ring polymerization with TiO₂ as initiator and Sn(Oct)₂ as catalyst, were prepared by solution casting. The synthesized TiO₂‐g‐PDLA was characterized by transmission electron microscope (TEM) and dynamic laser scattering (DLS), showing larger size corresponding to that of TiO₂. Fourier transform infrared spectroscopy (FT‐IR) and X‐ray photoelectron spectroscopy (XPS) measurements were further carried out and indicated that PDLA was grafted onto TiO₂ through covalent bond. For PLLA/TiO₂‐g‐PDLA composites, the stereocomplex crystallites were formed between PDLA grafted on the surface of TiO₂ and the PLLA matrix, which was determined by FT‐IR, differential scanning calorimetry (DSC), and X‐ray diffractometer (XRD). The influence of stereocomplex crystallites on the rheological behavior of PLLA/TiO₂‐g‐PDLA was investigated by rheometer, which showed greater improvement of rheological properties compared to that of PLLA/TiO₂ composites especially with a percolation content of TiO₂‐g‐PDLA between 3 wt%–5 wt%. The crystallization and melting behavior of PLLA/TiO₂‐g‐PDLA composites were studied by DSC under different thermal treatment conditions. The formed PLA stereocomplex network acted as nucleating agents and a special interphase on the functional surface of TiO₂, which resulted in imperfect PLLA crystal with lower melting temperature. When the thermal treatment was close to the melting temperature of PLA stereocomplex, the crystallinity approached to the maximum. The isothermal crystallization study by polarizing microscope (POM) indicated that stereocomplex network presented stronger nucleation capacity than TiO₂‐g‐PDLA. Copyright © 2015 John Wiley & Sons, Ltd.     

Polylactide stereocomplex crystallites as nucleating agents for isotactic polylactide

A nucleation efficiency scale for isotactic poly(L ‐lactide) (PLLA) was obtained with self‐nucleation and nonisothermal differential scanning calorimetry experiments. The maximum nucleation efficiency occurred at the highest concentration of self‐nucleating sites, and the minimum efficiency occurred in the absence of these sites (pure PLLA polymer melt). Blends of PLLA and isotactic poly(D ‐lactide) (PDLA) led to the formation of a 1/1 stereocomplex. In comparison with the homopolymer (PLLA), the stereocomplex had a higher melting temperature and crystallized at higher temperatures from the melt. Small stereocomplex crystallites were formed in PLLA/PDLA blends containing low concentrations of PDLA. These crystallites acted as heterogeneous nucleation sites for subsequent PLLA crystallization. Using the PLLA nucleation efficiency scale, we evaluated a series of PLLA/PDLA blends (0.25–15 wt % PDLA). A maximum nucleation efficiency of 66% was observed at 15 wt % PDLA. The nucleation efficiency was largely dependent on the thermal treatment of the sample. The nucleating ability of the stereocomplex was most efficient when it was formed well before PLLA crystallization. According to the efficiency scale, the stereocomplex was far superior to talc, a common nucleating agent for PLLA, in its ability to enhance the rate of PLLA crystallization. In comparison with the PLLA homopolymer, the addition of PDLA led to reduced spherulite sizes and a reduction in the overall extent of PLLA crystallization. The decreased extent of crystallization was attributed to the hindered mobility of the PLLA chains due to tethering by the stereocomplex. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 300–313, 2001     

Self-Nucleation Efficiency of PDLA in PLAs: Crystallization Behavior and Morphology

Crystallization behavior and morphology of PLA blended with 0.05–1.00 wt % loadings of poly(D-lactic acid) (PDLA) forming stereocomplex crystallites as in-situ nucleating agents, were studied using wideangle X-ray diffraction (WAXD), differential scanning calorimetry (DSC), and polarizing-light optical microscopy (POM). Blending PLA with small amount of PDLA does lead to formation of PLA stereocomplex (SC), although the PLA is a random copolymer. The in-situ formed SC crystal acted as nucleation sites in blends and accelerated the crystallization of PLA by decreasing the half-time (t_1/2). The nucleation efficiency of PDLA obviously increased and the crystallization induction time decreased while the content of PDLA reached up to 0.20 wt %. While the content of PDLA is 0.2 wt %, the nucleation efficiency of PDLA is up to 43.8%, and the induction time decreased from 430 to 88 s. In addition, compared with pure PLA, t_1/2 decreases from 15.1 to 3.5 min at T_c = 127.5°C while the amount PDLA is 1.0 wt %. The equilibrium melting temperature of PLA decreased from 187.2 to 181.2°C with the increase of PDLA content.     

Synthesis of biodegradable thermoplastic elastomers from ε‐caprolactone and lactide

This article reports the synthesis and the properties of novel thermoplastic elastomers of A‐B‐A type triblock copolymer structure, where the hard segment A is poly(l ‐lactide) (PLLA) and the soft segment B is poly(ε‐caprolactone‐stat‐d ,l ‐lactide) (P(CL‐stat‐DLLA)). The P(CL‐stat‐DLLA) block with DLLA content of 30 mol % was applied because of its amorphous nature and low glass transition temperature (T_g = approximately ?40 °C). Successive polymerization of l ‐lactide afforded PLLA‐block‐P(CL‐stat‐DLLA)‐block‐PLLAs, which exhibited melting temperature (T_m = approximately 150 °C) for the crystalline PLLA segments and still low T_g (approximately ?30 °C) of the soft segments. The triblock copolymers showed very high elongation at break up to approximately 2800% and elastic properties. The corresponding d ‐triblock copolymers, PDLA‐block‐P(CL‐stat‐DLLA)‐block‐PDLAs (PDLA = poly(d ‐lactide)) were also prepared with the same procedure using d ‐lactide in place of l ‐lactide. When the PLLA‐block‐P(CL‐stat‐DLLA)‐block‐PLLA was blended with PDLA‐block‐P(CL‐stat‐DLLA)‐block‐PDLA, stereocomplex crystals were formed to enhance their T_m as well as tensile properties. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 489–495     

Characteristics of the biodegradability and physical properties of stereocomplexes between poly(L‐lactide) and poly(D‐lactide) copolymers

Random and block copolymerizations of L ‐ or D ‐lactide with ε‐caprolactone (CL) were performed with a novel anionic initiator, (C₅Me₅)₂SmMe(THF), and they resulted in partial epimerization, generating D ,L ‐ or meso‐lactide polymers with enhanced biodegradability. A blend of PLLA‐r‐PCL [82/18; PLLA = poly(L ‐LA) and PCL = poly(ε‐caprolactone)] and PDLA‐r‐PCL [79/21; PDLA = poly(D ‐LA)] prepared by the solution‐casting method generated a stereocomplex, the melting temperature of which was about 40 °C higher than that of the nonblended copolymers. A blend of PLLA‐b‐PCL (85/15) and PDLA‐b‐PCL (82/18) showed a lower elongation at break and a remarkably higher tensile modulus than stereocomplexes of PLLA‐r‐PCL/PDLA‐r‐PCL and PLLA/PDLA. The biodegradability of a blend of PLLA‐r‐PCL (65/35) and PDLA‐r‐PCL (66/34) with proteinase K was higher than that of PLLA‐b‐PCL (47/53) and PDLA‐b‐PCL (45/55), the degradability of which was higher than that of a PLLA/PDLA blend. A blend film of PLLA‐r‐PDLLA (69/31)/PDLA‐r‐PDLLA (68/32) exhibited higher degradability than a film of PLLA/PDLLA [PDLLA = poly(D ,L ‐LA)]. A stereocomplex of PLLA‐r‐PCL‐r‐PDMO [80/18/2; PDMO = poly(L ‐3,D ,L ‐6‐dimethyl‐2,5‐morpholinedion)] with PDLA‐r‐PCL‐r‐PDMO (81/17/2) showed higher degradability than PLLA‐r‐PDMO (98/2)/PDLA‐r‐PDMO (98/2) and PLLA‐r‐PCL (82/18)/PDLA‐r‐PCL (79/21) blends. The tensile modulus of a blend of PLLA‐r‐PCL‐r‐PDMO and PDLA‐r‐PCL‐r‐PDMO was much higher than that of a blend of PLLA‐r‐PDMO and PDLA‐r‐PDMO. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 438–454, 2005     

Hydrogen bonding assists stereocomplexation in poly(l‐lactic acid)/poly(d‐lactic acid) racemic blends

In this communication, we reported the sequence variation of stereocomplex crystals (SC) and homocrystals (HC) in poly(l ‐lactic acid)/poly(d ‐lactic acid) (PLLA/PDLA) racemic blends melts. It was evidenced that the emerging sequence of the SC and HC depends on the hydrogen bond formation in the melt, and the hydrogen bond is required for the stereocomplexation in PLLA/PDLA racemic blend. First, by combining a commercial fast‐scan chip‐calorimeter (Flash DSC 1) and micro‐FTIR, we found that hydrogen bonds were formed in the melt during cooling at 2.5 K/s, but not at 3000 K/s. Second, annealing the melt without hydrogen bonds at 100 °C led to HC emerging first, while annealing the melt with hydrogen bonds resulted in SC emerging at first. Third, the crystallization kinetics of the racemic blends after cooling to predefined T_c at 2.5 or 3000 K/s further verified that the hydrogen bonding can be inhibited effectively by cooling the racemic blends isotropic melt at fast enough rate. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 83–88     

Calorimetric analysis of the multiple melting behavior of melt-crystallized poly(l-lactic acid) with a low optical purity

The polymorphous crystallization and multiple melting behavior of poly(l-lactic acid) (PLLA) with an optical purity of 92 % were investigated after isothermally crystallized from the melt state by wide-angle X-ray diffraction and differential scanning calorimetry. Owing to the low optical purity, it was found that the disordered (α′) and ordered (α) crystalline phases of PLLA were formed in the samples crystallized at lower (<95 °C) and higher (≥95 °C) temperatures, respectively. The melting behavior of PLLA is different in three regions of crystallization temperature (T _c) divided into Region I (T _c < 95 °C), Region II (95 °C ≤ T _c < 120 °C), and Region III (T _c ≥ 120 °C). In Region I, an exothermic peak was observed between the low-temperature and high-temperature endothermic peaks, which results from the solid–solid phase transition of α′-form crystal to α one. In Region II, the double-melting peaks can be mainly ascribed to the melting–recrystallization–remelting of less stable α crystals. In Region III, the single endotherm shows that the α crystals formed at higher temperatures are stable enough and melt directly without the recrystallization process during heating.     

An efficient solid‐state polycondensation method for synthesizing stereocomplexed poly(lactic acid)s with high molecular weight

Simultaneous solid‐state polycondensation (SSP) of the powdery prepolymers of poly(L ‐lactic acid) (PLLA) and poly(D ‐lactic acid) (PDLA) can produce entire stereocomplexed poly(lactic acid)s (sc‐PLA) with high molecular weight and can be an alternative synthetic route to sc‐PLA. Ordinary melt polycondensations of L ‐ and D ‐lactic acids gave the PLLA and PDLA prepolymers having medium molecular weight which were pulverized for blending in 1:1 ratio. The resultant powder blends were then subjected to SSP at 130–160 °C for 30 h under a reduced pressure of 0.5 Torr. Some of the products thus obtained attained a molecular weight (M_w) as high as 200 kDa, consisting of stereoblock copolymer of PLLA and PDLA. A small amount of the stereocomplex should be formed in the boundaries of the partially melted PLLA and PDLA where the hetero‐chain connection is induced to generate the blocky components. The resultant SSP products showed predominant stereocomplexation after their melt‐processing in the presence of the stereoblock components in spite of containing a small amount of racemic sequences in the homo‐chiral PLLA and PDLA chains. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3714–3722, 2008     

Influence of graphene nanosheets on stereocomplex crystallization behaviors of star‐shaped poly (D(L)‐lactide) stereoblock copolymer

The nanocompsites of star‐shaped poly(D‐lactide)‐co‐poly(L‐lactide) stereoblock copolymers (s‐PDLA‐PLLA) with two‐dimensional graphene nanosheets (GNSs) were prepared by solution mixing method. Crystallization behaviors were investigated using differential scanning calorimetry, polarized optical microscopy, and wide angle X‐ray diffraction. The results of isothermal crystallization behaviors of the nanocompsites clearly indicated that the GNS could remarkably accelerate the overall crystallization rate of s‐PDLA‐PLLA copolymer. Unique stereocomplex crystallites with melting temperature about 207.0°C formed in isothermal crystallization for all samples. The crystallization temperatures of s‐PDLA‐PLLAs shifted to higher temperatures, and the crystallization peak shapes became sharper with increasing GNS contents. The maximum crystallization temperature of the sample with 3 wt% GNS was about 128.2°C, ie, 15°C higher than pure s‐PDLA‐PLLA. At isothermal crystallization processes, the halftime of crystallization (t_0.5) of the sample with 3 wt% GNS decreased to 6.4 minutes from 12.9 minutes of pure s‐PDLA‐PLLA at 160°C.The Avrami exponent n values for the nanocomposites samples were 2.6 to 3.0 indicating the crystallization mechanism with three‐dimensional heterogeneous nucleation and spherulites growth. The morphology and average diameter of spherulites of s‐PDLA‐PLLA with various GNS contents were observed in isothermal crystallization processes by polarized optical microscopy. Spherulite growth rates of samples were evaluated by using combined isothermal and nonisothermal procedures and analyzed by the secondary nucleation theory. The results evidenced that the GNS has acceleration effects on the crystallization of s‐PDLA‐PLLA with good nucleation ability in the s‐PDLA‐PLLA material.     

Fractionated Crystallization Kinetics and Polymorphic Homocrystalline Structure of Poly(L-lactic acid)/Poly(D-lactic acid) Blends: Effect of Blend Ratio

Stereocomplex (SC) crystallization has been an effective way to improve the physical performances of stereoregular polymers. However, the competition between homo and SC crystallizations can lead to more complicated crystallization kinetics and polymorphic crystalline structure in stereocomplexable polymers, which influences the physical properties of obtained materials. Herein, we select the medium-molecular-weight (MMW) poly(_L-lactic acid)/poly(_D-lactic acid) (PLLA/PDLA) asymmetric blends with different PDLA fractions (f_D=0.01–0.5) as the model system and investigate the effects of f_D and crystallization temperature (T_c) on the crystallization kinetics and polymorphic crystalline structure. We observe the fractionated (i.e., multistep) crystallization kinetics and the formation of peculiar β-form homocrystals (HCs) in the asymmetric blends under quiescent conditions, which are strongly influenced by both f_D and T_c. Precisely, crystallization of β-form HCs is favorable in the MMW PLLA/PDLA blends with high f_D (≥0.2) at a low T_c (80–100 °C). It is proposed that the formation of metastable β-form HCs is attributed to the conformational matching between β-form HCs and SCs, and the stronger constrain effects of precedingly-formed SCs in the early stage of crystallization. Such effects can also cause the multistep crystallization kinetics of MMW PLLA/PDLA asymmetric blends in the heating process.

     

Miscibility and hydrolytic degradation in alkaline solution of poly(l-lactide) and poly(p-vinyl phenol) blends

Poly(l-lactide) (PLLA) was melt-blended with poly(p-vinyl phenol) (PVPh) using a two-roll mill, and the miscibility between PLLA and PVPh and degradation of the blend films were investigated. It was found that PLLA/PVPh blend has miscibility in the amorphous state because only single T_g was observed in the DSC and DMA measurements. The T_g of the PLLA/PVPh blend could be controlled in the temperature range from 55 °C to 117 °C by changing the PVPh weight fraction. In alkaline solution, degradation rate of PLLA/PVPh blends was faster than that of neat PLLA because PVPh could dissolve in alkaline solution. The surface morphology of degraded PLLA and PLLA/PVPh blend were observed by SEM. The surface morphology of degraded PLLA/PVPh blend was finer than that of PLLA. Young's modulus of PLLA/PVPh blend increased with increasing PVPh content. Yield stress of PLLA/PVPh blends whose PVPh content was less than 30 wt% kept the level of about 55 MPa and that of PLLA/PVPh blend whose PVPh content was 40 wt% is much lower than that of neat PLLA.     

Synthesis and characterization of well-defined star PLLA with a POSS core and their microspheres for controlled release

In this paper, a series of hybrid star PLLA (sPLLA) with different arm lengths was synthesized via the hydrosilylation between octakis(dimethylsiloxy) silsesquioxane (Q₈M₈) and functionalized PLLA macromolecules with vinyl end groups (mPLLA). mPLLA was synthesized by ring-opening polymerization of l-lactide using 2-hydroxyethylmethacryl as an initiator in the presence of stannous 2-ethylhexanoate as a catalyst. The obtained sPLLA has low polydispersity with polydispersity index values from 1.29 to 1.30. The arm numbers of sPLLA vary from 5 to 7 and decrease with the increase in the length of the mPLLA arm due to the steric hindrance, which are estimated by ¹H NMR analysis. The branched structure of sPLLA is also evidenced by the lower intrinsic viscosity when compared with the linear mPLLA with similar molecular weight. Both the glass transition temperatures (T _g’s) and melting temperatures (T _m’s) of sPLLAs are higher than those of the mPLLA arms. The incorporation of polyhedral oligomeric silsesquioxane (POSS) does not change the crystalline structure of PLLA, while the crystallinity of sPLLA is enhanced as the result that the POSS core acts as a heterogeneous nucleating agent in the matrix to promote the crystallization ability of PLLA. High-resolution transmission electron microscopy observation suggests that POSS disperses in the crystalline PLLA matrix as 5–20 nm aggregates. Microspheres of sPLLA with mean diameter 1 to 2 μm were prepared via emulsion solvent evaporation method. The sPLLA microspheres have higher loading capacity and encapsulation efficiency and lower drug release rate than mPLLA microspheres.