Highly fluorinated low‐molecular‐weight photoresists for optical waveguides

A series of highly fluorinated polymers were synthesized by copolymerization of 2,3,4,5,6‐pentafluorostyrene (PFS) and fluorinated styrene derivate monomer (FSDM). Their chemical structure were confirmed by ¹H NMR, ¹³C NMR, and ¹⁹F NMR spectra. The refractive index and cross‐linking density of the polymers can be tuned and controlled by monitoring the feed ratio of comonomers. A series of negative‐type low‐molecular‐weight fluorinated photoresists (NFPs) were prepared by composing of fluorinated polystyrene derivates (FPSDs), diphenyl iodonium salt as a photoacid generator (PAG) and solvent. The polymer films prepared from NFP by photocuring exhibited excellent chemical resistance and thermal stabilities (T_d ranged from 230.5 to 258.1 °C). A clear negative pattern was obtained through direct UV exposure and chemical development. For waveguides without upper cladding, the propagation loss of the channel waveguides was measured to be 0.25 dB/cm at 1550 nm. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Low‐molecular‐weight color pI markers to monitor on‐line the peptide focusing process in OFFGEL fractionation

High‐throughput mass spectrometry‐based proteomic analysis requires peptide fractionation to simplify complex biological samples and increase proteome coverage. OFFGEL fractionation technology became a common method to separate peptides or proteins using isoelectric focusing in an immobilized pH gradient. However, the OFFGEL focusing process may be further optimized and controlled in terms of separation time and pI resolution. Here we evaluated OFFGEL technology to separate peptides from different samples in the presence of low‐molecular‐weight (LMW) color pI markers to visualize the focusing process. LMW color pI markers covering a large pH range were added to the peptide mixture before OFFGEL fractionation using a 24‐wells device encompassing the pH range 3–10. We also explored the impact of LMW color pI markers on peptide fractionation labeled previously for iTRAQ. Then, fractionated peptides were separated by RP_HPLC prior to MS analysis using MALDI‐TOF/TOF mass spectrometry in MS and MS/MS modes. Here we report the performance of the peptide focusing process in the presence of LMW color pI markers as on‐line trackers during the OFFGEL process and the possibility to use them as pI controls for peptide focusing. This method improves the workflow for peptide fractionation in a bottom‐up proteomic approach with or without iTRAQ labeling.     

Surface modification of ultrahigh‐molecular‐weight polyethylene fibers

To prevent the loss of fiber strength, ultrahigh‐molecular‐weight polyethylene (UHMWPE) fibers were treated with an ultraviolet radiation technique combined with a corona‐discharge treatment. The physical and chemical changes in the fiber surface were examined with scanning electron microscopy and Fourier transform infrared/attenuated total reflectance. The gel contents of the fibers were measured by a standard device. The mechanical properties of the treated fibers and the interfacial adhesion properties of UHMWPE‐fiber‐reinforced vinyl ester resin composites were investigated with tensile testing. After 20 min or so of ultraviolet radiation based on 6‐kW corona treatment, the T‐peel strength of the treated UHMWPE‐fiber composite was one to two times greater than that of the as‐received UHMWPE‐fiber composite, whereas the tensile strength of the treated UHMWPE fibers was still up to 3.5 GPa. The integrated mechanical properties of the treated UHMWPE fibers were also optimum. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 463–472, 2004     

Electrospinning of ultrahigh‐molecular‐weight polyethylene nanofibers

The electrospinning method has been employed to fabricate ultrafine nanofibers of ultrahigh‐molecular‐weight polyethylene for the first time with a mixture of solvents of different dielectric constants and conductivities. The possibility of producing highly oriented nanofibers from ultrahigh‐molecular‐weight polymers suggests new ways of fabricating ultrastrong, porous, and single‐component nanocomposite fibers with improved properties. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 766–773, 2007     

Poly(dimethylsiloxane)‐based polymer organogelators with L‐lysine derivatives as a organogelation‐causing segment

New poly(dimethylsiloxane)‐based polymer organogelators with L ‐lysine derivatives were synthesized on the basis of synthetically simple procedure, and their organogelation abilities were investigated. These polymer organogelators have a good organogelation ability and form organogels in many organic solvents. In the organogels, polymer gelators constructed a mesoporous structure with a pore size of about 1 μm formed by entanglement of the self‐assembled nanofibers. The L ‐lysine derivatives in the polymer gelators functioned as a gelation‐causing segment and the organogelation was induced by self‐assembly of the L ‐lysine segments through a hydrogen bonding interaction. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3817–3824, 2006     

Synthesis and properties of high‐molecular‐weight stereo di‐block polylactides with nonequivalent D/L ratios

Di‐stereoblock polylactides (di‐sb‐PLA: PLLA‐b‐PDLA) having high molecular weight (M_n > 100 kDa) were successfully synthesized by two‐step ring‐opening polymerization (ROP) of L ‐ and D ‐lactides using tin(2‐ethylhexanoate) as a catalyst. By optimizing the polymerization conditions, the block sequences were well regulated at non‐equivalent feed ratios of PLLA and PDLA. This synthetic method consisted of three stages: (1) polymerization of either L ‐ or D ‐lactide to obtain a PLLA or PDLA prepolymer with a molecular weight less than 50 kDa, (2) purification of the obtained prepolymer to remove residual lactide, and (3) polymerization of the enantiomeric lactide in the presence of the purified prepolymer. Their ¹³C and ³¹P NMR spectra of the resultant di‐sb‐PLAs strongly supported their di‐stereo block structure. These di‐sb‐PLAs, having weight‐average molecular weights higher than 150 kDa, were fabricated into polymer films by solution casting and showed exclusive stereocomplexation. The thermomechanical analysis of the films revealed that their heat deformation temperature was limited probably because of their low crystallinity owing to the non‐equivalent PLLA/PDLA ratio. The blend systems of the di‐sb‐PLAs having complementary stereo‐sequences (the one with a long PLLA block and the other with long PDLA block) were also prepared and characterized to enhance the sc crystallinity. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 794–801, 2010     

High‐molecular‐weight poly(1,5‐dioxepan‐2‐one) via enzyme‐catalyzed ring‐opening polymerization

To avoid organometallic catalysts in the synthesis of poly(1,5‐dioxepan‐2‐one), the enzymatic ring‐opening polymerization of 1,5‐dioxepan‐2‐one (DXO) was performed with lipase CA (derived from Candida antarctica) as a biocatalyst. A linear relationship between the number‐average molecular weight and monomer conversion was observed, and this suggested that the product molecular weight could be controlled by the stoichiometry of the reactants. The monomer consumption followed a first‐order rate law with respect to the monomer, and no chain termination occurred. Water acted as a chain initiator, but it could cause polymer hydrolysis when it exceeded an optimum level. An initial activation via the heating of the enzyme was sufficient to start the polymerization, as the monomer conversion occurred when samples were left at room temperature after an initial heating at 60 °C. A high lipase content led to a high monomer conversion as well as a high molecular weight. An increase in the monomer conversion and molecular weight was observed when the polymerization temperature was increased from 40 to 80 °C. A further increase in the polymerization temperature led to a decrease in the monomer conversion and molecular weight because of the denaturation of the enzyme at elevated temperatures. The polymerization behavior of DXO under lipase CA catalysis was compared with that of ε‐caprolactone (CL). The rate of monomer conversion of DXO was much faster than that of CL, and this may have been due to differences in their specificity toward lipase CA. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4206–4216, 2005     

Luminescent lanthanide molecular‐based hybrid materials bridged through novel urethane linkages

Novel organosilicates with covalently linked functional modified aromatic acid have been synthesized from 3‐aminopropyl triethoxysilane (APS) grafted 4‐ethoxy benzoic acid (EB‐Si) and terbium ions via a simple low‐temperature route. The existence of covalent bonds between EB‐Si and silica matrices was shown by the hydrolysis and polycondensation processes of ethoxysilyl groups. Luminescence spectra were used to characterize the photophysical properties of the obtained hybrid material and the above spectroscopic data reveal that the triplet energy of modified para ethoxy benzoic acid in this favorable hybrid system matches the emissive energy level of RE³⁺. Copyright © 2006 John Wiley & Sons, Ltd.     

Synthesis of ultra‐high‐molecular‐weight ethylene‐propylene copolymer via quasi‐living copolymerization with N‐heterocyclic carbene ligated vanadium complexes

The quasi‐living copolymerization of ethylene with propylene was achieved by using N‐heterocyclic carbene (NHC) ligated vanadium complex ( V3 , VOCl₃[1,3‐(2,6‐ⁱPr₂C₆H₃)₂(NCH?)₂C:]) due to the stabilization of active center by the introduction of bulky and electron rich NHC ligand with bulky isopropyl substituents at the ortho positions of the phenyl rings. The weight‐average molecular weight (M_w) of the resulting copolymer increases linearly with its weight in 20 min. The ultra‐high‐molecular‐weight (UHMW) ethylene‐propylene copolymer (M_w = 1612 kg mol^?1) can be synthesized with V3 /Et₃Al₂Cl₃ catalytic system. The novel complex V4′ (VCl₃[1,3‐(2,4,6‐Me₃C₆H₂)₂(NCH?)₂C:]·2THF) was constructed by the introduction of two coordinated tetrahydrofuran molecules and decrease in steric hindrance at the ortho positions of phenyl rings. The UHMW ethylene‐propylene copolymer (M_w = 1167 kg mol^?1) can also be synthesized by using V4′ /Et₃Al₂Cl₃ catalytic system. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 553–561     

New polymer organogelators with L‐isoleucine and L‐valine as a gelation‐causing segment: Organogelation by a combination of supramolecular polymer and conventional polymer

New polymer organogelators, which are composed of poly(ethylene glycol), poly(propylene glycol), and poly(dimethylsiloxane)s as a polymer segment and L ‐isoleucine and L ‐valine derivatives as a gelation‐causing segment, were synthesized, and their organogelation properties were examined in organic solvents and oils. These polymer organogelators formed organogels in many organic solvents and oils, and their gels were thermally stable and had a high mechanical strength. Furthermore, the effects of the polymer backbone on the organogelation is discussed using FTIR spectroscopy, field emission scanning electron microscope observation, and analysis of thermal stability and strength of the organogel. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 353–361, 2008     

Using Cyclopenta[2,1‐b:3,4‐c′]dithiophene‐4‐one as a Building Block for Low‐Bandgap Conjugated Copolymers Applied in Solar Cells

A novel electron‐accepting unit cyclopenta[2,1‐b:3,4‐c′]dithiophene‐4‐one (CPDTO‐c′), which is an isomer of CPDTO‐b′ was developed. CPDTO‐c′ can be incorporated into the D–A backbone through 5, 7 positions. The 2 position of CPDTO‐c′ can be easily functionalized with an electron‐withdrawing chain. By copolymerizing CPDTO‐c′ with four different donor units: benzo[1,2‐b:4,5‐b′]dithiophene (BDT), dithieno[3,2‐b:2′,3′‐d]silole (DTS), carbazole, and fluorene, four new conjugated copolymers P1 – P4 were obtained. All these polymers have good solubility and low‐lying HOMO energy levels (−5.41 ∼ −5.92 eV). Among them, P1 and P2 exhibit broad absorption and narrow optical bandgaps of 1.91 and 1.72 eV, respectively. Solar cells based on P1 /PC₇₁BM afforded a PCE up to 2.72% and a high V_oc up to ∼0.9 V.     

Towards advanced circuit board materials: adhesion of copper foil to ultra‐high molecular weight polyethylene composite

Polyethylene based composites are attractive materials for advanced circuit board applications because of their unique combination of properties: low dielectric constant and loss factor, light weight, high flexural modulus and low thermal expansion coefficient controlled in all spatial directions. This investigation describes a process to consolidate chopped fibers of ultra‐high molecular weight polyethylene concurrently with its bonding to a copper foil. Bonding is affected by a thin sheet of low‐density polyethylene, incorporating a crosslinking agent with a concentration gradient across the sheets thickness. In this single step process, the composite material is formed and bonded to the metal foil, achieving good adhesion without the use of extraneous glue. Copyright © 2002 John Wiley & Sons, Ltd.     

High‐molecular‐weight AB‐type benzoxazines as new precursors for high‐performance thermosets

Novel high‐molecular‐weight polybenzoxazine precursors, namely AB‐type benzoxazine precursors, were synthesized from aminophenols and formaldehyde. Both ¹H NMR and IR confirmed the structure of the precursors, indicating the presence of a cyclic benzoxazine structure in the backbone of the precursors. The weight‐average molecular weight was estimated by size exclusion chromatography to be to in the range of 1300–4500. The precursors gave self‐standing thin films when their solutions were cast in dioxane over glass plates and dried, and upon a gradual thermal cure up to 250 °C, they afforded polybenzoxazine films. The viscoelastic analyses showed that the glass transition temperatures of the polybenzoxazine films obtained from these novel precursors were as high as 260–300 °C. Thermogravimetric analysis results indicated that the onset of decomposition and the char yield of the thermosets derived from these AB‐type precursors were higher than those of traditional polybenzoxazine. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1878–1888, 2007.     

Super‐fast oil uptake using porous ultra‐high molecular weight polyethylene sheets

This paper presents the oil uptake of porous sorbent polymer sheets consisting of ultra‐high molecular weight polyethylene. A comprehensive set of experiments are performed showing the saturation contact time, retention value, mechanical properties, oil pick‐up ratio, pick‐up density, and dynamic dripping profile. Kinetic modeling of the oil sorption is also provided. The experimental results show a good correlation with the pseudo‐second order model. The sheets exhibit high oil uptake speeds, requiring less than 2 min in contact with the oil to reach saturation. The sheets fulfill the criteria of high uptake kinetics, high sorption capacity, and high mechanical strength simultaneously. Those characteristics enable their use in practical spill response. Copyright © 2014 John Wiley & Sons, Ltd.     

Low‐Voltage All‐Polymer Field‐Effect Transistor Fabricated Using an Inkjet Printing Technique

Summary: An all‐polymer field‐effect transistor (FET) fabricated using an inkjet printing technique is presented in this paper. Poly(3,4‐ethylenedioxythiophene) works as the source/drain/gate electrode material because of its good conductivity. Polypyrrole acts as the semiconducting layer. Poly(vinyl pyrrolidone) K60, an insulating polymer with a dielectric constant of 60, operates as the dielectric layer. All the polymers are diluted with deionized water, and can be printed with a piezoelectric inkjet printing system. The device functions at a depletion mode with low operation voltage. It has a field‐effect mobility of 0.1 cm² · V⁻¹ · s⁻¹, an on/off ratio of 2.9 × 10³, and a subthreshold slope of 2.81 V · decade⁻¹.

Schematic of the all‐polymer FET synthesized here.     

Highly cis‐1,4 selective polymerization of isoprene promoted by α‐diimine cobalt(II) chlorides

A series of 1,2‐bis(arylimino)acenaphthylenes ( L1 – L5 ) was synthesized and reacted with CoCl₂ to afford the corresponding cobalt complexes LCoCl₂ ( C1 – C5 ). All cobalt complexes have been fully characterized and in the case of C1 by single crystal X‐ray diffraction; its molecular structure reveals a distorted tetrahedral geometry. On activation with AlEtCl₂, C1 – C5 efficiently polymerize isoprene to give polyisoprenes (PIs) with high contents of cis‐1,4 units (between 90% and 94%). The influence of reaction temperature and [Al]/[Co] molar ratio on both catalytic performance and the microstructural properties of the PIs is investigated. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3609–3615.     

Prediction of the Bivariate Molecular Weight‐Long Chain Branching Distribution in High‐Pressure Low‐Density Polyethylene Autoclaves

In the present study a population balance approach is described to follow the time evolution of bivariate molecular weight‐long chain branching (MW‐LCB) distributions in high pressure low density polyethylene autoclaves. The model formulation is based on a sectional grid method, the so‐called fixed pivot technique (FPT). According to this method, the ‘live’ and ‘dead’ polymer chain populations are assigned to a selected number of discrete points. Then, the resulting dynamic discrete‐continuous molar species equations for ‘live’ and ‘dead’ polymer chains are solved at the specified grid points. It is shown that a very good agreement exists between theoretical results and experimental data which proves the capability of the FPT method in calculating the joint MW‐LCB distribution for branched polymers.

     

About crosslinking of low molecular weight ethylene‐propylene(‐diene) copolymer‐based artificial latices

Crosslinking of artificial latices based on ethylene–propylene copolymers (EPM) and/or ethylene–propylene–diene copolymers (EPDM) has not thoroughly been studied yet. Moreover, crosslinking of EPM and/or EPDM particles is a prerequisite for the formation of a shell using seeded emulsion polymerization of, for example, methyl methacrylate (MMA), as described elsewhere. Therefore, the aim of this article is to improve the general understanding of the chemistry involved in the crosslinking process. This work especially emphasizes the influence of the initiation method, that is, a peroxide or a pulsed electron‐beam, on crosslinking efficiency. All crosslinking efficiencies were obtained after extraction of the soluble polymer by tetrahydrofuran. The incorporation of the coagent, that is, divinylbenzene, into the EPM/EPDM phase was studied on a microscopic level by solid‐state ¹³C and ¹H nuclear magnetic resonance (NMR). Crosslinking of a low molecular weight EPM/EPDM latex requires the presence of a coagent, for example, divinylbenzene, 1,6‐hexanediol diacrylate, or poly(1,2‐butadiene). The efficiency of crosslinking initiated by a pulsed electron‐beam was improved to a great extent by the presence, in the aqueous phase, of potassium nitrosodisulfonate, also referred to as Fremy salt. Matrix Assisted Laser Desorption/Ionization–Time of Flight–Mass Spectrometry (MALDI‐TOF‐MS) was used to determine the influence of electron‐beam irradiation on the chemical stability of surfactants. It was demonstrated that sodium dodecyl benzene sulfonate (SDBS) is not degraded by the irradiation, and is therefore the surfactant of choice for the stabilization of EPM/EPDM‐based latices subjected to electron‐beam irradiation. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3600–3615, 2005     

AGET ATRP in water and inverse miniemulsion: A facile route for preparation of high‐molecular‐weight biocompatible brush‐like polymers

Activators generated by electron transfer for atom transfer radical polymerization (AGET ATRP) of oligo(ethylene glycol) monomethyl ether methacrylate (OEOMA) was investigated in homogeneous aqueous solution targeting DP = 1000, and in inverse miniemulsion targeting DP = 600, at 30 °C. Several reaction parameters were examined in the preparation of biocompatible, brush‐like, high‐molecular‐weight, water‐soluble polymers. They include concentration of ascorbic acid (AscA), ratio of water to OEOMA, mode of addition of AscA, and ratio of initiator to Cu(II) complex. The results obtained in these studies indicate that AGET ATRP retains all of the benefits of normal ATRP and, additionally, provides a facile route for the preparation of well‐controlled high‐molecular‐weight polymers because of the use of oxidatively stable catalyst precursors. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1771–1781, 2009     

A New Low‐Bandgap Polymer Containing Benzene‐Fused Quinoxaline: Significantly Enhanced Performance Caused by One Additional Benzene Ring

Two new alkoxy‐substituted quinoxaline (Qx)‐based copolymers, PBDTQx and PBDTPz, are designed and synthesized. The only difference between these two polymers is that two methyl groups of the Qx are replaced by one additional fused benzene ring. The UV–Vis absorptions, thermal stability, energy levels, field‐effect carrier mobility, and photovoltaic characteristics of the two copolymers are systematically evaluated to understand the relationships between the polymer structure at the molecular level and the photovoltaic performances. Photovoltaic cells based on the PBDTPz with a structure of ITO/PEDOT:PSS/Polymer:PC₇₁BM/PEO/Ca/Al exhibit a promising efficiency of 4.40%, while that of PBDTQx is relatively much poorer.