Allyl ether of aralkyl phenolic resin with low melt viscosity and its Alder‐ene blends with bismaleimide: synthesis,curing, and laminate properties

This paper outlines the synthesis and characterization of O‐allyl aralkyl phenolic (O‐allyl Xylok, OAX) resins having low melt viscosity and its Alder‐ene blends with 2, 2′‐bis 4‐[(4′‐maleimido phenoxy) phenyl] propane. The blends manifested a three‐stage curing pattern that converged to a two‐stage pattern on enhancing the maleimide content. The polymerization kinetics of typical allyl and maleimide rich resin systems showed apparent activation energy increasing and pre‐exponential factor decreasing from ene to the Diels–Alder step. Increased allyl content improved mechanical and impact properties of the composites at ambient temperature, although it diminished the retention of interlaminar shear strength at elevated temperature. Increased maleimide content of the resin was conducive for the higher rigidity for the composite and its retention at elevated temperature. A substantial increase in T_g (from 153°C to 280°C) and thermal stability was observed with an increase in maleimide content. High allyl content resulted in improved mechanical properties thanks to better resin–reinforcement interaction as revealed from morphological analysis. Copyright © 2014 John Wiley & Sons, Ltd.     

Benzoxazine-bismaleimide blends: Curing and thermal properties

A blend of bisphenol A based benzoxazine (Bz-A) and a bismaleimide (2,2-bis[4(4-maleimidophenoxy) phenyl] propane (BMI), was thermally polymerised in varying proportions and their cure and thermal characteristics were investigated. The differential scanning calorimetric analysis, supplemented by rheology confirmed a lowering of the cure temperature of BMI in the blend implying catalysis of the maleimide polymerisation by benzoxazine. FTIR studies provided evidences for the H-bonding between carbonyl group of BMI and -OH group of polybenzoxazine in the cured matrix. The cured matrix manifested a dual phase behaviour in SEM and DMTA with the minor phase constituted by polybenzoxazine dispersed in an interpenetrating polymer network (IPN) of polybenzoxazine and cured BMI. The IPN possessed improved thermal stability over the constituent polybenzoxazine. A benzoxazine monomer possessing allyl functional groups, 2,2′-bis(8-allyl-3-phenyl-3,4-dihydro-2H-1,3-benzoxazinyl) propane (Bz-allyl) was reactively blended with the same bismaleimide in varying stoichiometric ratios (Bz-allyl/BMI), where the curing involved mainly Alder-ene reaction between allyl- and maleimides groups and ring-opening polymerisation of benzoxazine. The rheological analysis showed the absence of catalytic polymerisation of BMI in this case. The overall processing temperature was lowered in the blend owing to the co-reaction of the two systems to form a single-phase matrix. The cured resins of both Bz-A/BMI and Bz-allyl/BMI blends exhibited better thermal stability than the respective polybenzoxazines. The T_g of the IPN was significantly improved over that of polybenzoxazine (Bz-A). However, the co-reaction resulted in a marginal decrease in the T_g of the system in comparison to the polybenzoxazine (Bz-allyl).     

Improvement of thermoplasticity for s‐BPDA/PDA by copolymerization and blend with novel asymmetric BPDA‐based polyimides

Asymmetric biphenyl type polyimides (PI) derived from 2,3,3′,4′‐biphenyltetracarboxylic dianhydride (a‐BPDA) and p‐phenylenediamine (PDA) or 4,4′‐oxydianiline (ODA) show higher T_gs, and much better thermoplasticity than the corresponding isomeric PIs from symmetric 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (s‐BPDA). In addition, a‐BPDA‐derived PIs are completely amorphous owing to their bent chain structures and highly distorted conformations, whereas the PIs from s‐BPDA are semicrystalline. a‐BPDA‐derived PIs possessing these properties or the a‐BPDA monomer were used as a flexible blend component or a comonomer to improve the insufficient thermoplasticity of semirigid s‐BPDA/PDA homo polymer. The blends composed of s‐BPDA/PDA (80%) with a‐BPDA‐derived PIs (20%), as well as the s‐BPDA/PDA‐based copolymer containing 20% a‐BPDA, showed a certain extent of thermoplasticity above the T_gs without causing a decrease in T_g. In addition, these blends and copolymer provided comparatively low thermal expansion coefficient (ca. 18 ppm). The improved film properties for the blends are related to good blend miscibility. On the other hand, when s‐BPDA/ODA was used as a flexible matrix polymer instead of a‐BPDA‐derived PIs, the 80/20 blend film annealed at 400°C exhibited no prominent softening at the T_g. This result arises from annealing‐induced crystallization of the flexible s‐BPDA/ODA component. Thus, these results revealed that a‐BPDA‐derived PIs are promising candidates as matrix polymers for semirigid s‐BPDA/PDA for the present purpose. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2499–2511, 1999     

Miscibility and phase structure of binary blends of polylactide and poly(methyl methacrylate)

Blends of amorphous poly(DL‐lactide) (DL‐PLA) and crystalline poly(L‐lactide) (PLLA) with poly(methyl methacrylate) (PMMA) were prepared by both solution/precipitation and solution‐casting film methods. The miscibility, crystallization behavior, and component interaction of these blends were examined by differential scanning calorimetry. Only one glass‐transition temperature (T_g) was found in the DL‐PLA/PMMA solution/precipitation blends, indicating miscibility in this system. Two isolated T_g's appeared in the DL‐PLA/PMMA solution‐casting film blends, suggesting two segregated phases in the blend system, but evidence showed that two components were partially miscible. In the PLLA/PMMA blend, the crystallization of PLLA was greatly restricted by amorphous PMMA. Once the thermal history of the blend was destroyed, PLLA and PMMA were miscible. The T_g composition relationship for both DL‐PLA/PMMA and PLLA/PMMA miscible systems obeyed the Gordon–Taylor equation. Experiment results indicated that there is no more favorable trend of DL‐PLA to form miscible blends with PMMA than PLLA when PLLA is in the amorphous state. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 23–30, 2003     

Phase behavior of ternary poly‐(2‐vinylpyridine)/poly‐(N‐vinyl‐2‐pyrrolidone)/bis‐(4‐hydroxyphenyl)methane blends

The phase behavior of ternary poly‐(2‐vinylpyridine) (P2VPy)/poly‐(N‐vinyl‐2‐pyrrolidone) (PVP)/bis‐(4‐hydroxyphenyl)methane (BHPM) blends was studied. Fourier transform infrared spectroscopic examinations demonstrated that BHPM interacts with P2VPy and PVP through hydrogen‐bonding interactions. The addition of a sufficiently large amount of BHPM transformed an opaque blend with two glass‐transition temperatures (T_g's) to a transparent single‐T_g blend. Scanning electron microscopic studies showed that the transparent single‐T_g blend is micro‐phase‐separated at a scale of about 30 nm. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1815–1823, 2001     

Blends of polycarbonate and poly(ϵ‐caprolactone) and the determination of the polymer–polymer interaction parameter of the two polymers

The thermal properties of blends of polycarbonate (PC) and poly(ε‐caprolactone) (PCL) were investigated by differential scanning calorimetry (DSC). From the thermal analysis of PC‐PCL blends, a single glass‐transition temperature (T_g) was observed for all the blend compositions. These results indicate that there is miscibility between the two components. From the modified Lu and Weiss equation, the polymer–polymer interaction parameter (χ₁₂) of the PC‐PCL blends was calculated and found to range from −0.012 to −0.040 with the compositions. The χ₁₂ values calculated from the T_g method decreased with the increase of PC weight fraction. By taking PC‐PCL blend as a model system, the values of χ₁₂ were compared with two different methods, the T_g method and melting point depression method. The two methods are in reasonably good agreement for the χ₁₂ values of the PC‐PCL blends. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2072–2076, 2000     

Segmental and secondary dynamics in hydrogen‐bonded poly(4‐vinylphenol)/poly(methyl methacrylate) blends

Broadband dielectric spectroscopy was used to study the segmental (α) and secondary (β) relaxations in hydrogen‐bonded poly(4‐vinylphenol)/poly(methyl methacrylate) (PVPh/PMMA) blends with PVPh concentrations of 20–80% and at temperatures from ?30 to approximately glass‐transition temperature (T_g) + 80 °C. Miscible blends were obtained by solution casting from methyl ethyl ketone solution, as confirmed by single differential scanning calorimetry T_g and single segmental relaxation process for each blend. The β relaxation of PMMA maintains similar characteristics in blends with PVPh, compared with neat PMMA. Its relaxation time and activation energy are nearly the same in all blends. Furthermore, the dielectric relaxation strength of PMMA β process in the blends is proportional to the concentration of PMMA, suggesting that blending and intermolecular hydrogen bonding do not modify the local intramolecular motion. The α process, however, represents the segmental motions of both components and becomes slower with increasing PVPh concentration because of the higher T_g. This leads to well‐defined α and β relaxations in the blends above the corresponding T_g, which cannot be reliably resolved in neat PMMA without ambiguous curve deconvolution. The PMMA β process still follows an Arrhenius temperature dependence above T_g, but with an activation energy larger than that observed below T_g because of increased relaxation amplitude. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3405–3415, 2004     

The Relevance of the Collaborative Effect in Determining the Performances of Photorefractive Polymer Materials

A derivative of 2‐methylindole, 3‐[2‐(4‐nitrophenyl)ethenyl]‐1‐allyl‐2‐methylindole, NPEMI‐A, is studied for its photoconductivity and photorefractivity behaviour. Its blends with the organic polymer poly‐(2,3‐dimethyl‐N‐vinylindole), PVDMI, are also investigated. Due to the expected and devised mutual solubility of the two components of the blends, it is possible to carry out measurements with the weight percent of the chromophore NPEMI‐A changing from zero to 100. Films were produced by a squeezing process between two ITO‐covered glass sheets. No opacity phenomena, that are so common for many other organic blends due to the segregation of the dissolved chromophore, are observed. The photorefractive optical gain Γ₂ is obtained as a function of the chromophore content. Differential scanning calorimetry measurements (DSC) are also carried out to obtain the whole change of the glass transition temperature T_g as a function of the amount of chromophore contained in the blends. From the experimental trend of T_g a meaningful quantitative estimate of the value of the electrostatic interactions acting in the studied blends, is obtained. The importance of the value of T_g, and of the electrostatic interactions, in determining the extent of the photorefractivity is clearly evident. The results are compared for NPEMI‐A (Γ₂=210 cm^?1) and for NPEMI‐E (Γ₂ ≈ 2000 cm^?1) that has a N‐2‐ethylhexyl group instead of a N‐allyl group. The Pockels and Kerr contributions and—for the first time—a “collaborative effect” of the photorefractivity of NPEMI‐A are distinguished and quantitatively evaluated.     

Synthesis of hydroxyl‐terminated poly(ether ether ketone) with pendent tert‐butyl groups and its use as a toughener for epoxy resins

Hydroxyl‐terminated poly(ether ether ketone) with pendent tert‐butyl groups (PEEKTOH) was synthesized by the nucleophilic substitution reaction of 4,4′‐difluorobenzophenone with tert‐butyl hydroquinone with potassium carbonate as a catalyst and N‐methyl‐2‐pyrrolidone as a solvent. Diglycidyl ether of bisphenol A epoxy resin was toughened with PEEKTOHs having different molecular weights. The melt‐mixed binary blends were homogeneous and showed a single composition‐dependent glass‐transition temperature (T_g). Kelley–Bueche and Gordon–Taylor equations gave good correlation with the experimental T_g. Scanning electron microscopy studies of the cured blends revealed a two‐phase morphology. A sea‐island morphology in which the thermoplastic was dispersed in a continuous matrix of epoxy resin was observed. Phase separation occurred by a nucleation and growth mechanism. The dynamic mechanical spectrum of the blends gave two peaks corresponding to epoxy‐rich and thermoplastic‐rich phases. The T_g of the epoxy‐rich phase was lower than that of the unmodified epoxy resin, indicating the presence of dissolved PEEKTOH in the epoxy matrix. There was an increase in the tensile strength with the addition of PEEKTOH. The fracture toughness increased by 135% with the addition of high‐molecular‐weight PEEKTOH. The improvement in the fracture toughness was dependent on the molecular weight and concentration of the oligomers present in the blend. Fracture mechanisms such as crack path deflection, ductile tearing of the thermoplastic, and local plastic deformation of the matrix occurred in the blends. The thermal stability of the blends was not affected by blending with PEEKTOH. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 541–556, 2006     

Epoxy resin/poly(ϵ‐caprolactone) blends cured with 2,2‐bis[4‐(4‐aminophenoxy)phenyl]propane. I. Miscibility and crystallization kinetics

Crystalline thermosetting blends composed of 2,2′‐bis[4‐(4‐aminophenoxy)phenyl]propane (BAPP)‐cured epoxy resin (ER) and poly(?‐caprolactone) (PCL) were prepared via the in situ curing reaction of epoxy monomers in the presence of PCL, which started from initially homogeneous mixtures of diglycidyl ether of bisphenol A (DGEBA), BAPP, and PCL. The miscibility of the blends after and before the curing reaction was established with differential scanning calorimetry and dynamic mechanical analysis. Single and composition‐dependent glass‐transition temperatures (T_g's) were observed in the entire blend composition after and before the crosslinking reaction. The experimental T_g's were in good agreement with the prediction by the Fox and Gordon–Taylor equations. The curing reaction caused a considerable increase in the overall crystallization rate and dramatically influenced the mechanism of nucleation and the growth of the PCL crystals. The equilibrium melting point depression was observed for the blends. An analysis of the kinetic data according to the Hoffman–Lauritzen crystallization kinetic theory showed that with an increasing amorphous content, the surface energy of the extremity surfaces increased dramatically for DGEBA/PCL blends but decreased for ER/PCL blends. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1085–1098, 2003     

Phase behavior and crystallization of a poly(ethylene oxide)/cellulose acetate butyrate blend

The phase behavior of a partially miscible blend of poly(ethylene oxide) (PEO) and cellulose acetate butyrate (CAB) and the crystalline microstructure of PEO in the blend were studied with differential scanning calorimetry (DSC), optical microscopy, and synchrotron small‐angle X‐ray scattering (SAXS) methods. PEO/CAB showed a lower critical solution temperature (LCST) of 168 °C at the critical composition of PEO of 60 wt %. All blend compositions showed a single glass‐transition temperature (T_g) when they were prepared at temperatures lower than the LCST. However, with increasing CAB content, T_g of the blend changed abruptly at 70 wt % CAB; that is, a cusp existed. Below 70 wt % CAB, the change in T_g with blend composition was predicted by the Brau–Kovacs equation, whereas this change was predicted by the Fox equation at higher CAB contents. A gradual but small depression of the melting point of PEO in the blend with an increasing amount of CAB suggested that the PEO/CAB blends exhibited a weak intermolecular interaction. From DSC and SAXS experiments, it was found that amorphous CAB was incorporated into the interlamellar region of PEO for blends with less than 20 wt % CAB, whereas it was segregated to exist in the interfibrillar region in PEO for other blends with larger amounts of CAB. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1673–1681, 2002     

Glass transition and miscibility in blends of two semicrystalline polymers: Poly(aryl ether ketone) and poly(ether ether ketone)

Binary melt‐blended mixtures of two aryl ether ketone polymers (i.e., a new poly(aryl ether ketone) (code name PK99) and poly(ether ether ketone) (PEEK), have been studied. Polymer miscibility in glassy amorphous (or melt) domains has been demonstrated for the binary blend comprising of two aryl‐ether‐ketone‐type semicrystalline polymers. Composition‐dependent, single T_g was observed within full composition range in the PK99/PEEK blends, and the narrow T_g breadth also suggests that the scale of mixing was fine and uniform. To better resolve any possible overlapping T_g's, physical aging was imposed on a comparison set of blend samples for the purpose of improving detectability of overlapped multiple transitions if existing. The result still showed one single T_g. The relative sharp T_g and lack of cloud point transition suggest that the scale of molecular intermixing is good. Phase homogeneity was further confirmed using optical and scanning electron microscopy. The X‐ray diffractograms suggest that isomorphism does not exist in the PK99/PEEK blends and that the crystal forms of the respective polymers remain distinct and unchanged by the miscibility in the amorphous region. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1485–1494, 1999     

The glass transition in athermal poly(α‐methyl styrene)/oligomer blends

The glass transition behavior in athermal blends of poly(α‐methyl styrene) (PaMS) and its hexamer is investigated using differential scanning calorimetry (DSC). The results, along with previous data on similar blends of PaMS/pentamer, are analyzed in the context of the Lodge–McLeish self‐concentration model. A methodology is described to partition the calorimetric transition to obtain effective T_gs for each component of the blend. The dependences of these effective T_gs on overall blend composition are described by the Lodge–McLeish model, although the self‐concentration effect is less than expected based on the Kuhn length. The length scales of the cooperatively rearranging regions for the two components in the blends are also calculated adapting Donth's fluctuation model to the partitioned DSC transitions and are found to be similar for the two components and show a slight decrease at intermediate concentrations. The kinetics associated with the glass temperature, T_g, is examined by studying the cooling rate dependence of T_g for the pure components and the blends, as well as by examining the enthalpy overshoots in the heating DSC scans. It is observed that the cooling rate dependence of T_g in PaMS/hexamer blends at intermediate concentrations is similar to that of the hexamer, indicating that the kinetics of the glass transition for blends is dominated by the high mobility oligomeric component. Moreover, compared to the pure materials, the PaMS/hexamer blends exhibit a considerably depressed enthalpy overshoot, presumably resulting from their broader relaxation time distribution. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 418–430, 2008     

A thermodynamic analysis of specific interactions in blends of poly(styrene‐co‐N,N‐dimethylacrylamide) and poly(styrene‐co‐acrylic acid). Screening and self‐association effects

In a first step of this contribution, the observed glass transition temperature‐composition behavior of miscible blends of poly(styrene‐co‐N,N‐dimethylacrylamide) (SAD17) containing 17 mol % of N,N‐dimethylacrylamide and poly(styrene‐co‐acrylic acid) (SAA18, SAA27, and SAA32) containing increasing acrylic acid content, are analyzed according to theoretical approaches. Both Kwei and Brostow equations describe well the experimental data though better fits were obtained with the Brostow's approach. The specific interactions involved in these systems are a combination of intra and interassociation hydrogen bonding. The positive deviation from the linear mixing rule of T_g‐composition observed within the SAA18+SAD17 blend system, indicates that interassociation interactions are prevailing. More pronounced intra‐association interactions within the SAA32+SAD17 blend system led to a large negative deviation while a fine balance is established between these two types of interactions within the SAA27+SAD17 blend. A thermodynamic analysis was carried out according to the Painter‐Coleman association model. The miscibility and phase behavior of SAD17+SAA18 and SAD17+SAA27 blends are well predicted. However, this model predicts a partial miscibility of SAD17+SAA32 system. Finally, the fitting parameter free method developed by Coleman to predict the T_g‐composition behavior is applied. This method predicts fairly well the evolution trend of experimental T_gs of the SAA18+SAD17 and SAA27+SAD17 blend systems. However, the compositional dependence of SAA32+SAD17 blend T_g was not predictable by this method. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47:2074–2082, 2009     

A study of the kinetics of the microwave cure of a phenylethynyl‐terminated imide model compound and imide oligomer (PETI‐5)

The kinetic mechanism of the microwave cure of a simple phenylethynyl‐terminated imide model compound, 3,4′‐bis[(4‐phenylethynyl)phthalimido]diphenyl ether (PEPA‐3,4′‐ODA) and a phenylethynyl‐terminated imide oligomer (PETI‐5, M_n 5000 g/mol) was studied. Dielectric properties of the model compound and PETI‐5 were measured in the microwave range from 0.4 GHz to 3 GHz. FTIR was used to follow the cure of the model compound (PEPA‐3,4′‐ODA), while thermal analysis (DSC) was used to follow the cure of the PETI‐5 oligomer. The changes in room temperature IR absorbance of phenylethynyl triple bonds at 2214 cm⁻¹ of PEPA‐3,4′‐ODA as a function of cure time were measured after cure temperatures of 300, 310, 320, and 330 °C. The changes in the glass‐transition temperature, T_g, of PETI‐5 as a function of cure time were measured after cure at 350, 360, 370, and 380 °C, respectively. The T_g 's were determined to calculated the relative extent of cure, x, of the PETI‐5 oligomer according to the DiBenedetto equation. For the model compound, the reaction followed first order kinetics, yielding an activation energy of 27.6 kcal/mol as determined by infrared spectroscopy. For PETI‐5, the reaction followed 1.5th order, yielding an activation energy of 17.1 kcal/mol for the whole cure reaction, as determined by T_g using the DiBenedetto method. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2526–2535, 2000     

Complex phase behavior and state of miscibility in Poly(ethylene glycol)/Poly(l‐lactide‐co‐ε‐caprolactone) Blends

A miscibility and phase behavior study was conducted on poly(ethylene glycol) (PEG)/poly(l ‐lactide‐ε‐caprolactone) (PLA‐co‐CL) blends. A single glass transition evolution was determined by differential scanning calorimetry initially suggesting a miscible system; however, the unusual T_g bias and subsequent morphological study conducted by polarized light optical microscopy (PLOM) and atomic force microscopy (AFM) evidenced a phase separated system for the whole range of blend compositions. PEG spherulites were found in all blends except for the PEG/PLA‐co‐CL 20/80 composition, with no interference of the comonomer in the melting point of PEG (T_m = 64 °C) and only a small one in crystallinity fraction (X_c = 80% vs. 70%). However, a clear continuous decrease in PEG spherulites growth rate (G) with increasing PLA‐co‐CL content was determined in the blends isothermally crystallized at 37 °C, G being 37 µm/min for the neat PEG and 12 µm/min for the 20 wt % PLA‐co‐CL blend. The kinetics interference in crystal growth rate of PEG suggests a diluting effect of the PLA‐co‐CL in the blends; further, PLOM and AFM provided unequivocal evidence of the interfering effect of PLA‐co‐CL on PEG crystal morphology, demonstrating imperfect crystallization in blends with interfibrillar location of the diluting amorphous component. Significantly, AFM images provided also evidence of amorphous phase separation between PEG and PLA‐co‐CL. A true T_g vs. composition diagram is proposed on the basis of the AFM analysis for phase separated PEG/PLA‐co‐CL blends revealing the existence of a second PLA‐co‐CL rich phase. According to the partial miscibility established by AFM analysis, PEG and PLA‐co‐CL rich phases, depending on blend composition, contain respectively an amount of the minority component leading to a system presenting, for every composition, two T_g's that are different of those of pure components. © 2013 Wiley Periodicals, Inc. J. Polym. Sci. Part B: Polym. Phys. 2014 , 52, 111–121     

Phase behavior and interactions in blends of poly[(butylene adipate)-co-poly(butylene terephthalate)] copolyester with poly(4-vinyl phenol)

Miscibility with a linear T _g–composition relationship was proven for blend of poly(butylene adipate-co-butylene terephthalate) [P(BA-co-BT)] with poly(4-vinyl phenol) (PVPh). In comparison to the blends of PBA/PVPh and poly(butylene terephthalate) (PBT)/PVPh, the Kwei’s T _g model fitting on data for the P(BA-co-BT)/PVPh blend yields a q value between those for the PBA/PVPh and PBT/PVPh blends. The q values suggest that the interaction strength in the P(BA-co-BT)/PVPh blend is not as strong as that in the PBT/PVPh blend. Upon mixing the PVPh into the immiscible blend of PBA and PBT, the ternary PBA/PBT/PVPh blends only exhibits partial miscibility. Full-scale ternary miscibility in whole compositions is not possible owing to the significant ∆χ effect (χ _ij  – χ _ik ). The wavenumber shifts of the hydroxyl IR absorbance band indicates that the H-bonding strength is in decreasing order—PBT/PVPh > P(BA-co-BT)/PVPh > PBA/PVPh—and shows that the BA segment in the copolymer tends to defray interactions between P(BA-co-BT) and PVPh in blends.     

Development and characterization of reactive extruded PVC/polyacrylate blends

This paper describes a method to obtain polymer blends by the absorption of a liquid solution of monomer, initiator, and a crosslinking agent in suspension type porous poly(vinyl chloride) (PVC) particles, forming a dry blend. These PVC/monomer dry blends are reactively polymerized in a twin‐screw extruder to obtain the in situ polymerization in a melt state of various blends: PVC/poly(methyl methacrylate) (PVC/PMMA), PVC/poly(vinyl acetate) (PVC/PVAc), PVC/poly(butyl acrylate) (PVC/PBA) and PVC/poly(ethylhexyl acrylate) (PVC/PEHA). Physical PVC/PMMA blends were produced, and the properties of those blends are compared to reactive blends of similar compositions. Owing to the high polymerization temperature (180°C), the polymers formed in this reactive polymerization process have low molecular weight. These short polymer chains plasticize the PVC phase reducing the melt viscosity, glass transition and the static modulus. Reactive blends of PVC/PMMA and PVC/PVAc are more compatible than the reactive PVC/PBA and PVC/PEHA blends. Reactive PVC/PMMA and PVC/PVAc blends are transparent, form single phase morphology, have single glass transition temperature (T_g), and show mechanical properties that are not inferior than that of neat PVC. Reactive PVC/PBA and PVC/PEHA blends are incompatible and two discrete phases are observed in each blend. However, those blends exhibit single glass transition owing to low content of the dispersed phase particles, which is probably too low to be detected by dynamic mechanical thermal analysis (DMTA) as a separate T_g value. The reactive PVC/PEHA show exceptional high elongation at break (～90%) owing to energy absorption optimized at this dispersed particle size (0.2–0.8 µm). Copyright © 2005 John Wiley & Sons, Ltd.     

Thermal characterization and solid‐state 13C‐NMR investigation of blends of poly(N‐phenyl‐2‐hydroxytrimethylene amine) and poly(N‐vinyl pyrrolidone)

The miscibility and thermal properties of poly(N‐phenyl‐2‐hydroxytrimethylene amine)/poly(N‐vinyl pyrrolidone) (PHA/PVP) blends were examined by using differential scanning calorimetry (DSC), high‐resolution solid‐state nuclear magnetic resonance (NMR) techniques, and thermogravimetric analysis (TGA). It was found that PHA is miscible with PVP, as shown by the existence of a single composition‐dependent glass transition temperature (T_g) in the whole composition range. The DSC results, together with the ¹³C crosspolarization (CP)/magic angle spinning (MAS)/high‐power dipolar decoupling (DD) spectra of the blends, revealed that there exist rather strong intermolecular interactions between PHA and PVP. The increase in hydrogen bonding and in T_g of the blends was found to broaden the line width of CH—OH carbon resonance of PHA. The measurement of the relaxation time showed that the PHA/PVP blends are homogeneous at least on the scale of 1–2 nm. The proton spin‐lattice relaxation in both the laboratory frame and the rotating frame were studied as a function of the blend composition, and it was found that blending did not appreciably affect the spectral densities of motion (sub‐T_g relaxation) in the mid‐MHz and mid‐KHz frequency ranges. Thermogravimetric analysis showed that PHA has rather good thermal stability, and the thermal stability of the blend can be further improved with increasing PVP content. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 237–245, 1999     

Miscibility behavior and hydrogen bonding in blends of poly(vinyl phenyl ketone hydrogenated) and poly(2‐ethyl‐2‐oxazoline)

The miscibility behavior of poly(2‐ethyl‐2‐oxazoline) (PEOx)/poly(vinyl phenyl ketone hydrogenated) (PVPhKH) blends was studied for the entire range of compositions. Differential scanning calorimetry and thermomechanical analysis measurements showed that all the PEOx/PVPhKH blends studied had a single glass‐transition temperature (T_g). The natural tendency of PVPhKH to self‐associate through hydrogen bonding was modified by the presence of PEOx. Partial IR spectra of these blends suggested that amide groups in PEOx and hydroxyl groups in PVPhKH interacted through hydrogen bonding. This physical interaction had a positive influence on the phase behavior of PEOx/PVPhKH blends. The Kwei equation for T_g as a function of the blend composition was satisfactorily used to describe the experimental data. Pure‐component pressure–volume–temperature data were also reported for both PEOx and PVPhKH. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 636–645, 2004