ZrO2和Al2O3载体对Mo基催化剂上甲烷化反应性能的影响

通过共沉淀法制备了ZrO₂和Al₂O₃载体,采用等体积浸渍法制备了MoO₃质量分数为5%的Mo/ZrO₂和Mo/Al₂O₃催化剂,并用于甲烷化反应。在三种反应气氛下对两种预硫化的Mo基催化剂进行评价,发现ZrO₂载体均可显著促进甲烷化反应,同时能够促进水汽变换（WGS）反应。通过XRD、H₂-TPR、XPS和TEM等表征发现,两种载体上Mo物种的硫化程度以及暴露的活性位数量不同,从而导致两种催化剂上催化性能差异显著。与Mo/Al₂O₃相比,Mo/ZrO₂催化剂上的MoO₃更易被还原,硫化程度也更高,并且Mo⁴⁺的含量更高,Mo⁶⁺的含量更低。虽然ZrO₂载体上MoS₂尺寸较大,边位置的Mo比例有所降低,但是由于MoS₂沿ZrO₂颗粒表面弯曲生长,使得MoS₂基面成为反应的活性位;因此,Mo/ZrO₂催化剂在甲烷化与WGS反应中表现出更优异的催化性能。     

Preparation of crack-free ZrO2 membrane on Al2O3 support with ZrO2–Al2O3 composite intermediate layers

To develop porous alumina supported MF ZrO₂ membranes, ZrO₂–Al₂O₃ composite intermediate layers are considered in order to decrease stress creation during the processing and avoid cracks formation. The relation between distortion stress and sintering shrinkage was experimentally studied. And the cracks formation mechanism was qualitatively evaluated and discussed. Finally, crack-free YSZ membrane with pore size of 0.16 μm on the two ZrO₂–Al₂O₃ intermediate layers possessing a gradient composition was successfully prepared and characterized.     

Reduction kinetics of Mo/Al2O3 catalysts

Studies of the reduction kinetics of MoO₃ and Al₂O₃–MoO₃ catalysts in H₂ at 523–823 K indicate that molybdenum is present in Al₂O₃/MoO₃ in three forms: as Mo⁶⁺ in the Al₂O₃ lattice and as MoO₃ and Al₂(MoO₄)₃ phases. Activation energies of reduction E_act determined according to the Avrahmy-Erofeev equation, are reported.

---

MoO₃ Al₂O₃–MoO₃ H₂ 523–823 . Al₂O₃–MoO₃ : Mo⁶⁺ Al₂O₃ MoO₃ Al₂(MoO₄)₃, . -.

     

Hydrodechlorination of dichlorodifluoromethane (CFC-12) over Pd/Al2O3 and Pd-Au/Al2O3 catalysts

During an initial stage of the reaction of CCl₂F₂ with hydrogen on alumina-supported Pd and Pd-Au catalysts, an extensive defluorination occurs. However, at steady state, this undesired defluorination is greatly reduced; CH₄ and CH₂F₂ constitute the only major reaction products. A temperature programmed hydrogen treatment study shows retention of fluorine (and carbon) in used catalysts. This revised version was published online in June 2006 with corrections to the Cover Date.     

Oxidative addition of hydrogen in the “reduced” Mo/Al2O3 catalysts

An X-ray photoelectron spectroscopy study of Mo/Al₂O₃ catalysts prepared via [Mo^V ₂O₄(C₂O₄)₂(H₂O)₂]^2- complexes showed that after heating the catalysts with hydrogen in the spectrometer chamber, the position of the Mo3d line shifted to higher values of binding energy. This shift is interpreted as oxidative addition of hydrogen to the surface Mo species. A similar phenomenon was observed for a CO treated catalyst. A temperature-programmed desorption study has shown that hydrogen is strongly bounded to Mo and can only be removed from the catalysts at temperatures as high as 500°C. This revised version was published online in June 2006 with corrections to the Cover Date.     

TPR studies on steam reforming of 2-propanol on Rh/Al2O3, Ru/Al2O3 and Pd/Al2O3

Reaction pathways for steam reforming of 2-propanol (isopropyl alcohol, IPA) on Rh/Al₂O₃, Ru/Al₂O₃ and Pd/Al₂O₃ have been studied by temperature-programmed reactions (TPRs) of IPA and acetone in the presence of steam. The results of TPRs suggest that that of IPA on Rh/Al₂O₃ and Ru/Al₂O₃ proceeds via acetone, while the steam reforming of IPA on Pd/Al₂O₃ takes place via propene from acetone. This revised version was published online in August 2006 with corrections to the Cover Date.     

氧化铝载体硫酸化对锰铈催化剂SCR脱硝性能的影响

分别以硫酸改性前后的氧化铝为载体,采用浸渍法制备了锰铈催化剂,对其NH_3-SCR脱硝性能进行评价,并采用XRD、BET、NH_3-TPD、H_2-TPR以及FT-IR对催化剂进行了表征。结果表明,改性降低了金属的分散性和氧化性,增加了酸量,特别是B酸量;催化剂的最佳脱硝温度窗口向高温扩展,活性温度窗口范围变宽,并且,改性液浓度越大变化幅度越大。当反应温度在200-250℃时,未改性催化剂与采用0.2 mol/L硫酸改性的催化剂具有接近的催化活性,但改性后的催化剂具有更高的抗水抗硫活性,250℃时脱硝率可达70%。     

Cross metathesis of butene-2 and ethene to propene over Mo/MCM-22-Al2O3 catalysts with different Al2O3 contents

A series of 3.0Mo/MCM-22-Al2O3 catalysts with γ-Al2O3 contents in the range of 0-100 wt% were prepared and applied in the metathesis reaction of ethene and butene-2. Addition of γ-Al2O3 did not affect the structure of MCM-22 zeolite as evidenced by XRD and N2 adsorption measurements. It was deduced from TPR experiments that γ-Al2O3 phase favored the formation of polymolybdate or multilayered Mo oxide, while more Al2(MoO4)3 species were generated over MCM-22 zeolites. Alumina content in the support was directly related to the metathesis activity of ethene and butene-2 to propene. Mo species with higher valence (Mo⁶⁺or Mo⁵⁺) contributed more to the excellent performance of catalyst than metallic Mo. The best catalyst activity and stability was obtained over 3.0Mo/(MCM-22-30%Al2O3) under the reaction condition of 1.0 MPa and 125 ℃ using N2 as the pretreatment gas.     

Fischer-Tropsch synthesis over Ru/Al2O3 catalysts

Fischer-Tropsch syntheses (FTS) were carried out in a slurry phase over Ru/Al₂O₃ catalysts using hexadecane as a solvent. The outcome of the FTS was dependent on the oxide support, calcination temperature, synthesis gas composition and sulfur content. The addition of Mn/Na to Ru/Al₂O₃ was effective in raising the initial activity and C5+ selectivity, but after 20 hours, the performance of the modified catalyst was similar to that of the unmodified catalyst. An additional investigation involving the use of fresh vs used catalysts demonstrated that an agglomeration of the metallic Ru, at least in part, does occur during the reaction.     

钡改性对Cr_2O_3/Al_2O_3催化剂异丁烷脱氢性能的影响

采用浸渍法制备了不同BaO负载量的Cr_2O_3/Al_2O_3催化剂,利用XRD、BET、NH3-TPD和O2-TPO等表征方法对钡改性前后的催化剂进行了分析;在反应温度560℃、反应压力0.1MPa、催化剂用量10mL、GHSV=400h-1的条件下,在固定床反应器上考察了其异丁烷脱氢反应的性能。结果表明,钡的引入影响了活性组分Cr2O3的分散,导致了催化剂比表面积的降低,但影响并不显著;钡的引入降低了催化剂表面的酸性、减少了反应过程中催化剂的积炭,改善了催化剂的选择性,提高了催化剂的稳定性。当BaO负载量为3%时,催化剂的性能最佳。     

Sulfuration of Pt/Al2O3, Pt?Re/Al2O3 and Pt?Ir/Al2O3 catalysts

Three reforming catalysts Pt/Al₂O₃, Pt–Ir/Al₂O₃ and Pt–Re/Al₂O₃ have been sulfurated by H₂S and tested by their activities in benzene hydrogenation. By treatment at 500°C under hydrogen flow only a part of the initial activity of the non-sulfurated catalyst is retained. So only a part of the adsorbed sulfur is easily removed in these conditions. The remaining sulfur for each of the catalysts (Pt/Al₂O₃, Pt–Ir/Al₂O₃ and Pt–Re/Al₂O₃) gives the same atomic ratio of 0.5 sulfur atom per accessible metallic atom.

---

Pt/Al₂O₃, Pt–Ir/Al₂O₃ Pt–Pe/Al₂O₃ . 500°C H₂ . . ., . (Pt/Al₂O₃, Pt–Ir/Al₂O₃ Pt–Pe/Al₂O₃) 0,5.

     

Effect of H2S on pyridine HDN over Ir, Mo and Ir-Mo/Al2O3 sulfide catalysts

The effect of H₂S on hydrodenitrogenation (HDN) of pyridine over alumina supported Mo, Ir and mixed Ir-Mo sulfide catalysts was studied. The pyridine hydrogenation was inhibited by H₂S on all catalysts, while the cleavage of the C-N bond of intermediate piperidine was facilitated on the Mo and inhibited on the Ir and Ir-Mo catalysts. The promotional offect between Ir and Mo was observed in the piperidine cleavage both in the presence and absence of H₂S.     

Acidic properties of V2O5-WO3/ZrO2 catalysts

The adsorption of pyridine on V₂O₅−WO₃/ZrO₂ has been studied by FTIR. In V₂O₅/ZrO₂ (2 wt.%), the number of both Br?nsted and Lewis acidic sites increased with the addition of WO₃, while in V₂O₅/ZrO₂ (5 wt.%), Br?nsted sites increased and Lewis sites did not change.     

Kinetic studies of hydrogen and carbon monoxide adsorption on Re2O7/Al2O3 catalysts

Kinetic studies of hydrogen and carbon monoxide adsorption on reduced Re₂O₇/Al₂O₃ catalysts have revealed that its activation energy decreases with increasing reduction degree of rhenium oxide. Adsorption of gases is suggested to take place on metallic rhenium atoms.

---

- . , . , .

     

Sulfurization of Pt/Al2O3?Cl catalysts. IV. Adsorption sites of H2S on Al2O3, Al2O3?Cl and Pt/Al2O3?Cl

Chemisorption of H₂S on Al₂O₃, Al₂O₃–Cl and Pt/Al₂O₃–Cl has been studied by gravimetry and IR spectroscopy. The influence of the amount of Cl on the H₂S adsorption equilibrium value and the nature of the adsorption sites at low and high coverages are discussed.

---

H₂S Al₂O₃, Al₂O₃–Cl Pt/Al₂O₃–Cl . Cl H₂S, .

     

Investigation of the acidity of Ni/Al2O3 and Ni/SiO2?Al2O3 catalysts

Acidity of Ni-modified alumina and silica-alumina catalysts was determined using n-butylamine titration and pyridine adsorption methods. Strong influence of Ni²⁺ ions on the Brönsted acidity of silicaalumina was observed. Improved Brönsted acidity of such system was confirmed by the results of the test reaction.     

Study of reduced Mo/Al2O3 metathesis catalysts prepared via metal complexes

The Mo/Al₂O₃ catalysts for propene metathesis were prepared both via anchoring Mo complexes of various nuclearities and by conventional method of impregnation. The catalysts from metal complexes were found to be active in metathesis at ambient temperature after reduction with H₂ or CO at 400–500°C. The average oxidation state of Mo in the activated catalysts was determined with regard to oxygen consumption needed for oxidation of the reduced Mo species to Mo⁶⁺.     

Activity of MoSe2/Al2O3 catalysts in decomposition of thiophene and selenophene

The rate of thiophene decomposition was shown to be independent of the type of chalcogens used in catalysts MoX₂/Al₂O₃, where X = S, Se. On the contrary, the rate of selenophene decomposition was shown to be higher on catalysts MoSe₂ than that on MoS₂. This observation suggests that the decomposition proceeds on anion vacancies. The decomposition of either thiophene over MoSe₂ or selenophene over MoS₂ results in the formation of partially substituted chalcogenides. At that, the molar ratios of the substituted chalcogen to Mo were shown to coincide in both cases. The fact that the rate of the thiophene decomposition does not depend on the degree of anion exchange indicates that the decomposition is not associated with hydrogenolysis.     

Ring opening of methylcyclopentane over Al2O3 and SiO2 supported Rh catalysts

Hydrogenolytic ring opening of methylcyclopentane (MCP) was investigated on Rh/Al₂O₃ and Rh/SiO₂ catalysts, prepared by the incipient wetness method. Strong dependence can be seen in the yield and distribution of ring opening products as a function of temperature and hydrogen pressure. They depended also on the support used. The ring opening reaction required high hydrogen coverage, and was not random (hindered in the vicinity of the methyl group), thus, mainly 2-methylpentane (2MP) and 3-methylpentane (3MP) were formed. The fragments consisted of C₁–C₅ alkanes, with methane andi-pentane as main fragments. This means the possibility of breaking two C−C bonds during one sojourn of the reactant on the catalyst, both taking place far from the substituent. The loose positive correlation between the ratios ofi-pentane/n-pentane and 3MP/n-hexane seems to support this conclusion. Dedicated to Professor Pál Tétényi on the occasion of his 70th birthday