Electrocatalytic oxidation of nitric oxide at nano-TiO2/Nafion composite film modified glassy carbon electrode

A novel nanocrystalline TiO₂ (nano-TiO₂) and Nafion composite film modified glassy carbon electrode has been developed for the determination of nitric oxide (NO) radical in an aqueous solution. This modified electrode can be employed as a NO sensor with a low detection limit, fast response, high sensitivity and selectivity. Two apparent anodic peaks were observed at 0.67 and 0.95 V at the nano-TiO₂ modified glassy carbon electrode by differential pulse voltammetry (DPV). After further modification with a thin film of Nafion, which was capable of preventing some anionic interference such as nitrite and ascorbic acid, only one peak appeared and the peak current enhanced greatly. The chronocoulometric experimental results showed NO was oxidized by one-electron transfer reaction at the composite film modified electrode. The amperometric responses increased linearly with the concentrations of NO ranging from 3.6×10⁻⁷ mol/L to 5.4×10⁻⁵ mol/L. The detection limit was estimated to be 5.4×10⁻⁸ mol/L. In this sensor system, the modification film provides complete selectivity for NO over nitrite anions (NO₂⁻).     

Electrochemistry and electrocatalytic activity of catechin film on a glassy carbon electrode toward the oxidation of hydrazine

A very stable electroactive film of catechin was electrochemically deposited on the surface of activated glassy carbon electrode. The electrochemical behavior of catechin modified glassy carbon electrode (CMGCE) was extensively studied using cyclic voltammetry. The properties of the electrodeposited films, during preparation under different conditions, and the stability of the deposited film were examined. The charge transfer coefficient (α) and charge transfer rate constant (k _s) for catechin deposited film were calculated. It was found that the modified electrode exhibited excellent electrocatalytic activity toward hydrazine oxidation and it also showed a very large decrease in the overpotential for the oxidation of hydrazine. The CMGCE was employed to study electrocatalytic oxidation of hydrazine using cyclic voltammetry, rotating disk voltammetry, chronoamperometry, amperometry and square-wave voltammetry as diagnostic techniques. The catalytic rate constant of the modified electrode for the oxidation of hydrazine was determined by cyclic voltammetry, chronoamperometry and rotating disk voltammetry and was found to be around 10⁻³ cm s⁻¹ . In the used different voltammetric methods, the plot of the electrocatalytic current versus hydrazine concentration is constituted of two linear segments with different ranges of hydrazine concentration. Furthermore, amperometry in stirred solution exhibits a detection limit of 0.165 μM and the precision of 4.7% for replicate measurements of 40.0 μM solution of hydrazine.     

Surfactant effects on methanol oxidation at Pt–Ru/C coated glassy carbon electrode

The role of surfactants, cetyl trimethyl ammonium bromide (CTAB), sodium dodecyl sulphate (SDS) and Triton X-100 (in the catalyst), on methanol oxidation at commercial 50:50 Pt–Ru/C catalyst-coated glassy carbon has been studied using cyclic voltammetry, scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FT-IR). Surfactant containing catalysts showed a considerable reduction in the methanol oxidation potential. In terms of oxidation potential, better results (lower methanol oxidation potential) were observed in the order SDS > Triton X-100 > CTAB > no surfactant. SEM studies on the catalyst ink showed better homogeneity in the sample prepared using surfactant. This indicates better Pt Pt contact, which is likely to favour methanol adsorption and its oxidation. Hence, lowering of oxidation potentials for methanol oxidation could be seen with use of surfactants. Results of FT-IR on the catalyst ink showed definite changes in the frequencies in the case of Pt–Ru/C containing surfactants indicating definite interaction between catalyst and surfactant. Catalysts, with and without surfactants, yielded linear plots of concentration vs peak currents for methanol oxidation (0–2 M). With surfactant containing catalysts, reduction in methanol oxidation current was observed, and the order followed was the reverse of the above.     

甲醇在Pt-Sn/GC上的电催化氧化

直接甲醇燃料电池（DMFC）以环境友好的甲醇为燃料,具有广泛的应用前景。目前使用的阳极催化剂主要是铂族贵金属,成本高,寿命和活性较差,因此,研究出高活性催化剂仍是目前的热点。通常方法是向Pt中添加一种或多种亲氧金属如Ru或Sn等,制成二元或多元铂合金。本文采用循环伏安法在玻碳电极上修饰铂锡合金,金属用量少,操作方便,相比Pt／GC,对甲醇的氧化呈现了较高的催化活性。     

Electrochemical oxidation behavior of colchicine on a graphene oxide-Nafion composite film modified glassy carbon electrode

An electrochemical sensor, based on a graphene oxide (GO)-Nafion composite film modified glassy carbon electrode (GCE), was developed and used for detection of trace amounts of colchicine. Owing to the large surface area, good conductivity of GO and good affinity of Nafion, the sensor exhibited excellent electrocatalytic activity for the oxidation of colchicine, displaying a wide linear response from 5.0 × 10(-8) to 2.0 × 10(-5) mol L(-1) and a low detection limit of 1.5 × 10(-8) mol L(-1) in 0.1 mol L(-1) H(2)SO(4) solution. And this modified electrode exhibited a superior immunity from epinephrine, dopamine and ascorbic acid interference. The method was also applied successfully to detect colchicine in medicinal tablets.     

Dopamine sensor based on a glassy carbon electrode modified with a reduced graphene oxide and palladium nanoparticles composite

We report on a sensitive electrochemical sensor for dopamine (DA) based on a glassy carbon electrode that was modified with a nanocomposite containing electrochemically reduced graphene oxide (RGO) and palladium nanoparticles (Pd-NPs). The composite was characterized by scanning electron microscopy, energy dispersive spectroscopy, and electrochemical impendence spectroscopy. The electrode can oxidize DA at lower potential (234 mV vs Ag/AgCl) than electrodes modified with RGO or Pd-NPs only. The response of the sensor to DA is linear in the 1–150 μM concentration range, and the detection limit is 0.233 μM. The sensor was applied to the determination of DA in commercial DA injection solutions.

Amperometric detection of carbohydrates and thiols by using a glassy carbon electrode coated with Co oxide/multi-wall carbon nanotubes catalytic system

A glassy carbon electrode coated with cobalt oxide/multi-wall carbon nanotubes (MWCNT) system was used for the detection of carbohydrates and thiols. The modification of the glassy carbon electrode increased the anodic current response of these organic compounds and decreased their overvoltage. The amperometric responses were extremely stable with no loss of sensitivity over many days of storage. Such attractive performance characteristics indicate great promise for using this new catalytic system for monitoring in fast and simple way compounds of great interest for food industry, biotechnology and clinical diagnostics.     

Enhanced catalytic activity of ternary NiCoPd nanocatalyst dispersed on carbon nanotubes toward methanol oxidation reaction in alkaline media

Ternary NiCoPd nanocatalyst dispersed on multi-walled carbon nanotubes (CNTs), NiCoPd/CNTs, was synthesized using a simple and green sonochemical method. The as-prepared NiCoPd/CNT hybrids were characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and inductively coupled plasma-atomic emission spectrometry (ICP-AES). The electrochemical measurements revealed that the ternary NiCoPd/CNTs exhibited an enhanced electrocatalytic activity for the methanol oxidation reaction (MOR), much superior to those of the binary NiPd/CNT and CoPd/CNT, as well as monometallic Pd/CNT counterparts, which likely resulted from the synergistic function of the dopant metals of Ni and Co.     

In situ synthesis of Pt/carbon nanofiber nanocomposites with enhanced electrocatalytic activity toward methanol oxidation

Pt/carbon nanofiber (Pt/CNF) nanocomposites were facilely synthesized by the reduction of hexachloroplatinic acid (H(2)PtCl(6)) using formic acid (HCOOH) in aqueous solution containing electrospun carbon nanofibers at room temperature. The obtained Pt/CNF nanocomposites were characterized by TEM and EDX. The Pt nanoparticles could in situ grow on the surface of CNFs with small particle size, high loading density, and uniform dispersion by adjusting the concentration of H(2)PtCl(6) precursor. The electrocatalytic activities of the Pt/CNF nanocomposites were also studied. These Pt/CNF nanocomposites exhibited higher electrocatalytic activity toward methanol oxidation reaction compared with commercial E-TEK Pt/C catalyst. The results presented may offer a new approach to facilely synthesize direct methanol fuel cells (DMFCs) catalyst with enhanced electrocatalytic activity and low cost.     

Voltammetric determination of salbutamol on a glassy carbon electrode coated with a nanomaterial thin film

A rapid and convenient electrochemical method is described for the determination of salbutamol based on multi-carbon nanotubes (MWNT) film coated glassy carbon electrode (GCE). The electrochemical behavior of salbutamol at this modified electrode was studied by square wave voltammetry, which indicated that the oxidation peak potential of salbutamol shifted on 40 mV to less positive potential and the peak current increased 4.5 fold, in contrast to that at a bare electrode. Various experimental parameters such as pH value of supporting electrolyte, the amount of modifier, and accumulation time were optimized. Under optimal measurement conditions, there is a good linear relationship between the peak current (I _pa) and salbutamol concentration in the range from 8.0 × 10⁻⁷ to 1.0 × 10⁻⁵ M, and the detection limit is 2.0 × 10⁻⁷ M (S/N = 3) at 2 min accumulation. The method has been successfully employed to detect salbutamol in pharmaceutical formulations.     

Derivative potentiometric stripping analysis with a thin film of mercury on a glassy carbon electrode

Derivative potentiometric stripping analysis is based on the pre-concentration of metal analytes in a thin film of mercury on a glassy carbon electrode and subsequent measurement of the electrode potential subject to controlled transport of oxidant to the electrode surface. The mechanism for the stripping process with respect to oxidant concentration, electrode rotation rate and instrument parameters is discussed, together with analytical results and applications.     

Highly sensitive deoxynivalenol immunosensor based on a glassy carbon electrode modified with a fullerene/ferrocene/ionic liquid composite

We describe a sensitive electrochemical immunosensor for the detection of deoxynivalenol (DON). It is based on a glassy carbon electrode modified with a composite made from fullerene (C₆₀), ferrocene and the ionic liquid. The components were immobilized on the surface of the electrode using chitosan cross-linked with epichlorohydrin. Then, the antibody to DON was covalently conjugated to the surface which then was blocked with serum albumin. The performance of the immunosensor was investigated by cyclic voltammetry and electrochemical impedance spectroscopy. It offers good repeatability (RSD?=?1.2%), selectivity, a stability of more than 180?days, an impedimetric response to DON in the range of 1?pgmL^?1 to 0.3?ng?mL^?1, and a detection limit (at S/N?=?3) of 0.3?pgmL^?1. The limit of detection is better than that of GC, HPLC, GC-MS, HPLC-MS and LC-MS-MS. The effects of omitting C₆₀ or the ionic liquid were also examined. The results indicate that the sensitivity of the biosensor is 2-fold better if C₆₀ and ionic liquids are used. This demonstrates that C₆₀ facilitates electron transfer on the surface of the modified electrode due to its unique electrochemical properties, while the ionic liquid provides a biocompatible microenvironment for the antibody. This results in increased sensitivity and stability. The method was satisfactorily applied to the determination of DON in food samples.

Electrochemistry and electrocatalytic activity of polypyrrole/ferrocyanide films on a glassy carbon electrode

Functionalized polypyrrole films were prepared by incorporation of Fe(CN)₆ ³⁻ as doping anion during the electropolymerization of pyrrole at a glassy carbon electrode from aqueous solution. The electrochemical behavior of the Fe(CN)₆ ³⁻/Fe(CN)₆ ⁴⁻ redox couple in polypyrrole was studied by cyclic voltammetry. An obvious surface redox reaction was observed and dependence of this reaction on the solution pH was illustrated. The electrocatalytic ability of polypyrrole film with ferrocyanide incorporated was demonstrated by oxidation of ascorbic acid at the optimized pH of 4 in a glycine buffer. The catalytic effect for mediated oxidation of ascorbic acid was 300 mV and the bimolecular rate constant determined for surface coverage of 4.5 × 10⁻⁸ M cm⁻² using rotating disk electrode voltammetry was 86 M⁻¹ s⁻¹. Furthermore, the catalytic oxidation current was linearly dependent on ascorbic acid concentration in the range 5 × 10⁻⁴–1.6 × 10⁻² M with a correlation coefficient of 0.996. The plot of i _p versus v ^1/2 confirms the diffusion nature of the peak current i _p. Received: 12 April 1999 / Accepted: 25 May 1999     

A hydrogen peroxide biosensor with high stability based on gelatin-multiwalled carbon nanotubes modified glassy carbon electrode

A biosensor with high stability was prepared to determine hydrogen peroxide (H₂O₂). This hydrogen peroxide biosensor was obtained by modifying glassy carbon electrode (GCE) with a composite film composed of gelatin-multiwalled carbon nanotubes. Catalase (Cat) was covalently immobilized into gelatin-multiwalled carbon nanotubes modified GCE through the well-known glutaraldehyde (GAD) chemistry in order to enhance the stability of electrodes. The enzyme sensor can achieve direct electrochemical response of hydrogen peroxide. The cyclic voltammograms at different scan rates, electrochemical impedance spectroscopy (EIS), and scanning electron microscope (SEM) tests indicate that the enzyme sensor performs positively on increasing permeability, reducing the electron transfer resistance, and improving the electrode performance. The linear response of standard curve for H₂O₂ is in the range of 0.2 to 5.0 mM with a correlation coefficient of 0.9972, and the detection limit of 0.001 mM. A high operational and storage stability is demonstrated for the biosensor. The peak potential at room temperature in two consecutive weeks stays almost consistent, and the enzyme activity is kept stable even after 30 days in further study.     

Electrocatalytic oxidation of methanol on a glassy carbon modified electrode by bis(1,2-phenylenediamine) nickel(II) complex

Electrocatalytic oxidation of methanol on a glassy carbon electrode coated with Ni(II)-(1,2-phenylendiamine)₂ (GC/NiOPD), conditioned by the potential recycling in a potential range of 100–650 mV (vs. SCE) is studied by cyclic voltammetry in an alkaline medium (0.10 M NaOH). The results show that the NiOPD layer formed at the surface of the electrode behaves as an efficient electrocatalyst for the oxidation of methanol in the alkaline medium via the Ni(III) species with a cross exchange reaction occurring throughout the layer at a low concentration of methanol. The effects of various parameters such as potential scan rates, methanol concentration and NiOPD surface concentration on the electro-oxidation of methanol are also investigated.     

Determination of nitrite based on mediated oxidation at a carbon paste electrode modified with a ruthenium polymer

The use of carbon paste electrodes modified with [Ru(bpy)(2)(PVP)(10)Cl]Cl for the mediated detection of nitrite is described. This surface modifier substantially lowers the overpotential for nitrite oxidation, hence permitting its determination at a lower potential. Various electrode characteristics were optimized, including the modifier loading and the monitoring potential, using batch amperometry. Standard calibration curves yielded slopes of 0.30 microA/microM over the linear range 5 x 10(-8)-5 x 10(-4)M nitrite with a detection limit of 3 x 10(-8)M (1.38 ppb) nitrite. The modified electrode response was shown to be relatively stable over a period of 5 days with a signal diminution of 8%. Electrode-to-electrode precision was measured as 11.4%. Flow-injection studies indicated the suitability of this electrode as a detector in flowing streams.     

Nonenzymatic hydrogen peroxide sensor based on a glassy carbon electrode modified with electrospun PdO-NiO composite nanofibers

A glassy carbon electrode was modified with PdO-NiO composite nanofibers (PdO-NiO-NFs) and applied to the electrocatalytic reduction of hydrogen peroxide (H₂O₂). The PdO-NiO-NFs were synthesized by electrospinning and subsequent thermal treatment, and then characterized by scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. Factors such as the composition and fraction of nanofibers, and of the applied potential were also studied. The sensor exhibits high sensitivity for H₂O₂ (583.43 μA?·?mM^?1?·?cm^?2), a wide linear range (from 5.0 μM to 19 mM), a low detection limit (2.94 μM at an SNR of 3), good long term stability, and is resistant to fouling.

Voltammetric sensor for caffeine based on a glassy carbon electrode modified with Nafion and graphene oxide

A facile, one-step and template-free method has been developed for the electrodeposition of well-dispersed platinum nanoparticles (Pt-NPs) on a glassy carbon electrode. The effects of various inorganic anions and overpotential on the morphologies and dimensions of the final products were investigated. The resulting Pt-NPs show high electrocatalytic activity towards methanol oxidation and are less easily poisoned by carbon monoxide.