共聚型氯醇橡胶锂离子聚合物电解质的制备和性能

以共聚型氯醇橡胶(ECO)为基体, 通过在基体中溶解不同浓度的LiCF₃SO₃制备了一系列聚合物电解质. 利用差示扫描量热技术(DSC)研究了该体系锂盐浓度对聚合物电解质玻璃化转变温度的影响, 用傅里叶变换红外光谱(FTIR)研究了体系内锂盐与聚合物基体的相互作用. 结果表明, 在相同锂盐浓度下, ECO基聚合物电解质的室温离子电导率比传统的聚环氧乙烷(PEO)基聚合物电解质提高了2个数量级, 并且体系电导率在升降温循环测试中没有弛豫现象产生. 这是由于ECO基体的非结晶性所致.     

新型梳状聚甲基丙烯酸酯固态聚合物电解质的制备及导电性能研究

采用溶液聚合方法,以甲基丙烯酸甲酯、聚乙二醇单甲醚甲基丙烯酸酯为共聚单体,制备一种新型无规梳状聚合物,并研究了一系列掺杂不同含量高氯酸锂全固态聚合物电解质的导电性能.FTIR、1H-NMR结果证实了新型梳状聚合物具有无规梳状结构特征.DSC和XRD结果表明了聚合物电解质主要是以无定型状态存在.SEM和FTIR结果证实了当锂盐含量低于16 wt%时,锂盐在聚合物中具有良好的溶解性,ClO4-主要以单离子状态存在,此时聚合物电解质30℃离子电导率达到最大值,为4.81×10-5S/cm.当锂盐含量超过16wt%时,Li+ClO4-离子对含量明显增多,表明了锂盐溶解性能下降,同时聚合物电解质离子电导率显著下降,这主要是锂盐增加导致离子的缔合增强,不利于离子的传导所致.     

P(VAc-MMA)为基体的聚合物电解质研究

以醋酸乙烯酯(VAc)和甲基丙烯酸甲酯(MMA)为单体, 采用半连续种子乳液聚合法制备了无规共聚物聚(醋酸乙烯酯-甲基丙烯酸甲酯)[P(VAc-MMA)], 并以此聚合物为基体制备了聚合物电解质. 用红外光谱(FTIR)、核磁共振氢谱(¹H NMR)、扫描电镜(SEM)、差热/热重分析(DSC/TG)、X射线衍射(XRD)、机械性能测试和电化学交流阻抗等方法对聚合物和聚合物电解质的性质进行了研究. 测试结果表明: VAc和MMA聚合生成P(VAc-MMA); 聚合物膜含有大量微孔结构, 利于离子传输; 聚合物电解质膜具有优良的热稳定性和机械强度; 25 ℃下, 最高的离子电导率达到了1.27× 10^－3 S•cm^－1; 离子电导率随着温度的升高而迅速增加, 电导率-温度曲线符合Arrhenius方程.     

聚醚聚氨酯/低聚醚硫酸盐电解质的导电性能

聚合物固体电解质;聚二氧戊环;聚醚聚氨酯/低聚醚硫酸盐电解质的导电性能;离子电导率;     

新型单离子聚醚/聚氨酯固体电解质制备及其离子导电性

磺化聚醚;离子电导率;聚合物;新型单离子聚醚/聚氨酯固体电解质制备及其离子导电性     

纳米SiO2复合的梳状聚醚聚合物电解质的导电性能研究

于含锂盐的梳状聚醚聚合物电解质添加纳米S iO2制备复合聚合物电解质.并分别使用DSC和XRD研究S iO2对聚合物链段运动能力的影响.电导率测试表明,在相同的锂盐浓度下,加入5%的纳米S iO2后,聚合物电解质具有最高的离子电导率,30℃时为7.8×10-5S/cm,80℃时达到4.5×10-4S/cm.与未添加S iO2的聚合物电解质相比,电导率提高了30%~60%.TGA测定给出该聚合物的热分解温度为300℃左右,显示出良好的安全性能.     

原位聚合制备的离子液体/聚合物电解质的研究

采用原位聚合制备出新型的BMIPF6/PMMA聚合物电解质透明弹性膜. 研究结果表明, BMIPF6/PMMA聚合物电解质体系在305 ℃时仍具有较好的热稳定性, 其安全性能优于含有机溶剂的传统非水电解质体系. 随着离子液体含量的增加, 其玻璃化转变温度逐渐减小, 离子电导率升高; 且离子电导率与温度的关系服从VTF方程. 其中, 当BMIPF6的质量分数为50%时, 该聚合物电解质的室温离子电导率高达0.15 mS/cm.     

新型复合聚合物电解质离子导电行为的研究

PEG600和CH₂Cl₂通过Williamson缩聚反应,生成主链柔顺的PEG共聚物.¹H NMR测试表明其以[CH₂O(CH_2>CH₂O)¹³]为重复结构单元.与聚合物质量含量8%的气相SiO₂及适量的LiN(CF₃SO₂)2掺杂,制备一系列新型复合聚合物电解质.通过AC阻抗研究离子电导率,提出适合本体系的等效电路.该体系具有良好的成膜性能与热稳定性能,电导率比传统的PEO/盐体系高2～3个数量级.离子电导率随着温度的升高而增加,低温电导率增加较快,高温电导率增加较慢,呈非Arrhenius变化.在EO/Li=13～34:1(摩尔比)范围内,离子电导率随着盐浓度的变化出现两个峰值,低盐浓度的峰值较高.在303 K, EO/Li=28:1时,最大离子电导率接近10^-4 S/cm.     

锂离子聚合物常温固体电解质的研究进展

综述了锂离子电池聚合物常温固体电解质的最新研究进展。主要关注的是电化学性能,尤其是室温下的离子电导率。对性能较好的聚合物固体电解质体系进行了概述。     

HBPS-PEO多臂星形聚合物电解质的合成及离子导电性的研究

通过叠氮化超支化聚苯乙烯(HBPS-N3)与端炔基聚乙二醇单甲醚(ay-PEO)的点击反应,合成了以超支化聚苯乙烯(HBPS)为核、不同分子量的聚氧化乙烯(PEO)为臂的多臂星形聚合物(HBPS-PEO),并利用ATR-FTIR,1H-NMR,GPC对合成的星形聚合物的结构进行了表征.将该种星形聚合物与双三氟甲基磺酰亚胺锂(LiTFSI)进行复合,制备了星形聚合物为基体的聚合物电解质,通过交流阻抗技术和DSC对该聚合物电解质的离子导电性能及热性能进行了研究.结果表明,星形结构可以在一定程度上抑制结晶的形成,这种新型的星形聚合物电解质的室温电导率明显高于相应的线形聚合物电解质,当n(EO)/n(Li)=40,PEO臂的分子量为1000时,该星形聚合物电解质的离子电导率最高,30℃时为6.7×10-5Scm-1,40℃时可以达到1.2×10-4Scm-1;TGA结果表明,制备的星形聚合物的初始分解温度(Tonset)都高于360℃,具有良好的热稳定性.     

高分子固体电解质LiNO_3-LiOOCCH_3/聚丙烯酸锂的合成与性能研究

以丙烯酸和氢氧化锂为原料用反相乳液聚合法合成聚丙烯酸锂 (PAALi) ,将其熔于低共熔盐 (一定比例的LiNO3 LiOOCCH3混合物 )中得到新型高分子固体电解质 (SPE) ,用XRD、IR、DTA、TG DTG等技术进行了表征 ,讨论了影响合成PAALi工艺及新型固体电解质电阻率的主要因素 ,在LiNO3 LiOOCCH3摩尔比为 1∶1时 ,将其按质量百分比 80∶2 0与聚丙烯酸锂混合均匀并熔融 ,得到的电解质其室温离子电导率可达 2× 10 - 5S·cm- 1 ,大量低共熔盐的加入可明显提高SPE的离子导电率 .XRD、DTA及TG DTG结果表明低共熔盐与聚丙烯酸锂形成了新的配合物     

用于锂离子电池聚合物电解质的组成、结构和性能

聚合物电解质是全固态锂离子电池的重要组成部分, 其电导率对电池的性能有很重要的影响.本文综述了聚合物电解质的组成、结构和性能对锂 离子电池导电率影响的最新研究进展,特别是介绍了聚合物-碱金属盐复合电解质和聚离子体电解质两个体系的研究进展.     

纳米复合全固态聚膦腈电解质

为了进一步提高聚合物电解质的室温离子电导率和锂离子的迁移数,通过对纳米二氧化硅的表面修饰,并采用可聚合的带氧化乙烯-氧化丙烯共聚侧链取代的聚膦腈大单体制备了纳米复合的全固态电解质.通过X射线光电子能谱,扫描电镜,差热扫描分析对纳米复合电解质的性能和形貌进行了分析,并通过交流阻抗考察了电解质与电极间的界面稳定性,用循环伏安表征了电解质的电化学稳定窗口,考察了锂盐含量对电解质离子电导率的影响,测试了电解质的离子电导率随温度的关系,并对锂离子的迁移数进行了测定.研究结果表明,通过纳米复合的方法,提高了聚合物电解质的离子电导率,降低了界面电阻,提高了锂离子迁移率.     

Synthesis and properties of all solid polymer electrolytes based on poly(vinyl acetate‐co‐acetyl ethylene oxide acrylate)

Poly(acetyl ethylene oxide acrylate‐co‐vinyl acetate) (P(AEOA‐VAc)) was synthesized and used as a host for lithium perchlorate to prepare an all solid polymer electrolyte. Introduction of carbonyl groups into the copolymer increased ionic conductivity. All solid polymer electrolytes based on P(AEOA‐VAc) at 14.3 wt% VAc with 12wt% LiClO₄ showed conductivity as high as 1.2 × 10^?4 S cm^?1 at room temperature. The temperature dependence of the ionic conductivity followed the VTF behavior, indicating that the ion transport was related to segmental movement of the polymer. FTIR was used to investigate the effect of the carbonyl group on ionic conductivity. The interaction between the lithium salt and carbonyl groups accelerated the dissociation of the lithium salt and thus resulted in a maximum ionic conductivity at a salt concentration higher than pure PAEO‐salts system. Copyright © 2010 John Wiley & Sons, Ltd.     

聚苯并咪唑-锂盐-聚乙二醇单甲醚共混全固态聚合物电解质的制备及性能

使用共混后浇铸成膜的方法,制备了聚苯并咪唑-锂盐-聚乙二醇单甲醚组成的锂离子电池共混全固态聚合物电解质。通过傅里叶红外光谱(FT-IR)、X射线衍射(XRD)、差示扫描量热(DSC)、拉伸与交流阻抗测试表征了共混全固态电解质的结构与性能。研究了不同锂盐以及各组分含量对共混全固态电解质的力学性能与电导率的影响。结果表明:聚苯并咪唑与聚乙二醇单甲醚之间存在氢键;共混全固态电解质中聚乙二醇单甲醚处于无定形态;锂盐的加入使聚乙二醇单甲醚的玻璃化转变温度下降;聚乙二醇单甲醚含量越高,共混膜强度越低,电导率越高,并且使用三氟甲磺酸锂作为锂盐时其电导率最高,室温下可以达到3.58×10~(-5) S/cm,高温下可以达到3.3×10~(-3) S/cm,高温下满足对锂离子电池的使用需求。     

Dual-phase solid polymer electrolytes prepared from styrene–butadiene copolymer latices

A new dual-phase solid polymer electrolyte system has been proposed. In this system, a network of ion pathways is formed in a low-polarity, host polymer matrix. A series of electrolytes were prepared from styrene-butadiene copolymer latices with dissolved lithium salts. Polymer films were formed from these latices, and then impregnated with γ-butyrolactone (γ-BL) or γ-butyrolactone/dimethoxyethane mixture (γ-BL/DME), giving latex polymer electrolytes. The ionic conductivity of the polymer electrolyte system increased with increasing solvent content, although a distinct percolation threshold was not measured. Ionic conductivity also increased with the use of DME cosolvent, with the highest conductivity being 1.4 × 10^?4S/cm. Complex impedance diagrams are discussed. The diagrams show significant deviations from the ideal. TEM/SEM observations are consistent with the desired dual-phase morphology. © 1993 John Wiley & Sons, Inc.     

New fluorine-containing plasticized low lattice energy lithium salt for plastic batteries

The synthesis of a new plasticized low lattice energy lithium salt (PLI), structurally related to lithium bis(trifluoromethylsulfonyl)imide (LiTFSI), is described. Incorporation of the plasticizing moiety in a single salt molecule greatly simplifies the solid polymer electrolyte (SPE) processing formulation without compromising performance. Thermally and electrochemically stable polymer electrolyte films of PLI exhibit good ionic conductivity, though somewhat lower than that for LiTFSI. The pentafluorophenyl analog of LiTFSI, prepared by two approaches, exhibits behavior similar to that of LiTFSI.     

Influence of PEG-borate ester on thermal property and ionic conductivity of the polymer electrolyte

We have focused on the poly(ethylene glycol) (PEG)-borate ester as a new type plasticizer for solid polymer electrolyte for lithium ion secondary battery. Adding the PEG-borate ester into the electrolyte shows the increase in the ionic conductivity of the polymer electrolyte. By measuring the glass-transition temperature of the polymer electrolytes with DSC, it is found that the increase in ionic conductivity of the polymer electrolyte is due to the increase in ionic mobility. By investigating the temperature dependence of the ionic conductivity of the polymer electrolytes using William-Landel-Ferry type equation, we considered that the PEG-borate ester does not have any influence for dissociation of Li-salt. This revised version was published online in August 2006 with corrections to the Cover Date.     

Towards the mechanism of Li<Superscript>+</Superscript> ion transfer in the net solid polymer electrolyte based on polyethylene glycol diacrylate–LiClO<Subscript>4</Subscript>

Ion transport in the new three-dimensional network polymer electrolytes that are completely amorphous in the solid state has been studied on the example of the matrix model with a monomer—polyethylene glycol diacrylate, cross-linked by radical polymerization. The nature of ionic conductivity in solid polymer electrolytes based on polyethylene glycol diacrylate at different concentrations of salt LiClO₄ was studied by methods of electrochemical impedance, differential scanning calorimetry analysis, Fourier transform infrared spectroscopy and quantum chemical modeling. The maximum value of conductivity in the range of 20–100 °C is realized at 20 wt% content of LiClO₄. The reason for the low conductivity of the SPE studied is the small degree of dissociation of contact ion pairs. At the increase in the salt content associates of contact pairs Li⁺ClO ₄ ^? , dimers and trimers (at LiClO₄ >20 wt%) are formed. The appearances of trimers are accompanied by a decrease in conductivity due to lowering of contact pair content.     

Conductive networked polymer gel electrolytes composed of poly(meth)acrylate,lithium salt,and ionic liquid

Self‐standing films of (meth)acrylate‐based polymer gel electrolytes with high ionic liquid content (80 wt %) were prepared by in situ thermally or photo induced radical copolymerization of mono‐functional and di‐functional (meth)acrylates in an ionic liquid in the presence/absence of a lithium salt. Their ionic conductivity, thermal property, mechanical property, and flammability were examined. 1‐Ethyl‐3‐methylimidazolium bis(trifluoromethanesulfonyl)imide (EMImTFSI) or 1‐ethyl‐3‐methylimidazolium bis(fluorosulfonyl)imide (EMImFSI) was used as the ionic liquid, and lithium bis(trifluoromethanesulfonyl)imide LiTFSI was used as the lithium salt. The obtained films were semitransparent and flexible with good to moderate thermal stability and mechanical strength with high ionic conductivity. The EMImFSI‐containing gel electrolytes showed higher ionic conductivity than the corresponding EMImTFSI‐containing gel electrolytes. The ionic conductivity in the acrylate‐based gel electrolytes was slightly increased by addition of lithium salt, while that in the corresponding methacrylate‐based electrolytes was decreased significantly. The flame test showed the ionic liquid containing networked polymer gel electrolytes to have low if any flammability and was therefore confirmed to be highly safe. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012